Formation of Fe-N films containing Fe6N2 phase by ion beam assisted deposition

Fe-N films were deposited on Si(100) and GaAs(100) substrates at room temperature by ion beam assisted deposition under various N/ Fe atomic arrival ratio, 0.09, 0.12, 0.15. The results of X-ray diffraction indicated that the film deposited at 0.12 of N/Fe arrival ratio contained a considerable fraction of the Fe16N2 phase which had grown predominantly in the [001] orientation. For the larger N/Fe arrival ratio, a martensite phase with 15 at.% nitrogen was obtained. It was found that a lower deposition temperature (<200 degrees C) was necessary for the formation of the Fe16N2 phase.

Formation and magnetic properties of Fe16N2 films prepared by ion-beam-assisted deposition

Fe-N films containing the Fe16N2 phase were prepared in a high-vacuum system of ion-beam-assisted deposition (IBAD). The composition and structure of the films were analysed by Auger electron spectroscopy (AES) and X-ray diffraction (XRD), respectively. Magnetic properties of the films were measured by a vibrating sample magnetometer (VSM). The phase composition of Fe-N films depend sensitively on the N/Fe atomic arrival ratio and the deposition temperature. An Fe16N2 film was deposited successfully on a GaAs (1 0 0) substrate by IBAD at a N/Fe atomic arrival ratio of 0.12. The gram-saturation magnetic moment of the Fe16N2 film obtained is 237 emu/g at room temperature, the possible cause has been analysed and discussed. Hysteresis loops of Fe16N2 have been measured, the coercive force H-c is about 120 Oe, which is much larger than the value for Fe, this means the Fe16N2 sample exhibits a large uniaxial magnetocrystalline anisotropy. (C) 1998 Elsevier Science B.V. All rights reserved.

A study of internal solitary waves observed on the continental shelf in the northwestern South China Sea

Based on in-situ time series data from the acoustic Doppler current profiler (ADCP) and thermistor chain in Wenchang area, a sequence of internal solitary wave (ISW) packets was observed in September 2005, propagating northwest on the continental shelf of the northwestern South China Sea (SCS). Corresponding to different stratification of the water column and tidal condition, both elevation and depression ISWs were observed at the same mooring location with amplitude of 35 m and 25 m respectively in different days. Regular arrival of the remarkable ISW packets at approximately the diurnal tidal period and the dominance of diurnal internal waves in the study area, strongly suggest that the main energy source of the waves is the diurnal tide. Notice that the wave packets were all riding on the troughs and shoulders of the internal tides, they were probably generated locally from the shelf break by the evolution of the internal tides due to nonlinear and dispersive effects.

基于TOA的无线传感器网络自定位技术的研究

提出一种基于TOA(tim e of arrival)测距、利用节点之间的几何关系实现传感器网络中未知节点自定位的算法.该方法计算量小、算法简单且定位精度高.仿真实验证明了该方法的有效性.*

随钻地震技术的研究及应用

Seismic While Drilling (SWD) is a new wellbore seismic technique. It uses the vibrations produced by a drill-bit while drilling as a downhole seismic energy source. The continuous signals generated by the drill bit are recorded by a pilot sensor attached to the top of the drill-string. Seismic wave receivers positioned in the earth near its surface receive the seismic waves both directly and reflection from the geologic formations. The pilot signal is cross-correlated with the receiver signals to compute travel-times of the arrivals (direct arrival and reflected arrival) and attenuate incoherent noise. No downhole intrusmentation is required to obtain the data and the data recording does not interfere with the drilling process. These characteristics offer a method by which borehole seismic data can be acquired, processed, and interpreted while drilling. As a Measure-While-Drill technique. SWD provides real-time seismic data for use at the well site . This can aid the engineer or driller by indicating the position of the drill-bit and providing a look at reflecting horizons yet to be encountered by the drill-bit. Furthermore, the ease with which surface receivers can be deployed makes multi-offset VSP economically feasible. First, this paper is theoretically studying drill-bit wavefield， interaction mode between drill-bit and formation below drill-bit , the new technique of modern signal process was applied to seismic data, the seismic body wave radiation pattern of a working roller-cone drill-bit can be characterized by theoretical modeling. Then , a systematical analysis about the drill-bit wave was done, time-distance equation of seismic wave traveling was established, the process of seismic while drilling was simulated using the computer software adaptive modeling of SWD was done . In order to spread this technique, I have made trial SWD modeling during drilling. the paper sketches out the procedure for trial SWD modeling during drilling , the involved instruments and their functions, and the trial effect. Subsurface condition ahead of the drill-bit can be predicted drillstring velocity was obtained by polit sensor autocorrelation. Reference decovolution, the drillstring multiples in the polit signal are removed by reference deconvolution, the crosscorrelation process enhance the signal-to-noise power ratio, lithologies. Final, SWD provides real-time seismic data for use at the well site well trajectory control exploratory well find out and preserve reservoirs. intervel velocity was computed by the traveltime The results of the interval velocity determination reflects the pore-pressure present in the subsurface units ahead of the drill-bit. the presences of fractures in subsurface formation was detected by shear wave. et al.

柴达木盆地地震勘探关键技术研究

The rugged surface topography determined the seismic data acquisition construction conditions and the seismic wave explosive and receiver quality in Qaidam Basin. This dissertation systematically researched the seismic acquisition, imaging process and the attribute analysis techniques of complicated oil and gas reservoir. The main research achievements and cognitions are as follows: 1. Through the stimulation effects research and analysis from the aspect of lithologic water-containing differences, it’s specific that stable hydrous sand layer can effectively enhance the stimulation effects combined with the corresponding field tests. The seismic data S/N ratio has been improved due to the combination explosive stimulation. Through the fold number and maximum offset analyses of target horizon, the complicated geometry has been optimized and the S/N ratio of seismic data has been improved, which made an important basis for improvement of 3D seismic data. 2. It has been proved that the first arrival refraction static correction method under the model constraint of fine surface survey is suitable to the Qaidam Basin of western areas by the real seismic data processing. Although the refraction horizon of near surface has some changes in a certain extent, it’s steady basically. The refraction horizon can be continuously traced in sections, so it’s qualified for the refraction static correction method on the whole. 3. The research is based on the curved-ray pre-stack time migration techniques of rough topography, and improved the imaging precision of complex areas. This techniques adopted the constant and variable velocity scanning mode and enhanced the velocity analysis precision. The 3D pre-stack time migration techniques reasonably solved the imaging and velocity multiple solutions problems of steep-dip faults and the intersections of horizontal layers. What’s more, fine velocity analysis and mute are very important to enhance the imaging precision of the seismic data in complicated Wunan areas. 4. The 3D seismic data edge-preserving processing methods have been realized due to the image process techniques. Because this method uses the large range filter, it can attenuate the noise maximally. The faults, break points, lithologic pinchout points and lithologic body of small scale such as river will not be influenced by blur because of the edge-preserving characterization of the method which is really an effective assistant technique of low S/N ratio seismic data attribute analysis. 5. The use of spectral decomposition technique can effectively identify the reservoirs. The special geology body which will not be identified (or without obvious characters) in the seismic profile may be found through the details changes of different frequencies in the amplitude profiles.

层析静校正技术研究和应用

Static correction is one of the indispensable steps in the conventional onshore seismic data processing, particularly in the western part of China; it is theoretically and practically significant to resolve the issue of static correction. Conventional refraction static correction is put forward under the assumption that layered medium is horizontal and evenly distributed. The complicated nature of the near surface from western part of China is far from the assumption. Therefore, the essential way to resolve the static correction problem from the complex area is to develop a new theory. In this paper, a high-precision non-linear first arrival tomography is applied to solve the problem, it moved beyond the conventional refraction algorithm based on the layered medium and can be used to modeling the complex near surface. Some of the new and creative work done is as follows: One. In the process of first arrival tomographic image modeling, a fast high-order step algorithm is used to calculate the travel time for first arrival and ray path and various factors concerning the fast step ray tracing algorithm is analyzed. Then the second-order and third-order differential format is applied to the step algorithm which greatly increased the calculation precision of the ray tracing and there is no constraint to the velocity distribution from the complex areas. This method has very strong adaptability and it can meet the needs of great velocity variation from the complicated areas. Based on the numerical calculation, a fast high-order step is a fast, non-conditional and stable high-precision tomographic modeling algorithm. Two, in the tomographic inversion, due to the uneven fold coverage and insufficient information, the inversion result is unstable and less reliable. In the paper, wavelet transform is applied to the tomographic inversion which has achieved a good result. Based on the result of the inversion from the real data, wavelet tomographic inversion has increased the reliability and stability of the inversion. Three. Apply the constrained high-precision wavelet tomographic image to the static correction processing from the complex area. During tomographic imaging, by using uphole survey, refraction shooting or other weathering layer method, weathering layer can be identified before the image. Because the group interval for the shot first arrival is relatively big, there is a lack of precision for the near surface inversion. In this paper, an inversion method of the layer constraint and well constraint is put forward, which can be used to compensate the shallow velocity of the inversion for the shot first arrival and increase the precision of the tomographic inversion. Key words: Tomography ，Fast marching method，Wavelet transform, Static corrections, First break

陆地三分量三维地震勘探技术研究与应用

With the development of oil and gas field exploration, it becomes harder to search new reserves. So a higher demand of seismic exploration comes up. Now 3C3D seismic exploration technology has been applied in petroleum exploration domains abroad. Comparing with the traditional P-wave exploration, the seismic attributes information which provided by 3C3D seismic exploration will increase quickly. And it can derive various combined parameters. The precision of information about lithology, porosity, fracture, oil-bearing properties, etc which estimated by above parameters was higher than that of pure P-wave exploration. These advantages mentioned above lead to fast development of 3C3D seismic technology recently. Therefore, how to apply the technology in petroleum exploration field in China, how to obtain high quality seismic data, and how to process and interpret real data, become frontier topics in geophysical field nowadays, which have important practical significance in research and application. In this paper, according to the propagation properties of P-wave and converted wave, a study of 3C3D acquisition parameters design method was completed. Main parameters included: trace interval, shot interval, maximum offset, bin size, the interval of receiving lines, the interval of shooting lines, migration aperture, maximum cross line distance, etc. Their determination principle was given. The type of 3C3D seismic exploration geometry was studied. By calculating bin attributes and analyzing parameters of geometry, some useful conclusions were drawn. With the method in this paper, real geometries for continental lithology stratum gas reservoir and fractured gas reservoir were studied and determined. In the static method of multi-wave, the near surface P-wave, S-wave parameter investigation method has been advanced, and this method has been applied for the patent successfully; the near surface P-wave, S-wave parameter investigation method and the converted refraction wave first arrival static techniques have been integrally used to improve the effectiveness of converted wave static. In the aspect of converted wave procession, the rotation of horizontal component data, the calculation of converted wave common conversion bin, the residual static of converted wave, the velocity analysis of the common conversion point (CCP), the Kirchhoff pre-stack time migration of converted wave techniques have been applied for setting up the various 3C3D seismic data processing flows based on different geologic targets, and the high quality P-wave, converted-wave profiles have been acquired in the actual data processing. In the aspect of P-wave and converted-wave comprehensive interpretation, the thoughts and methods of using zero-offset S-wave VSP data to calibrate horizon have been proposed; the method of using P-wave and S-wave amplitude ratio to predict the areas of oil and gas enrichment has been studied; the method of inversion using P-wave combined with S-wave has been studied; the various P-wave, S-wave parameters(velocity ratio, amplitude ratio, poisson ratio) have been used to predict the depth, physical properties, gas-bearing properties of reservoirs; the method of predicting the continental stratum lithology gas reservoir has been built. The above techniques have all been used in various 3D3C seismic exploration projects in China, and the better effects have been gotten. By using these techniques, the 3C3D seismic exploration level has been improved.

Pg震相走时的各向异性影响及各向异性结构成像

As the first arrival of seismic phase in deep seismic sounding, Pg is the important data for studying the attributes of the sedimentary layers and the shape of crystalline basement because of its high intensity and reliable detection. Conventionally, the sedimentary cover is expressed as isotropic, linear increasing model in the interpretation of Pg event. Actually, the sedimentary medium should be anisotropic as preferred cracks or fractures and thin layers are common features in the upper crust, so the interpretation of Pg event needs to be taken account of seismic velocity anisotropy. Traveltime calculation is the base of data processing and interpretation. Here, we only study the type of elliptical anisotropy for the poor quality and insufficiency of DSS data. In this thesis, we first investigate the meaning of elliptical anisotropy in the study of crustal structure and attribute, then derive Pg event’s traveltime-offset relationship by assuming a linear increasing velocity model with elliptical anisotropy and present the invert scheme from Pg traveltime-offset dataset to seismic velocity and its anisotropy of shallow crustal structure. We compare the Pg traveltime calculated by our analytic formula with numerical calculating method to test the accuracy. To get the lateral variation of elliptical anisotropy along the profiling, a tomography inversion method with the derived formula is presented, where the profile is divided into rectangles. Anisotropic imaging of crustal structure and attribute is efficient method for crust study. The imaging result can help us interprete the seismic data and discover the attribute of the rock to analyze the interaction between layers. Traveltime calculation is the base of image. Base on the ray tracing equations, the paper present a realization of three dimension of layer model with arbitrary anisotropic type and an example of Pg traveltime calculation in arbitrary anisotropic type is presented. The traveltime calculation method is complex and it only adapts to nonlinear inversion. Perturbation method of travel-time calculation in anisotropy is the linearization approach. It establishes the direct relation between seismic parameters and travetime and it is fit for inversion in anisotropic structural imaging. The thesis presents a P-wave imaging method of layer media for TTI. Southeastern China is an important part of the tectonic framework concerning the continental margin of eastern China and is commonly assumed to comprise the Yangtze block and the Cathaysia block, the two major tectonic units in the region. It’s a typical geological and geophysical zone. In this part, we fit the traveltime of Pg phase by the raytracing numerical method. But the method is not suitable here because the inefficiency of numerical method and the method itself. By the analytic method, we fit the Pg and Sg and get the lateral variation of elliptical anisotropy and then discuss its implication. The northeastern margin of Qinghai-Tibetan plateau is typical because it is the joint area of Eurasian plate and Indian plate and many strong earthquakes have occurred there in recent years．We use the Pg data to get elliptical anisotropic variation and discuss the possible meaning.

地震层析成像与天山地区的壳幔深部结构研究

The Tien Shan is the most prominent intracontinental mountain belt on the earth. The active crustal deformation and earthquake activities provide an excellent place to study the continental geodynamics of intracontinental mountain belt. The studies of deep structures in crust and upper mantle are significantly meaningful for understanding the geological evolution and geodynamics of global intracontinental mountain belts. This dissertation focuses on the deep structures and geodynamics in the crust and upper mantle in the Tien Shan mountain belt. With the arrival time data from permanent and temporal seismic stations located in the western and central Tien Shan, using seismic travel time tomographic method, we inversed the P-wave velocity and Vp/Vs structures in the crust and uppermost mantle, the Pn and Sn velocities and Pn anisotropic structures in the uppermost mantle, and the P-wave velocity structures in the crust and mantle deep to 690km depth beneath the Tien Shan. The tomographic results suggest that the deep structures and geodynamics have significant impacts not only on the deformations and earthquake activities in the crust, but also on the mountain building, collision, and dynamics of the whole Tien Shan mountain belt. With the strongly collision and deformations in the crust, the 3-D P-wave velocity and Vp/Vs ratio structures are highly complex. The Pn and Sn velocities in the uppermost mantle beneath the Tien Shan, specially beneath the central Tien Shan, are significantly lower than the seismic wavespeed beneath geological stable regions. We infer that the hot upper mantle from the small-scale convection could elevate the temperature in the lower crust and uppermost mantle, and partially melt the materials in the lower crust. The observations of low P-wave and S-wave velocities, high Vp/Vs ratios near the Moho and the absences of earthquake activities in the lower crust are consistent with this inference. Based on teleseismic tomography images of the upper mantle beneath the Tien Shan, we infer that the lithosphere beneath the Tarim basin has subducted under the Tien Shan to depths as great as 500 km. The lithosphere beneath the Kazakh shield may have subducted to similar depths in the opposite direction, but the limited resolution of this data set makes this inference less certain. These images support the plate boundary model of converge for the Tien Shan, as the lithospheres to the north and south of the range both appear to behave as plates.

华北及周边地区层析成像研究

Our study deals with the high resolution body wave tomography in North china and adjacent areas(30°N-43°N，100°E-130°E), where earthquakes occurred many times in history and has a very complicated geological structure. 6870 events recorded at 273 digital seismic stations from CDSN during 1996－2002 and stations settled by Seislab of IGCAS in Bohai Bay area, including 1382 local earthquakes and 5488 teleseismic earthquakes are used in this study. In the data we used, the average number of received stations is greater than 5, the error of picking up direct arrival time is 0.1－0.5s. Before the inversion, we use Checkerboard method to confirm the reliability of result of Local events; use Restoring Resolution Test to confirm the reliability of result of teleseismic events. We also analyzed the effect of different parameters in the inversion. Based the analysis above, the model used in this paper is divided into small blocks with a dimension of 0.33°in the latitude and longitude directions and 5km、15km、30km in depth, and initial velocity model. Using pseudobending method to calculate the ray traveling path, LSQR algorithm to inverse, finally, we got the body velocity images below 25km and above 480km in this area using Joint- inversion with local events and teleseismic events. We made the conclusion at last: (1)at top zone of the south of Sichuan Basin , there exits low velocity anomalies, below 40km is the high velocity zone extend to 300km; (2) Above the 40km of Ordos block exits low velocity zone, while below 40km until 240km, the high velocity anomalies are interlaced by low velocity anomalies. Below 300km, the anomalies are unclear any more; (3) On the whole, the velocity structure below 400km on the mantle transition zone of Eastern China area shows its changes from low velocity to high velocity.

井间地震速度层析成像方法与软件系统

Crosshole Seismic tomography has been broadly studied and applied in the fields of resource exploration and engineering exploration because of its special observing manner and better resolution than normal seismic exploration. This thesis will state the theory and method of Crosshole Seismic tomography. Basing on the previous studies，the thesis studied the initial velocity model，ray-tracing method, and developed the three-dimension tomography software. All the cells that a ray passes through are of the same velocities if the paths from transmitters to receivers are straight. The cells that the each ray passes through are recorded, and rays that pass through each cell are calculated. The ray average velocity which passes through a cell is set as the cell velocity. Analogously we can make a initial node velocity model because the velocity sum is calculated on the all cells which own to a certain node, and the cell number is summed about each nodes，the ratio of the velocity sum to the all cells number is set as the node velocity. The inversion result from the initial node velocity model is better than that of the average velocity model. Ray-bending and Shortest Path for Rays (SPR) have shortcomings and limitations respectively. Using crooked rays obtained from SPR rather than straight lines as the starting point can not only avoid ray bending converging to the local minimum travel time path, but also settle the no smooth ray problem obtained by SPR. The hybrid method costs much computation time, which is roughly equal to the time that SPR expends. The Delphi development tool based on the Object Pascal language standard has an advantage of object-oriented. TDTOM (Three Dimensions Tomography) was developed by using Delphi from the DOS version. Improvement on the part of inversion was made, which bring faster convergence velocity. TDTOM can be used to do velocity tomography from the first arrival travel time of the seismic wave, and it has the good qualities of friendly user interface and convenient operation. TDTOM is used to reconstruct the velocity image for a set of crosshole data from Karamay Oil Field. The geological explanation is then given by comparing the inversion effects of different ray-tracing methods. High velocity zones mean the cover of oil reservoir, and low velocity zones correspond to the reservoir or the steam flooding layer.

数据驱动型多次波衰减方法的研究

In the practical seismic profile multiple reflections tend to impede the task of even the experienced interpreter in deducing information from the reflection data. Surface multiples are usually much stronger, more broadband, and more of a problem than internal multiples because the reflection coefficient at the water surface is much larger than the reflection coefficients found in the subsurface. For this reason most attempts to remove multiples from marine data focus on surface multiples, as will I. A surface-related multiple attenuation method can be formulated as an iterative procedure. In this essay a fully data-driven approach which is called MPI —multiple prediction through inversion (Wang, 2003) is applied to a real marine seismic data example. This is a pretty promising scheme for predicting a relative accurate multiple model by updating the multiple model iteratively, as we usually do in a linearized inverse problem. The prominent characteristic of MPI method lie in that it eliminate the need for an explicit surface operator which means it can model the multiple wavefield without any knowledge of surface and subsurface structures even a source signature. Another key feature of this scheme is that it can predict multiples not only in time but also in phase and in amplitude domain. According to the real data experiments it is shown that this scheme for multiple prediction can be made very efficient if a good initial estimate of the multiple-free data set can be provided in the first iteration. In the other core step which is multiple subtraction we use an expanded multi-channel matching filter to fulfil this aim. Compared to a normal multichannel matching filter where an original seismic trace is matched by a group of multiple-model traces, in EMCM filter a seismic trace is matched by not only a group of the ordinary multiple-model traces but also their adjoints generated mathematically. The adjoints of a multiple-model trace include its first derivative, its Hilbert transform and the derivative of the Hilbert transform. The third chapter of the thesis is the application for the real data using the previous methods we put forward from which we can obviously find the effectivity and prospect of the value in use. For this specific case I have done three group experiments to test the effectiveness of MPI method, compare different subtraction results with fixed filter length but different window length, invest the influence of the initial subtraction result for MPI method. In terms of the real data application, we do fine that the initial demultiple estimate take on a great deal of influence for the MPI method. Then two approaches are introduced to refine the intial demultiple estimate which are first arrival and masking filter respectively. In the last part some conclusions are drawn in terms of the previous results I have got.

离散裂缝诱导各向异性粘弹性地震波模拟与特征分析

The real media always attenuate and distort seismic waves as they propagate in the earth. This behavior can be modeled with a viscoelastic and anisotropic wave equation. The real media can be described as fractured media. In this thesis, we present a high-order staggered grid finite-difference scheme for 2-D viscoelastic wave propagation in a medium containing a large number of small finite length fractures. We use the effective medium approach to compute the anisotropic parameters in each grid cell. By comparing our synthetic seismogram by staggered-grid finite-difference with that by complex-ray parameter ray tracing method, we conclude that the high-order staggered-grid finite-difference technique can effectively used to simulate seismic propagation in viscoelastic-anisotropic media. Synthetic seismograms demonstrate that strong attenuation and significant frequency dispersion due to viscosity are important factors of reducing amplitude and delaying arrival time varying with incidence angle or offset. On the other hand, the amount of scattered energy not only provides an indicator of orientation of fracture sets, but can also provide information about the fracture spacing. Analysis of synthetic seismograms from dry- and fluid-filled fractures indicates that dry-filled fractures show more significant scattering on seismic wavefields than fluid-filled ones, and offset-variations in P-wave amplitude are observable. We also analyze seismic response of an anticlinal trap model that includes a gas-filled fractured reservoir with high attenuation, which attenuates and distorts the so-called bright spot.

叠前深度偏移速度模型的建立方法研究

Seismic exploration is the main tools of exploration for petroleum. as the society needs more petroleum and the level of exploration is going up, the exploration in the area of complex geology construction is the main task in oil industry, so the seismic prestack depth migration appeared, it has good ability for complex construction imaging. Its result depends on the velocity model strongly. So for seismic prestack depth migration has become the main research area. In this thesis the difference in seismic prestack depth migration between our country and the abroad has been analyzed in system. the tomographical method with no layer velocity model, the residual curve velocity analysical method based on velocity model and the deleting method in pre-processing have been developed. In the thesis, the tomographysical method in velocity analysis is been analyzed at first. It characterized with perfection in theory and diffculity in application. This method use the picked first arrivial, compare the difference between the picked first arrival and the calculated arrival in theory velocity model, and then anti-projected the difference along the ray path to get the new velocity model. This method only has the hypothesis of high frequency, no other hypothesis. So it is very effective and has high efficiency. But this method has default still. The picking of first arrival is difficult in the prestack data. The reasons are the ratio of signal to noise is very low and many other event cross each other in prestack data. These phenomenon appear strongly in the complex geology construction area. Based on these a new tomophysical methos in velocity analysis with no layer velocity model is been developed. The aim is to solve the picking problem. It do not need picking the event time contiunely. You can picking in random depending on the reliability. This methos not only need the pick time as the routine tomographysical mehtod, but also the slope of event. In this methos we use the high slope analysis method to improve the precision of picking. In addition we also make research on the residual curve velocity analysis and find that its application is not good and the efficiency is low. The reasons is that the hypothesis is rigid and it is a local optimizing method, it can solve seismic velocity problem in the area with laterical strong velocity variation. A new method is developed to improve the precision of velocity model building . So far the pattern of seismic prestack depth migration is the same as it aborad. Before the work of velocity building the original seismic data must been corrected on a datum plane, and then to make the prestack depth migration work. As we know the successful example is in Mexico bay. It characterized with the simple surface layer construction, the pre-precessing is very simple and its precision is very high. But in our country the main seismic work is in land, the surface layer is very complex, in some area the error of pre-precessing is big, it affect the velocity building. So based on this a new method is developed to delete the per-precessing error and improve the precision of velocity model building. Our main work is, (1) developing a effective tomographical velocity building method with no layer velocity model. (2) a new high resolution slope analysis method is developed. (3) developing a global optimized residual curve velocity buliding method based on velocity model. (4) a effective method of deleting the pre-precessing error is developing. All the method as listed above has been ceritified by the theorical calculation and the actual seismic data.