943 resultados para Non-traditional exports
Resumo:
In the present work, electroactive grain boundaries of highly dense metal oxide SnO2-based polycrystalline varistors were determined by electrostatic force microscopy (EFM). The EFM technique was applied to identify electroactive grain boundaries and thus estimate the amount of active grain boundary, which, in the metal oxide SnO2-based varistor, was calculated at around 85%, i.e., much higher than that found in traditional metal oxide ZnO-based varistors. The mean potential barrier height value obtained from the EFM analysis was in complete agreement with the values calculated from the C-V measurements, together with a complex capacitance plane analysis that validates the methodology proposed here. (c) 2006 American Institute of Physics.
Resumo:
An investigation was made into the non-Ohmic and dielectric properties of a Ca2Cu2Ti4O12 perovskite-type system. Compared to the traditional CaCu3Ti4O12-based composition, the imbalance between the Ca and Cu atoms caused the formation of a polycrystalline system presenting similar to 33.3 mol % of CaCu3Ti4O12 (traditional composition) and similar to 66.7 mol % of CaTiO3. As for non-Ohmic properties, the effect of this Ca and Cu atom imbalance was that a nonlinear electric behavior of similar to 1500 was obtained. This high nonlinear electrical behavior emerged in detriment to the ultrahigh dielectric property frequently reported. The high non-Ohmic property was explained by the existence of Schottky-type barriers, whose formation mechanism may be similar to that proposed for traditional metal oxide non-Ohmic devices, according to similarities discussed herein. (c) 2006 American Institute of Physics.
Resumo:
The present review describes mainly the history of SnO2-based voltage-dependent resistors, discusses the main characteristics of these polycrystalline semiconductor systems and includes a direct comparison with traditional ZnO-based voltage-dependent resistor systems to establish the differences and similarities, giving details of the basic physical principles involved with the non-ohmic properties in both polycrystalline systems. As an overview, the text also undertakes the main difficulties involved in processing SnO2- and ZnO-based non-ohmic systems, with an evaluation of the contribution of the dopants to the electronic properties and to the final microstructure and consequently to the system's non-ohmic behavior. However, since there are at least two review texts regarding ZnO-based systems [Levinson, L. M., and Philipp, H. R. Ceramic Bulletin 1985;64:639; Clarke, D. R. Journal of American Ceramic Society 1999;82:485], the main focus of the present text is dedicated to the SnO2-based varistor systems, although the basic physical principles described in the text are universally useful in the context of dense polycrystalline devices. However, the readers must be careful of how the microstructure heterogeneity and grain-boundary chemistry are capable to interfere in the global electrical response for particular systems. New perspectives for applications, commercialization and degradation studies involving SnO2-based polycrystalline non-ohmic systems are also outlined, including recent technological developments. Finally, at the end of this review a brief section is particularly dedicated to the presentation and discussions about others emerging non-ohmic polycrystalline ceramic devices (particularly based on perovskite ceramics) which must be deeply studied in the years to come, specially because some of these systems present combined high dielectric and non-ohmic properties. From both scientific and technological point of view these perovskite systems are quite interesting. (c) 2007 Elsevier Ltd. All rights reserved.
Resumo:
Includes bibliography
Resumo:
Includes bibliography
Resumo:
We consider the non-Markovian Langevin evolution of a dissipative dynamical system in quantum mechanics in the path integral formalism. After discussing the role of the frequency cutoff for the interaction of the system with the heat bath and the kernel and noise correlator that follow from the most common choices, we derive an analytic expansion for the exact non-Markovian dissipation kernel and the corresponding colored noise in the general case that is consistent with the fluctuation-dissipation theorem and incorporates systematically non-local corrections. We illustrate the modifications to results obtained using the traditional (Markovian) Langevin approach in the case of the exponential kernel and analyze the case of the non-Markovian Brownian motion. We present detailed results for the free and the quadratic cases, which can be compared to exact solutions to test the convergence of the method, and discuss potentials of a general nonlinear form. © 2013 Elsevier B.V. All rights reserved.
Resumo:
The objective of this study was to evaluate the association between the physicochemical properties and sensory acceptance of Brazilian red wines by applying chemometric techniques. Therefore, three winemaking processes were carried out: a traditional winemaking process and two novel winemaking processes, pre-drying and static pomace. Significant differences could be identified amongst the physicochemical properties of the wines (P<0.001). The sensory results showed greater acceptance of the wines made after pre-drying of the grapes or from the static pomace, as compared to commercial brands. Cluster analysis and Multidimensional Scaling were successfully applied and their results demonstrated the influence of the total phenolic content and color indexes on acceptance of the appearance of the wines. The odor was associated with the alcohol content, acidity, dry extract, total and reducing sugars and the body of the wines. The flavor was associated with several physicochemical properties which influenced the overall acceptance of the samples. © 2013 Elsevier Ltd.
Resumo:
Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)
Resumo:
Pós-graduação em Medicina Veterinária - FCAV
Resumo:
The Epstein-Barr virus (EBV) is associated with a large spectrum of lymphoproliferative diseases. Traditional methods of EBV detection include the immunohistochemical identification of viral proteins and DNA probes to the viral genome in tumoral tissue. The present study explored the detection of the EBV genome, using the BALF5 gene, in the bone marrow or blood mononuclear cells of patients with diffuse large B-cell lymphomas (DLBCL) and related its presence to the clinical variables and risk factors. The results show that EBV detection in 21.5% of patients is not associated with age, gender, staging, B symptoms, international prognostic index scores or any analytical parameters, including lactate dehydrogenase (LDH) or beta-2 microglobulin (B2M). The majority of patients were treated with R-CHOP-like (rituximab. cyclophosphamide, doxorubicin, vincristine and prednisolone or an equivalent combination) and some with CHOP-like chemotherapy. Response rates [complete response (CR) + partial response (PR)] were not significantly different between EBV-negative and -positive cases, with 93.2 and 88.9%, respectively. The survival rate was also similar in the two groups, with 5-year overall survival (OS) rates of 64.3 and 76.7%, respectively. However, when analyzing the treatment groups separately there was a trend in EBV-positive patients for a worse prognosis in patients treated with CHOP-like regimens that was not identified in patients treated with R-CHOP-like regimens. We conclude that EBV detection in the bone marrow and blood mononuclear cells of DLBC patients has the same frequency of EBV detection on tumoral lymphoma tissue but is not associated with the risk factors, response rate and survival in patients treated mainly with immunochemotherapy plus rituximab. These results also suggest that the addition of rituximab to chemotherapy improves the prognosis associated with EBV detection in DLBCL.
Resumo:
English: The assessment of safety in existing bridges and viaducts led the Ministry of Public Works of the Netherlands to finance a specific campaing aimed at the study of the response of the elements of these infrastructures. Therefore, this activity is focused on the investigation of the behaviour of reinforced concrete slabs under concentrated loads, adopting finite element modeling and comparison with experimental results. These elements are characterized by shear behaviour and crisi, whose modeling is, from a computational point of view, a hard challeng, due to the brittle behavior combined with three-dimensional effects. The numerical modeling of the failure is studied through Sequentially Linear Analysis (SLA), an alternative Finite Element method, with respect to traditional incremental and iterative approaches. The comparison between the two different numerical techniques represents one of the first works and comparisons in a three-dimensional environment. It's carried out adopting one of the experimental test executed on reinforced concrete slabs as well. The advantage of the SLA is to avoid the well known problems of convergence of typical non-linear analysis, by directly specifying a damage increment, in terms of reduction of stiffness and resistance in particular finite element, instead of load or displacement increasing on the whole structure . For the first time, particular attention has been paid to specific aspects of the slabs, like an accurate constraints modeling and sensitivity of the solution with respect to the mesh density. This detailed analysis with respect to the main parameters proofed a strong influence of the tensile fracture energy, mesh density and chosen model on the solution in terms of force-displacement diagram, distribution of the crack patterns and shear failure mode. The SLA showed a great potential, but it requires a further developments for what regards two aspects of modeling: load conditions (constant and proportional loads) and softening behaviour of brittle materials (like concrete) in the three-dimensional field, in order to widen its horizons in these new contexts of study.
Resumo:
This doctoral thesis was focused on the investigation of enantiomeric and non-enantiomeric biogenic organic compound (BVOC) emissions from both leaf and canopy scales in different environments. In addition, the anthropogenic compounds benzene, toluene, ethylbenzene, and xylenes (BTEX) were studied. BVOCs are emitted into the lower troposphere in large quantities (ca. 1150 Tg C ·yr-1), approximately an order of magnitude greater than the anthropogenic VOCs. BVOCs are particularly important in tropospheric chemistry because of their impact on ozone production and secondary organic aerosol formation or growth. The BVOCs examined in this study were: isoprene, (-)/ (+)-α-pinene, (-)/ (+)-ß-pinene, Δ-3-carene, (-)/ (+)-limonene, myrcene, eucalyptol and camphor, as these were the most abundant BVOCs observed both in the leaf cuvette study and the ambient measurements. In the laboratory cuvette studies, the sensitivity of enantiomeric enrichment change from the leaf emission has been examined as a function of light (0-1600 PAR) and temperature (20-45°C). Three typical Mediterranean plant species (Quercus ilex L., Rosmarinus officinalis L., Pinus halepensis Mill.) with more than three individuals of each have been investigated using a dynamic enclosure cuvette. The terpenoid compound emission rates were found to be directly linked to either light and temperature (e.g. Quercus ilex L.) or mainly to temperature (e.g. Rosmarinus officinalis L., Pinus halepensis Mill.). However, the enantiomeric signature showed no clear trend in response to either the light or temperature; moreover a large variation of enantiomeric enrichment was found during the experiment. This enantiomeric signature was also used to distinguish chemotypes beyond the normal achiral chemical composition method. The results of nineteen Quercus ilex L. individuals, screened under standard conditions (30°C and 1000 PAR) showed four different chemotypes, whereas the traditional classification showed only two. An enclosure branch cuvette set-up was applied in the natural boreal forest environment from four chemotypes of Scots pine (Pinus sylvestris) and one chemotype of Norway spruce (Picea abies) and the direct emissions compared with ambient air measurements above the canopy during the HUMPPA-COPEC 2010 summer campaign. The chirality of a-pinene was dominated by (+)-enantiomers from Scots pine while for Norway spruce the chirality was found to be opposite (i.e. Abstract II (-)-enantiomer enriched) becoming increasingly enriched in the (-)-enantiomer with light. Field measurements over a Spanish stone pine forest were performed to examine the extent of seasonal changes in enantiomeric enrichment (DOMINO 2008). These showed clear differences in chirality of monoterpene emissions. In wintertime the monoterpene (-)-a-pinene was found to be in slight enantiomeric excess over (+)-a-pinene at night but by day the measured ratio was closer to one i.e. racemic. Samples taken the following summer in the same location showed much higher monoterpene mixing ratios and revealed a strong enantiomeric excess of (-)-a-pinene. This indicated a strong seasonal variance in the enantiomeric emission ratio which was not manifested in the day/night temperature cycles in wintertime. A clear diurnal cycle of enantiomeric enrichment in a-pinene was also found over a French oak forest and the boreal forest. However, while in the boreal forest (-)-a-pinene enrichment increased around the time of maximum light and temperature, the French forest showed the opposite tendency with (+)-a-pinene being favored. For the two field campaigns (DOMINO 2008 and HUMPPA-COPEC 2010), the BTEX were also investigated. For the DOMINO campaign, mixing ratios of the xylene isomers (meta- and para-) and ethylbenzene, which are all well resolved on the ß-cyclodextrin column, were exploited to estimate average OH radical exposures to VOCs from the Huelva industrial area. These were compared to empirical estimates of OH based on JNO2 measured at the site. The deficiencies of each estimation method are discussed. For HUMPPA-COPEC campaign, benzene and toluene mixing ratios can clearly define the air mass influenced by the biomass burning pollution plume from Russia.
Resumo:
Purpose: Acupuncture is one of the complementary medicine therapies with the greatest demand in Switzerland and many other countries in the West and in Asia. Over the past decades, the pool of scientific literature in acupuncture has markedly increased. The diagnostic methods upon which acupuncture treatment is based, have only been addressed sporadically in scientific journals. The goal of this study is to assess the use of different diagnostic methods in the acupuncture practices and to investigate similarities and differences in using these diagnostic methods between physician and non-physician acupuncturists. Methods: 44 physician acupuncturists with certificates of competence in acupuncture – traditional chinese medicine (TCM) from ASA (Assoziation Schweizer Ärztegesellschaften für Akupunktur und Chinesische Medizin: the Association of Swiss Medical Societies for Acupuncture and Chinese Medicine) and 33 non-physician acupuncturists listed in the EMR (Erfahrungsmedizinisches Register: a national register, which assigns a quality label for CAM therapists in complementary and alternative medicine) in the cantons Basel-Stadt and Basel-Land were asked to fill out a questionnaire on diagnostic methods. The responder rate was 46.8% (69.7% non-physician acupuncturists and 29, 5% physician acupuncturists). Results: The results show that both physician and non-physician acupuncturists take patients’ medical history (94%), use pulse diagnosis (89%), tongue diagnosis (83%) and palpation of body and ear acupuncture points (81%) as diagnostic methods to guide their acupuncture treatments. Between the two groups, there were significant differences in the diagnostic tools being used. Physician acupuncturists do examine their patients significantly more often with western medical methods (p<.05) than this is the case for nonphysician acupuncturists. Non-physician acupuncturists use pulse diagnosis more often than physicians (p<.05). A highly significant difference was observed in the length of time spent with collecting patients’ medical history, where nonphysician acupuncturists clearly spent more time (p<.001). Conclusion: Depending on the educational background of the acupuncturist, different diagnostic methods are used for making the diagnosis. Especially the more time consuming methods like a comprehensive anamnesis and pulse diagnosis are more frequently employed by non-physician practitioners. Further studies will clarify if these results are valid for Switzerland in general, and to what extent the differing use of diagnostic methods has an impact on the diagnosis itself and on the resulting treatment methods, as well as on the treatment success and the patients’ satisfaction.
Performance Tuning Non-Uniform Sampling for Sensitivity Enhancement of Signal-Limited Biological NMR
Resumo:
Non-uniform sampling (NUS) has been established as a route to obtaining true sensitivity enhancements when recording indirect dimensions of decaying signals in the same total experimental time as traditional uniform incrementation of the indirect evolution period. Theory and experiments have shown that NUS can yield up to two-fold improvements in the intrinsic signal-to-noise ratio (SNR) of each dimension, while even conservative protocols can yield 20-40 % improvements in the intrinsic SNR of NMR data. Applications of biological NMR that can benefit from these improvements are emerging, and in this work we develop some practical aspects of applying NUS nD-NMR to studies that approach the traditional detection limit of nD-NMR spectroscopy. Conditions for obtaining high NUS sensitivity enhancements are considered here in the context of enabling H-1,N-15-HSQC experiments on natural abundance protein samples and H-1,C-13-HMBC experiments on a challenging natural product. Through systematic studies we arrive at more precise guidelines to contrast sensitivity enhancements with reduced line shape constraints, and report an alternative sampling density based on a quarter-wave sinusoidal distribution that returns the highest fidelity we have seen to date in line shapes obtained by maximum entropy processing of non-uniformly sampled data.
Resumo:
This project considered the second stage of transforming local administration and public service management to reflect democratic forms of government. In Hungary in the second half of the 1990s more and more public functions delegated to local governments have been handed over to the private or civil sectors. This has led to a relative decrease of municipal functions but not of local governments' responsibilities, requiring them to change their orientation and approach to their work so as to be effective in their new roles of managing these processes rather than traditional bureaucratic administration. Horvath analysed the Anglo-Saxon, French and German models of self-government, identifying the differing aspects emphasised in increasing the private sector's role in the provision of public services, and the influence that this process has on the system of public administration. He then highlighted linkages between actors and local governments in Hungary, concluding that the next necessary step is to develop institutional mechanisms, financial incentives and managerial practices to utilise the full potential of this process. Equally important is the need for conscious avoidance of restrictive barriers and unintended consequences, and for local governments to confront the social conflicts that have emerged in parallel with privatisation. A further aspect considered was a widening of the role of functional governance at local level in the field of human services. A number of different special purpose bodies have been set up in Hungary, but the results of their work are unclear and Horvath feels that this institutionalisation of symbiosis is not the right path in Hungary today. He believes that the change from local government to local governance will require the formulation of specific public policy, the relevance of which can be proven by processes supported with actions.