Studies of ferrite, borosilicate and intercalation materials

This thesis is concerned with several aspects of the chemistry of iron compounds. The preparation (with particular emphasis on coprecipitation and sol-gel techniques) and processing of ferrites are discussed. Chapter 2 describes the synthesis of Ni-Zn ferrites with various compositions by three methods. These methods include coprecipitation and sol-gel techniques. The Ni-Zn ferrites were characterised by powder X-ray diffactometry (PXRD), scanning electron microscopy (SEM), vibrating sample magnetometry (VSM), Mössbauer spectroscopy and resistivity measurements. The results for the corresponding ferrites prepared by each method are compared. Chapter 3 reports the sol-gel preparation of a lead borosilicate glass and its addition to Ni-Zn ferrites prepared by the sol-gel method in Chapter 2. The glass-ferrites formed were analysed by the same techniques employed in Chapter 2. Alterations in the microstructure, magnetic and electronic properties of the ferrites due to glass addition are described. Chapter 4 introduces compounds containing Fe-O-B, Fe-O-Si or B-O-Si linkages. The synthesis and characterisation of compounds containing Fe-O-B units are described. The structure of [Fe(SALEN)]2O.CH2Cl2 (17), used in attempts to prepare compounds with Fe-O-Si bonds, was determined by X-ray crystallography. Chapter 4 also details the synthesis of three new borosilicate compounds containing ferrocenyl groups, i.e. [FcBO)2(OSiBut2)2] (19), [(FcBO)2(OSiPh2)2] (20) and [FcBOSiPh3] (21). The structure of (19) was determined by X-ray Crystallographic analysis. Chapter 5 reviews the intercalation properties of the layered host compound iron oxychloride (FeOCI). Intercalation compounds prepared with the microwave dielectric heating technique are also discussed. The syntheses of intercalation compounds by the microwave method with FeOCI as host and ferrocene, ferrocenylboronic acid and 4-aminopyridine as guest species are described. Characterisation of these compounds by powder X-ray diffractometry (PXRD) and M{ssbauer spectroscopy is reported. The attempted synthesis of an intercalation compound with the borosilicate compound (19) as guest species is discussed. Appendices A-E describe the theory and instrumentation involved in powder X-ray diffractometry (PXRD), scanning electron microscopy (SEM0, vibrating sample magnetometry (VSM), Mössbauer spectroscopy and electrical resistivity measurements, respectively. Appendix F details the attempted syntheses of compounds with Fe-O-B and Fe-O-Si linkages.

Nanostructured materials for Lithium-ion battery technology

The Li-ion battery has for several years been at the forefront of powering an ever-increasing number of modem consumer electronic devices such as laptops, tablet PCs, cell phones, portable music players etc., while in more recent times, has also been sought to power a range of emerging electric and hybrid-electric vehicle classes. Given their extreme popularity, a number of features which define the performance of the Li-ion battery have become a target of improvement and have garnered tremendous research effort over the past two decades. Features such as battery capacity, voltage, lifetime, rate performance, together with important implications such as safety, environmental benignity and cost have all attracted attention. Although properties such as cell voltage and theoretical capacity are bound by the selection of electrode materials which constitute its interior, other performance makers of the Li-ion battery such as actual capacity, lifetime and rate performance may be improved by tailoring such materials with characteristics favourable to Li+ intercalation. One such tailoring route involves shrinking of the constituent electrode materials to that of the nanoscale, where the ultra-small diameters may bestow favourable Li+ intercalation properties while providing a necessary mechanical robustness during routine electrochemical operation. The work detailed in this thesis describes a range of synthetic routes taken in nanostructuring a selection of choice Li-ion positive electrode candidates, together with a review of their respective Li-ion performances. Chapter one of this thesis serves to highlight a number of key advancements which have been made and detailed in the literature over recent years pertaining to the use of nanostructured materials in Li-ion technology. Chapter two provides an overview of the experimental conditions and techniques employed in the synthesis and electrochemical characterisation of the as-prepared electrode materials constituting this doctoral thesis. Chapter three details the synthesis of small-diameter V2O5 and V2O5/TiO2 nanocomposite structures prepared by a novel carbon nanocage templating method using liquid precursors. Chapter four details a hydrothermal synthesis and characterisation of nanostructured β-LiVOPO4 powders together with an overview of their Li+ insertion properties while chapter five focuses on supercritical fluid synthesis as one technique in the tailoring of FeF2 and CoF2 powders having potentially appealing Li-ion 'conversion' properties. Finally, chapter six summarises the overall conclusions drawn from the results presented in this thesis, coupled with an indication of potential future work which may be explored upon the materials described in this work.

Method for the in situ preparation of a single layer of zeolite Beta crystals on a molybdenum substrate for microreactor applications

A method for the hydrothermal synthesis of a single layer of zeolite Beta crystals on a molybdenum substrate for microreactor applications has been developed. Before the hydrothermal synthesis, the surface of the substrate was modified by an etching procedure that increases the roughness at the nanoscale level without completely eliminating the surface lay structure. Then, thin films of Al2O3 (170 nm) and TiO2 (50 nm) were successively deposited by atomic layer deposition (ALD) on the substrate. The internal Al2O3 film protects the Mo substrate from oxidation up to 550 degrees C in an oxidative environment. The high wettability of the external TiO2 film after UV irradiation increases zeolite nucleation on its surface. The role of the metal precursor (TiCl4 vs TiI4), deposition temperature (300 vs 500 degrees C), and film thickness (50 vs 100 nm) was investigated to obtain titania films with the slowest decay in the superhydrophilic behavior after UV irradiation. Zeolite Beta coatings with a Si/Al ratio of 23 were grown at 140 degrees C for 48 It. After ion exchange with a 10(-4) M cobalt acetate solution, the activity of the coatings was determined in the ammoxidation of ethylene to acetonitrile in a microstructured reactor. A maximum reaction rate of 220 mu mol C2H3N g(-1) s(-1) was obtained at 500 degrees C, with 42% carbon selectivity to acetonitrile. (C) 2007 Elsevier Inc. All rights reserved.

Oxidative dehydrogenation of propane with N2O over Fe-ZSM-5 and Fe-SiO2: Influence of the iron species and acid sites

A series of iron containing zeolites with varying Si/Al ratios (11.5-140) and low iron content (similar to 0.9 wt.% Fe) have been synthesised by solid-state ion exchange with commercially available zeolites and tested, for the first time, in the oxidative dehydrogenation of propane (ODHP) with N2O. The samples were characterised by XRD, N-2-Adsorption, NH3-TPD and DR-UV-vis spectroscopy. The acidity of the Fe-ZSM-5 can be controlled by high temperature and steam treatments and Si/Al ratio. The selectivity and yield of propene were found to be the highest over Fe-ZSM-5 with low Al contents and reduced acidity. The initial propene yield over Fe-ZSM-5 was significantly higher than that of Fe-SiO2 since the presence of weak and/or medium acid sites together with oligonuclear iron species and iron oxides on the ZSM-5 are found to enhance the N2O activation. The coking of Fe-ZSM-5 catalysts could also be controlled by reduction of the surface acidity of ZSM-5 and by the use of O-2 in addition to N2O as the oxidant. Fe-ZSM-5 zeolites prepared with solid-state method have been shown to have comparable activity and better stability towards coking compared with Fe-ZSM-5 zeolites prepared by liquid ion exchange and hydrothermal synthesis methods. (C) 2012 Elsevier B.V. All rights reserved.

Assessing the greenness of some typical laboratory ionic liquid preparations

The greenness, or lack thereof, of various ionic liquid syntheses and purification methodologies are assessed using a common tool used in strategic planning viz. strengths weaknesses opportunities threats (SWOT) analysis, including their adherence to the twelve principles of green chemistry, % atom economies and E-factors.

Novel microporous silicates and mesoporous MCM materials derivatised with inorganic and organometallic complexes

Os materiais microporosos e mesoporosos são potenciais catalisadores heterogéneos. Os zeólitos e outros materiais microporosos do tipo zeolítico tradicionais, têm átomos tetracoordenados no esqueleto. Nos últimos anos, um vasto número de titanossilicatos contendo Ti(IV) hexacoordenado e Si(IV) tetracoordenado, com estruturas tridimensionais, têm sido alvo de grande interesse. Um dos objectivos desta tese foi preparar silicatos microporosos, contendo átomos metálicos com número de coordenação superior a quatro, e possuindo quer novas estruturas quer propriedades físicas e químicas interessantes. Neste contexto, foi preparado um novo ítriossilicato de sódio, AV-1, análogo do raro mineral montregianite, Na4K2Y2Si16O38·10H2O. Este material é o primeiro sólido microporoso que contem quantidades estequiométricas de sódio (e ítrio) no esqueleto. Foi, também, sintetizado um silicato de cério, AV-5, análogo estrutural do mineral montregianite com potencial aplicação em optoelectrónica. Nesta tese é, ainda, descrita a síntese e caracterização estrutural de um silicato de cálcio hidratado, AV-2, análogo do raro mineral rhodesite (K2Ca4Na2Si16O38.12H2O). Na continuação do trabalho desenvolvido em Aveiro na síntese de novos titanossilicatos surgiu o interesse de preparar novos zirconossilicatos microporosos por síntese hidrotérmica. Foram preparados dois novos materiais análogos dos minerais petarasite Na5Zr2Si3O18(Cl,OH)·2H2O (AV-3) e kostylevite, K2Si3O9·H2O (AV-8). Foram, também, obtidos análogos sintéticos dos minerais parakeldyshite e wadeite, por calcinação a alta temperatura de AV-3 e de umbite sintética. A heterogeneização de complexos organometálicos na superfície de materiais mesoporosos do tipo M41S permite associar a grande actividade catalítica e a presença de sítios activos localizados típicos dos complexos organometálicos, com a robustez e fácil separação, características dos materiais mesoporosos siliciosos. Nesta dissertação relata-se a derivatização dos materiais MCM-41 e MCM-48 através da reacção de [SiMe2{(h5-C5H4)2}]Fe e [SiMe2{(h5-C5H4)2}]TiCl2 com os grupos silanol das superfícies mesoporosas. Os materiais MCMs derivatizados com ansa-titanoceno foram testados na epoxidação de cicloocteno a 323 K na presença de hidrogenoperóxido de t-butilo. Estudou-se a heterogeneização dos sais de complexos com ligação metal-metal [Mo2(MeCN)10][BF4]4, [Mo2(m-O2CMe)2(MeCN)6][BF4]2 e [Mo2(m- O2CMe)2(dppa)2(MeCN)2][BF4]2 via imobilização nos canais do MCM-41. A imobilização dos catalisadores homogéneos na superfície do MCM-41 envolve a saída dos ligandos nitrilo lábeis, preferencialmente em posição axial, através da reacção com os grupos Si-OH da sílica. Verificou-se que a ligação Mo-Mo se mantém intacta nos produtos finais. É provável que estes materiais sejam eficientes catalisadores heterogéneos em reacções de polimerização. As técnicas de caracterização utilizadas nesta tese foram a difracção de raios-X de pós, a microscopia electrónica de varrimento, a espectroscopia de ressonância magnética nuclear do estado sólido (núcleos 13C, 23Na e 29Si), as espectroscopias de Raman e infravermelho com transformadas de Fourier, as análises termogravimétricas e as análises de adsorção de água e azoto.

Ferroelectric : CNTs structures fabrication for advanced functional nano devices

This work is about the combination of functional ferroelectric oxides with Multiwall Carbon Nanotubes for microelectronic applications, as for example potential 3 Dimensional (3D) Non Volatile Ferroelectric Random Access Memories (NVFeRAM). Miniaturized electronics are ubiquitous now. The drive to downsize electronics has been spurred by needs of more performance into smaller packages at lower costs. But the trend of electronics miniaturization challenges board assembly materials, processes, and reliability. Semiconductor device and integrated circuit technology, coupled with its associated electronic packaging, forms the backbone of high-performance miniaturized electronic systems. However, as size decreases and functionalization increases in the modern electronics further size reduction is getting difficult; below a size limit the signal reliability and device performance deteriorate. Hence miniaturization of siliconbased electronics has limitations. On this background the Road Map for Semiconductor Industry (ITRS) suggests since 2011 alternative technologies, designated as More than Moore; being one of them based on carbon (carbon nanotubes (CNTs) and graphene) [1]. CNTs with their unique performance and three dimensionality at the nano-scale have been regarded as promising elements for miniaturized electronics [2]. CNTs are tubular in geometry and possess a unique set of properties, including ballistic electron transportation and a huge current caring capacity, which make them of great interest for future microelectronics [2]. Indeed CNTs might have a key role in the miniaturization of Non Volatile Ferroelectric Random Access Memories (NVFeRAM). Moving from a traditional two dimensional (2D) design (as is the case of thin films) to a 3D structure (based on a tridimensional arrangement of unidimensional structures) will result in the high reliability and sensing of the signals due to the large contribution from the bottom electrode. One way to achieve this 3D design is by using CNTs. Ferroelectrics (FE) are spontaneously polarized and can have high dielectric constants and interesting pyroelectric, piezoelectric, and electrooptic properties, being a key application of FE electronic memories. However, combining CNTs with FE functional oxides is challenging. It starts with materials compatibility, since crystallization temperature of FE and oxidation temperature of CNTs may overlap. In this case low temperature processing of FE is fundamental. Within this context in this work a systematic study on the fabrication of CNTs - FE structures using low cost low temperature methods was carried out. The FE under study are comprised of lead zirconate titanate (Pb1-xZrxTiO3, PZT), barium titanate (BaTiO3, BT) and bismuth ferrite (BiFeO3, BFO). The various aspects related to the fabrication, such as effect on thermal stability of MWCNTs, FE phase formation in presence of MWCNTs and interfaces between the CNTs/FE are addressed in this work. The ferroelectric response locally measured by Piezoresponse Force Microscopy (PFM) clearly evidenced that even at low processing temperatures FE on CNTs retain its ferroelectric nature. The work started by verifying the thermal decomposition behavior under different conditions of the multiwall CNTs (MWCNTs) used in this work. It was verified that purified MWCNTs are stable up to 420 ºC in air, as no weight loss occurs under non isothermal conditions, but morphology changes were observed for isothermal conditions at 400 ºC by Raman spectroscopy and Transmission Electron Microscopy (TEM). In oxygen-rich atmosphere MWCNTs started to oxidized at 200 ºC. However in argon-rich one and under a high heating rate MWCNTs remain stable up to 1300 ºC with a minimum sublimation. The activation energy for the decomposition of MWCNTs in air was calculated to lie between 80 and 108 kJ/mol. These results are relevant for the fabrication of MWCNTs – FE structures. Indeed we demonstrate that PZT can be deposited by sol gel at low temperatures on MWCNTs. And particularly interesting we prove that MWCNTs decrease the temperature and time for formation of PZT by ~100 ºC commensurate with a decrease in activation energy from 68±15 kJ/mol to 27±2 kJ/mol. As a consequence, monophasic PZT was obtained at 575 ºC for MWCNTs - PZT whereas for pure PZT traces of pyrochlore were still present at 650 ºC, where PZT phase formed due to homogeneous nucleation. The piezoelectric nature of MWCNTs - PZT synthesised at 500 ºC for 1 h was proved by PFM. In the continuation of this work we developed a low cost methodology of coating MWCNTs using a hybrid sol-gel / hydrothermal method. In this case the FE used as a proof of concept was BT. BT is a well-known lead free perovskite used in many microelectronic applications. However, synthesis by solid state reaction is typically performed around 1100 to 1300 ºC what jeopardizes the combination with MWCNTs. We also illustrate the ineffectiveness of conventional hydrothermal synthesis in this process due the formation of carbonates, namely BaCO3. The grown MWCNTs - BT structures are ferroelectric and exhibit an electromechanical response (15 pm/V). These results have broad implications since this strategy can also be extended to other compounds of materials with high crystallization temperatures. In addition the coverage of MWCNTs with FE can be optimized, in this case with non covalent functionalization of the tubes, namely with sodium dodecyl sulfate (SDS). MWCNTs were used as templates to grow, in this case single phase multiferroic BFO nanorods. This work shows that the use of nitric solvent results in severe damages of the MWCNTs layers that results in the early oxidation of the tubes during the annealing treatment. It was also observed that the use of nitric solvent results in the partial filling of MWCNTs with BFO due to the low surface tension (<119 mN/m) of the nitric solution. The opening of the caps and filling of the tubes occurs simultaneously during the refluxing step. Furthermore we verified that MWCNTs have a critical role in the fabrication of monophasic BFO; i.e. the oxidation of CNTs during the annealing process causes an oxygen deficient atmosphere that restrains the formation of Bi2O3 and monophasic BFO can be obtained. The morphology of the obtained BFO nano structures indicates that MWCNTs act as template to grow 1D structure of BFO. Magnetic measurements on these BFO nanostructures revealed a week ferromagnetic hysteresis loop with a coercive field of 956 Oe at 5 K. We also exploited the possible use of vertically-aligned multiwall carbon nanotubes (VA-MWCNTs) as bottom electrodes for microelectronics, for example for memory applications. As a proof of concept BiFeO3 (BFO) films were in-situ deposited on the surface of VA-MWCNTs by RF (Radio Frequency) magnetron sputtering. For in situ deposition temperature of 400 ºC and deposition time up to 2 h, BFO films cover the VA-MWCNTs and no damage occurs either in the film or MWCNTs. In spite of the macroscopic lossy polarization behaviour, the ferroelectric nature, domain structure and switching of these conformal BFO films was verified by PFM. A week ferromagnetic ordering loop was proved for BFO films on VA-MWCNTs having a coercive field of 700 Oe. Our systematic work is a significant step forward in the development of 3D memory cells; it clearly demonstrates that CNTs can be combined with FE oxides and can be used, for example, as the next 3D generation of FERAMs, not excluding however other different applications in microelectronics.

Growth and characterization of nanostructured wide band gap semiconductors for optoelectronic applications

Department of Physics, Cochin University of Science and Technology

Growth and characterisation of p-type delafossite transparent conducting thin films for heterojunction applications

In the present studies, various copper delafossite materials viz; CuAlO2, CuGaO2, CuFeO2 , CuGa1-xFexO2, CuYO2 and CuCaxY1-xO2 were synthesised by solid state reaction technique. These copper delafossite materials were grown in thin film form by rf magnetron sputtering technique. In general copper delafossites exhibit good optical transparency. The conductivity of the CuYO2 could be improved by Ca doping or by oxygen intercalation by annealing the film in oxygen atmosphere. It has so far been impossible to improve the p-type conductivity of CuGaO2 significantly by doping Mg or Ca on the Ga site. The ptype conductivity is presumed to be due to oxygen doping or Cu Vacancies [6]. Reports in literature show, oxygen intercalation or divalent ion doping on Ga site is not possible for CuGaO2 thin films to improve the p-type conductivity. Sintered powder and crystals of CuFeO2 have been reported as the materials having the highest p-type conductivity [14, 15] among the copper and silver delafossites. However the CuFeO2 films are found to be less transparent in the visible region compared to CuGaO2. Hence in the present work, the solid solution between the CuGaO2 and CuFeO2 was effected by solid state reaction, varying the Fe content. The CuGa1-xFexO2 with Fe content, x=0.5 shows an increase in conductivity by two orders, compared to CuGaO2 but the transparency is only about 50% in the visible region which is less than that of CuGaO2 The synthesis of α−AgGaO2 was carried out by two step process which involves the synthesis of β-AgGaO2 by ion exchange reaction followed by the hydrothermal conversion of the β-AgGaO2 into α-AgGaO2. The trace amount of Ag has been reduced substantially in the two step synthesis compared to the direct hydrothermal synthesis. Thin films of α-AgGaO2 were prepared on silicon and Al2O3 substrates by pulsed laser deposition. These studies indicate the possibility of using this material as p-type material in thin film form for transparent electronics. The room temperature conductivity of α-AgGaO2 was measured as 3.17 x 10-4 Scm-1and the optical band gap was estimated as 4.12 eV. A transparent p-n junction thin film diode on glass substrate was fabricated using p-type α-AgGaO2 and n-ZnO.AgCoO2 thin films with 50% transparency in the visible region were deposited on single crystalline Al2O3 and amorphous silica substrates by RF magnetron sputtering and p type conductivity of AgCoO2 was demonstrated by fabricating transparent p-n junction diode with AgCoO2 as p-side and ZnO: Al as n-side using sputtering. The junction thus obtained was found to be rectifying with a forward to reverse current of about 10 at an applied voltage of 3 V.The present study shows that silver delafossite thin films with p-type conductivity can be used for the fabrication of active devices for transparent electronics applications.

Diazafluoren-9-yliden als Bindungsmotiv für Metallfragmente in kreuzkonjugierten π-Systemen

In der vorliegenden Dissertation wurden kreuzkonjugierte organische Verbindungen basierend auf Diazafluorenmethyliden- sowie Dipyridylmethyliden-Bausteinen synthetisiert, die zum einen photoredoxaktive Metallfragmente komplexieren können und zum anderen erweiterte π-konjugierte Pfade auf der Grundlage von Alkineinheiten ermöglichen. Das kreuzkonjugierte Motiv wurde über die Kupplung von Alkineinheiten an halogenierte Methyliden-Einheiten, den so genannten Dibromolefinen, zugänglich gemacht. Zur Synthese von Dibromolefinen wurden verschiedene Methoden untersucht. Literaturbekannte Methoden wie die Wittig-Reaktion und ihre Modifikationen sowie die Corey-Fuchs-Reaktion konnten für die Diazafluoreneinheit nicht erfolgreich angewendet werden. Bei einer mikrowellenunterstützten Reaktion konnte sowohl ausgehend von Diazafluoren-9-on als auch von Di-2-pyridylketon eine Dibromolefinierung (55 % und 65 %) erreicht werden. Die Eignung der Mikrowellenstrahlung für Dibromolefinierungsreaktionen nach Corey und Fuchs wurde weiterhin an verschiedenen Aldehyden und Ketonen untersucht. In den meisten Fällen konnten gute bis sehr gute Ergebnisse erzielt werden. Durch die erfolgreiche Synthese von Dibromolefinen über Mikrowellensynthese wurde die Realisierung von diversen π-konjugierten Systemen möglich. Dies erfolgte exemplarisch durch die Kupplung der Alkine 5-Ethinyl-2,2’-bipyridin, 1-(Ferrocenylethinyl)-4-(ethinyl)benzol, Tri(tolyl)propin sowie der TIPS- und TMS-Acetylene. Neben der Vielfalt an Möglichkeiten zur Funktionalisierung von Dipyridyl- und Diazafluorenbausteinen zeigte sich zudem, dass sogar räumlich anspruchsvolle Verbindungen wie die geminale angeordneten voluminösen Tri(tolyl)propinyl-Substituenten an der Doppelbindung erfolgreich synthetisiert werden können. Die Koordinationseigenschaften der neu synthetisierten Verbindungen konnten durch Umsetzungen der Diazafluoren- und Dipyridylverbindungen mit PdCl2 und [RuCl2(bpy)2] erfolgreich gezeigt werden. Im Hinblick auf die Herstellung von Funktionsmaterialien eignen sich die Endiin-Strukturmotive aufgrund von diversen Variationsmöglichkeiten wie Koordination von Übergangsmetallen sowie Funktionalisierung der Peripherie gut. Dadurch können die elektronischen Eigenschaften wie die Absorption oder elektrochemische Potentiale der Verbindungen modifiziert werden. Die UV/Vis-Spektren der neu synthetisierten Verbindungen zeigen, dass Absorptionen in längerwelligen Bereichen durch Verlängerung des Konjugationspfades gesteuert werden können. Zudem lassen sich weitere photophysikalische Eigenschaften wie MC-, LC-, LMCT- oder MLCT-Übergänge durch Koordination von Metallen generieren. Die elektrochemischen Potentiale der Dipyridyl- und Diazafluorenbausteine konnten durch Anbindung von verschiedenen Substituenten beeinflusst werden. Es zeigte sich, dass sich die Reduktionswellen im Vergleich zu denen der Ketone zu niedrigeren Potentialen verschieben, wenn Alkine an die Dipyridylmethyliden- und Diazafluorenmethyliden-Bausteine geknüpft wurden. Zudem konnte beobachtet werden, dass die Signale nicht immer reversibel sind. Insbesondere die Dipyridylverbindungen zeichneten sich durch irreversible Reduktionswellen aus. Die Realisierung von π-konjugierten Systemen gelang auch mit cyclischen kohlenstoffbasierten Verbindungen. Über das separat synthetisierte 2,2’-Diethinyltolan konnte eine cyclische Verbindung, ein dehydroannulen-radialenisches System, erfolgreich hergestellt werden. Die Koordination von redoxaktiven Metallzentren wie [Ru(bpy)2] konnte für diese Verbindung ebenfalls erfolgreich gezeigt werden. Die elektronische Wechselwirkung zwischen dem Metallzentrum und dem dehydroannulenischen System könnte sowohl über theoretische Methoden (zeitabhängige Dichtefunktionaltheorie) als auch experimentell wie z. B. über transiente Absorptionsspektroskopie untersucht werden. Diese zukünftig durchzuführenden Untersuchungen können Aufschluss über die Ladungstransferraten und -dauer geben. Im Hinblick auf die Realisierung von Modellverbindungen für molekulare Drähte wurden lineare Systeme basierend auf der Diazafluoreneinheit synthetisiert. Zur Synthese von derartigen Systemen war es zunächst notwendig, die Dibromolefine unsymmetrisch zu alkinylieren. Die unsymmetrische Substitution gestaltete sich als Herausforderung, da eine Einfachkupplung mit einem Acetylen nicht möglich war. In den meisten Fällen wurden zweifach substituierte Spezies mit den identischen Alkinen erhalten. Die besten Ausbeuten konnten durch die konsekutive Zugabe von TIPS-Acetylen und darauffolgend TMS-Acetylen in die Reaktionsmischung erhalten werden. Offenbar spielt der räumliche Anspruch des Erstsubstituenten in diesem Zusammenhang eine Rolle. Die selektive Entschützung der unterschiedlich silylierten Verbindungen erfolgte mit K2CO3 in MeOH/THF (1:1). Die oxidative Homokupplungsreaktion erfolgte ohne Isolierung der entschützten Spezies, da diese instabil ist und zur Polymerisation neigt. Aufgrund der Instabilität der entschützten Spezies sowie möglichen Nebenreaktionen waren die Ausbeuten sowohl bei der TIPS-geschützten Verbindung als auch bei der TTP-geschützten Verbindung gering. Versuche, lineare Systeme von dipyridylbasierten Verbindungen zu erhalten, schlugen fehl. Die π-konjugierten Systeme lassen aufgrund der effektiven Überlappung der beteiligten π-Orbitale hohe Ladungsträgermobilitäten vermuten. Die im Rahmen dieser Arbeit synthetisierten Verbindungen könnten mit Schwefelverbindungen die Anbindung an Elektroden zulassen, worüber die Leitfähigkeiten der Verbindungen gemessen werden könnten.

A new processing method of CaZn(2)(OH)(6)center dot 2H(2)O powders: Photoluminescence and growth mechanism

In this communication, we report on the formation of calcium hexahydroxodizincate dehydrate, CaZn(2)(OH)(6)center dot 2H(2)O (CZO) powders under microwave-hydrothermal (MH) conditions. These powders were analyzed by X-ray diffraction (XRD), Field-emission gum scanning electron microscopy (FEG-SEM), ultraviolet-visible (UV-vis) absorption spectroscopy and photoluminescence (PL) measurements. XRD patterns confirmed that the pure CZO phase was obtained after MH processing performed at 130 degrees C for 2 h. FEG-SEM micrographs indicated that the morphological modifications as well as the growth of CZO microparticles are governed by Ostwald-ripening and coalescence mechanisms. UV-vis spectra showed that this material have an indirect optical band gap. The pure CZO powders exhibited an yellow PL emission when excited by 350 nm wavelength at room temperature. (C) 2009 Elsevier Masson SAS. All rights reserved.

Formation of beta-nickel hydroxide plate-like structures under mild conditions and their optical properties

Nanostructural beta-nickel hydroxide (beta-Ni(OH)(2)) plates were prepared using the microwave hydrothermal (MH) method at a low temperature and short reaction times. An ammonia solution was employed as the coordinating agent, which reacts with [Ni(H(2)O)(6)](2+) to control the growth of beta-Ni(OH)(2) nuclei. A trigonal beta-Ni(OH)(2) single phase was observed by X-ray diffraction (XRD) analyses, and the crystal cell was constructed with structural parameters and atomic coordinates obtained from Rietveld refinement. Field emission scanning electron microscopy (FE-SEM) images revealed that the samples consisted of hexagonal-shaped nanoplates with a different particle size distribution. Broad absorption bands assigned as transitions of Ni(2+) in oxygen octahedral sites were revealed by UV-vis spectra. Photoluminescence (PL) properties observed with a maximum peak centered in the blue-green region were attributed to different defects, which were produced during the nucleation process. We present a growth process scheme of the beta-Ni(OH)(2) nanoplates. (C) 2011 Elsevier Inc. All rights reserved.

Síntese, caracterização e estudo da regeneração do silicoaluminofosfato-11 (SAPO-11)

heterogeneous catalyst such as a silicoaluminophosphate, molecular sieve with AEL (Aluminophosphate eleven) structure such as SAPO-11, was synthesized through the hydrothermal method starting from silica, pseudoboehmite, orthophosphoric acid (85%) and water, in the presence of a di-isopropylamine organic template. For the preparation of SAPO-11 in a dry basis it was used as reactants: DIPA; H3PO4; SiO4; Pseudoboehmite and distilled water. The crystallization process occurred when the reactive hydrogel was charged into a vessel and autoclaved at 200ºC for a period of 72 hours under autogeneous pressure. The obtained material was washed, dried and calcined to remove the molecular sieves of DIPA. The samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), infrared spectroscopy (FT-IR), nitrogen adsorption (BET) and thermal analysis (TG/DTG). The acidic properties were determined using adsorption of nbutylamine followed by programmed thermodessorption. This method revealed that SAPO-11 shows an acidity that ranges from weak to moderate. However, a small quantity of strong acid sites could be detected there. The deactivation of the catalysts was conducted by artificial coking followed by the cracking of the n-hexane in a fixed bed with a continuous flow micro-reactor coupled on line to a gas chromatograph. The main products obtained were: ethane, propane, isobutene, n-butane, n-pentane and isopentane. The Vyazovkin (model-free) kinetics method was used to determine the regeneration and removal of the coke

Síntese e impregnação de peneiras moleculares Fe MCM-41 derivada de sílica da casca do arroz

The mesoporous molecular sieves of the MCM-41 and FeMCM-41 type are considered promissory as support for metals used as catalysts in oil-based materials refine processes and as adsorbents for environmental protection proposes. In this work MCM-41 and FeMCM41 were synthesized using rice husk ash - RHA as alternative to the conventional silica source. Hydrothermal synthesis was the method chosen to prepare the materials. Pre-defined synthesis parameters were 100°C for 168 hours, later the precursor was calcinated at 550°C for 2 hours under nitrogen and air flow. The sieves containing different proportions of iron were produced by two routes: introduction of iron salt direct synthesis; and a modification post synthesis consisting in iron salt 1 % and 5% impregnation in the material followed by thermal decomposition. The molecular sieves were characterized by X ray diffraction XRD, Fourier transform infrared spectroscopy FT-IR, X ray fluorescence spectroscopy XFR, scanning electronic microscopy SEM, specific surface area using the BET method, Termogravimetry TG. The kinetic model of Flynn Wall was used with the aim of determining the apparent activation energy of the surfactant remove (CTMABr) in the MCM- 41 porous. The analysis made possible the morphology characterization, identifying the presence of hexagonal structure typical for mesoporous materials, as well as observation of the MCM41 and iron of characteristic bands.