Nonlinear description of transversal motion in a laminar boundary layer with streaks

The nonlinear streamwise growth of a spanwise periodic array of steady streaks in a flat plate boundary layer is numerically computed using the well known Reduced Navier- Stokes formulation. It is found that the flow configuration changes substantially when the amplitude of the streaks grows and the nonlinear effects come into play. The transversal motion (in the wall normal-spanwise plane), which is normally not considered, becomes non-negligible in the nonlinear regime, and it strongly distorts the streamwise velocity profiles, which end up being quite different from those predicted by the linear theory. We analyze in detail the resulting flow patterns for the nonlinearly saturated streaks, and compare them with available experimental results.

Low-Dimensional Modelling for optimal streaks in the blasius boundary layer

This paper is concerned with the low dimensional structure of optimal streaks in the Blasius boundary layer. Optimal streaks are well known to exhibit an approximate self-similarity, namely the streamwise velocity re-scaled with their maximum remains almost independent of both the spanwise wavenumber and the streamwise coordinate. However, the reason of this self-similar behavior is still unexplained as well as unexploited. After revisiting the structure of the streaks near the leading edge singularity, two additional approximately self-similar relations involving the velocity components and their wall normal derivatives are identified. Based on these properties, we derive a low dimensional model with two degrees of freedom. The comparison with the results obtained from the linearized boundary layer equations shows that this model is consistent and provide good approximations.

General Report on Main Session 4: Embankments and dams, slope stability and landslides

The General Reporter presents the papers from the Authors, along with some personal contributions on the subjects discussed. Embankments are classified by their use. Different kinds of slope failure and remedial measures are dealt with, as well as investigations for material characterisation and selection.

Modeling sub-threshold slope and DIBL mismatch of sub-22nm FinFet

A great challenge for future information technologies is building reliable systems on top of unreliable components. Parameters of modern and future technology devices are affected by severe levels of process variability and devices will degrade and even fail during the normal lifeDme of the chip due to aging mechanisms. These extreme levels of variability are caused by the high device miniaturizaDon and the random placement of individual atoms. Variability is considered a "red brick" by the InternaDonal Technology Roadmap for Semiconductors. The session is devoted to this topic presenDng research experiences from the Spanish Network on Variability called VARIABLES. In this session a talk entlited "Modeling sub-threshold slope and DIBL mismatch of sub-22nm FinFet" was presented.

A genetic algorithm for slope stability analyses with concave slip surfaces using custom operators

Heuristic methods are popular tools to find critical slip surfaces in slope stability analyses. A new genetic algorithm (GA) is proposed in this work that has a standard structure but a novel encoding and generation of individuals with custom-designed operators for mutation and crossover that produce kinematically feasible slip surfaces with a high probability. In addition, new indices to assess the efficiency of operators in their search for the minimum factor of safety (FS) are proposed. The proposed GA is applied to traditional benchmark examples from the literature, as well as to a new practical example. Results show that the proposed GA is reliable, flexible and robust: it provides good minimum FS estimates that are not very sensitive to the number of nodes and that are very similar for different replications

Vestibular navigation directed by the slope of terrain.

Slope of terrain is an important orienting gradient affecting the goal-directed locomotion of animals. Its significance was assessed in experiment 1 by training rats to find in darkness a feeder on the top of a low cone (80-cm base, 0- to 4-cm high). A computerized infrared tracking system monitoring the rat's position in darkness showed that the path length on the cone surface was inversely proportional to cone height. A device allowing continuous generation of slope-guided locomotion was used in experiment 2. This device consists of a 1-m arena, the floor of which can be supported at a point corresponding to the position of one of three equidistant feeders located 17 cm from its center. The arena is inclined by the locomotion of the rat to a plane passing through the elevated (2- or 4-cm) feeder, the rat's center of gravity, and a point at the edge of the arena resting on the floor. The multitude of such planes generated by the rat's locomotion forms the surface of a virtual cone, the top of which is formed by the feeder. Additional path (difference between distance traveled and shortest distance of the animal from the goal at the onset of inclination) is inversely related to the incline of the arena and is a sensitive measure of performance in this type of vestibular navigation.

Assessment of corrective measures for alleviating slope instabilities in carbonatic Flysch formations: Alicante (SE of Spain) case study

As is well known, in order to select remediation measures to correct or prevent slope instabilities, it is essential to identify and characterize the instability mechanisms. This task is especially complex for heterogeneous rock masses such as Flysch formations. This paper addresses the assessment of corrective measures used in carbonate Flysch formations by classifying and grouping field data reported in an available database in order to associate this data with various instability mechanisms and stratigraphic column types as well as with the corrective measures taken to stabilise them. For this purpose, 194 slopes have been geomechanically characterized, mainly by considering the observed instability mechanisms. The corrective measures that were applied have been evaluated for their suitability and performance, and, if applicable, the causes of their malfunction have been also studied. As a result, some guidelines based on the observed behaviour and the suitability of the correction measure as a function of instability type are proposed for similar slopes.

Characterization of rock slopes through slope mass rating using 3D point clouds

Rock mass classification systems are widely used tools for assessing the stability of rock slopes. Their calculation requires the prior quantification of several parameters during conventional fieldwork campaigns, such as the orientation of the discontinuity sets, the main properties of the existing discontinuities and the geo-mechanical characterization of the intact rock mass, which can be time-consuming and an often risky task. Conversely, the use of relatively new remote sensing data for modelling the rock mass surface by means of 3D point clouds is changing the current investigation strategies in different rock slope engineering applications. In this paper, the main practical issues affecting the application of Slope Mass Rating (SMR) for the characterization of rock slopes from 3D point clouds are reviewed, using three case studies from an end-user point of view. To this end, the SMR adjustment factors, which were calculated from different sources of information and processes, using the different softwares, are compared with those calculated using conventional fieldwork data. In the presented analysis, special attention is paid to the differences between the SMR indexes derived from the 3D point cloud and conventional field work approaches, the main factors that determine the quality of the data and some recognized practical issues. Finally, the reliability of Slope Mass Rating for the characterization of rocky slopes is highlighted.

The refugee crisis: Schengen’s slippery slope. EPC Commentary, 22 September 2015

While the European Union (EU) is facing one of the most divisive crises in its history, the pressure to take immediate action is enormous. Yet, negotiations in the Council have shown that the prospect of a common European response to the manifold effects and underlying reasons of the refugee crisis still belongs to the distant future. Only a few days after Commission President Jean-Claude Juncker delivered his State of the Union address – avowing that Schengen will not be abolished under his term – national decisions to reintroduce temporary border controls are multiplying. Germany, one of the most ardent defenders of a borderless Union, decided to temporarily reinstate border checks. Austria and Slovenia came next. Slovakia, the Czech Republic, Poland, the Netherlands and France might follow.