Field and Laboratory Evaluation of Precast Concrete Bridges, TR-440, 2001

Recent data compiled by the National Bridge Inventory revealed 29% of Iowa's approximate 24,600 bridges were either structurally deficient or functionally obsolete. This large number of deficient bridges and the high cost of needed repairs create unique problems for Iowa and many other states. The research objective of this project was to determine the load capacity of a particular type of deteriorating bridge – the precast concrete deck bridge – which is commonly found on Iowa's secondary roads. The number of these precast concrete structures requiring load postings and/or replacement can be significantly reduced if the deteriorated structures are found to have adequate load capacity or can be reliably evaluated. Approximately 600 precast concrete deck bridges (PCDBs) exist in Iowa. A typical PCDB span is 19 to 36 ft long and consists of eight to ten simply supported precast panels. Bolts and either a pipe shear key or a grouted shear key are used to join adjacent panels. The panels resemble a steel channel in cross-section; the web is orientated horizontally and forms the roadway deck and the legs act as shallow beams. The primary longitudinal reinforcing steel bundled in each of the legs frequently corrodes and causes longitudinal cracks in the concrete and spalling. The research team performed service load tests on four deteriorated PCDBs; two with shear keys in place and two without. Conventional strain gages were used to measure strains in both the steel and concrete, and transducers were used to measure vertical deflections. Based on the field results, it was determined that these bridges have sufficient lateral load distribution and adequate strength when shear keys are properly installed between adjacent panels. The measured lateral load distribution factors are larger than AASHTO values when shear keys were not installed. Since some of the reinforcement had hooks, deterioration of the reinforcement has a minimal affect on the service level performance of the bridges when there is minimal loss of cross-sectional area. Laboratory tests were performed on the PCDB panels obtained from three bridge replacement projects. Twelve deteriorated panels were loaded to failure in a four point bending arrangement. Although the panels had significant deflections prior to failure, the experimental capacity of eleven panels exceeded the theoretical capacity. Experimental capacity of the twelfth panel, an extremely distressed panel, was only slightly below the theoretical capacity. Service tests and an ultimate strength test were performed on a laboratory bridge model consisting of four joined panels to determine the effect of various shear connection configurations. These data were used to validate a PCDB finite element model that can provide more accurate live load distribution factors for use in rating calculations. Finally, a strengthening system was developed and tested for use in situations where one or more panels of an existing PCDB need strengthening.

Development of LRFD Design Procedures for Bridge Piles in Iowa – Field Testing of Steel H-Piles in Clay, Sand, and Mixed Soils and Data Analysis (Volume II), TR-583, 2011

In response to the mandate on Load and Resistance Factor Design (LRFD) implementations by the Federal Highway Administration (FHWA) on all new bridge projects initiated after October 1, 2007, the Iowa Highway Research Board (IHRB) sponsored these research projects to develop regional LRFD recommendations. The LRFD development was performed using the Iowa Department of Transportation (DOT) Pile Load Test database (PILOT). To increase the data points for LRFD development, develop LRFD recommendations for dynamic methods, and validate the results of LRFD calibration, 10 full-scale field tests on the most commonly used steel H-piles (e.g., HP 10 x 42) were conducted throughout Iowa. Detailed in situ soil investigations were carried out, push-in pressure cells were installed, and laboratory soil tests were performed. Pile responses during driving, at the end of driving (EOD), and at re-strikes were monitored using the Pile Driving Analyzer (PDA), following with the CAse Pile Wave Analysis Program (CAPWAP) analysis. The hammer blow counts were recorded for Wave Equation Analysis Program (WEAP) and dynamic formulas. Static load tests (SLTs) were performed and the pile capacities were determined based on the Davisson’s criteria. The extensive experimental research studies generated important data for analytical and computational investigations. The SLT measured load-displacements were compared with the simulated results obtained using a model of the TZPILE program and using the modified borehole shear test method. Two analytical pile setup quantification methods, in terms of soil properties, were developed and validated. A new calibration procedure was developed to incorporate pile setup into LRFD.

Vitamin B12 Deficiency in the aged: Laboratory Diagnosis, Prevalence and Clinical Profile

B₁₂-vitamiinin puute iäkkäillä: laboratoriodiagnostiikka, yleisyys ja yhteys sairastavuuteen Tausta: B12-vitamiinin puute on yleistä iäkkäillä ja se tulisi todeta riittävän varhaisessa vaiheessa palautumattomien vaurioiden estämiseksi. On epäselvää pitäisikö diagnostiikka kohdistaa tiettyihin riskiryhmiin vai mahdollisesti seuloa valikoimatonta vanhusväestöä. Myöskään yksimielisyyttä laboratoriotutkimusten valinnasta ei ole. Tavoitteet: Tutkimuksen tarkoituksena oli evaluoida uutta HoloTC RIA menetelmää ja tuottaa viitearvot sille, selvittää B12-vitamiinin puutteen yleisyys, yhteys sairastavuuteen ja mahdolliset riskitekijät suomalaisessa vanhusväestössä, arvioida munuaisfunktion vaikusta B12-vitamiinin puutteen laboratoriotutkimuksiin ja näiden perusteella ehdottaa suomalaiseen terveydenhuoltoon sopivaa laboratoriotutkimusstrategiaa. Aineisto ja menetelmät: Liedon iäkkäät -tutkimuksen vanhusaineisto on edustava otos yhden kunnan yli 65-vuotiaasta väestöstä, yhteensä 1260 henkilöä. Tutkittavat kävivät lääkärintarkastuksessa, ja heistä on käytettävissä runsaasti laboratoriotutkimuksia sekä tiedot sairauksista, ruokavaliosta, lääkkeiden ja vitamiinivalmisteiden käytöstä, dementiaseula ja depressiokysely. Viitearvoaineistoa varten kerättiin näytteet 84 vapaaehtoisesta terveestä aikuisesta ja menetelmäevaluaatiota varten 107 sairaalapotilaasta. Tulokset: HoloTC RIA menetelmän toistettavuus oli hyvä manuaalimenetelmäksi. 95%:n viiteväli holotranskobalamiinille oli 37-171 pmol/l. Kaikilla tutkittavilla, joilla oli muilla laboratoriotutkimuksilla osoitettu todennäköinen B12-vitamiinin puute, myös holotranskobalamiini oli viitealueen alarajaa pienempi. Suurentuneella kystatiini C-pitoisuudella osoitettu munuaisten vajaatoiminta korreloi voimakkaasti homokysteiinin (rs=0.53, p<0.001) ja metyylimalonihapon (rs=0.27, p<0.001) pitoisuuksiin, mutta ei kokonais-B12-vitamiinin (rs=- 0.04, p=0.227) tai holotranskobamiinin (rs=-0.01, p=0.817) pitoisuuksiin. Suomalaisessa vanhusväestössä B12-vitamiinin puutteen prevalenssi oli 12%. Kokonais- B12-vitamiinin pitoisuus oli matala (<150 pmol/l) 6%:lla. Miessukupuoli (OR 1.9, 95% CI 1.2-2.9), ikä ≥75 (OR 2.2, 95% CI 1.4-3.4) ja maitotuotteiden välttäminen (OR 2.3, 95% CI 1.2-4.4) lisäsivät B12-vitamiinin puutteen riskiä, mutta anemia (OR 1.3, 95% CI 0.7-2.3) tai makrosytoosi (OR 1.2, 95% CI 0.6-2.7) eivät. Päätelmät: Diagnosoimaton B12-vitamiinin puute on yleistä iäkkäillä, mutta kliinisesti merkityksellistä spesifistä riskiryhmää ei löydy. Koska anemian ja makrosytoosin puuttuminen ei poissulje B12-vitamiinin puutetta ja munuaisten vajaatoiminta heikentää metabolisten merkkiaineiden käyttökelpoisuutta, kokonais-B12-vitamiinia suositellaan ensisijaiseksi laboratoriotutkimukseksi epäiltäessä B12-vitamiinin puutetta ja tarvittaessa varmentavina tutkimuksina käytetään homokysteiiniä ja holotranskobalamiinia.

Cellules gliales et douleur chronique: du laboratoire a l'espoir clinique [Glial cells and chronic pain: from the laboratory to clinical hope].

Despite their high prevalence, associated disability and seemingly rich pharmacopeia, the various forms of chronic pain remain frequently intractable. The past decade witnessed the rise of a concept stating that non-neuronal cells of the central nervous system, astrocytes and microglia, are crucial elements in pathological pain. This review gathers and summarizes the experimental data underpinning this theory in animal models and addresses their pertinence in humans. The potential opportunities and constraints of glial inhibition are exposed and compared to more moderate strategies of selective modulation. This therapeutic hope is particularly highlighted in our discussion of the first completed clinical trials employing glial inhibitors in the treatment of chronic pain.

Development of data sheets for statistical evaluation of fatigue data

To enable a mathematically and physically sound execution of the fatigue test and a correct interpretation of its results, statistical evaluation methods are used to assist in the analysis of fatigue testing data. The main objective of this work is to develop step-by-stepinstructions for statistical analysis of the laboratory fatigue data. The scopeof this project is to provide practical cases about answering the several questions raised in the treatment of test data with application of the methods and formulae in the document IIW-XIII-2138-06 (Best Practice Guide on the Statistical Analysis of Fatigue Data). Generally, the questions in the data sheets involve some aspects: estimation of necessary sample size, verification of the statistical equivalence of the collated sets of data, and determination of characteristic curves in different cases. The series of comprehensive examples which are given in this thesis serve as a demonstration of the various statistical methods to develop a sound procedure to create reliable calculation rules for the fatigue analysis.

Standardisation of elemental analytical techniques applied to provenance studies of archaeological ceramics: an inter laboratory calibration study

Chemical analysis is a well-established procedure for the provenancing of archaeological ceramics. Various analytical techniques are routinely used and large amounts of data have been accumulated so far in data banks. However, in order to exchange results obtained by different laboratories, the respective analytical procedures need to be tested in terms of their inter-comparability. In this study, the schemes of analysis used in four laboratories that are involved in archaeological pottery studies on a routine basis were compared. The techniques investigated were neutron activation analysis (NAA), X-ray fluorescence analysis (XRF), inductively coupled plasma optical emission spectrometry (ICP-OES) and inductively coupled plasma mass spectrometry (ICP-MS). For this comparison series of measurements on different geological standard reference materials (SRM) were carried out and the results were statistically evaluated. An attempt was also made towards the establishment of calibration factors between pairs of analytical setups in order to smooth the systematic differences among the results.

Learning analytics in practice: setting up a laboratory for action research at the Universitat Oberta de Catalunya

Since its inception in 1994 as a purely online university, the Universitat Oberta de Catalunya(UOC) has been able to position itself among the main universities of the Catalan and Spanish university systems. Most of the students at the UOC (currently more than 60,000) are adults who have a profile that could hardly fit into the traditional university system, thus finding in the UOC an opportunity to start or continue their higher education grades, in a very innovative environment. The intensive use of ICT for both theteaching/learning processes and management allowsresearchers and practitioners to obtain data aboutwhat takes place in the UOC Virtual Campus, which is continuously being improved according to suchfindings.

Els entorns virtuals d'aprenentatge com escenari Big Data: el cas de la UOC

En aquest treball es presenta el laboratori que l'eLearn Center posa a disposició del professorat i investigadors en e-learning de la UOC per al disseny sistemàtic d'experiments sota una perspectiva de Learning Analytics, però tambémecanismes per fer seguiment i documentar tot el procés que envolta el disseny d'experiències docents de forma que sigui més senzill transferir-les a altres àmbits.

Validation of plant dynamic model by online and laboratory measurements – a tool to predict online COD loads out of production of mechanical printing papers

COD discharges out of processes have increased in line with elevating brightness demands for mechanical pulp and papers. The share of lignin-like substances in COD discharges is on average 75%. In this thesis, a plant dynamic model was created and validated as a means to predict COD loading and discharges out of a mill. The assays were carried out in one paper mill integrate producing mechanical printing papers. The objective in the modeling of plant dynamics was to predict day averages of COD load and discharges out of mills. This means that online data, like 1) the level of large storage towers of pulp and white water 2) pulp dosages, 3) production rates and 4) internal white water flows and discharges were used to create transients into the balances of solids and white water, referred to as “plant dynamics”. A conversion coefficient was verified between TOC and COD. The conversion coefficient was used for predicting the flows from TOC to COD to the waste water treatment plant. The COD load was modeled with similar uncertainty as in reference TOC sampling. The water balance of waste water treatment was validated by the reference concentration of COD. The difference of COD predictions against references was within the same deviation of TOC-predictions. The modeled yield losses and retention values of TOC in pulping and bleaching processes and the modeled fixing of colloidal TOC to solids between the pulping plant and the aeration basin in the waste water treatment plant were similar to references presented in literature. The valid water balances of the waste water treatment plant and the reduction model of lignin-like substances produced a valid prediction of COD discharges out of the mill. A 30% increase in the release of lignin-like substances in the form of production problems was observed in pulping and bleaching processes. The same increase was observed in COD discharges out of waste water treatment. In the prediction of annual COD discharge, it was noticed that the reduction of lignin has a wide deviation from year to year and from one mill to another. This made it difficult to compare the parameters of COD discharges validated in plant dynamic simulation with another mill producing mechanical printing papers. However, a trend of moving from unbleached towards high-brightness TMP in COD discharges was valid.

Trigger and data link system for CMS Resistive Plate Chambers at the LHC accelerator

The purpose of the work was to realize a high-speed digital data transfer system for RPC muon chambers in the CMS experiment on CERN’s new LHC accelerator. This large scale system took many years and many stages of prototyping to develop, and required the participation of tens of people. The system interfaces to Frontend Boards (FEB) at the 200,000-channel detector and to the trigger and readout electronics in the control room of the experiment. The distance between these two is about 80 metres and the speed required for the optic links was pushing the limits of available technology when the project was started. Here, as in many other aspects of the design, it was assumed that the features of readily available commercial components would develop in the course of the design work, just as they did. By choosing a high speed it was possible to multiplex the data from some the chambers into the same fibres to reduce the number of links needed. Further reduction was achieved by employing zero suppression and data compression, and a total of only 660 optical links were needed. Another requirement, which conflicted somewhat with choosing the components a late as possible was that the design needed to be radiation tolerant to an ionizing dose of 100 Gy and to a have a moderate tolerance to Single Event Effects (SEEs). This required some radiation test campaigns, and eventually led to ASICs being chosen for some of the critical parts. The system was made to be as reconfigurable as possible. The reconfiguration needs to be done from a distance as the electronics is not accessible except for some short and rare service breaks once the accelerator starts running. Therefore reconfigurable logic is extensively used, and the firmware development for the FPGAs constituted a sizable part of the work. Some special techniques needed to be used there too, to achieve the required radiation tolerance. The system has been demonstrated to work in several laboratory and beam tests, and now we are waiting to see it in action when the LHC will start running in the autumn 2008.

Laboratory projects using inquiry-based learning: an application to a practical inorganic course

This paper reports how laboratory projects (LP) coupled to inquiry-based learning (IBL) were implemented in a practical inorganic chemistry course. Several coordination compounds have been successfully synthesised by students according to the proposed topics by the LP-IBL junction, and the chemistry of a number of metals has been studied. Qualitative data were collected from written reports, oral presentations, lab-notebook reviews and personal discussions with the students through an experimental course with undergraduate second-year students at the Universidad Nacional de Colombia during the last 5 years. Positive skills production was observed by combining LP and IBL. Conceptual, practical, interpretational, constructional (questions, explanations, hypotheses), communicational, environmental and application abilities were revealed by the students throughout the experimental course.

Combined experimental powder X-ray diffraction and DFT data to obtain the lowest energy molecular conformation of friedelin

Friedelin molecular conformers were obtained by Density Functional Theory (DFT) and by ab initio structure determination from powder X-ray diffraction. Their conformers with the five rings in chair-chair-chair-boat-boat, and with all rings in chair, are energy degenerated in gas-phase according to DFT results. The powder diffraction data reveals that rings A, B and C of friedelin are in chair, and rings D and E in boat-boat, conformation. The high correlation values among powder diffraction data, DFT and reported single-crystal data indicate that the use of conventional X-ray diffractometer can be applied in routine laboratory analysis in the absence of a single-crystal diffractometer.

A study of combustion phenomena in circulating fluidized beds by developing and applying experimental and modelling methods for laboratory-scale reactors

The results shown in this thesis are based on selected publications of the 2000s decade. The work was carried out in several national and EC funded public research projects and in close cooperation with industrial partners. The main objective of the thesis was to study and quantify the most important phenomena of circulating fluidized bed combustors by developing and applying proper experimental and modelling methods using laboratory scale equipments. An understanding of the phenomena plays an essential role in the development of combustion and emission performance, and the availability and controls of CFB boilers. Experimental procedures to study fuel combustion behaviour under CFB conditions are presented in the thesis. Steady state and dynamic measurements under well controlled conditions were carried out to produce the data needed for the development of high efficiency, utility scale CFB technology. The importance of combustion control and furnace dynamics is emphasized when CFB boilers are scaled up with a once through steam cycle. Qualitative information on fuel combustion characteristics was obtained directly by comparing flue gas oxygen responses during the impulse change experiments with fuel feed. A one-dimensional, time dependent model was developed to analyse the measurement data Emission formation was studied combined with fuel combustion behaviour. Correlations were developed for NO, N2O, CO and char loading, as a function of temperature and oxygen concentration in the bed area. An online method to characterize char loading under CFB conditions was developed and validated with the pilot scale CFB tests. Finally, a new method to control air and fuel feeds in CFB combustion was introduced. The method is based on models and an analysis of the fluctuation of the flue gas oxygen concentration. The effect of high oxygen concentrations on fuel combustion behaviour was also studied to evaluate the potential of CFB boilers to apply oxygenfiring technology to CCS. In future studies, it will be necessary to go through the whole scale up chain from laboratory phenomena devices through pilot scale test rigs to large scale, commercial boilers in order to validate the applicability and scalability of the, results. This thesis shows the chain between the laboratory scale phenomena test rig (bench scale) and the CFB process test rig (pilot). CFB technology has been scaled up successfully from an industrial scale to a utility scale during the last decade. The work shown in the thesis, for its part, has supported the development by producing new detailed information on combustion under CFB conditions.