Facet-Dependent Catalytic Activity of Platinum Nanocrystals for Triiodide Reduction in Dye-Sensitized Solar Cells

Platinum (Pt) nanocrystals have demonstrated to be an effective catalyst in many heterogeneous catalytic processes. However, pioneer facets with highest activity have been reported differently for various reaction systems. Although Pt has been the most important counter electrode material for dye-sensitized solar cells (DSCs), suitable atomic arrangement on the exposed crystal facet of Pt for triiodide reduction is still inexplicable. Using density functional theory, we have investigated the catalytic reaction processes of triiodide reduction over {100}, {111} and {411} facets, indicating that the activity follows the order of Pt(111) > Pt(411) > Pt(100). Further, Pt nanocrystals mainly bounded by {100}, {111} and {411} facets were synthesized and used as counter electrode materials for DSCs. The highest photovoltaic conversion efficiency of Pt(111) in DSCs confirms the predictions of the theoretical study. These findings have deepened the understanding of the mechanism of triiodide reduction at Pt surfaces and further screened the best facet for DSCs successfully.

An effective three-dimensional ordered mesoporous ZnCo2O4 as electrocatalyst for Li-O2 batteries

Three-dimensional ordered mesoporous (3DOM) ZnCo₂O₄ materials have been synthesized via a hard template and used as bifunctional electrocatalysts for rechargeable Li-O₂ batteries. The as-prepared ZnCo₂O₄ nanoparticles possess a high specific surface area of 127.2 m² g^-1 and a spinel crystalline structure. The Li-O₂ battery utilizing 3DOM ZnCo₂O₄ shows a higher specific capacity of 6024 mAh g^-1 than that with pure Ketjen black (KB). Moreover, the ZnCo₂O₄-based electrode enables much enhanced cyclability with a smaller discharge-recharge voltage gap than that of the carbon-only cathode. Such excellent catalytic performance of ZnCo₂O₄ could be associated with its larger surface area and 3D ordered mesoporous structure

Application of a cw quantum cascade laser CO2 analyser to catalytic oxidation reaction monitoring

Catalytic oxidation reaction monitoring has been performed for the first time with a trace gas carbon dioxide analyser based on a continuous wave (cw), thermoelectrically cooled (TEC), distributed feedback (DFB) quantum cascade laser (QCL) operating at around 2307 cm^-1. The reaction kinetics for carbon monoxide oxidation over a platinum catalyst supported on yttria-stabilised zirconia were followed by the QCL CO₂ analyser and showed that it is a powerful new tool for measuring low reaction rates associated with low surface area model catalysts operating at atmospheric pressures. A detection limit was determined of 40 ppb (1 standard deviation) for a 0.1 s average and a residual absorption standard deviation of 1.9×10^-4. © 2012 Springer-Verlag.

Carbons, Ionic Liquids, and Quinones for Electrochemical Capacitors

Carbons are the main electrode materials used in supercapacitors, which are electrochemical energy storage devices with high power densities and long cycling lifetimes. However, increasing their energy density capacity will improve their potential for commercial implementation.
In this regard, the use of high surface area carbons and high voltage electrolytes are well known strategies to increase the attainable energy density, and lately ionic liquids have been explored as promising alternatives to current state of the art acetonitrile-based electrolytes. Also, in terms of safety and sustainability ionic liquids are attractive electrolyte materials for supercapacitors. In addition, it has been shown that the matching of the carbon pore size with the electrolyte ion size further increases the attainable electrochemical double layer (ECDL) capacitance and energy density.
The use of pseudocapacitive reactions can significantly increase the attainable energy density, and quinonic-based materials offer a potentially sustainable and cost effective research avenue for both the electrode and the electrolyte.
This perspective will provide an overview of the current state of the art research on supercapacitors based on combinations of carbons, ionic liquids and quinonic compounds, highlighting performances and challenges and discussing possible future research avenues. In this regard, current interest is mainly focused on strategies which may ultimately lead to commercially competitive sustainable high performance supercapacitors for different applications including those requiring mechanical flexibility and biocompatibility.

Characterization of the toxic potential of nanomaterials using in vitro cell models

Os nanomateriais são estruturas com uma ou mais dimensões inferiores a 100 nanómetros. Devido à sua pequena dimensão, as nanopartículas apresentam atributos únicos, tais como a sua elevada área superficial relativamente à sua massa, reactividade ou força tênsil. Estas características influenciam grandemente algumas das propriedades dos nanomateriais, como a sua hidrofobicidade, carga ou toxicidade. As propriedades das nanopartículas tornam-nas também muito úteis para o Homem, sendo aplicadas em medicina, farmácia, electrónica, cosmética, vestuário e biotecnologia, entre outras. O aumento de produção e utilização de nanomateriais tem vindo a aumentar também a possibilidade de exposição humana a este tipo de partículas, levando a preocupações relativas ao risco de toxicidade aguda ou crónica. A exposição humana pode ocorrer por diversas vias, sendo as mais relevantes a via inalatória, ingestão ou contacto com a pele. Dependendo do material e do órgão-alvo, a exposição a nanomateriais pode conduzir a diferentes consequências biológicas: a nível dos órgãos, os nanomateriais podem levar a inflamação ou a supressão do sistema imunitário e, a nível celular e molecular, a perturbações na estrutura e integridade do genoma, assim como a interacções com moléculas biológicas e inibição da actividade proteica, entre outras consequências. Um dos nanomateriais mais utilizados são os nanotubos de carbono. Estes são constituídos por grafite cilíndrica disposta numa única camada (designados nanotubos de carbono de parede simples) ou em várias (nanotubos de carbono de parede múltipla). Os nanotubos de carbono apresentam propriedades como resistência e condutividade que os tornam muito úteis em aplicações como aparelhos electrónicos, vestuário ou biomedicina; cada vez mais, portanto, se torna provável a exposição ocupacional ou ambiental a este material. A semelhança estrutural destas partículas com fibras de amianto conduziu a questões relativas à sua segurança, pelo que já foram elaborados diversos estudos relativos aos seus efeitos biológicos. Alguns trabalhos sugerem que os nanotubos de carbono têm a capacidade de produzir toxicidade associada a lesões físicas, à produção de danos oxidativos por interacção com mecanismos celulares, ou a morte celular. Outros trabalhos defendem que estas partículas não causam toxicidade relevante. O projecto de dimensão europeia “NANoREG” surgiu da necessidade de ser desenvolvida legislação e regulamentação apoiadas em conhecimento científico e adequadas à produção e ao uso actual de nanomateriais. Este trabalho teve como objectivos principais a determinação do potencial cito- e genotóxico de um conjunto de nanotubos de carbono de parede múltipla (designados NM-400 a NM-403), e a consequente tentativa de associar este potencial às características físico-químicas dos nanomateriais. Com este objectivo, a exposição por via inalatória foi analisada, pelo uso de duas linhas celulares in vitro provenientes de tecidos do tracto respiratório: epitélio pulmonar (células A549) e epitélio brônquico (células BEAS-2B). A citotoxicidade dos nanotubos de carbono foi analisada com base em três parâmetros. Em primeiro lugar, as células foram contadas após a exposição aos nanomateriais utilizando o corante azul de tripanao para excluir as células inviáveis; a contagem foi realizada 3 e 24 horas após a exposição das células aos nanotubos. Os resultados deste ensaio apontam para a ausência de citotoxicidade após a exposição mais curta, e dados inconsistentes após a mais longa. Em segundo lugar, foi realizado o ensaio clonogénico, que se baseia na capacidade das células de se dividirem após a exposição ao agente em estudo. Este ensaio só foi realizado nas células A549 pois as BEAS-2B não permitem a formação de colónias. Os resultados apontam para uma citotoxicidade após a exposição a todos os nanomateriais, cuja intensidade se relaciona directamente com o tamanho das partículas, assim como ao seu diâmetro e área de superfície. Em terceiro lugar, foram calculados dois índices de viabilidade no ensaio dos Micronúcleos, cujo objectivo é avaliar se as células se dividiram durante a exposição aos nanomateriais em comparação com o controlo, e cujos resultados apresentam incoerências em relação aos outros já referidos. Estes dados podem ser justificados pelas diferenças existentes entre os ensaios, como o tempo de exposição ou a densidade celular. Os efeitos genotóxicos dos nanomateriais foram avaliados com recurso aos ensaios do cometa e dos micronúcleos. O primeiro detecta lesões pequenas e reversíveis nas cadeias de DNA, ao passo que o segundo detecta efeitos irreversíveis ao nível cromossómico, tais como quebras ou perdas de cromossomas. Os resultados do ensaio do cometa sugerem que nenhum dos nanomateriais testados é genotóxico, uma vez que em ambas as linhas celulares e em ambos os tempos de exposição, os resultados são negativos. O ensaio dos micronúcleos, por outro lado, aponta para existência de genotoxicidade de dois dos nanomateriais (NM-401 e NM-402) nas células A549, mas não em células BEAS-2B. Uma possível explicação para estes dados aparentemente contraditórios pode residir na hipótese de estes nanotubos de carbono serem compostos com efeitos aneugénicos, mas não clastogénicos: o ensaio dos micronúcleos permite a detecção de ambos os mecanismos de acção, ao passo que o ensaio do cometa só revela a quebra de cadeias de DNA. Outra justificação para os resultados é a possível influência da perda de viabilidade das células analisadas. Com base nos dados do ensaio clonogénico, estas partículas apresentam elevada citotoxicidade, pelo que os resultados dos ensaios de genotoxicidade, em particular do Ensaio do Cometa, poderão ser afectados por estes efeitos. O meio de cultura usado para expor as células aos nanomateriais também é um parâmetro muito relevante na sua toxicidade. Neste trabalho, foram usados meios de cultura com proteínas, que podem ser adsorvidas pelas partículas e formar uma “corona” em seu redor; este processo pode alterar propriedades importantes dos nanomateriais, entre os quais o seu potencial efeito biológico. Também o método usado para conseguir uma dispersão homogénea de nanomateriais pode conduzir a diferenças nos resultados dos ensaios de toxicidade. Neste estudo, foram observados alguns problemas relativos à perda de homogeneidade das dispersões de nanotubos de carbono, o que pode ter conduzido a que as células fossem expostas a massas de partículas de grandes dimensões conjuntamente com partículas individualizadas. O período durante o qual as células são expostas ao nanomaterial é também um aspecto essencial na produção de efeitos tóxicos. Resumindo, este projecto forneceu informações relativas à toxicidade dos nanotubos de carbono que, complementadas pelas conclusões dos restantes parceiros do projecto europeu, poderão contribuir significativamente para a avaliação de risco e criação de legislação relativamente à utilização de nanomateriais. Na linha celular BEAS-2B, nenhum destes nanomateriais parece produzir efeitos tóxicos, quer a nível de célula, quer a nível de genoma, nas condições experimentais utilizadas. Nas células A549, por outro lado, os três nanomateriais testados parecem ser acentuadamente citotóxicos, e dois deles (NM-401 e NM-402) são também genotóxicos. Em relação a perspectivas futuras, pode-se concluir que nem todos os ensaios de toxicidade existentes actualmente são adequados à análise de nanopartículas, pelo que novas metodologias devem ser desenvolvidas e complementadas por ensaios in vivo. Todos os estudos envolvendo nanomateriais deverão também descrever as características físico-químicas dos materiais usados, de forma a se poderem comparar os resultados com os de outros trabalhos.

Development of 2-oxazoline-based hydrogels and porous polyester microparticles in scCO2

Thesis submitted to Faculdade de Ciências e Tecnologia from Universidade Nova de Lisboa in partial fulfillment of the requirements for the obtention of the degree of Master of Science in Biotechnology

Surface properties and catalytic activity of vanadia supported on samaria

Sm2O3 - vanadia catalysts have been prepared by wet impregnation method using NH4VO3 solution. The surface properties of the prepared catalysts have been studied using FTIR. XRD. surface area and pore volume data. The acid-base properties of the system have been investigated by titrimetric method using Hammett indicators. adsorption of electron acceptors as well as decomposition of cyclohexanol. Phenol alkylation reaction by methanol has been carried out to investigate the catalytic activity. It has been observed that the selectivity of the products depends upon the composition of the supported system

Glucoamylase immobilized on montmorillonite: influence of nature of binding on surface properties of clay-support and activity of enzyme

Glucoamylase was immobilized on acid activated montmorillonite clay via two different procedures namely adsorption and covalent binding. The immobilized enzymes were characterized by XRD, NMR and N2 adsorption measurements and the activity of immobilized glucoamylase for starch hydrolysis was determined in a batch reactor. XRD shows intercalation of enzyme into the clay matrix during both immobilization procedures. Intercalation occurs via the side chains of the amino acid residues, the entire polypeptide backbone being situated at the periphery of the clay matrix. 27Al NMR studies revealed the different nature of interaction of enzyme with the support for both immobilization techniques. N2 adsorption measurements indicated a sharp drop in surface area and pore volume for the covalently bound glucoamylase that suggested severe pore blockage. Activity studies were performed in a batch reactor. The adsorbed and covalently bound glucoamylase retained 49% and 66% activity of the free enzyme respectively. They showed enhanced pH and thermal stabilities. The immobilized enzymes also followed Michaelis–Menten kinetics. Km was greater than the free enzyme that was attributed to an effect of immobilization. The immobilized preparations demonstrated increased reusability as well as storage stability.

Influence of surface and acid properties of vanadia supported on ceria promoted with rice husk silica on cyclohexanol decomposition

Cyclohexanol decomposition activity of supported vanadia catalysts is ascribed to the high surface area, total acidity and interaction between supported vanadia and the amorphous support. Among the supported catalysts, the effect of vanadia over various wt% V2O5 (2–10) loading indicates that the catalyst comprising of 6 wt% V2O5 exhibits higher acidity and decomposition activity. Structural characterization of the catalysts has been done by techniques like energy dispersive X-ray analysis, X-ray diffraction and BET surface area. Acidity of the catalysts has been measured by temperature programmed desorption using ammonia as a probe molecule and the results have been correlated with the activity of catalysts.

Studies on Catalysis by Nano Titania Modified with Metals and Nonmetals

Semiconductor photocatalysis has received much attention during last three decades as a promising solution for both energy generation and environmental problems. Heterogeneous photocatalytic oxidation allows the degradation of organic compounds into carbon dioxide and water in the presence of a semiconductor catalyst and UV light source. The •OH radicals formed during the photocatalytic processes are powerful oxidizing agents and can mineralise a number of organic contaminants. Titanium dioxide (TiO2), due to its chemical stability, non-toxicity and low cost represents one of the most efficient photocatalyst. However, only the ultraviolet fraction of the solar radiation is active in the photoexcitation processes using pure TiO2 and although, TiO2 can treat a wide range of organic pollutants the effectiveness of the process for pollution abatement is still low. A more effective and efficient catalyst therefore must be formulated. Doping of TiO2 was considered with the aim of improving photocatalytic properties. In this study TiO2 catalyst was prepared using the sol-gel method. Metal and nonmetal doped TiO2 catalysts were prepared. The photoactivity of the catalyst was evaluated by the photodegradation of different dyes and pesticides in aqueous solution. High photocatalytic degradation of all the pollutants was observed with doped TiO2. Structural and optical properties of the catalysts were characterized using XRD, BET surface area, UV-Vis. DRS, CHNS analysis, SEM, EDX, TEM, XPS, FTIR and TG. All the catalysts showed the anatase phase. The presence of dopants shifts the absorption of TiO2 into the visible region indicating the possibility of using visible light for photocatalytic processes.

Acid-Base. Surface Electron Donatin6 &.Catai.Ytlc Properties Of Some Binary Mixed Oxides Containing Rare Earth Elements

Catalysis research underpins the science of modern chemical processing and fuel technologies. Catalysis is commercially one of the most important technologies in national economies. Solid state heterogeneous catalyst materials such as metal oxides and metal particles on ceramic oxide substrates are most common. They are typically used with commodity gases and liquid reactants. Selective oxidation catalysts of hydrocarbon feedstocks is the dominant process of converting them to key industrial chemicals, polymers and energy sources.[1] In the absence of a unique successfiil theory of heterogeneous catalysis, attempts are being made to correlate catalytic activity with some specific properties of the solid surface. Such correlations help to narrow down the search for a good catalyst for a given reaction. The heterogeneous catalytic performance of material depends on many factors such as [2] Crystal and surface structure of the catalyst. Thermodynamic stability of the catalyst and the reactant. Acid- base properties of the solid surface. Surface defect properties of the catalyst.Electronic and semiconducting properties and the band structure. Co-existence of dilferent types of ions or structures. Adsorption sites and adsorbed species such as oxygen.Preparation method of catalyst , surface area and nature of heat treatment. Molecular structure of the reactants. Many systematic investigations have been performed to correlate catalytic performances with the above mentioned properties. Many of these investigations remain isolated and further research is needed to bridge the gap in the present knowledge of the field.

Zur Reaktionskinetik der Oxidation von Kohlenstoffmaterialien aus Biomasse

Zur Modellierung von Vergasungs- und Verbrennungsprozessen zur energetischen Nutzung von Biomasse ist die Kenntnis von reaktionskinetischen Daten für die Sauerstoff-Oxidation von Biomassepyrolysaten erforderlich. Eine ausführliche Literaturübersicht zeigt den Stand der Forschung bezüglich der experimentellen Ermittlung von reaktionskinetischen Parametern für die Oxidation von Pyrolysaten aus Lignin, Cellulose und pflanzlicher Biomasse sowie der Suche nach einem plausiblen Reaktionsmechanismus für die Reaktion von Sauerstoff mit festen Kohlenstoffmaterialien. Es wird eine Versuchsanlage mit einem quasistationär betriebenen Differentialreaktor konstruiert, die eine Messung der Reaktionskinetik und der reaktiven inneren Oberfläche (RSA) für die Reaktion eines Pyrolysats aus Maispflanzen mit Sauerstoff ermöglicht. Die getrockneten und zerkleinerten Maispflanzen werden 7 Minuten lang bei 1073 K in einem Drehrohrofen pyrolysiert. Das Pyrolysat zeichnet sich vor allem durch seine hohe Porosität von über 0,9 und seinen hohen Aschegehalt von 0,24 aus. Die RSA wird nach der Methode der Messung von Übergangskinetiken (TK) bestimmt. Die Bestimmung der RSA erfolgt für die Reaktionsprodukte CO und CO2 getrennt, für die entsprechend ermittelten Werte werden die Bezeichnungen CO-RSA und CO2-RSA eingeführt. Die Abhängigkeit dieser Größen von der Sauerstoffkonzentration läßt sich durch eine Langmuir-Isotherme beschreiben, ebenso das leichte Absinken der CO-RSA mit der Kohlendioxidkonzentration. Über dem Abbrand zeigen sich unterschiedliche Verläufe für die CO-RSA, CO2-RSA und die innere Oberfläche nach der BET-Methode. Zur Charakterisierung der Oberflächenzwischenprodukte werden temperaturprogrammierte Desorptionsversuche (TPD) durchgeführt. Die Ergebnisse zeigen, daß eine Unterscheidung in zwei Kohlenstoff-Sauerstoff-Oberflächenkomplexe ausreichend ist. Die experimentellen Untersuchungen zum Oxidationsverlauf werden im kinetisch bestimmten Bereich durchgeführt. Dabei werden die Parameter Temperatur, Sauerstoff-, CO- und CO2-Konzentration variiert. Anhand der Ergebnisse der reaktionskinetischen Untersuchungen wird ein Reaktionsmechanismus für die Kohlenstoff-Sauerstoff-Reaktion entwickelt. Dieser Reaktionsmechanismus umfaßt 7 Elementarreaktionen, für welche die reaktionskinetischen Parameter numerisch ermittelt werden. Darüber hinaus werden reaktionskinetische Parameter für einfachere massenbezogene Reaktionsgeschwindigkeitsansätze berechnet und summarische Reaktionsgeschwindigkeitsansätze für die Bildung von CO und CO2 aus dem Reaktionsmechanismus hergeleitet.

Electrochemical and sonoelectrochemical monitoring of indigo reduction by glucose

The reduction of indigo (dispersed in water) to leuco-indigo (dissolved in water) is an important industrial process and investigated here for the case of glucose as an environmentally benign reducing agent. In order to quantitatively follow the formation of leuco-indigo two approaches based on (i) rotating disk voltammetry and (ii) sonovoltammetry are developed. Leuco-indigo, once formed in alkaline solution, is readily monitored at a glassy carbon electrode in the mass transport limit employing hydrodynamic voltammetry. The presence of power ultrasound further improves the leuco-indigo determination due to additional agitation and homogenization effects. While inactive at room temperature, glucose readily reduces indigo in alkaline media at 65 degrees C. In the presence of excess glucose, a surface dissolution kinetics limited process is proposed following the rate law d eta(leuco-indigo)/dt = k x c(OH-) x S-indigo where eta(leuco-indigo) is the amount of leuco-indigo formed, k = 4.1 x 10(-9) m s(-1) (at 65 degrees C, assuming spherical particles of I gm diameter) is the heterogeneous dissolution rate constant,c(OH-) is the concentration of hydroxide, and Sindigo is the reactive surface area. The activation energy for this process in aqueous 0.2 M NaOH is E-A = 64 U mol(-1) consistent with a considerable temperature effects. The redox mediator 1,8-dihydroxyanthraquinone is shown to significantly enhance the reaction rate by catalysing the electron transfer between glucose and solid indigo particles. (c) 2006 Elsevier Ltd. All fights reserved.

Low-temperature sol-gel preparation of ordered nanoparticles of tungsten carbide/oxide

Tungsten carbide/oxide particles have been prepared by the gel precipitation of tungstic acid in the presence of an organic gelling agent [10% ammonium poly(acrylic acid) in water, supplied by Ciba Specialty Chemicals]. The feed solution; a homogeneous mixture of sodium tungstate and ammonium poly(acrylic acid) in water, was dropped from a 1-mm jet into hydrochloric acid saturated hexanol/concentrated hydrochloric acid to give particles of a mixture of tungstic acid and poly(acrylic acid), which, after drying in air at 100 degrees C and heating to 900 degrees C in argon for 2 h, followed by heating in carbon dioxide for a further 2 h and cooling, gives a mixture of WO, WC, and a trace of NaxWO3, with the carbon for the formation of WC being provided by the thermal carbonization of poly(acrylic acid). The pyrolyzed product is friable and easily broken down in a pestle and mortar to a fine powder or by ultrasonics, in water, to form a stable colloid. The temperature of carbide formation by this process is significantly lower (900 degrees C) than that reported for the commercial preparation of tungsten carbide, typically > 1400 degrees C. In addition, the need for prolonged grinding of the constituents is obviated because the reacting moieties are already in intimate contact on a molecular basis. X-ray diffraction, particle sizing, transmission electron microscopy, surface area, and pore size distribution studies have been carried out, and possible uses are suggested. A flow diagram for the process is described.

Drug interaction and location in liposomes: correlation with polar surface areas

An important step in liposome characterization is to determine the location of a drug within the liposome. This work thus investigated the interaction of dipalmitoylphosphatidylcholine liposomes with drugs of varied water solubility, polar surface area (PSA) and partition coefficient using high sensitivity differential scanning calorimetry. Lipophilic estradiol (ES) interacted strongest with the acyl chains of the lipid membrane, followed by the somewhat polar 5-fluorouracil (5-FU). Strongly hydrophilic mannitol (MAN) showed no evidence of interaction but water soluble polymers inulin (IN) and an antisense oligonucleotide (OLG), which have very high PSAs, interacted with the lipid head groups. Accordingly, the drugs could be classified as: hydrophilic ones situated in the aqueous core and which may interact with the head groups; those located at the water-bilayer interface with some degree of penetration into the lipid bilayer; those lipophilic drugs constrained within the bilayer. (c) 2004 Elsevier B.V. All rights reserved.