Reduced calcification decreases photoprotective capability in the Coccolithophorid Emiliania huxleyi

Intracellular calcification of coccolithophores generates CO2 and consumes additional energy for acquisition of calcium and bicarbonate ions; therefore, it may correlate with photoprotective processes by influencing the energetics. To address this hypothesis, a calcifying Emiliania huxleyi strain (CS-369) was grown semi-continuously at reduced (0.1 mM, LCa) and ambient Ca2+ concentrations (10 mM, HCa) for 150 d (>200 generations). The HCa-grown cells had higher photosynthetic and calcification rates and higher contents of Chl a and carotenoids compared with the naked (bearing no coccoliths) LCa-grown cells. When exposed to stressfull levels of photosynthetically active radiation (PAR), LCa-grown cells displayed lower photochemical yield and less efficient non-photochemical quenching (NPQ). When the LCa- or HCa-grown cells were inversely shifted to their counterpart medium, LCa to HCa transfer increased photosynthetic carbon fixation (P), calcification rate (C), the C/P ratio, NPQ and pigment contents, whereas those shifted from HCa to LCa exhibited the opposite effects. Increased NPQ, carotenoids and quantum yield were clearly linked with increased or sustained calcification in E. huxleyi. The calcification must have played a role in dissipating excessive energy or as an additional drainage of electrons absorbed by the photosynthetic antennae. This phenomenon was further supported by testing two non-calcifying strains, which showed insignificant changes in photosynthetic carbon fixation and NPQ when transferred to LCa conditions

Applying life cycle assessment to analyze the environmental sustainability of public transit modes for the City of Toronto

One challenge related to transit planning is selecting the appropriate mode: bus, light rail transit (LRT), regional express rail (RER), or subway. This project uses data from life cycle assessment to develop a tool to measure energy requirements for different modes of transit, on a per passenger-kilometer basis. For each of the four transit modes listed, a range of energy requirements associated with different vehicle models and manufacturers was developed. The tool demonstrated that there are distinct ranges where specific transit modes are the best choice. Diesel buses are the clear best choice from 7-51 passengers, LRTs make the most sense from 201-427 passengers, and subways are the best choice above 918 passengers. There are a number of other passenger loading ranges where more than one transit mode makes sense; in particular, LRT and RER represent very energy-efficient options for ridership ranging from 200 to 900 passengers. The tool developed in the thesis was used to analyze the Bloor-Danforth subway line in Toronto using estimated ridership for weekday morning peak hours. It was found that ridership across the line is for the most part actually insufficient to justify subways over LRTs or RER. This suggests that extensions to the existing Bloor-Danforth line should consider LRT options, which could service the passenger loads at the ends of the line with far greater energy efficiency. It was also clear that additional destinations along the entire transit line are necessary to increase the per passenger-kilometer energy efficiency, as the current pattern of commuting to downtown leaves much of the system underutilized. It is hoped that the tool developed in this thesis can be used as an additional resource in the transit mode decision-making process for many developing transportation systems, including the transit systems across the GTHA.

Techno-Economic and Life Cycle Assessment for the Production of Green Composites

Botanically, green composites belong to an economically important seed plant family that includes maize, wheat, rice, and sorghum known as Saccharum offi cinarum. There are so many natural fibers available in the environment such as rice husk, hemp fibers, flax fibers, bamboo fibers, coconut fiber, coconut coir, grawia optiva and many others also. Life Cycle Assessment (LCA) is a process to estimate the environmental feature and potential impacts related to a product, by organizing a directory of pertinent inputs and outputs of a product system, assessing the potential environmental impacts related with the said inputs and outputs, explaining the results of the inventory analysis and impact evaluation phases in connection to the objectives of the study. Particularly Bagasse, an agricultural residue not only becomes a problem from the environmental point of view, but also affects the profitability of the sugarcane industries. This chapter discusses the properties, processing methods and various other aspects including economic and environmental aspects related to green composites.

Correlación entre los resultados de valoración funcional y de fuerza de la rodilla en pacientes con rotura del ligamento cruzado anterior

Programa de doctorado: Avances en Traumatología. Medicina del Deporte. Cuidado de Heridas. La fecha de publicación es la fecha de lectura

Un esempio di Economia Circolare: il riciclo e il riuso dei dispositivi Tessili per Sala Operatoria

Negli ultimi decenni l’attenzione alle tematiche della sostenibilità ambientale e dell’inquinamento globale da parte dell’opinione pubblica e delle imprese è in costante aumento. Una tra le principali fonti di inquinamento è costituita dai rifiuti, e di conseguenza, la loro gestione e il loro smaltimento sono diventate una priorità, non solo per le istituzioni, ma anche per le imprese e per i cittadini. Inoltre la crescita della domanda delle risorse presenti in natura è in costante aumento e l’approvvigionamento di esse si è rivelato essere invece soggetto a significativi limiti. In questo attuale contesto quindi, il modello economico lineare fino ad oggi utilizzato, “take-make-dispose”, non risulta più idoneo. Si è sviluppato così il concetto di “Economia Circolare”. L’obiettivo di questa economia è quello di eliminare il concetto di scarto, il rifiuto deve essere considerato una vera e propria risorsa. In questo sistema tutte le attività, a partire dall’ estrazione fino ad arrivare alla produzione, sono organizzate in modo che i rifiuti di uno diventino risorse per un altro. L’obiettivo della tesi è quello di applicare il concetto di Economia Circolare al mercato dei dispositivi tessili per sala operatoria (DTSO), utilizzando la valutazione del ciclo di vita di un prodotto (analisi LCA) in modo da individuare le fasi più critiche e poter operare dei miglioramenti. Dopo essere stati sottoposti a 70 cicli di lavaggio e sterilizzazione i dispositivi TTR (Tessuti Tecnici Riutilizzabili) non sono più idonei ad essere utilizzati in ambito ospedaliero e vengono smaltiti in discarica , così come vengono smaltiti altri miliardi di rifiuti ogni giorno.Questi tessuti, seppur non conformi agli standard qualitativi richiesti dalle norme ospedaliere, possono essere riciclati o riutilizzati in prodotti di altro tipo. L’obiettivo di questo lavoro è quello di reimmettere questi dispositivi in un ciclo di vita di un nuovo prodotto, in ottica appunto di economia circolare.

Biopolttoaineilla kestävyyttä merenkulkuun? Elinkaariarviointi kestävyyden mittarina

Merenkulun ilmapäästöillä on laajoja vaikutuksia sekä ilmanlaatuun, ilmaston-muutokseen että ihmisten terveyteen. Muiden liikennemuotojen päästöihin on puututtu jo pitkään, mutta merenkulun yhteydessä International Maritime Organisation IMO on asettanut rajoituksia mm. rikkipäästöille vasta viime vuosina. Itämeri on saanut erityisaseman ns. SECA-alueena, jolla operoivien alusten polttoaineen rikkipitoisuus ei saa ylittää 0,1 prosenttia. Yhtenä ratkaisuna päästöongelmiin voivat toimia biopolttoaineet. Liikennekäyttöön tarkoitettuja biopolttoaineita on jo kaupallisessa käytössä ja mm. jätepohjaisia raaka-aineita tutkitaan parhaillaan. EU:n biopolttoaineita käsittelevät säädökset edellyttävät, että tuotannon on oltava kestävää, jotta sillä saavutetaan todellisia kasvihuonekaasupäästöjen vähennyksiä. Kestävyyden arviointiin paras keino on elinkaariarviointi eli LCA, jonka avulla voidaan laskennallisesti osoittaa päästövähennykset verrattuna fossiilisen poltto-ainetuotannon ja käytön tuottamiin päästöihin. Elinkaariarviointi ottaa huomioon tuotantoketjun kaikki päästöt aina raaka-aineen tuottamisesta tuotteen hävittämiseen saakka. Tässä tutkimuksessa elinkaariarviointi suoritettiin Turussa sijaitsevan VG-Shipping -varustamon tarpeisiin. Tuloksia käytetään lain edellyttämän toiminnan-harjoittajan kestävyysjärjestelmän luomiseen sekä sen arviointiin, miten elinkaariarviointi toimii kestävyyden mittarina. VG-Shipping tuottaa oman varustamotoimintansa tarpeisiin jätepohjaisista raaka-aineista tuotettua bioöljyä ja -dieseliä. Elinkaariarviointi osoitti tuotannon olevan kestävällä tasolla ja päästövähennysten olevan fossiiliseen vertailukohtaan nähden eri tuotantoketjuilla 84-96 prosentin välillä.

Produção de CDR a partir de resíduos industriais: caso de estudo da Recivalongo

A produção de combustível derivado de resíduos (CDR) resultou de uma decisão política que permitiu a instalação em Portugal de um significativo conjunto de processos, cuja avaliação técnico-económica e ambiental pode já ser feita. Este trabalho faz uma avaliação técnica e ambiental da linha de produção de CDR da Recivalongo. A avaliação técnica consistiu na análise dos caudais de material que entraram na linha de produção, na quantidade de CDR produzido, contabilizando também os gastos de recursos da linha (energia e materiais auxiliares). A avaliação da qualidade de CDR produzido a partir do ensaio laboratorial representou também uma parte muito significativa do trabalho produzido. A avaliação ambiental foi efetuada com base na metodologia da Avaliação de Ciclo de Vida (ACV). Os resultados obtidos permitiram concluir que o processo da Recivalongo transforma 69% do material de entrada, recuperando 2% em metais ferrosos e rejeitando para aterro a restante fração de 29%. As análises efetuadas ao CDR mostraram que apresenta um PCI compreendido entre 17 e 20 MJ/kg; o teor em cloro está compreendido entre 0,2 e 0,8% Conclui-se que neste processo o parâmetro mais difícil de controlar é o teor em cloro no CDR, pois existe uma grande diversidade de resíduos com grandes quantidades de cloro na sua constituição e que por muitas vezes são difíceis de identificar e/ou separar na primeira fase do tratamento dos resíduos. Da análise ciclo de vida efetuada à produção de CDR pode-se afirmar que esta operação de gestão de resíduos apresenta uma mais-valia quando comparada com a deposição dos resíduos em aterro, não sendo a diferença entre destinos tão significativa quanto o esperado. Desta avaliação pode concluir-se que a instalação operou muito abaixo da sua capacidade, sendo esta considerada uma das melhores linhas de produção de CDR a nível nacional.

Développement d’une stratégie de modification du bois afin de limiter les variations dimensionnelles du produit lambris dans un contexte éco-responsable

Ce travail de thèse présente deux grands axes. Le premier axe, touche les traitements du bois dans le but principal de réduire les variations dimensionnelles et d’améliorer la résistance à l’attaque des champignons lignivores. Le second axe quant à lui, touche l’aspect environnemental du traitement acide citrique-glycérol. Ce dernier a pour but principal de démontrer que le prolongement de la durée de vie en service du produit lambris traité, compense les impacts environnementaux causés par ce traitement. Dans le premier axe, deux traitements ont été réalisés sur deux essences de pin (Pinus strobus L. et Pinus contorta D.). Un traitement à l’anhydride maléique et un autre traitement avec une solution d’acide citrique – glycérol brute (AC-G). Dans le premier cas, les effets de deux paramètres (la durée de séchage et la température d’estérification) sur les résultats des essais de stabilité dimensionnelle, de résistance à la dégradation fongique et de vieillissement accéléré ont été évalués. Trois niveaux de durée de séchage après imprégnation (12 h, 18 h et 24 h) et trois niveaux de température d’estérification (140 °C, 160 °C et 180 °C) ont été considérés. Dans le second cas, après identification du meilleur catalyseur (HCl) et du meilleur ratio acide citrique – glycérol (3/1) pendant les essais préliminaires, les performances de ce traitement sur la stabilité dimensionnelle, la résistance à la pourriture fongique, la dureté de surface et l’adhérence des couches de revêtement de peinture sur la surface du substrat bois ont été analysées. Les résultats obtenus ont été appuyés par une suite d’analyses qualitatives et quantitatives pour mieux comprendre et expliquer. Les analyses qualitatives sont : (i) la spectroscopie infrarouge à transformée de Fourier (IRTF) et (ii) la microscopie électronique à balayage (MEB) tandis que la quantitative, l’analyse par perte de masse a été faite par pesée. Dans le second axe, une analyse des impacts environnementaux du traitement AC-G a été effectuée par le biais du logiciel SimaPro v8. La base de données Ecoinvent v3 et la méthode d’analyse d’impact Impact 2002+ ont été utilisées dans cette partie du travail de thèse. Sur la base des résultats du second traitement (AC-G) et des travaux disponibles dans la littérature, nous avons estimé, une durée de vie en service des lambris traités. Les différents scénarios de la durée de vie du lambris traité mis sur pied par rapport à celle offerte aujourd’hui par l’industrie, nous permettent de modéliser les impacts environnementaux du traitement. A cette fin, l’analyse de cycle de vie (ACV) a été utilisée comme outil de conception. En conclusion, les paramètres, durée de séchage et température d’estérification influencent les résultats obtenus dans le cas du traitement du bois à l’anhydride maléique. La combinaison 24 h de séchage et 180 °C, température d’estérification, représente les paramètres qui offrent les meilleurs résultats de stabilité dimensionnelle, de résistance à la dégradation fongique et de vieillissement accéléré. Le traitement AC-G améliore la stabilité dimensionnelle, la résistance à la dégradation fongique et la dureté de surface des échantillons. Cependant, le traitement réduit l’adhérence des couches de peinture. Les impacts environnementaux produits par le traitement AC-G sont majoritairement liés à la consommation de la ressource énergie (électricité). Le traitement prolonge la durée de vie en service du lambris traité et il a été mis en évidence que le scénario de durée de vie qui permettrait que le lambris traité puisse se présenter comme un produit à faible impact environnemental par rapport au lambris non traité est celui d’une durée de vie de 55 ans.

Environmental impacts of freshwater use and suspended solids in life cycle assessment

Perturbation of natural ecosystems, namely by increasing freshwater use and its degradative use, as well as topsoil erosion by water of land-use production systems, have been emerging as topics of high environmental concern. Freshwater use has become a focus of attention in the last few years for all stakeholders involved in the production of goods, mainly agro-industrial and forest-based products, which are freshwater-intensive consumers, requiring large inputs of green and blue water. This thesis presents a global review on the available Water Footprint Assessment and Life Cycle Assessment (LCA)-based methods for measuring and assessing the environmental relevance of freshwater resources use, based on a life cycle perspective. Using some of the available midpoint LCA-based methods, the freshwater use-related impacts of a Portuguese wine (white ‘vinho verde’) were assessed. However, the relevance of environmental green water has been neglected because of the absence of a comprehensive impact assessment method associated with green water flows. To overcome this constraint, this thesis helps to improve and enhance the LCA-based methods by providing a midpoint and spatially explicit Life Cycle Impact Assessment (LCIA) method for assessing impacts on terrestrial green water flow and addressing reductions in surface blue water production caused by reductions in surface runoff due to land-use production systems. The applicability of the proposed method is illustrated by a case study on Eucalyptus globulus conducted in Portugal, as the growth of short rotation forestry is largely dependent on local precipitation. Topsoil erosion by water has been characterised as one of the most upsetting problems for rivers. Because of this, this thesis also focuses on the ecosystem impacts caused by suspended solids (SS) from topsoil erosion that reach freshwater systems. A framework to conduct a spatially distributed SS delivery to freshwater streams and a fate and effect LCIA method to derive site-specific characterisation factors (CFs) for endpoint damage on aquatic ecosystem diversity, namely on algae, macrophyte, and macroinvertebrates organisms, were developed. The applicability of this framework, combined with the derived site-specific CFs, is shown by conducting a case study on E. globulus stands located in Portugal as an example of a land use based system. A spatially explicit LCA assessment was shown to be necessary, since the impacts associated with both green water flows and SS vary greatly as a function of spatial location.

As Implicações do novo regime financeiro das autarquias locais no apuramento do endividamento do grupo municipal

Dissertação de Mestrado em Auditoria

Exergetic, energetic, economic and environmental evaluation of concentrated solar power plants in Libya

The PhD project addresses the potential of using concentrating solar power (CSP) plants as a viable alternative energy producing system in Libya. Exergetic, energetic, economic and environmental analyses are carried out for a particular type of CSP plants. The study, although it aims a particular type of CSP plant – 50 MW parabolic trough-CSP plant, it is sufficiently general to be applied to other configurations. The novelty of the study, in addition to modeling and analyzing the selected configuration, lies in the use of a state-of-the-art exergetic analysis combined with the Life Cycle Assessment (LCA). The modeling and simulation of the plant is carried out in chapter three and they are conducted into two parts, namely: power cycle and solar field. The computer model developed for the analysis of the plant is based on algebraic equations describing the power cycle and the solar field. The model was solved using the Engineering Equation Solver (EES) software; and is designed to define the properties at each state point of the plant and then, sequentially, to determine energy, efficiency and irreversibility for each component. The developed model has the potential of using in the preliminary design of CSPs and, in particular, for the configuration of the solar field based on existing commercial plants. Moreover, it has the ability of analyzing the energetic, economic and environmental feasibility of using CSPs in different regions of the world, which is illustrated for the Libyan region in this study. The overall feasibility scenario is completed through an hourly analysis on an annual basis in chapter Four. This analysis allows the comparison of different systems and, eventually, a particular selection, and it includes both the economic and energetic components using the “greenius” software. The analysis also examined the impact of project financing and incentives on the cost of energy. The main technological finding of this analysis is higher performance and lower levelized cost of electricity (LCE) for Libya as compared to Southern Europe (Spain). Therefore, Libya has the potential of becoming attractive for the establishment of CSPs in its territory and, in this way, to facilitate the target of several European initiatives that aim to import electricity generated by renewable sources from North African and Middle East countries. The analysis is presented a brief review of the current cost of energy and the potential of reducing the cost from parabolic trough- CSP plant. Exergetic and environmental life cycle assessment analyses are conducted for the selected plant in chapter Five; the objectives are 1) to assess the environmental impact and cost, in terms of exergy of the life cycle of the plant; 2) to find out the points of weakness in terms of irreversibility of the process; and 3) to verify whether solar power plants can reduce environmental impact and the cost of electricity generation by comparing them with fossil fuel plants, in particular, Natural Gas Combined Cycle (NGCC) plant and oil thermal power plant. The analysis also targets a thermoeconomic analysis using the specific exergy costing (SPECO) method to evaluate the level of the cost caused by exergy destruction. The main technological findings are that the most important contribution impact lies with the solar field, which reports a value of 79%; and the materials with the vi highest impact are: steel (47%), molten salt (25%) and synthetic oil (21%). The “Human Health” damage category presents the highest impact (69%) followed by the “Resource” damage category (24%). In addition, the highest exergy demand is linked to the steel (47%); and there is a considerable exergetic demand related to the molten salt and synthetic oil with values of 25% and 19%, respectively. Finally, in the comparison with fossil fuel power plants (NGCC and Oil), the CSP plant presents the lowest environmental impact, while the worst environmental performance is reported to the oil power plant followed by NGCC plant. The solar field presents the largest value of cost rate, where the boiler is a component with the highest cost rate among the power cycle components. The thermal storage allows the CSP plants to overcome solar irradiation transients, to respond to electricity demand independent of weather conditions, and to extend electricity production beyond the availability of daylight. Numerical analysis of the thermal transient response of a thermocline storage tank is carried out for the charging phase. The system of equations describing the numerical model is solved by using time-implicit and space-backward finite differences and which encoded within the Matlab environment. The analysis presented the following findings: the predictions agree well with the experiments for the time evolution of the thermocline region, particularly for the regions away from the top-inlet. The deviations observed in the near-region of the inlet are most likely due to the high-level of turbulence in this region due to the localized level of mixing resulting; a simple analytical model to take into consideration this increased turbulence level was developed and it leads to some improvement of the predictions; this approach requires practically no additional computational effort and it relates the effective thermal diffusivity to the mean effective velocity of the fluid at each particular height of the system. Altogether the study indicates that the selected parabolic trough-CSP plant has the edge over alternative competing technologies for locations where DNI is high and where land usage is not an issue, such as the shoreline of Libya.

Different approaches to municipal solid waste management in Brazil : case study Rio de Janeiro

Inadequate final disposal of municipal solid waste (MSW) is associated with significant greenhouse gas (GHG) emission, environmental, health and safety issues, space consumption, public health and developmental issues in general. The environmental impact of waste is mostly felt in developing countries, inadequate waste management and treatment solution, inadequate policies and outdated practices are some of the factors leading to the significantly high final disposal of waste in dumps in developing countries. Brazil and other developing countries are changing the status quo by adopting polices that will adequately address this problem of inadequate waste management and disposal. Life cycle analysis (LCA) identifies the potential environmental impact of a product though environmental impact assessment, International Organization for Standardization (ISO) created the ISO 14040 and ISO 14044 to serve as principle guidelines for conducting LCA. Various waste treatment solution was applied to identify the waste management solution with the least Global warming potential (GWP) for treating the MSW generated from the city of Rio de Janerio, while reducing significantly final waste disposed in landfill.

Biofuels and high value added products from the yeast Rhodosporidium toruloides NCYC 921: Strategies towards a true cost-effective and environmentally sustainable integrated multiproduct driven biorefinery [Poster]

Single-cell oils (SCO) have been considered a promising source of 3rd generation biofuels mainly in the final form of biodiesel. However, its high production costs have been a barrier towards the commercialization of this commodity. The fast growing yeast Rhodosporidium toruloides NCYC 921 has been widely reported as a potential SCO producing yeast. In addition to its well-known high lipid content (that can be converted into biodiesel), is rich in high value added products such as carotenoids with commercial interest. The process design and integration may contribute to reduce the overall cost of biofuels and carotenoid production and is a mandatory step towards their commercialization. The present work addresses the biomass disruption, extraction, fractionation and recovery of products with special emphasis on high added valued carotenoids (beta-carotene, torulene, torularhodin) and fatty acids directed to biodiesel. The chemical structure of torularhodin with a terminal carboxylic group imposes an additional extra challenge in what concern its separation from fatty acids. The proposed feedstock is fresh biomass pellet obtained directly by centrifugation from a 5L fed-batch fermentation culture broth. The use of a wet instead of lyophilised biomass feedstock is a way to decrease processing energy costs and reduce downstream processing time. These results will contribute for a detailed process design. Gathered data will be of crucial importance for a further study on Life-Cycle Assessment (LCA).

Desenvolvimento de um relatório de suporte à declaração ambiental de produto: perfis de alumínio

A Avaliação do Ciclo de Vida (ACV) considera todo o ciclo de vida do produto, desde a extração e obtenção da matérias-primas, passando pela produção e fabrico de materiais e energia, até ao tratamento de fim de vida e destino final do produto. As Declarações Ambientais de Produto (DAP) são declarações ambientais Tipo III que apresentam um conjunto de informação quantificada e fidedigna, que funciona como uma excelente ferramenta de comunicação relativa ao desempenho ambiental do produto ao longo do seu ciclo de vida. Este relatório de estágio visa, por um lado, analisar os impactes ambientais no decurso do processo de produção do perfil de alumínio sujeito ao tratamento acetinado 20 natural (AC20NA) e, por outro, elaborar um relatório de suporte, que servirá de base para o desenvolvimento da DAP do perfil de alumínio AC20NA a submeter ao sistema DAPHabitat. O relatório foi elaborado tendo por base a norma EN 15804 e inclui as fases obrigatórias (A1-A3). Desta forma, utilizou-se ao software SimaPro para a análise dos impactes ambientais das várias fases do processo de fabrico do perfil de alumínio em estudo. As fases consideradas foram a extrusão, a anodização (tratamento de superfície), a Estação de Tratamento de águas Residuais Industriais (ETARI) e a embalagem. A fase que mais contribui para as diferentes categorias de impacte é a extrusão, uma vez que é nesta fase que é utilizada a matéria-prima para a produção dos perfis de aluminío.

Avaliação de Ciclo de Vida Energético (ACVE) de sistemas de vedação de habitações

Tese (doutorado)—Universidade de Brasília, Faculdade de Tecnologia, Departamento de Engenharia Civil e Ambiental, 2015.