Emergy analysis of oil production from microalgae

The use of microalgae and cyanobacteria for the production of biofuels and other raw materials is considered a very promising sustainable technology due to the high areal productivity, potential for CO2 fixation and use of non-arable land. The production of oil by microalgae in a large scale plant was studied using emergy analysis. The joint transformity calculated for the base scenario was 1.32E + 5 sej/J, the oil transformity was 3.51E + 5 sej/J, the emergy yield ratio (EYR) was 1.09 and environmental loading ratio was 11.10 and the emergy sustainability index (ESI) was 0.10, highlighting some of the key challenges for the technology such as high energy consumption during harvesting, raw material consumption and high capital and operation costs. Alternatives scenarios and the sensitivity to process improvements were also assessed, helping prioritize further research based on sustainability impact. (C) 2012 Elsevier Ltd. All rights reserved.

USE OF BARU OIL (Dipteryx alata Vog.) TO PRODUCE BIODIESEL AND STUDY OF THE PHYSICAL AND CHEMICAL CHARACTERISTICS OF BIODIESEL/PETROLEUM DIESEL FUEL BLENDS

We describe production of methyl and ethyl esters derived from baru oil (Dipteryx alata Vog.). Water and alcohols are removed from the biodiesel obtained by simple distillation. We study the acidity, density, iodine number, viscosity, water content, peroxide number, external appearance, and saponification number of the oil, its methyl and ethyl esters (biodiesels) and their blends (B5, B10, B15, B20, and B30) with commercial diesel fuel.

Genotoxicity assessment of water soluble fractions of biodiesel and its diesel blends using the Salmonella assay and the in vitro MicroFlow (R) kit (Litron) assay

The designation of biodiesel as an environmental-friendly alternative to diesel oil has improved its commercialization and use. However, most biodiesel environmental safety studies refer to air pollution and so far there have been very few literature data about its impacts upon other biotic systems, e.g. water, and exposed organisms. Spill simulations in water were carried out with neat diesel and biodiesel and their blends aiming at assessing their genotoxic potentials should there be contaminations of water systems. The water soluble fractions (WSF) from the spill simulations were submitted to solid phase extraction with C-18 cartridge and the extracts obtained were evaluated carrying out genotoxic and mutagenic bioassays [the Salmonella assay and the in vitro MicroFlow (R) kit (Litron) assay]. Mutagenic and genotoxic effects were observed, respectively, in the Salmonella/microsome preincubation assay and the in vitro MN test carried out with the biodiesel WSF. This interesting result may be related to the presence of pollutants in biodiesel derived from the raw material source used in its production chain. The data showed that care while using biodiesel should be taken to avoid harmful effects on living organisms in cases of water pollution. (C) 2011 Elsevier Ltd. All rights reserved.

Material embodiment and energy flows as efficiency indicators of soybean (Glycine max) production in Brazil

As the requirement for agriculture to be environmentally suitable there is a necessity to adopt indicators and methodologies approaching sustainability. In Brazil, biodiesel addition into diesel is mandatory and soybean oil is its main source. The material embodiment determines the convergence of inputs into the crop. Moreover, the material flows are necessary for any environmental analysis. This study evaluated distinct production scenarios, and also conventional versus GMO crops, through the material embodiment and energy analysis. GMO crops demanded less indirectly applied inputs. The energy balance showed linearity with yield, whereas for EROI, the increases in input and yield were not affected.

Using biomass-based fuels including pyrolysis liquids for power and CHP production

The use of biomass-derived liquids (in short: bioliquids) instead of solid biomass can help overcome some of the barriers hindering a wider use of biomass in smaller-scale CHP systems. Relevant bioliquids included biodiesel, vegetable oils as well straight and upgraded pyrolysis oil. In this joint EU-Russian research project Bioliquids-CHP prime movers (engines and turbines) will be developed and modified so that these can run efficiently on bioliquids. At the same time, bioliquids will be upgraded and blended in order to facilitate their use in prime movers. Preliminary results with regard to bioliquid selection, production, and characterisation; the selection and modification of a micro gas turbine; and the development of engines and components are discussed. The research also covers NOx emission reduction and control and an assessment of the benefits and economics of bioliquids-based CHP systems in EU and Russian markets.

Nanoporous solid acid and base catalysts for sustainable biofuels production

Dwindling fossil fuel reserves, and growing concerns over CO2 emissions and associated climate change, are driving the quest for renewable feedstocks to provide alternative, sustainable fuel sources. Catalysis has a rich history of facilitating energy efficient, selective molecular transformations, and in a post-petroleum era will play a pivotal role in overcoming the scientific and engineering barriers to economically viable, and sustainable, biofuels derived from renewable resources. The production of second generation biofuels, derived from biomass sourced from inedible crop components, e.g. agricultural or forestry waste, or alternative non-food crops such as Switchgrass or Jatropha Curcas that require minimal cultivation, necessitate new heterogeneous catalysts and processes to transform these polar and viscous feedstocks [1]. Here we show how advances in the rational design of nanoporous solid acids and bases, and their utilisation in novel continuous reactors, can deliver superior performance in the energy-efficient esterification and transesterification of bio-oil components into biodiesel [2-4]. Notes: [1] K. Wilson, A.F. Lee, Cat. Sci. Tech. 2012 ,2, 884. [2] J. Dhainaut, J.-P. Dacquin, A. F. Lee, K. Wilson, Green Chem. 2010 , 12, 296. [3] C. Pirez, J.-M. Caderon, J.-P. Dacquin, A.F. Lee, K. Wilson, ACS Catal. 2012 , 2, 1607. [4] J.J. Woodford, J.-P. Dacquin, K. Wilson, A.F. Lee, Energy Environ. Sci. 2012 , 5, 6145.

Kinetic modeling studies of heterogeneously catalyzed biodiesel synthesis reactions

The heterogeneously catalyzed transesterification reaction for the production of biodiesel from triglycerides was investigated for reaction mechanism and kinetic constants. Three elementary reaction mechanisms Eley-Rideal (ER), Langmuir-Hinshelwood-Hougen-Watson (LHHW), and Hattori with assumptions, such as quasi-steady-state conditions for the surface species and methanol adsorption, and surface reactions as the rate-determining steps were applied to predict the catalyst surface coverage and the bulk concentration using a multiscale simulation framework. The rate expression based on methanol adsorption as the rate limiting in LHHW elementary mechanism has been found to be statistically the most reliable representation of the experimental data using hydrotalcite catalyst with different formulations. © 2011 American Chemical Society.

Energy production from biomass and waste derived intermediate pyrolysis oils

This study investigates the use of Pyroformer intermediate pyrolysis system to produce alternative diesel engines fuels (pyrolysis oil) from various biomass and waste feedstocks and the application of these pyrolysis oils in a diesel engine generating system for Combined Heat and Power (CHP) production. The pyrolysis oils were produced in a pilot-scale (20 kg/h) intermediate pyrolysis system. Comprehensive characterisations, with a view to use as engine fuels, were carried out on the sewage sludge and de-inking sludge derived pyrolysis oils. They were both found to be able to provide sufficient heat for fuelling a diesel engine. The pyrolysis oils also presented poor combustibility and high carbon deposition, but these problems could be mitigated by means of blending the pyrolysis oils with biodiesel (derived from waste cooking oil). The blends of SSPO (sewage sludge pyrolysis oil) and biodiesel (30/70 and 50/50 in volumetric ratios) were tested in a 15 kWe Lister type stationary generating system for up to 10 hours. There was no apparent deterioration observed in engine operation. With 30% SSPO blended into biodiesel, the engine presents better overall performance (electric efficiency), fuel consumption, and overall exhaust emissions than with 50% SSPO blend. An overall system analysis was carried out on a proposed integrated Pyroformer-CHP system. Combined with real experimental results, this was used for evaluating the costs for producing heat and power and char from wood pellets and sewage sludge. It is concluded that the overall system efficiencies for both types of plant can be over 40%; however the integrated CHP system is not economically viable. This is due to extraordinary project capital investment required.

Otimização da síntese do AlSBA-15 para produção de biodiesel por transesteri-ficação do óleo de coco

Stimulus encouraging the production and consumption of biodiesel favors the policy of pre-serving the environment, contributing to the reduction of greenhouse gas reducing climate change. The current trend of research in this field focuses on improving these processes with the use of heterogeneous catalysts, seeing has significant advantages such as: low contamination of products, ease of separation of the catalyst from the reaction medium, possibili-ty of reuse of the catalyst, decreased corrosion problems. The objective of this research was to optimize the synthesis of AlSBA-15 for the production of biodiesel through transesterification process via ethyl route. For the optimization of hydrothermal synthesis of type AlSBA-15 catalyst has assembled a 23 factorial experimental matrix with eleven trials. The stoichiometric amounts of starting materials were varied according to different ratios Si / Al which is a factor in the experimental design, in addition to the time and temperature of aging of the synthesis gel. The material showed the best results of characterization (SBET = 591.7 (m2 / g), Vp = 0.83 (cm3 / g), Dp = 5.59 (nm), w = 6.48 (nm) was synthesized at 100 ° C for 24 hours, with a ratio Si / Al = 10.This material was applied as a heterogeneous catalyst in the reaction of ethyl transesterification as raw coconut oil in natura. Coconut oil presented suitable for obtaining biodiesel via ethyl route.The visual aspects and physical-chemical characteristics of the reaction products show that AlSBA-15 catalyst favored the reaction. According to physical-chemical analysis the order of oxidative stability of the product of the transesterification reaction was: catalytic reaction at 1500 ° C> non-catalytic reaction at 100 ° C> 100 ° C catalytic> catalytic reaction at 200 ° C Reaction. The results of oxidative stability and kinematic viscosity shows that the biodiesel produced in the catalytic sandblasting held at 150 ° C which was maintained within the ABNT NBR 7148, ABNT NBR 10441 and EN 14112.

Optimization of lipase production from yeasts strains isolated from olive mil wastewater

Dissertação submetida à Universidade de Lisboa, Faculdade de Ciências para a obtenção do Grau de Mestre em Microbiologia Aplicada.

Produção biológica integrada de hidrogénio e metano a partir de resíduos da indústria do biodiesel

Dissertação de Mestrado Integrado em Engenharia da Energia e do Ambiente

Biodiesel a partir de óleos de alta acidez: desenvolvimento de um processo catalítico homogêneo

O presente trabalho visa o desenvolvimento de um processo para a produção de biodiesel partindo de óleos de alta acidez, aplicando um processo em duas etapas de catálise homogênea. A primeira é a reação de esterificação etílica dos ácidos graxos livres, catalisada por H2SO4, ocorrendo no meio de triglicerídeos e a segunda é a transesterificação dos triglicerídeos remanescentes, ocorrendo no meio dos ésteres alquílicos da primeira etapa e catalisada com álcali (NaOH) e álcool etílico ou metílico. A reação de esterificação foi estudada com uma mistura modelo consistindo de óleo de soja neutro acidificado artificialmente com 15%p de ácido oleico PA. Este valor foi adotado, como referência, devido a certas gorduras regionais (óleo de mamona advinda de agricultura familiar, sebos de matadouro e óleo de farelo de arroz, etc.) apresentarem teores entre 10-20%p de ácidos graxos livres. Nas duas etapas o etanol é reagente e também solvente, sendo a razão molar mistura:álcool um dos parâmetros pesquisados nas relações 1:3, 1:6 e 1:9. Outros foram a temperatura 60 e 80ºC e a concentração percentual do catalisador, 0,5, 1,0 e 1,5%p, (em relação à massa de óleo). A combinatória destes parâmetros resultou em 18 reações. Dentre as condições reacionais estudadas, oito atingiram acidez aceitável inferior a 1,5%p possibilitando a definição das condições para aplicação ótima da segunda etapa. A melhor condição nesta etapa ocorreu quando a reação foi conduzida a 60°C com 1%p de H2SO4 e razão molar 1:6. No final da primeira etapa foram realizados tratamentos pertinentes como a retirada do catalisador e estudada sua influência sobre a acidez final, utilizando-se de lavagens com e sem adição de hexano, seguidas de evaporação ou adição de agente secante. Na segunda etapa estudaram-se as razões molares de óleo:álcool de 1:6 e 1:9 com álcool metílico e etílico, com 0,5 e 1%p de NaOH assim como o tratamento da reação (lavagem ou neutralização do catalisador) a 60°C, resultando em 16 experimentos. A melhor condição nesta segunda etapa ocorreu com 0,5%p de NaOH, razão molar óleo:etanol de 1:6 e somente as reações em que se aplicaram lavagens apresentaram índices de acidez adequados (<1,0%p) coerentes com os parâmetros da ANP.

Síntese de biodiesel etílico de girassol utilizando transesterificação alcalina seguido da adição on pot de H2SO4

No presente trabalho foi investigada a adição on pot de H2SO4 no processo de transesterificação do óleo de girassol com etanol e metanol empregando catalisador alcalino (NaOH e KOH). Após o processo, ocorreu uma eficiente separação tanto do biodiesel etílico como metílico de seus co-produtos. Com a adição on pot de H2SO4 todo sabão formado no meio reacional foi transformado em ácidos graxos livres e o catalisador em sal (Na2SO4 ou K2SO4). A esterificação dos ácidos graxos livres presentes no biodiesel foi aplicada para atingir os padrões de biocombustíveis. Os ácidos graxos contidos no biodiesel foram esterificados na presença de uma mistura com razão molar de 60:1 e 80:1 álcool:ácido graxo, com H2SO4 5 e 10 % em massa. Também foi avaliada a influência da quantidade de catalisador na reação paralela de saponificação. De acordo com os resultados observou-se que a quantidade de sabão formado no processo, variou entre 1,80 e 10,66 % para 1 e 2 % de catalisador, respectivamente. A adição on pot de H2SO4 permitiu aumentar o rendimento de obtenção de biodiesel, e reduziu a geração de efluentes provenientes das lavagens para remoção do sabão, quando comparado com o processo convencional. As análises foram realizadas para avaliar a qualidade do biodiesel, com exceção da estabilidade oxidativa, os demais parâmetros estão de acordo com as normas da ANP. A glicerina foi obtida com uma pureza de 95 % de glicerol com aspecto límpido e incolor, sendo seu principal contaminante o sal proveniente da neutralização do catalisador.

Desenvolvimento e validação de método para determinação do perfil graxo do biodiesel de Tungue e Blendas com soja empregando GC-MS

No Brasil o biodiesel é utilizado em misturas com óleo diesel em proporções de 5%, sem que haja modificações nos motores. Com o intuito de diversificar a utilização de oleaginosas não comestíveis no ramo dos biocombustíveis, e ainda vincular a produção com agricultura sustentável, uma alternativa para o RS é a utilização do óleo de tungue para a produção de biodiesel. A caracterização e quantificação de ácidos graxos do biodiesel de tungue, torna-se importante devido à seu exclusivo perfil graxo. Neste trabalho, foi estudado o desenvolvimento e validação de método para a determinação do perfil graxo do biodiesel metílico de tungue e blendas com soja utilizando GC-MS. Os parâmetros de validação considerados foram: curva analítica, linearidade, seletividade, limite de detecção e quantificação, robustez, precisão e exatidão. Para determinar as melhores condições cromatográficas, foram testadas diferentes programações de temperatura no forno cromatográfico; fluxo de gás; temperatura do injetor, detector e interface; e modo de injeção. As condições do GCMS após a otimização foram: injeção de 1 µL com injeção em alta pressão (300 kPa), T do injetor: 250 ºC, injeção split 1:30, fluxo de 1 mL min-1, coluna Rtx-5MS com dimensões 30 m x 0,25 mm x 0,25 µm, T forno: isoterma de 2 min a 130 ºC, aumento de 20 ºC/min até 220 ºC, aumento de 0,5ºC/min até 223ºC, aumento de 7 ºC/min até 250 ºC e isoterma em 250 ºC por 3 min, resultando em 20 min de análise. A temperatura da fonte e interface foram de 200 ºC e 250 ºC, respectivamente, com o MS no modo full scan, ionização por impacto eletrônico a 70 eV, e intervalo de massas de 30 a 500 u.m.a. A identificação do α-eleosteárico foi baseada na fragmentação característica do composto, pela comparação com o espectro do ácido linolênico, e ainda pelo tempo de retenção do composto. Na validação, as curvas analíticas apresentaram valores de r maiores que 0,99. O LD e LQ foram adequados, permitindo a quantificação de ésteres na concentração mínima de 0,6%. Os valores de exatidão ficaram entre 86 e 117%, com RSD% menores que 8%. O efeito matriz também foi avaliado, sendo que esse efeito foi considerado médio para a maioria dos compostos, ficando entre ± 20 e 50%. Durante a aplicação do método, o mesmo se mostrou adequado para amostras de biodiesel metílico de tungue e blendas com soja, nas proporções de 15:85, 20:80 e 25:75 (T:S, v/v). A aplicabilidade do método também foi testada para o biodiesel de soja, obtendo resultados satisfatórios, mostrando-se assim, além de tudo, ser um método robusto.

Physiology and biochemistry of the effect of abiotic stress on the autochthonous CTP4 strain, a candidate microalga for biofuel production in Algarve

Dissertação de Mestrado, Biologia Marinha, Faculdade de Ciências e Tecnologia, Universidade do Algarve, 2014