New measurements on the absolute cosmic ray ionization from sea level to 1540 kilometers altitude

An air filled ionization chamber has been constructed with a volume of 552 liters and a wall consisting of 12.7 mg/cm² of plastic wrapped over a rigid, lightweight aluminum frame. A calibration in absolute units, independent of previous Caltech ion chamber calibrations, was applied to a sealed Neher electrometer for use in this chamber. The new chamber was flown along with an older, argon filled, balloon type chamber in a C-135 aircraft from 1,000 to 40,000 feet altitude, and other measurements of sea level cosmic ray ionization were made, resulting in the value of 2.60 ± .03 ion pairs/cm³ sec atm) at sea level. The calibrations of the two instruments were found to agree within 1 percent, and the airplane data were consistent with previous balloon measurements in the upper atmosphere. Ionization due to radon gas in the atmosphere was investigated. Absolute ionization data in the lower atmosphere have been compared with results of other observers, and discrepancies have been discussed.

Data from a polar orbiting ion chamber on the OGO-II, IV spacecraft have been analyzed. The problem of radioactivity produced on the spacecraft during passes through high fluxes of trapped protons has been investigated, and some corrections determined. Quiet time ionization averages over the polar regions have been plotted as function of altitude, and an analytical fit is made to the data that gives a value of 10.4 ± 2.3 percent for the fractional part of the ionization at the top of the atmosphere due to splash albedo particles, although this result is shown to depend on an assumed angular distribution for the albedo particles. Comparisons with other albedo measurements are made. The data are shown to be consistent with balloon and interplanetary ionization measurements. The position of the cosmic ray knee is found to exhibit an altitude dependence, a North-South effect, and a small local time variation.

The statistical bootstrap model

A review is presented of the statistical bootstrap model of Hagedorn and Frautschi. This model is an attempt to apply the methods of statistical mechanics in high-energy physics, while treating all hadron states (stable or unstable) on an equal footing. A statistical calculation of the resonance spectrum on this basis leads to an exponentially rising level density ρ(m) ~ cm^-3 e^βom at high masses.

In the present work, explicit formulae are given for the asymptotic dependence of the level density on quantum numbers, in various cases. Hamer and Frautschi's model for a realistic hadron spectrum is described.

A statistical model for hadron reactions is then put forward, analogous to the Bohr compound nucleus model in nuclear physics, which makes use of this level density. Some general features of resonance decay are predicted. The model is applied to the process of NN annihilation at rest with overall success, and explains the high final state pion multiplicity, together with the low individual branching ratios into two-body final states, which are characteristic of the process. For more general reactions, the model needs modification to take account of correlation effects. Nevertheless it is capable of explaining the phenomenon of limited transverse momenta, and the exponential decrease in the production frequency of heavy particles with their mass, as shown by Hagedorn. Frautschi's results on "Ericson fluctuations" in hadron physics are outlined briefly. The value of β_o required in all these applications is consistently around [120 MeV]^-1 corresponding to a "resonance volume" whose radius is very close to ƛ_π. The construction of a "multiperipheral cluster model" for high-energy collisions is advocated.

激光功率密度对Al膜靶后表面快电子发射的影响

报道了在20 TW皮秒激光器上完成的p偏振激光与等离子体相互作用过程中产生的快电子的角分布和能谱测量结果.实验得到：当激光功率密度小于1017 W/cm^2时,电子发射没有明显定向性,在激光入射面内多峰发射;当激光功率密度大于1017 W/cm^2,小于1018 W/cm^2时,电子主要沿靶面法线方向发射;当激光功率密度达到相对论强度时,电子主要沿激光传播方向发射;激光功率密度未达到相对论强度时,靶后表面法线方向快电子能谱拟合平均温度符合共振吸收温度定标率;激光功率密度达相对论强度以上时,靶后表面法线方向

Ba（NO3）2晶体受激拉曼散射的角度分布和脉冲压缩(英文)

报道了利用重复频率为30HZ，波长为532nm的Nd：YAG倍频激光单次通过抽运硝酸钡（Ba（NO3）2）晶体（晶体由水溶液降温法生长，长度为48mm，横截面为10mm×10mm），获得高效率的一阶（563nm），二阶（599nm）和三阶（639nm）斯托克斯光的实验结果．硝酸钡晶体沿着[110]晶轴方向切割．观测到一、二、三阶斯托克斯光呈锥形环分布，一、二、三阶斯托克斯光的散射外边缘与抽运光轴线间的夹角大小分别为1．7°，3．5°，5．0°．同时也观测到Ba（NO3）2的SRS角度分布与抽运光强度无关．

Análise da produção de dijatos de difração simples no experimento CMS/LHC

O escopo desse trabalho é a observação de dijatos de difração simples em colisões pp com ps = 7 TeV, durante os primeiros períodos de aquisição de dados do experimento CMS/LHC. A técnica utilizada foi a medida da multiplicidade no calorímetro HF. Os dados foram analisados para diferentes períodos de aquisição de dados do ano de 2010, com ∫ Ldt ~_ 3,2 pb-1. Comparamos os dados observados com o Monte Carlo simulado com efeito de empilhamento e sem esse efeito.

Estudo do comportamento de variáveis cinemáticas na produção difrativa de mésons D-+* em colisões próton-próton √s = 7TeV

Apresentamos um estudo preliminar da produção difrativa de mésons utilizando dados obtidos da colisão próton-próton, a energias de centro de massa de 7 TeV, com o experimento CMS-LHC. O trabalho inclui o desenvolvimento do algoritmo de reconstrução dos mésons D* através do canal de decaimento D*->D0 + pion (lento) ->K+pion, a medida da eficiência de detecção e reconstrução, e uma análise do comportamento de variáveis cinemáticas na produção difrativa dessas partículas, particularmente, das lacunas de rapidez. Para isso, foi utilizada uma luminosidade integrada de 3,171pb^(-1) de dados coletados no ano de 2010. As análises com os dados experimentais foram comparadas com os resultados obtidos com geradores de Monte Carlo PYTHIA6, PYTHIA8 e POMPYT.

Spectroscopy of neutron-rich Dy168,170: Yrast band evolution close to the NpNn valence maximum

The yrast sequence of the neutron-rich dysprosium isotope Dy168 has been studied using multinucleon transfer reactions following collisions between a 460-MeV Se82 beam and an Er170 target. The reaction products were identified using the PRISMA magnetic spectrometer and the γ rays detected using the CLARA HPGe-detector array. The 2+ and 4+ members of the previously measured ground-state rotational band of Dy168 have been confirmed and the yrast band extended up to 10+. A tentative candidate for the 4+→2+ transition in Dy170 was also identified. The data on these nuclei and on the lighter even-even dysprosium isotopes are interpreted in terms of total Routhian surface calculations and the evolution of collectivity in the vicinity of the proton-neutron valence product maximum is discussed. © 2010 The American Physical Society.

Intrinsic state lifetimes in Pd103 and Cd106,107

The mean-lifetimes, τ, of various medium-spin excited states in Pd103 and Cd106,107 have been deduced using the Recoil Distance Doppler Shift technique and the Differential Decay Curve Method. In Cd106, the mean-lifetimes of the Iπ=12+ state at Ex=5418 keV and the Iπ=11- state at Ex=4324 keV have been deduced as 11.4(17)ps and 8.2(7)ps, respectively. The associated β2 deformation within the axially-symmetric deformed rotor model for these states are 0.14(1) and 0.14(1), respectively. The β2 deformation of 0.14(1) for the Iπ=12+ state in Cd106 compares with a predicted β2 value from total Routhian surface (TRS) calculations of 0.17. In addition, the mean-lifetimes of the yrast Iπ=152- states in Pd103 (at Ex=1262 keV) and Cd107 (at Ex=1360 keV) have been deduced to be 31.2(44)ps and 31.4(17)ps, respectively, corresponding to β2 values of 0.16(1) and 0.12(1) assuming axial symmetry. Agreement with TRS calculations are good for Pd103 but deviate for that predicted for Cd107. © 2007 The American Physical Society.

Structural and thermodynamic properties of different phases of supercooled liquid water.

Computer simulation results are reported for a realistic polarizable potential model of water in the supercooled region. Three states, corresponding to the low density amorphous ice, high density amorphous ice, and very high density amorphous ice phases are chosen for the analyses. These states are located close to the liquid-liquid coexistence lines already shown to exist for the considered model. Thermodynamic and structural quantities are calculated, in order to characterize the properties of the three phases. The results point out the increasing relevance of the interstitial neighbors, which clearly appear in going from the low to the very high density amorphous phases. The interstitial neighbors are found to be, at the same time, also distant neighbors along the hydrogen bonded network of the molecules. The role of these interstitial neighbors has been discussed in connection with the interpretation of recent neutron scattering measurements. The structural properties of the systems are characterized by looking at the angular distribution of neighboring molecules, volume and face area distribution of the Voronoi polyhedra, and order parameters. The cumulative analysis of all the corresponding results confirms the assumption that a close similarity between the structural arrangement of molecules in the three explored amorphous phases and that of the ice polymorphs I(h), III, and VI exists.

Study on the stacking faults in hexagonal GaN grown by epitaxy lateral overgrowth with synchrotron radiation

By means of low temperature photoluminescence and synchrotron radiation X-ray diffraction, existence of stacking faults has been determined in epitaxy lateral overgrowth GaN by metalorganic chemical vapor deposition.

Pressure-induced phase transition of nanocrystalline zinc sulfide

In situ energy dispersive X-ray diffraction measurements on nanocrystalline zinc sulfide have been performed by using diamond anvil cell with synchrotron radiation. There is a phase transition which the ultimate structure is rocksalt when the pressure is up to 16.0GPa. Comparing the structure of body materials, the pressure of the phase transition of nano zinc sulfide is high. We fit the: Birch-Murnaghan equation of state and obtained its ambient pressure bulk modulus and its pressure derivative. The bulk modulus of nanocrystalline zinc sulfide is higher than that of body materials, it indicate that the rigidity of nanocrystalline zinc sulfide is high.

Bubble Dynamics and Heat Transfer in Microgravity Pool Boiling

Boiling is an extremely complicated and illusive process. Microgravity experiments offer a unique opportunity to study the complex interactions without external forces, such as buoyancy, which can affect the bubble dynamics and the related heat transfer. Furthermore, they can also provide a means to study the actual influence of gravity on the boiling. Two research projects on pool boiling in microgravity have been conducted aboard the Chinese recoverable satellites. Ground-based experiments both in normal gravity and in short-term microgravity in the Drop Tower Beijing and numerical simulations have also been performed. Steady boiling of R113 on thin platinum wires was studied with a temperature-controlled heating method, while quasi-steady boiling of FC-72 on a plane plate was investigated with an exponentially increasing heating voltage. It was found that the bubble dynamics in microgravity has a distinct difference from that in normal gravity, and that the heat transfer characteristic is depended upon the bubble dynamics. Lateral motions of bubbles on the heaters were observed before their departure in microgravity. The surface oscillation of the merged bubbles due to lateral coalescence between adjacent bubbles drove it to detach from the heaters. Slight enhancement of heat transfer on wires is observed in microgravity, while diminution is evident for high heat flux in the plate case.

Production of heavy and superheavy nuclei in massive fusion reactions

Within the framework of a dinuclear system (DNS) model, the evaporation-residue excitation functions and the quasi-fission mass yields in the 48Ca induced fusion reactions are investigated systematically and compared with available experimental data. Maximal production cross sections of superheavy nuclei based on stable actinide targets are obtained. Isotopic trends in the production of the superheavy elements Z = 110, 112–118 based on the actinide isotopic targets are analyzed systematically. Optimal evaporation channels and combinations as well as the corresponding excitation energies are proposed. The possible factors that influencing the isotopic dependence of the production cross sections are analyzed. The formation of the superheavy nuclei based on the isotopes U with different projectiles are also investigated and calculated.

核物质对称能的高密行为研究

One of the major tasks of studying isospin physics via heavy-ion collisions with neutron-rich nuclei, is to explore the isospin dependence of in-medium nuclear effective interactions and the equation of state of neutron-rich nuclear matter, i.e., the density dependence of nuclear symmetry energy. Because of its great importance for understanding many phenomena in both nuclear physics and astrophysics, the study of the density dependence of nuclear symmetry energy has been the main focus of the intermediate。中文摘要：同位旋物理的主要任务之一是通过放射性核束引起的核反应来探索介质中有效核子  核子相互作用的同位旋依赖性，尤其是同位旋相关的核物质状态方程，即，密度依赖的核物质对称能。由于对称能，尤其是其高密行为，对核物理学和天体物理学具有重要意义，密度依赖的对称能在过去10年一直是中能重离子物理研究领域的主要焦点之一。近年来，低密对称能的研究已经取得了重要进展，而对称能的高密行为仍然很不确定。在理论方面，人们提出了许多对高密对称能敏感的观测量。实验方面，关于对称能高密行为研究的实验计划已经展开，世界各地正在建造的放射性核束装置为对称能的高密行为研究提供了新的机遇。基于Ｉ ＢＵＵ输运模型综述了研究对称能高密行为的一些敏感观测量及其最新进展，以及所面临的挑战与机遇。

基于电路复用结构的NIM\ECL\TTL电平适配器

In this paper,a multi-functional adapter circuit which can be used to accomplish level adaptation between the NIM,TTL,ECL levels will be described briefly.This circuit is designed based on the multiple-using structure of circuit unit.It is signal-width NIM standard module.The module is used for level adaptation between the different digital signals in the measurement system of nuclear physics experiments.中文文摘：基于单元电路复用结构,设计了NIM、ECL、TTL电平多功能适配器,介绍了电路复用结构和单元电路的设计原理。该插件用于核物理实验测量系统中不同逻辑电平的数字信号的适配与转换。