Um algoritmo para estimação de estado em alimentadores de distribuição de energia elétrica com base no método da soma de potências

Most algorithms for state estimation based on the classical model are just adequate for use in transmission networks. Few algorithms were developed specifically for distribution systems, probably because of the little amount of data available in real time. Most overhead feeders possess just current and voltage measurements at the middle voltage bus-bar at the substation. In this way, classical algorithms are of difficult implementation, even considering off-line acquired data as pseudo-measurements. However, the necessity of automating the operation of distribution networks, mainly in regard to the selectivity of protection systems, as well to implement possibilities of load transfer maneuvers, is changing the network planning policy. In this way, some equipments incorporating telemetry and command modules have been installed in order to improve operational features, and so increasing the amount of measurement data available in real-time in the System Operation Center (SOC). This encourages the development of a state estimator model, involving real-time information and pseudo-measurements of loads, that are built from typical power factors and utilization factors (demand factors) of distribution transformers. This work reports about the development of a new state estimation method, specific for radial distribution systems. The main algorithm of the method is based on the power summation load flow. The estimation is carried out piecewise, section by section of the feeder, going from the substation to the terminal nodes. For each section, a measurement model is built, resulting in a nonlinear overdetermined equations set, whose solution is achieved by the Gaussian normal equation. The estimated variables of a section are used as pseudo-measurements for the next section. In general, a measurement set for a generic section consists of pseudo-measurements of power flows and nodal voltages obtained from the previous section or measurements in real-time, if they exist -, besides pseudomeasurements of injected powers for the power summations, whose functions are the load flow equations, assuming that the network can be represented by its single-phase equivalent. The great advantage of the algorithm is its simplicity and low computational effort. Moreover, the algorithm is very efficient, in regard to the accuracy of the estimated values. Besides the power summation state estimator, this work shows how other algorithms could be adapted to provide state estimation of middle voltage substations and networks, namely Schweppes method and an algorithm based on current proportionality, that is usually adopted for network planning tasks. Both estimators were implemented not only as alternatives for the proposed method, but also looking for getting results that give support for its validation. Once in most cases no power measurement is performed at beginning of the feeder and this is required for implementing the power summation estimations method, a new algorithm for estimating the network variables at the middle voltage bus-bar was also developed

Uso de técnicas de otimização baseadas em derivadas como suporte do planejamento operacional de redes de distribuição de energia elétrica

The usual programs for load flow calculation were in general developped aiming the simulation of electric energy transmission, subtransmission and distribution systems. However, the mathematical methods and algorithms used by the formulations were based, in majority, just on the characteristics of the transmittion systems, which were the main concern focus of engineers and researchers. Though, the physical characteristics of these systems are quite different from the distribution ones. In the transmission systems, the voltage levels are high and the lines are generally very long. These aspects contribute the capacitive and inductive effects that appear in the system to have a considerable influence in the values of the interest quantities, reason why they should be taken into consideration. Still in the transmission systems, the loads have a macro nature, as for example, cities, neiborhoods, or big industries. These loads are, generally, practically balanced, what reduces the necessity of utilization of three-phase methodology for the load flow calculation. Distribution systems, on the other hand, present different characteristics: the voltage levels are small in comparison to the transmission ones. This almost annul the capacitive effects of the lines. The loads are, in this case, transformers, in whose secondaries are connected small consumers, in a sort of times, mono-phase ones, so that the probability of finding an unbalanced circuit is high. This way, the utilization of three-phase methodologies assumes an important dimension. Besides, equipments like voltage regulators, that use simultaneously the concepts of phase and line voltage in their functioning, need a three-phase methodology, in order to allow the simulation of their real behavior. For the exposed reasons, initially was developped, in the scope of this work, a method for three-phase load flow calculation in order to simulate the steady-state behaviour of distribution systems. Aiming to achieve this goal, the Power Summation Algorithm was used, as a base for developping the three phase method. This algorithm was already widely tested and approved by researchers and engineers in the simulation of radial electric energy distribution systems, mainly for single-phase representation. By our formulation, lines are modeled in three-phase circuits, considering the magnetic coupling between the phases; but the earth effect is considered through the Carson reduction. Its important to point out that, in spite of the loads being normally connected to the transformers secondaries, was considered the hypothesis of existence of star or delta loads connected to the primary circuit. To perform the simulation of voltage regulators, a new model was utilized, allowing the simulation of various types of configurations, according to their real functioning. Finally, was considered the possibility of representation of switches with current measuring in various points of the feeder. The loads are adjusted during the iteractive process, in order to match the current in each switch, converging to the measured value specified by the input data. In a second stage of the work, sensibility parameters were derived taking as base the described load flow, with the objective of suporting further optimization processes. This parameters are found by calculating of the partial derivatives of a variable in respect to another, in general, voltages, losses and reactive powers. After describing the calculation of the sensibility parameters, the Gradient Method was presented, using these parameters to optimize an objective function, that will be defined for each type of study. The first one refers to the reduction of technical losses in a medium voltage feeder, through the installation of capacitor banks; the second one refers to the problem of correction of voltage profile, through the instalation of capacitor banks or voltage regulators. In case of the losses reduction will be considered, as objective function, the sum of the losses in all the parts of the system. To the correction of the voltage profile, the objective function will be the sum of the square voltage deviations in each node, in respect to the rated voltage. In the end of the work, results of application of the described methods in some feeders are presented, aiming to give insight about their performance and acuity

Análise e projeto de superfícies seletivas de frequência com elementos pré-fractais para aplicações em comunicações indoor

In this thesis, a frequency selective surface (FSS) consists of a two-dimensional periodic structure mounted on a dielectric substrate, which is capable of selecting signals in one or more frequency bands of interest. In search of better performance, more compact dimensions, low cost manufacturing, among other characteristics, these periodic structures have been continually optimized over time. Due to its spectral characteristics, which are similar to band-stop or band-pass filters, the FSSs have been studied and used in several applications for more than four decades. The design of an FSS with a periodic structure composed by pre-fractal elements facilitates the tuning of these spatial filters and the adjustment of its electromagnetic parameters, enabling a compact design which generally has a stable frequency response and superior performance relative to its euclidean counterpart. The unique properties of geometric fractals have shown to be useful, mainly in the production of antennas and frequency selective surfaces, enabling innovative solutions and commercial applications in microwave range. In recent applications, the FSSs modify the indoor propagation environments (emerging concept called wireless building ). In this context, the use of pre-fractal elements has also shown promising results, allowing a more effective filtering of more than one frequency band with a single-layer structure. This thesis approaches the design of FSSs using pre-fractal elements based on Vicsek, Peano and teragons geometries, which act as band-stop spatial filters. The transmission properties of the periodic surfaces are analyzed to design compact and efficient devices with stable frequency responses, applicable to microwave frequency range and suitable for use in indoor communications. The results are discussed in terms of the electromagnetic effect resulting from the variation of parameters such as: fractal iteration number (or fractal level), scale factor, fractal dimension and periodicity of FSS, according the pre-fractal element applied on the surface. The analysis of the fractal dimension s influence on the resonant properties of a FSS is a new contribution in relation to researches about microwave devices that use fractal geometry. Due to its own characteristics and the geometric shape of the Peano pre-fractal elements, the reconfiguration possibility of these structures is also investigated and discussed. This thesis also approaches, the construction of efficient selective filters with new configurations of teragons pre-fractal patches, proposed to control the WLAN coverage in indoor environments by rejecting the signals in the bands of 2.4~2.5 GHz (IEEE 802.11 b) and 5.0~6.0 GHz (IEEE 802.11a). The FSSs are initially analyzed through simulations performed by commercial software s: Ansoft DesignerTM and HFSSTM. The fractal design methodology is validated by experimental characterization of the built prototypes, using alternatively, different measurement setups, with commercial horn antennas and microstrip monopoles fabricated for low cost measurements

Implementação de um algoritmo para a análise de curtos-circuitos de alta impedância baseado no fluxo de carga soma de potências

This work has as main objective to show all the particularities regarding the Three-phase Power Summation Method, used for load flow calculation, in what it says respect to the influence of the magnetic coupling among the phases, as well as to the losses presented in all the existent transformers in the feeder to be analyzed. Besides, its application is detailed in the study of the short-circuits, that happen in the presence of high impedance values, which possess a problem, that is its difficult detection and consequent elimination on the part of common devices of protection. That happens due to the characteristic presented by the current of short¬ circuit, in being generally of the same order of greatness that the load currents. Results of simulations accomplished in several situations will be shown, objectifying a complete analysis of the behavior of the proposed method in several types of short-circuits. Confront of the results obtained by the method with results of another works will be presented to verify its effectiveness

Desenvolvimento de um protótipo para alimentação de pós para aspersão térmica em tocha de plasma

The nanometric powders have special features that usually result in new properties, originating applications or expanding them in various fields of knowledge. Because having a high area/volume ratio, phenomena such as superficial strength of adsorption becomes greater than the weight of the powder which makes more difficult its handling. The high power of agglomeration of these powders requires study and development of equipments to enable its management into the plasma torch. The objective of this work is to develop a powder feeder which can solve the mainly problems about insertion of powder into the thermal spray developed in the laboratory of plasmas, which are carried out with plasma torch arc not transferred (plasma spray). Therefore, it was made a aluminum s powder feeder and tests were performed to verify their operation and determine its rate of deposition by spraying powders of niobium pentoxide (Nb2O5) and titanium dioxide (TiO2) with particle sizes less than 250 mesh (<0.063 mm). We used masses of 0.5 g - 1.0 g and 1.5 g of each powder in tests lasting 15 seconds - 20 to 25 seconds for each mass. The tests were performed in two ways: at atmospheric pressure using argon gas with a flow of 9 l / min as carrier gas and through a Venturi pipe also using argon gas with a flow of 9 l / min as carrier gas and with a flow of 20 l/min as the feed gas passing through the Venturi pipe. The powder feeder developed in this paper is very easy to be handling and building, resulting in feeding rate of 0.25 cm3/min - 1.37 cm3/min. The TiO2 showed higher feeding rates than the Nb2O5 in all tests, and the best rates were obtained with tests using mass 1.5 g and time of 15 seconds, reaching feeding rate of 1.37 cm3/min. The flow of feed had low interference in feeding rate during the tests

Comunicar e interagir em novos espaços: o uso das mídias sociais no Sistema de Bibliotecas da UFRN

This study discusses about the practice of communication in libraries from the appropriation of the resources of web 2.0, particularly social media, establishing from the aspects of mediatization new communication scenarios in their environments. Aims at understanding how in the contemporary society, the libraries, that symbolize traditional space in the search for information and knowledge, modify their contexts through technological resources involved in your scenario, and specifically checks as the process of mediatization is inserted into the communication practices and interaction of libraries, noting the relevance of the ownership of social media, especially twitter and facebook, by the libraries of the Federal University of Rio Grande do Norte - UFRN. Use as methodological procedures, a theoretical approach concerning the conceptual research to investigate issues relating to social media, communication practice, mediatization and network society, and is characterized by being a descriptive exploratory research, of qualitative nature with adoption of the inductive method, using interviews and direct observation, analyzing reconfiguration scenario of university libraries located in UFRN. Thus, with the of the study, expected to be possible to give an overview of how to establish the use of social media in the scenario investigated by checking the new possibilities of communication, outreach services, information dissemination and interaction with user

Estratégia de vida do peixe anual Hypsolebias antenori (Cyprinodontiformes: Rivulidae) do semiárido brasileiro

This work deals with the life strategy of an endangered annual fish, Hypsolebias antenori (Cyprinodontiformes: Rivulidae), of the Brazilian semiarid region. The eggs of these fish hatch at the onset of the rainy season, grows rapidly and they reproduce during the rainy season. When the water puddles dry out, the entire population dies. The resistant eggs which are buried in the bottom of the dried pools go through diapause stages, during which time the embryonic development becomes temporarily arrested. With the onset of the next rainy season, the eggs hatch and a new generation is formed. Specimens of H. antenori were captured during 2011 and 2013, in temporary water pools located in the hydrographic basin of river Jaguaribe in Ceará, Brazil. Sex ratio, the length-weight relationship, the growth type, first sexual maturity, anatomy and histology of the digestive tract, development of gonads, reproductive strategy, karyotypic pattern of the species, and the conservation status of H. antenori were investigated. The results of this study are presented in the form of eight articles. The first article is about the fish faunal composition of the hydrographic basins of Rio Grande do Norte, Brazil, wherein the record of H. antenori is included. The second article deals with the sex ratio, secondary sexual characteristics of males, the length-weight relationship and the type of growth. Males show a pattern of intense coloration with well developed fins. The sex ratio showed a significant predominance of females (1M:1.7 F). Males were larger in length and weight. The equation of weight and total length relationship was Wt=0.0271Lt3,8937, showing a positively allometric growth, indicating greater increase in weight than in length. The third article discusses the anatomy and histology of the digestive tract of H. antenori. It is considered as a generalist feeder with characteristics of omnivore, which utilizes different food sources. The fourth article discusses the stages and phases of gonad development and type of spawning of H. antenori. The fifth article is about the r reproductive strategy adopted by H. antenori which helps in successful reproduction over a short period of life. The sixth article deals karyotypic pattern of the species, constituting the first cytogenetic contribution to the genus. The seventh article discusses about the risk of extinction of this species which suffers a series of threats, such as, habitat loss through land use, deforestation, construction of reservoirs, pollution due to domestic and industrial sewage, besides pesticides and agrochemicals. Furthermore, decreasing rainfall and intensification of aridity due to global climate changes, interferes with the reproductive cycle. The eighth article deals with aggressive behavior adopted between males and among females during reproduction. All temporary water pools sampled during this study were in high degree of degradation, mainly due to human action. There is a great need for conservation measures to protect the populations of annual fish, including the creation of protected areas in the semiarid ephemeral aquatic environments of Brazil

Aprendizado espacial-temporal em um ambiente complexo sem restrição alimentar em ratos

Timeplace learning is the capacity of organisms to associate both space and time with a biological relevant stimulus such as food. Experiments are usually done with food restricted animals due to the belief that food system activation is necessary for timeplace learning. Another line of thought suggest that, in addition to food system activation, response cost should be increased to effectively allow timeplace discrimination. The purpose of this experiment was to test whether a complex environment, which presumably implied in a heightened response cost, would facilitate timeplace association in satiated rats using a highly palatable food as reward. Nine rats were trained in a timeplace task for 30 nonconsecutive days. A large experimental box (1x1m) divided in four compartments was used. To access each compartment the animal had to overcome a series of obstacles such as ramps, staircases and mazes. Two feeders localized in opposite compartments were rewarded with sunflower seeds in two daily sessions. One feeder offered the reward during the morning sessions while the second feeder in afternoon sessions. After the 15th day of training, the animals began to show a preference for the correct feeder during the correct time of day expressed by increased frequency of visits as well as lower latency to access the feeders. These results suggest that satiated animals are also capable of learning a timespace task as far as the experimental context is complex enough to result in a higher response cost

Allocation of protective devices in distribution circuits using nonlinear programming models and genetic algorithms

The optimized allocation of protective devices in strategic points of the circuit improves the quality of the energy supply and the system reliability index. This paper presents a nonlinear integer programming (NLIP) model with binary variables, to deal with the problem of protective device allocation in the main feeder and all branches of an overhead distribution circuit, to improve the reliability index and to provide customers with service of high quality and reliability. The constraints considered in the problem take into account technical and economical limitations, such as coordination problems of serial protective devices, available equipment, the importance of the feeder and the circuit topology. The use of genetic algorithms (GAs) is proposed to solve this problem, using a binary representation that does (1) or does not (0) show allocation of protective devices (reclosers, sectionalizers and fuses) in predefined points of the circuit. Results are presented for a real circuit (134 busses), with the possibility of protective device allocation in 29 points. Also the ability of the algorithm in finding good solutions while improving significantly the indicators of reliability is shown. (C) 2003 Elsevier B.V. All rights reserved.

Algoritmos evolutivos dedicados à reconfiguração de redes radiais de distribuição sob demandas fixas e variáveis: estudo dos operadores genéticos e parâmetros de controle

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Terceiro setor em HIV/AIDS: mapeando o ativismo social na contemporaneidade

The struggle against AIDS is a kind of action in favor of life and the organized Brazilian civil society incorporated it in a meaningful dimension. This struggle matured the creation of non-governmental organizations (NGOs) and advanced with the discoveries about the disease. Since the very early 90 s, the consolidation of the partnership involving the movement anti-aids with State came up with a dilemma for the entities of civil society: are they just executors of governmental policies or do they take up the role of effective demands concerning public policies? Since then, activism against aids started to stand for execution of projects and one considers that the institutional way of anti-aids work has problems because it constructs a basic strategy to take off the political aspect of the third sector. The NGOs/aids consolidate the reconfiguration of capital and get far from street activities. This is important to be studied because the relationship between society and aids, contemporarily, can prevent them from accomplishing their agenda referring to political mobilization and collective resistance. This research started to be carried after some visits, previously arranged, to an institutional life support group called Grupo de Apoio à Vida-GAV, in Campina Grande. A semi-structured interview was applied to 31 users and to 6 technicians of the entity mentioned. One aimed at investigating the activist anti-aids practice, identifying the conceptions of activism and knowing how social actors assess those practices. Preliminary results indicate that one of the conceptions on activism among the interviewees refers to the execution of projects through partnership of NGOs and supporting institutions, governmental or non-governmental. Although this new conception on activism consolidates a non-political aspect, there are other ways of executing projects and participating actively, according to some users, such as: meetings, lectures and other sorts of events promoted by the group, which are also legitimate actions representing anti-aids activism at the present context

Detection and classification of voltage disturbances using a Fuzzy-ARTMAP-wavelet network

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Optimised placement of control and protective devices in electric distribution systems through reactive tabu search algorithm

Optimised placement of control and protective devices in distribution networks allows for a better operation and improvement of the reliability indices of the system. Control devices (used to reconfigure the feeders) are placed in distribution networks to obtain an optimal operation strategy to facilitate power supply restoration in the case of a contingency. Protective devices (used to isolate faults) are placed in distribution systems to improve the reliability and continuity of the power supply, significantly reducing the impacts that a fault can have in terms of customer outages, and the time needed for fault location and system restoration. This paper presents a novel technique to optimally place both control and protective devices in the same optimisation process on radial distribution feeders. The problem is modelled through mixed integer non-linear programming (MINLP) with real and binary variables. The reactive tabu search algorithm (RTS) is proposed to solve this problem. Results and optimised strategies for placing control and protective devices considering a practical feeder are presented. (c) 2007 Elsevier B.V. All rights reserved.

Robust fault diagnosis in power distribution systems based on fuzzy ARTMAP neural network-aided evidence theory

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Imposing Radiality Constraints in Distribution System Optimization Problems

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)