Centrifuge Modeling of Sandy Slopes

Slope failure occurs in many areas throughout the world and it becomes an important problem when it interferes with human activity, in which disasters provoke loss of life and property damage. In this research we investigate the slope failure through the centrifuge modeling, where a reduced-scale model, N times smaller than the full-scale (prototype), is used whereas the acceleration is increased by N times (compared with the gravity acceleration) to preserve the stress and the strain behavior. The aims of this research “Centrifuge modeling of sandy slopes” are in extreme synthesis: 1) test the reliability of the centrifuge modeling as a tool to investigate the behavior of a sandy slope failure; 2) understand how the failure mechanism is affected by changing the slope angle and obtain useful information for the design. In order to achieve this scope we arranged the work as follows: Chapter one: centrifuge modeling of slope failure. In this chapter we provide a general view about the context in which we are working on. Basically we explain what is a slope failure, how it happens and which are the tools available to investigate this phenomenon. Afterwards we introduce the technology used to study this topic, that is the geotechnical centrifuge. Chapter two: testing apparatus. In the first section of this chapter we describe all the procedures and facilities used to perform a test in the centrifuge. Then we explain the characteristics of the soil (Nevada sand), like the dry unit weight, water content, relative density, and its strength parameters (c,φ), which have been calculated in laboratory through the triaxial test. Chapter three: centrifuge tests. In this part of the document are presented all the results from the tests done in centrifuge. When we talk about results we refer to the acceleration at failure for each model tested and its failure surface. In our case study we tested models with the same soil and geometric characteristics but different angles. The angles tested in this research were: 60°, 75° and 90°. Chapter four: slope stability analysis. We introduce the features and the concept of the software: ReSSA (2.0). This software allows us to calculate the theoretical failure surfaces of the prototypes. Then we show in this section the comparisons between the experimental failure surfaces of the prototype, traced in the laboratory, and the one calculated by the software. Chapter five: conclusion. The conclusion of the research presents the results obtained in relation to the two main aims, mentioned above.

Il passato nell’epoca della sua (ri)producibilità digitale. Torino 1943 - 45. Metodologia della ricerca con tecnologie informatiche. Sistema storico-territoriale di informazione multimediale

Se il lavoro dello storico è capire il passato come è stato compreso dalla gente che lo ha vissuto, allora forse non è azzardato pensare che sia anche necessario comunicare i risultati delle ricerche con strumenti propri che appartengono a un'epoca e che influenzano la mentalità di chi in quell'epoca vive. Emergenti tecnologie, specialmente nell’area della multimedialità come la realtà virtuale, permettono agli storici di comunicare l’esperienza del passato in più sensi. In che modo la storia collabora con le tecnologie informatiche soffermandosi sulla possibilità di fare ricostruzioni storiche virtuali, con relativi esempi e recensioni? Quello che maggiormente preoccupa gli storici è se una ricostruzione di un fatto passato vissuto attraverso la sua ricreazione in pixels sia un metodo di conoscenza della storia che possa essere considerato valido. Ovvero l'emozione che la navigazione in una realtà 3D può suscitare, è un mezzo in grado di trasmettere conoscenza? O forse l'idea che abbiamo del passato e del suo studio viene sottilmente cambiato nel momento in cui lo si divulga attraverso la grafica 3D? Da tempo però la disciplina ha cominciato a fare i conti con questa situazione, costretta soprattutto dall'invasività di questo tipo di media, dalla spettacolarizzazione del passato e da una divulgazione del passato parziale e antiscientifica. In un mondo post letterario bisogna cominciare a pensare che la cultura visuale nella quale siamo immersi sta cambiando il nostro rapporto con il passato: non per questo le conoscenze maturate fino ad oggi sono false, ma è necessario riconoscere che esiste più di una verità storica, a volte scritta a volte visuale. Il computer è diventato una piattaforma onnipresente per la rappresentazione e diffusione dell’informazione. I metodi di interazione e rappresentazione stanno evolvendo di continuo. Ed è su questi due binari che è si muove l’offerta delle tecnologie informatiche al servizio della storia. Lo scopo di questa tesi è proprio quello di esplorare, attraverso l’utilizzo e la sperimentazione di diversi strumenti e tecnologie informatiche, come si può raccontare efficacemente il passato attraverso oggetti tridimensionali e gli ambienti virtuali, e come, nel loro essere elementi caratterizzanti di comunicazione, in che modo possono collaborare, in questo caso particolare, con la disciplina storica. La presente ricerca ricostruisce alcune linee di storia delle principali fabbriche attive a Torino durante la seconda guerra mondiale, ricordando stretta relazione che esiste tra strutture ed individui e in questa città in particolare tra fabbrica e movimento operaio, è inevitabile addentrarsi nelle vicende del movimento operaio torinese che nel periodo della lotta di Liberazione in città fu un soggetto politico e sociale di primo rilievo. Nella città, intesa come entità biologica coinvolta nella guerra, la fabbrica (o le fabbriche) diventa il nucleo concettuale attraverso il quale leggere la città: sono le fabbriche gli obiettivi principali dei bombardamenti ed è nelle fabbriche che si combatte una guerra di liberazione tra classe operaia e autorità, di fabbrica e cittadine. La fabbrica diventa il luogo di "usurpazione del potere" di cui parla Weber, il palcoscenico in cui si tengono i diversi episodi della guerra: scioperi, deportazioni, occupazioni .... Il modello della città qui rappresentata non è una semplice visualizzazione ma un sistema informativo dove la realtà modellata è rappresentata da oggetti, che fanno da teatro allo svolgimento di avvenimenti con una precisa collocazione cronologica, al cui interno è possibile effettuare operazioni di selezione di render statici (immagini), di filmati precalcolati (animazioni) e di scenari navigabili interattivamente oltre ad attività di ricerca di fonti bibliografiche e commenti di studiosi segnatamente legati all'evento in oggetto. Obiettivo di questo lavoro è far interagire, attraverso diversi progetti, le discipline storiche e l’informatica, nelle diverse opportunità tecnologiche che questa presenta. Le possibilità di ricostruzione offerte dal 3D vengono così messe a servizio della ricerca, offrendo una visione integrale in grado di avvicinarci alla realtà dell’epoca presa in considerazione e convogliando in un’unica piattaforma espositiva tutti i risultati. Divulgazione Progetto Mappa Informativa Multimediale Torino 1945 Sul piano pratico il progetto prevede una interfaccia navigabile (tecnologia Flash) che rappresenti la pianta della città dell’epoca, attraverso la quale sia possibile avere una visione dei luoghi e dei tempi in cui la Liberazione prese forma, sia a livello concettuale, sia a livello pratico. Questo intreccio di coordinate nello spazio e nel tempo non solo migliora la comprensione dei fenomeni, ma crea un maggiore interesse sull’argomento attraverso l’utilizzo di strumenti divulgativi di grande efficacia (e appeal) senza perdere di vista la necessità di valicare le tesi storiche proponendosi come piattaforma didattica. Un tale contesto richiede uno studio approfondito degli eventi storici al fine di ricostruire con chiarezza una mappa della città che sia precisa sia topograficamente sia a livello di navigazione multimediale. La preparazione della cartina deve seguire gli standard del momento, perciò le soluzioni informatiche utilizzate sono quelle fornite da Adobe Illustrator per la realizzazione della topografia, e da Macromedia Flash per la creazione di un’interfaccia di navigazione. La base dei dati descrittivi è ovviamente consultabile essendo contenuta nel supporto media e totalmente annotata nella bibliografia. È il continuo evolvere delle tecnologie d'informazione e la massiccia diffusione dell’uso dei computer che ci porta a un cambiamento sostanziale nello studio e nell’apprendimento storico; le strutture accademiche e gli operatori economici hanno fatto propria la richiesta che giunge dall'utenza (insegnanti, studenti, operatori dei Beni Culturali) di una maggiore diffusione della conoscenza storica attraverso la sua rappresentazione informatizzata. Sul fronte didattico la ricostruzione di una realtà storica attraverso strumenti informatici consente anche ai non-storici di toccare con mano quelle che sono le problematiche della ricerca quali fonti mancanti, buchi della cronologia e valutazione della veridicità dei fatti attraverso prove. Le tecnologie informatiche permettono una visione completa, unitaria ed esauriente del passato, convogliando tutte le informazioni su un'unica piattaforma, permettendo anche a chi non è specializzato di comprendere immediatamente di cosa si parla. Il miglior libro di storia, per sua natura, non può farlo in quanto divide e organizza le notizie in modo diverso. In questo modo agli studenti viene data l'opportunità di apprendere tramite una rappresentazione diversa rispetto a quelle a cui sono abituati. La premessa centrale del progetto è che i risultati nell'apprendimento degli studenti possono essere migliorati se un concetto o un contenuto viene comunicato attraverso più canali di espressione, nel nostro caso attraverso un testo, immagini e un oggetto multimediale. Didattica La Conceria Fiorio è uno dei luoghi-simbolo della Resistenza torinese. Il progetto è una ricostruzione in realtà virtuale della Conceria Fiorio di Torino. La ricostruzione serve a arricchire la cultura storica sia a chi la produce, attraverso una ricerca accurata delle fonti, sia a chi può poi usufruirne, soprattutto i giovani, che, attratti dall’aspetto ludico della ricostruzione, apprendono con più facilità. La costruzione di un manufatto in 3D fornisce agli studenti le basi per riconoscere ed esprimere la giusta relazione fra il modello e l’oggetto storico. Le fasi di lavoro attraverso cui si è giunti alla ricostruzione in 3D della Conceria: . una ricerca storica approfondita, basata sulle fonti, che possono essere documenti degli archivi o scavi archeologici, fonti iconografiche, cartografiche, ecc.; . La modellazione degli edifici sulla base delle ricerche storiche, per fornire la struttura geometrica poligonale che permetta la navigazione tridimensionale; . La realizzazione, attraverso gli strumenti della computer graphic della navigazione in 3D. Unreal Technology è il nome dato al motore grafico utilizzato in numerosi videogiochi commerciali. Una delle caratteristiche fondamentali di tale prodotto è quella di avere uno strumento chiamato Unreal editor con cui è possibile costruire mondi virtuali, e che è quello utilizzato per questo progetto. UnrealEd (Ued) è il software per creare livelli per Unreal e i giochi basati sul motore di Unreal. E’ stata utilizzata la versione gratuita dell’editor. Il risultato finale del progetto è un ambiente virtuale navigabile raffigurante una ricostruzione accurata della Conceria Fiorio ai tempi della Resistenza. L’utente può visitare l’edificio e visualizzare informazioni specifiche su alcuni punti di interesse. La navigazione viene effettuata in prima persona, un processo di “spettacolarizzazione” degli ambienti visitati attraverso un arredamento consono permette all'utente una maggiore immersività rendendo l’ambiente più credibile e immediatamente codificabile. L’architettura Unreal Technology ha permesso di ottenere un buon risultato in un tempo brevissimo, senza che fossero necessari interventi di programmazione. Questo motore è, quindi, particolarmente adatto alla realizzazione rapida di prototipi di una discreta qualità, La presenza di un certo numero di bug lo rende, però, in parte inaffidabile. Utilizzare un editor da videogame per questa ricostruzione auspica la possibilità di un suo impiego nella didattica, quello che le simulazioni in 3D permettono nel caso specifico è di permettere agli studenti di sperimentare il lavoro della ricostruzione storica, con tutti i problemi che lo storico deve affrontare nel ricreare il passato. Questo lavoro vuole essere per gli storici una esperienza nella direzione della creazione di un repertorio espressivo più ampio, che includa gli ambienti tridimensionali. Il rischio di impiegare del tempo per imparare come funziona questa tecnologia per generare spazi virtuali rende scettici quanti si impegnano nell'insegnamento, ma le esperienze di progetti sviluppati, soprattutto all’estero, servono a capire che sono un buon investimento. Il fatto che una software house, che crea un videogame di grande successo di pubblico, includa nel suo prodotto, una serie di strumenti che consentano all'utente la creazione di mondi propri in cui giocare, è sintomatico che l'alfabetizzazione informatica degli utenti medi sta crescendo sempre più rapidamente e che l'utilizzo di un editor come Unreal Engine sarà in futuro una attività alla portata di un pubblico sempre più vasto. Questo ci mette nelle condizioni di progettare moduli di insegnamento più immersivi, in cui l'esperienza della ricerca e della ricostruzione del passato si intreccino con lo studio più tradizionale degli avvenimenti di una certa epoca. I mondi virtuali interattivi vengono spesso definiti come la forma culturale chiave del XXI secolo, come il cinema lo è stato per il XX. Lo scopo di questo lavoro è stato quello di suggerire che vi sono grosse opportunità per gli storici impiegando gli oggetti e le ambientazioni in 3D, e che essi devono coglierle. Si consideri il fatto che l’estetica abbia un effetto sull’epistemologia. O almeno sulla forma che i risultati delle ricerche storiche assumono nel momento in cui devono essere diffuse. Un’analisi storica fatta in maniera superficiale o con presupposti errati può comunque essere diffusa e avere credito in numerosi ambienti se diffusa con mezzi accattivanti e moderni. Ecco perchè non conviene seppellire un buon lavoro in qualche biblioteca, in attesa che qualcuno lo scopra. Ecco perchè gli storici non devono ignorare il 3D. La nostra capacità, come studiosi e studenti, di percepire idee ed orientamenti importanti dipende spesso dai metodi che impieghiamo per rappresentare i dati e l’evidenza. Perché gli storici possano ottenere il beneficio che il 3D porta con sè, tuttavia, devono sviluppare un’agenda di ricerca volta ad accertarsi che il 3D sostenga i loro obiettivi di ricercatori e insegnanti. Una ricostruzione storica può essere molto utile dal punto di vista educativo non sono da chi la visita ma, anche da chi la realizza. La fase di ricerca necessaria per la ricostruzione non può fare altro che aumentare il background culturale dello sviluppatore. Conclusioni La cosa più importante è stata la possibilità di fare esperienze nell’uso di mezzi di comunicazione di questo genere per raccontare e far conoscere il passato. Rovesciando il paradigma conoscitivo che avevo appreso negli studi umanistici, ho cercato di desumere quelle che potremo chiamare “leggi universali” dai dati oggettivi emersi da questi esperimenti. Da punto di vista epistemologico l’informatica, con la sua capacità di gestire masse impressionanti di dati, dà agli studiosi la possibilità di formulare delle ipotesi e poi accertarle o smentirle tramite ricostruzioni e simulazioni. Il mio lavoro è andato in questa direzione, cercando conoscere e usare strumenti attuali che nel futuro avranno sempre maggiore presenza nella comunicazione (anche scientifica) e che sono i mezzi di comunicazione d’eccellenza per determinate fasce d’età (adolescenti). Volendo spingere all’estremo i termini possiamo dire che la sfida che oggi la cultura visuale pone ai metodi tradizionali del fare storia è la stessa che Erodoto e Tucidide contrapposero ai narratori di miti e leggende. Prima di Erodoto esisteva il mito, che era un mezzo perfettamente adeguato per raccontare e dare significato al passato di una tribù o di una città. In un mondo post letterario la nostra conoscenza del passato sta sottilmente mutando nel momento in cui lo vediamo rappresentato da pixel o quando le informazioni scaturiscono non da sole, ma grazie all’interattività con il mezzo. La nostra capacità come studiosi e studenti di percepire idee ed orientamenti importanti dipende spesso dai metodi che impieghiamo per rappresentare i dati e l’evidenza. Perché gli storici possano ottenere il beneficio sottinteso al 3D, tuttavia, devono sviluppare un’agenda di ricerca volta ad accertarsi che il 3D sostenga i loro obiettivi di ricercatori e insegnanti. Le esperienze raccolte nelle pagine precedenti ci portano a pensare che in un futuro non troppo lontano uno strumento come il computer sarà l’unico mezzo attraverso cui trasmettere conoscenze, e dal punto di vista didattico la sua interattività consente coinvolgimento negli studenti come nessun altro mezzo di comunicazione moderno.

Spectrum shaping and its application: spread-spectrum clock generator and circuits for ultra wide band

Electromagnetic spectrum can be identified as a resource for the designer, as well as for the manufacturer, from two complementary points of view: first, because it is a good in great demand by many different kind of applications; second, because despite its scarce availability, it may be advantageous to use more spectrum than necessary. This is the case of Spread-Spectrum Systems, those systems in which the transmitted signal is spread over a wide frequency band, much wider, in fact, than the minimum bandwidth required to transmit the information being sent. Part I of this dissertation deals with Spread-Spectrum Clock Generators (SSCG) aiming at reducing Electro Magnetic Interference (EMI) of clock signals in integrated circuits (IC) design. In particular, the modulation of the clock and the consequent spreading of its spectrum are obtained through a random modulating signal outputted by a chaotic map, i.e. a discrete-time dynamical system showing chaotic behavior. The advantages offered by this kind of modulation are highlighted. Three different prototypes of chaos-based SSCG are presented in all their aspects: design, simulation, and post-fabrication measurements. The third one, operating at a frequency equal to 3GHz, aims at being applied to Serial ATA, standard de facto for fast data transmission to and from Hard Disk Drives. The most extreme example of spread-spectrum signalling is the emerging ultra-wideband (UWB) technology, which proposes the use of large sections of the radio spectrum at low amplitudes to transmit high-bandwidth digital data. In part II of the dissertation, two UWB applications are presented, both dealing with the advantages as well as with the challenges of a wide-band system, namely: a chaos-based sequence generation method for reducing Multiple Access Interference (MAI) in Direct Sequence UWB Wireless-Sensor-Networks (WSNs), and design and simulations of a Low-Noise Amplifier (LNA) for impulse radio UWB. This latter topic was studied during a study-abroad period in collaboration with Delft University of Technology, Delft, Netherlands.

Monte Carlo Simulations of Novel Scintillator Detectors and Dosimetry Calculations

Monte Carlo (MC) simulation techniques are becoming very common in the Medical Physicists community. MC can be used for modeling Single Photon Emission Computed Tomography (SPECT) and for dosimetry calculations. 188Re, is a promising candidate for radiotherapeutic production and understanding the mechanisms of the radioresponse of tumor cells "in vitro" is of crucial importance as a first step before "in vivo" studies. The dosimetry of 188Re, used to target different lines of cancer cells, has been evaluated by the MC code GEANT4. The simulations estimate the average energy deposition/per event in the biological samples. The development of prototypes for medical imaging, based on LaBr3:Ce scintillation crystals coupled with a position sensitive photomultiplier, have been studied using GEANT4 simulations. Having tested, in the simulation, surface treatments different from the one applied to the crystal used in our experimental measurements, we found out that the Energy Resolution (ER) and the Spatial Resolution (SR) could be improved, in principle, by machining in a different way the lateral surfaces of the crystal. We have then studied a system able to acquire both echographic and scintigraphic images to let the medical operator obtain the complete anatomic and functional information for tumor diagnosis. The scintigraphic part of the detector is simulated by GEANT4 and first attempts to reconstruct tomographic images have been made using as method of reconstruction a back-projection standard algorithm. The proposed camera is based on slant collimators and LaBr3:Ce crystals. Within the Field of View (FOV) of the camera, it possible to distinguish point sources located in air at a distance of about 2 cm from each other. In particular conditions of uptake, tumor depth and dimension, the preliminary results show that the Signal to Noise Ratio (SNR) values obtained are higher than the standard detection limit.

Body ares networks for human motor assessment

Healthcare, Human Computer Interfaces (HCI), Security and Biometry are the most promising application scenario directly involved in the Body Area Networks (BANs) evolution. Both wearable devices and sensors directly integrated in garments envision a word in which each of us is supervised by an invisible assistant monitoring our health and daily-life activities. New opportunities are enabled because improvements in sensors miniaturization and transmission efficiency of the wireless protocols, that achieved the integration of high computational power aboard independent, energy-autonomous, small form factor devices. Application’s purposes are various: (I) data collection to achieve off-line knowledge discovery; (II) user notification of his/her activities or in case a danger occurs; (III) biofeedback rehabilitation; (IV) remote alarm activation in case the subject need assistance; (V) introduction of a more natural interaction with the surrounding computerized environment; (VI) users identification by physiological or behavioral characteristics. Telemedicine and mHealth [1] are two of the leading concepts directly related to healthcare. The capability to borne unobtrusiveness objects supports users’ autonomy. A new sense of freedom is shown to the user, not only supported by a psychological help but a real safety improvement. Furthermore, medical community aims the introduction of new devices to innovate patient treatments. In particular, the extension of the ambulatory analysis in the real life scenario by proving continuous acquisition. The wide diffusion of emerging wellness portable equipment extended the usability of wearable devices also for fitness and training by monitoring user performance on the working task. The learning of the right execution techniques related to work, sport, music can be supported by an electronic trainer furnishing the adequate aid. HCIs made real the concept of Ubiquitous, Pervasive Computing and Calm Technology introduced in the 1988 by Marc Weiser and John Seeley Brown. They promotes the creation of pervasive environments, enhancing the human experience. Context aware, adaptive and proactive environments serve and help people by becoming sensitive and reactive to their presence, since electronics is ubiquitous and deployed everywhere. In this thesis we pay attention to the integration of all the aspects involved in a BAN development. Starting from the choice of sensors we design the node, configure the radio network, implement real-time data analysis and provide a feedback to the user. We present algorithms to be implemented in wearable assistant for posture and gait analysis and to provide assistance on different walking conditions, preventing falls. Our aim, expressed by the idea to contribute at the development of a non proprietary solutions, driven us to integrate commercial and standard solutions in our devices. We use sensors available on the market and avoided to design specialized sensors in ASIC technologies. We employ standard radio protocol and open source projects when it was achieved. The specific contributions of the PhD research activities are presented and discussed in the following. • We have designed and build several wireless sensor node providing both sensing and actuator capability making the focus on the flexibility, small form factor and low power consumption. The key idea was to develop a simple and general purpose architecture for rapid analysis, prototyping and deployment of BAN solutions. Two different sensing units are integrated: kinematic (3D accelerometer and 3D gyroscopes) and kinetic (foot-floor contact pressure forces). Two kind of feedbacks were implemented: audio and vibrotactile. • Since the system built is a suitable platform for testing and measuring the features and the constraints of a sensor network (radio communication, network protocols, power consumption and autonomy), we made a comparison between Bluetooth and ZigBee performance in terms of throughput and energy efficiency. Test in the field evaluate the usability in the fall detection scenario. • To prove the flexibility of the architecture designed, we have implemented a wearable system for human posture rehabilitation. The application was developed in conjunction with biomedical engineers who provided the audio-algorithms to furnish a biofeedback to the user about his/her stability. • We explored off-line gait analysis of collected data, developing an algorithm to detect foot inclination in the sagittal plane, during walk. • In collaboration with the Wearable Lab – ETH, Zurich, we developed an algorithm to monitor the user during several walking condition where the user carry a load. The remainder of the thesis is organized as follows. Chapter I gives an overview about Body Area Networks (BANs), illustrating the relevant features of this technology and the key challenges still open. It concludes with a short list of the real solutions and prototypes proposed by academic research and manufacturers. The domain of the posture and gait analysis, the methodologies, and the technologies used to provide real-time feedback on detected events, are illustrated in Chapter II. The Chapter III and IV, respectively, shown BANs developed with the purpose to detect fall and monitor the gait taking advantage by two inertial measurement unit and baropodometric insoles. Chapter V reports an audio-biofeedback system to improve balance on the information provided by the use centre of mass. A walking assistant based on the KNN classifier to detect walking alteration on load carriage, is described in Chapter VI.

Electrode Materials for Ionic Liquid Based-Supercapacitors

The development of safe, high energy and power electrochemical energy-conversion systems can be a response to the worldwide demand for a clean and low-fuel-consuming transport. This thesis work, starting from a basic studies on the ionic liquid (IL) electrolytes and carbon electrodes and concluding with tests on large-size IL-based supercapacitor prototypes demonstrated that the IL-based asymmetric configuration (AEDLCs) is a powerful strategy to develop safe, high-energy supercapacitors that might compete with lithium-ion batteries in power assist-hybrid electric vehicles (HEVs). The increase of specific energy in EDLCs was achieved following three routes: i) the use of hydrophobic ionic liquids (ILs) as electrolytes; ii) the design and preparation of carbon electrode materials of tailored morphology and surface chemistry to feature high capacitance response in IL and iii) the asymmetric double-layer carbon supercapacitor configuration (AEDLC) which consists of assembling the supercapacitor with different carbon loadings at the two electrodes in order to exploit the wide electrochemical stability window (ESW) of IL and to reach high maximum cell voltage (Vmax). Among the various ILs investigated the N-methoxyethyl-N-methylpyrrolidinium bis(trifluoromethanesulfonyl)imide (PYR1(2O1)TFSI) was selected because of its hydrophobicity and high thermal stability up to 350 °C together with good conductivity and wide ESW, exploitable in a wide temperature range, below 0°C. For such exceptional properties PYR1(2O1)TFSI was used for the whole study to develop large size IL-based carbon supercapacitor prototype. This work also highlights that the use of ILs determines different chemical-physical properties at the interface electrode/electrolyte with respect to that formed by conventional electrolytes. Indeed, the absence of solvent in ILs makes the properties of the interface not mediated by the solvent and, thus, the dielectric constant and double-layer thickness strictly depend on the chemistry of the IL ions. The study of carbon electrode materials evidences several factors that have to be taken into account for designing performing carbon electrodes in IL. The heat-treatment in inert atmosphere of the activated carbon AC which gave ACT carbon featuring ca. 100 F/g in IL demonstrated the importance of surface chemistry in the capacitive response of the carbons in hydrophobic ILs. The tailored mesoporosity of the xerogel carbons is a key parameter to achieve high capacitance response. The CO2-treated xerogel carbon X3a featured a high specific capacitance of 120 F/g in PYR14TFSI, however, exhibiting high pore volume, an excess of IL is required to fill the pores with respect to that necessary for the charge-discharge process. Further advances were achieved with electrodes based on the disordered template carbon DTC7 with pore size distribution centred at 2.7 nm which featured a notably high specific capacitance of 140 F/g in PYR14TFSI and a moderate pore volume, V>1.5 nm of 0.70 cm3/g. This thesis work demonstrated that by means of the asymmetric configuration (AEDLC) it was possible to reach high cell voltage up to 3.9 V. Indeed, IL-based AEDLCs with the X3a or ACT carbon electrodes exhibited specific energy and power of ca. 30 Wh/kg and 10 kW/kg, respectively. The DTC7 carbon electrodes, featuring a capacitance response higher of 20%-40% than those of X3a and ACT, respectively, enabled the development of a PYR14TFSI-based AEDLC with specific energy and power of 47 Wh/kg and 13 kW/kg at 60°C with Vmax of 3.9 V. Given the availability of the ACT carbon (obtained from a commercial material), the PYR1(2O1)TFSI-based AEDLCs assembled with ACT carbon electrodes were selected within the EU ILHYPOS project for the development of large-size prototypes. This study demonstrated that PYR1(2O1)TFSI-based AEDLC can operate between -30°C and +60°C and its cycling stability was proved at 60°C up to 27,000 cycles with high Vmax up to 3.8 V. Such AEDLC was further investigated following USABC and DOE FreedomCAR reference protocols for HEV to evaluate its dynamic pulse-power and energy features. It was demonstrated that with Vmax of 3.7 V at T> 30 °C the challenging energy and power targets stated by DOE for power-assist HEVs, and at T> 0 °C the standards for the 12V-TSS and 42V-FSS and TPA 2s-pulse applications are satisfied, if the ratio wmodule/wSC = 2 is accomplished, which, however, is a very demanding condition. Finally, suggestions for further advances in IL-based AEDLC performance were found. Particularly, given that the main contribution to the ESR is the electrode charging resistance, which in turn is affected by the ionic resistance in the pores that is also modulated by pore length, the pore geometry is a key parameter in carbon design not only because it defines the carbon surface but also because it can differentially “amplify” the effect of IL conductivity on the electrode charging-discharging process and, thus, supercapacitor time constant.

Optical Microring Resonators based on ion-implanted LiNbO3 ridge waveguides

The growing interest for Integrated Optics for sensing, telecommunications and even electronics is driving research to find solutions to the new challenges issued by a more and more fast, connected and smart world. This thesis deals with the design, the fabrication and the characterisation of the first prototypes of Microring Resonators realised using ion implanted Lithium Niobate (LiNbO3) ridge waveguides. Optical Resonator is one among the most important devices for all tasks described above. LiNbO3 is the substrate commonly used to fabricate optical modulators thanks to its electro-optic characteristics. Since it is produced in high quantity, good quality and large wafers its price is low compared to other electro-optic substrate. We propose to use ion implantation as fabrication technology because in the other way standard optical waveguides realised in LiNbO3 by Proton Exchange (PE) or metal diffusion do not allow small bending radii, which are necessary to keep the circuit footprint small. We will show in fact that this approach allows to fabricate waveguides on Lithium Niobate that are better than PE or metal diffused waveguides as it allows smaller size devices and tailoring of the refractive index profile controlling the implantation parameters. Moreover, we will show that the ridge technology based on enhanced etching rate via ion implantation produces a waveguide with roughness lower than a dry etched one. Finally it has been assessed a complete technological process for fabrication of Microring Resonator devices in Lithium Niobate by ion implantation and the first prototypes have been produced.

Stereoselektive Synthese von Stickstoffheterocyclen an Glycosylaminen als chiralen Auxiliaren

Alkaloide, im allgemeinen Stickstoffheterocyclen, sind wichtige Vorläuferverbindungen von pharmakologisch aktiven Substanzen. Die stereoselektive Synthese von Stickstoffheterocyclen ist von großem Interesse für die Entdeckung und Entwicklung von Arzneistoffen.In der Arbeit wurden Glycosylamine vom Typ des 2,3,4,6-Tetra-O-pivaloyl-?-D-galactosylamins bzw. des 2,3,4-Tri-O-pivaloyl-?-D-arabinosylamins zur diastereoselektiven Synthese mehrfach substituierter Stickstoffheterocyclen eingesetzt. In einer Tandem-Mannich-Michael-Reaktion eines Glycosylimins mit dem Danishefsky-Dien wurden die in Position 6 substituierten Dehydropiperidinone aufgebaut. In einer mehrstufigen Synthesesequenz konnte das 4a-Epimere des natürlichen Pumiliotoxin C als Hydrochlorid dargestellt werden.Mittels der Tandem-Mannich-Michael-Reaktion wurden auch 6,6`-disubstituierte Dehydropiperidinone dargestellt. Die Darstellung zweier Aza-spiro-Verbindungen gelang erstmals ausgehend von den Ketonen Cyclohexanon und 3-Methyl-cyclohexanon über die Glycosylketimine. Das in dieser Reaktion gefundene Nebenprodukt N-Glycosyl-6-(2´-oxo-propyl)-2,3 dehydropiperidin-4-on diente als Ausgangssubstanz für die Pinidinolsynthese.In der angewendeten Weise eignen sich Glycosylamine sehr gut für die stereoselektive Synthese von Stickstoffheterocyclen. Meistens werden die chirale Piperidinalkaloidvorläufer in hohen Ausbeuten und Diastereoselektivitäten erhalten.

Weiterentwicklung einer Produktionsanlage und der Speicherungs- bzw. Transportkonzepte für hochpolarisiertes 3He

Der Bedarf an hyperpolarisiertem 3He in Medizin und physikalischer Grundlagenforschung ist in den letzten ca. 10-15 Jahren sowohl in Bezug auf die zu Verfügung stehende Menge, als auch auf den benötigten Grad der Kernspinpolarisation stetig gestiegen. Gleichzeitig mußten Lösungen für die polarisationserhaltende Speicherung und den Transport gefunden werden, die je nach Anwendung anzupassen waren. Als Ergebnis kann mit dieser Arbeit ein in sich geschlossenes Gesamtkonzept vorgestellt werden, daß sowohl die entsprechenden Mengen für klinische Anwendungen, als auch höchste Polarisation für physikalische Grundlagenfor-schung zur Verfügung stellen kann. Verschiedene unabhängige Polarimetriemethoden zeigten in sich konsistente Ergebnisse und konnten, neben ihrer eigenen Weiterentwicklung, zu einer verläßlichen Charakterisierung des neuen Systems und auch der Transportzellen und –boxen eingesetzt werden. Die Polarisation wird mittels „Metastabilem Optischen Pumpen“ bei einem Druck von 1 mbar erzeugt. Dabei werden ohne Gasfluß Werte von P = 84% erreicht. Im Flußbetrieb sinkt die erreichbare Polarisation auf P ≈ 77%. Das 3He kann dann weitgehend ohne Polarisationsver-luste auf mehrere bar komprimiert und zu den jeweiligen Experimenten transportiert werden. Durch konsequente Weiterentwicklung der vorgestellten Polarisationseinheit an fast allen Komponenten kann somit jetzt bei einem Fluß von 0,8 barl/h eine Polarisation von Pmax = 77% am Auslaß der Apparatur erreicht werden. Diese skaliert linear mit dem Fluß, sodaß bei 3 barl/h die Polarisation immer noch bei ca. 60% liegt. Dabei waren die im Rahmen dieser Arbeit durchgeführten Verbesserungen an den Lasern, der Optik, der Kompressionseinheit, dem Zwischenspeicher und der Gasreinigung wesentlich für das Erreichen dieser Polarisatio-nen. Neben dem Einsatz eines neuen Faserlasersystems ist die hohe Gasreinheit und die lang-lebige Kompressionseinheit ein Schlüssel für diese Leistungsfähigkeit. Seit Herbst 2001 er-zeugte das System bereits über 2000 barl hochpolarisiertes 3He und ermöglichte damit zahl-reiche interdisziplinäre Experimente und Untersuchungen. Durch Verbesserungen an als Prototypen bereits vorhandenen Transportboxen und durch weitgehende Unterdrückung der Wandrelaxation in den Transportgefäßen aufgrund neuer Erkenntnisse über deren Ursachen stellen auch polarisationserhaltende Transporte über große Strecken kein Problem mehr dar. In unbeschichteten 1 Liter Kolben aus Aluminosilikatglä-sern werden nun problemlos Speicherzeiten von T1 > 200h erreicht. Im Rahmen des europäi-schen Forschungsprojektes „Polarized Helium to Image the Lung“ wurden während 19 Liefe-rungen 70barl 3He nach Sheffield (UK) und bei 13 Transporten 100 barl nach Kopenhagen (DK) per Flugzeug transportiert. Zusammenfassend konnte gezeigt werden, daß die Problematik der Kernspinpolarisationser-zeugung von 3He, die Speicherung, der Transport und die Verwendung des polarisierten Ga-ses in klinischer Diagnostik und physikalischen Grundlagenexperimenten weitgehend gelöst ist und das Gesamtkonzept die Voraussetzungen für allgemeine Anwendungen auf diesen Gebieten geschaffen hat.

Design and fabrication of MOMS-based ultrasonic probes for minimally invasive endoscopic applications

A Micro-opto-mechanical systems (MOMS) based technology for the fabrication of ultrasonic probes on optical fiber is presented. Thanks to the high miniaturization level reached, the realization of an ultrasonic system constituted by ultrasonic generating and detecting elements, suitable for minimally invasive applications or Non Destructive Evaluation (NDE) of materials at high resolution, is demonstrated. The ultrasonic generation is realized by irradiating a highly absorbing carbon film patterned on silicon micromachined structures with a nanosecond pulsed laser source, generating a mechanical shock wave due to the thermal expansion of the film induced by optical energy conversion into heat. The short duration of the pulsed laser, together with an appropriate emitter design, assure high frequency and wide band ultrasonic generation. The acoustic detection is also realized on a MOMS device using an interferometric receiver, fabricated with a Fabry-Perot optical cavity realized by means of a patterned SU-8 and two Al metallization levels. In order to detect the ultrasonic waves, the cavity is interrogated by a laser beam measuring the reflected power with a photodiode. Various issues related to the design and fabrication of these acoustic probes are investigated in this thesis. First, theoretical models are developed to characterize the opto-acoustic behavior of the devices and estimate their expected acoustic performances. Tests structures are realized to derive the relevant physical parameters of the materials constituting the MOMS devices and determine the conditions theoretically assuring the best acoustic emission and detection performances. Moreover, by exploiting the models and the theoretical results, prototypes of acoustic probes are designed and their fabrication process developed by means of an extended experimental activity.

Functional photoactive and electroactive nanodevices

Most of current ultra-miniaturized devices are obtained by the top-down approach, in which nanoscale components are fabricated by cutting down larger precursors. Since this physical-engineering method is reaching its limits, especially for components below 30 nm in size, alternative strategies are necessary. Of particular appeal to chemists is the supramolecular bottom-up approach to nanotechnology, a methodology that utilizes the principles of molecular recognition to build materials and devices from molecular components. The subject of this thesis is the photophysical and electrochemical investigation of nanodevices obtained harnessing the principles of supramolecular chemistry. These systems operate in solution-based environments and are investigated at the ensemble level. The majority of the chemical systems discussed here are based on pseudorotaxanes and catenanes. Such supramolecular systems represent prototypes of molecular machines since they are capable of performing simple controlled mechanical movements. Their properties and operation are strictly related to the supramolecular interactions between molecular components (generally photoactive or electroactive molecules) and to the possibility of modulating such interactions by means of external stimuli. The main issues addressed throughout the thesis are: (i) the analysis of the factors that can affect the architecture and perturb the stability of supramolecular systems; (ii) the possibility of controlling the direction of supramolecular motions exploiting the molecular information content; (iii) the development of switchable supramolecular polymers starting from simple host-guest complexes; (iv) the capability of some molecular machines to process information at molecular level, thus behaving as logic devices; (v) the behaviour of molecular machine components in a biological-type environment; (vi) the study of chemically functionalized metal nanoparticles by second harmonic generation spectroscopy.

Modeling, design and experimental characterization of Micro-Electro-Mechanical-Systems for gas chromatographic applications

Design parameters, process flows, electro-thermal-fluidic simulations and experimental characterizations of Micro-Electro-Mechanical-Systems (MEMS) suited for gas-chromatographic (GC) applications are presented and thoroughly described in this thesis, whose topic belongs to the research activities the Institute for Microelectronics and Microsystems (IMM)-Bologna is involved since several years, i.e. the development of micro-systems for chemical analysis, based on silicon micro-machining techniques and able to perform analysis of complex gaseous mixtures, especially in the field of environmental monitoring. In this regard, attention has been focused on the development of micro-fabricated devices to be employed in a portable mini-GC system for the analysis of aromatic Volatile Organic Compounds (VOC) like Benzene, Toluene, Ethyl-benzene and Xylene (BTEX), i.e. chemical compounds which can significantly affect environment and human health because of their demonstrated carcinogenicity (benzene) or toxicity (toluene, xylene) even at parts per billion (ppb) concentrations. The most significant results achieved through the laboratory functional characterization of the mini-GC system have been reported, together with in-field analysis results carried out in a station of the Bologna air monitoring network and compared with those provided by a commercial GC system. The development of more advanced prototypes of micro-fabricated devices specifically suited for FAST-GC have been also presented (silicon capillary columns, Ultra-Low-Power (ULP) Metal OXide (MOX) sensor, Thermal Conductivity Detector (TCD)), together with the technological processes for their fabrication. The experimentally demonstrated very high sensitivity of ULP-MOX sensors to VOCs, coupled with the extremely low power consumption, makes the developed ULP-MOX sensor the most performing metal oxide sensor reported up to now in literature, while preliminary test results proved that the developed silicon capillary columns are capable of performances comparable to those of the best fused silica capillary columns. Finally, the development and the validation of a coupled electro-thermal Finite Element Model suited for both steady-state and transient analysis of the micro-devices has been described, and subsequently implemented with a fluidic part to investigate devices behaviour in presence of a gas flowing with certain volumetric flow rates.

Prove accelerate per la verifica strutturale di trattrici agricole

The needs of customers to improve machinery in recent years have driven tractor manufacturers to reduce product life and development costs. The most significant efforts have concentrated on the attempt to decrease the costs of the experimental testing sector. The validation of the tractor prototypes are presently performed with a replication of a particularly unfavourable condition a defined number of times. These laboratory tests do not always faithfully reproduce the real use of the tractor. Therefore, field tests are also carried out to evaluate the prototype during real use, but it is difficult to perform such tests for a period of time long enough to reproduce tractor life usage. In this context, accelerated tests have been introduced in the automotive sector, producing a certain damage to the structure in a reduced amount of time. The goal of this paper is to define a methodology for the realization of accelerated structural tests on a tractor, through the reproduction of real customer tractor usage. A market analysis was performed on a 80 kW power tractor and a series of measures were then taken to simulate the real use of the tractor. Subsequently, the rainflow matrixes of the signals were extrapolated and used to estimate the tractor loadings for 10 years of tractor life. Finally these loadings were reproduced on testing grounds with special road pavements. The results obtained highlight the possibility of reproducing field loadings during road driving on proving grounds (PGs), but the use of two field operations is also necessary. The global acceleration factor obtained in this first step of the methodology is equal to three.

Spectroscopic signatures from first principles calculations: from surface adsorbates to liquids and polymers

In dieser Arbeit werden drei wasserstoffverbrückte Systeme in der kondensierten Phase mit Hilfe von first-principles-Elektronenstruktur-Rechnungen untersucht, die auf der Dichtefunktionaltheorie (DFT) unter periodischen Randbedingungen basieren. Ihre lokalen Konformationen und Wasserstoffbrückenbindungen werden mittels ab-initio Molekulardynamiksimulationen berechnet und weiterhin durch die Bestimmung ihrer spektroskopischen Parameter charakterisiert. Der Schwerpunkt liegt dabei auf lokalen Strukturen und auf schnellen Fluktuationen der Wasserstoffbrückenbindungen, welche von zentraler Bedeutung für die physikalischen und chemischen Eigenschaften der betrachteten Systeme sind. Die für die lokalen, instantanen Konformationen berechneten Spektren werden verwendet, um die physikalischen Prozesse, die hinter den untersuchten Phänomenen stehen, zu erklären: die Wasseradsorption auf metallischen Oberflächen, die Ionensolvatisierung in wässrigen Lösungen und der Protonentransport in protonleitenden Polymeren, welche Prototypen von Membranen für Brennstoffzellen sind. Die Möglichkeit der Vorhersage spektroskopischer Parameter eröffnet vielfältige Möglichkeiten des Dialogs zwischen Experimenten und numerischen Simulationen. Die in dieser Arbeit vorgestellten Ergebnisse zeigen, dass die Zuverlässigkeit dieser theoretischen Berechnungen inzwischen für viele experimentell relevante Systeme ein quantitatives Niveau erreicht hat.

Optical Design for Automatic Identification and Portable Systems

This thesis proposes design methods and test tools, for optical systems, which may be used in an industrial environment, where not only precision and reliability but also ease of use is important. The approach to the problem has been conceived to be as general as possible, although in the present work, the design of a portable device for automatic identification applications has been studied, because this doctorate has been funded by Datalogic Scanning Group s.r.l., a world-class producer of barcode readers. The main functional components of the complete device are: electro-optical imaging, illumination and pattern generator systems. For what concerns the electro-optical imaging system, a characterization tool and an analysis one has been developed to check if the desired performance of the system has been achieved. Moreover, two design tools for optimizing the imaging system have been implemented. The first optimizes just the core of the system, the optical part, improving its performance ignoring all other contributions and generating a good starting point for the optimization of the whole complex system. The second tool optimizes the system taking into account its behavior with a model as near as possible to reality including optics, electronics and detection. For what concerns the illumination and the pattern generator systems, two tools have been implemented. The first allows the design of free-form lenses described by an arbitrary analytical function exited by an incoherent source and is able to provide custom illumination conditions for all kind of applications. The second tool consists of a new method to design Diffractive Optical Elements excited by a coherent source for large pattern angles using the Iterative Fourier Transform Algorithm. Validation of the design tools has been obtained, whenever possible, comparing the performance of the designed systems with those of fabricated prototypes. In other cases simulations have been used.