Bioimpedance spectrometry in the determination of body water compartments: Accuracy and clinical significance

Bioelectrical impedance analysis (BIA) offers the potential for a simple, portable and relatively inexpensive technique for the in vivo measurement of total body water (TBW). The potential of BIA as a technique of body composition analysis is even greater when one considers that body water can be used as a surrogate measure of lean body mass. However, BIA has not found universal acceptance even with the introduction of multi-frequency BIA (MFBIA) which, potentially, may improve the predictive accuracy of the measurement. There are a number of reasons for this lack of acceptance, although perhaps the major reason is that no single algorithm has been developed which can be applied to all subject groups. This may be due, in part, to the commonly used wrist-to-ankle protocol which is not indicated by the basic theory of bioimpedance, where the body is considered as five interconnecting cylinders. Several workers have suggested the use of segmental BIA measurements to provide a protocol more in keeping with basic theory. However, there are other difficulties associated with the application of BIA, such as effects of hydration and ion status, posture and fluid distribution. A further putative advantage of MFBIA is the independent assessment not only of TBW but also of the extracellular fluid volume (ECW), hence heralding the possibility of,being able to assess the fluid distribution between these compartments. Results of studies in this area have been, to date, mixed. Whereas strong relationships of impedance values at low frequencies with ECW, and at high frequencies with TBW, have been reported, changes in impedance are not always well correlated with changes in the size of the fluid compartments (assessed by alternative and more direct means) in pathological conditions. Furthermore, the theoretical advantages of Cole-Cole modelling over selected frequency prediction have not always been apparent. This review will consider the principles, methodology and applications of BIA. The principles and methodology will,be considered in relation to the basic theory of BIA and difficulties experienced in its application. The relative merits of single and multiple frequency BIA will be addressed, with particular attention to the latter's role in the assessment of compartmental fluid volumes. (C) 1998 Elsevier Science Ltd. All rights reserved.

A comparison of segmental and wrist-to-ankle methodologies of bioimpedance analysis

The common approach of bioelectrical impedance analysis to estimate body water uses a wrist-to-ankle methodology which, although not indicated by theory, has the advantage of ease of application particularly for clinical studies involving patients with debilitating diseases. A number of authors have suggested the use of a segmental protocol in which the impedances of the trunk and limbs are measured separately to provide a methodology more in keeping with basic theory. The segmental protocol hits not, however, been generally adopted, partly because of the increased complexity involved in its application, and partly because studies comparing the two methodologies have not clearly demonstrated a significant improvement from the segmental methodology. We have conducted a small pilot study involving ten subjects to investigate the efficacy of the two methodologies in a group of normal subjects. The study did not require the independent measure of body water, by for example isotope dilution, as the subjects were maintained in a state of constant hydration with only the distribution between limbs and trunk changing as a result of change in posture. The results demonstrate a significant difference between the two methodologies in predicting the expected constancy of body water in this study, with the segmental methodology indicating a mean percentage change in extracellular water of -2.2%; which was not significantly different from the expected null result, whereas the wrist-to-ankle methodology indicated a mean percentage change in extracellular water of -6.6%. This is significantly different from the null result, and from the value obtained from the segmental methodology (p = 0.006). Similar results were obtained using estimates of total body water from the two methodologies. (C) 1998 Elsevier Science Ltd. All rights reserved.

Anomalous fluorescence spectra in an extremely weak, broadband squeezed vacuum under monochromatic and bichromatic excitation

We show that a two-level atom interacting with an extremely weak squeezed vacuum can display resonance fluorescence spectra that are qualitatively different to those that can be obtained using fields with a classical analogue. We consider first the free space situation with monochromatic excitation, and then discuss a bichromatically driven two-level atom in a cavity as a practical scenario for experimentally detecting the anomalous features predicted. We show that in the bad cavity limit, the anomalous spectral features appear for a weak squeezed vacuum and large frequency differences of the bichromatic field, conditions which are easily accessible in laboratories. The advantage of bichromatic, as opposed to monochromatic, excitation is that there is no coherent scattering at line centre which could obscure the observations. A scaling law is derived, N similar to Omega(4) which relates the squeezed photon number to the Rabi frequency at which the anomalous features appear. (C) 1998 Elsevier Science B.V.

The Australian mortality decline: all-cause mortality 1788-1990

This review describes the Australian decline in all-cause mortality, 1788-1990, and compares this with declines in Europe and North America. The period until the 1870s shows characteristic 'crisis mortality', attributable to epidemics of infectious disease. A decline in overall mortality is evident from 1880. A precipitous fall occurs in infant mortality from 1900, similar to that in European countries. Infant mortality continues downward during this century (except during the 1930s), with periods of accelerated decline during the 1940s (antibiotics) and early 1970s. Maternal mortality remains high until a precipitous fall in 1937 coinciding with the arrival of sulphonamide. Excess mortality due to the 1919 influenza epidemic is evident. Artefactual falls in mortality occur in 1930, and for men during the war of 1939-1945. Stagnation in overall mortality decline during the 1930s and 1945-1970 is evident for adult males, and during 1960-1970 for adult females. A decline in mortality is registered in both sexes from 1970, particularly in middle and older age groups, with narrowing of the sex differential. The mortality decline in Australia is broadly similar to those of the United Kingdom and several European countries, although an Australian advantage during last century and the first part of this century may have been due to less industrialisation, lower population density and better nutrition. Australia shows no war-related interruptions in the mortality decline. Australian mortality patterns from 1970 are also similar to those observed in North America and European countries (including the United Kingdom, but excluding Eastern Europe).

Cellular origin of chlorinated diketopiperazines in the dictyoceratid sponge Dysidea herbacea (Keller)

The tropical marine sponge Dysidea herbacea (Keller) contains the filamentous unicellular cyanobacterium Oscillatoria spongeliae (Schulze) Hauck as an endosymbiont, plus numerous bacteria, both intracellular and extracellular. Archaeocytes and choanocytes are the major sponge cell types present. Density gradient centrifugation of glutaraldehyde-fixed cells with Percoll as the support medium has been used to separate the cyanobacterial symbiont from the sponge cells on the basis of their differing densities. The protocol also has the advantage of separating broken from intact cells of O. spongeliae. The lighter cell preparations contain archaeocytes and choanocytes together with damaged cyanobacterial cells, whereas heavier cell preparations contain intact cyanobacterial cells, with less than 1% contamination by sponge cells. Gas chromatography/mass spectrometry analysis has revealed that the terpene spirodysin is concentrated in preparations containing archaeocytes and choanocytes, whereas nuclear magnetic resonance analysis of the symbiont cell preparations has shown that they usually contain the chlorinated diketopiperazines, dihydrodysamide C and didechlorodihydrodysamide C, which are the characteristic metabolites of the sponge/symbiont association. However, one symbiont preparation, partitioned by a second Percoll gradient, has been found to be devoid of chlorinated diketopiperazines. The capability to synthesize secondary metabolites may depend on the physiological state of the symbiont; alternatively, there may be two closely related cyanobacterial strains within the sponge tissue.

Factors influencing biodiversity and distributional gradients in mangroves

Numerous factors affect the distribution of mangrove plants. Most mangrove species are typically dispersed by water-buoyant propagules, allowing them to lake advantage of estuarine, coastal and ocean currents both to replenish existing stands and to establish new ones. The direction they travel depends on sea currents and land barriers, but the dispersal distance depends on the time that propagules remain buoyant and viable. This is expected to differ for each species. Similarly, each species will also differ in establishment success and growth development rate, and each has tolerance limits and growth responses which are apparently unique. Such attributes are presumably responsible for the characteristic distributional ranges of each species, as each responds to the environmental, physical and biotic settings they might occupy. In practice, species are often ordered by the interplay of different factors along environmental gradients, and these may conveniently be considered at four geographic scales-global, regional, estuarine and intertidal. We believe these influencing factors act similarly around the world, and to demonstrate this point, we present examples of distributional gradients from the two global biogeographic regions, the Atlantic East Pacific and the Indo-West Pacific.

Modification of the in vivo four-point loading model for studying mechanically induced bone adaptation

We modified the noninvasive, in vivo technique for strain application in the tibiae of rats (Turner et al,, Bone 12:73-79, 1991), The original model applies four-point bending to right tibiae via an open-loop, stepper-motor-driven spring linkage, Depending on the magnitude of applied load, the model produces new bone formation at periosteal (Ps) or endocortical surfaces (Ec.S). Due to the spring linkage, however, the range of frequencies at which loads can be applied is limited. The modified system replaces this design with an electromagnetic vibrator. A load transducer in series with the loading points allows calibration, the loaders' position to be adjusted, and cyclic loading completed under load central as a closed servo-loop. Two experiments were conducted to validate the modified system: (1) a strain gauge was applied to the lateral surface of the right tibia of 5 adult female rats and strains measured at applied loads from 10 to 60 N; and (2) the bone formation response was determined in 28 adult female Sprague-Dawley rats. Loading was applied as a haversine wave with a frequency of 2 Hz for 18 sec, every second day for 10 days. Peak bending loads mere applied at 33, 40, 52, and 64 N, and a sham-loading group tr as included at 64 N, Strains in the tibiae were linear between 10 and 60 N, and the average peak strain at the Ps.S at 60 N was 2664 +/- 250 microstrain, consistent with the results of Turner's group. Lamellar bone formation was stimulated at the Ec.S by applied bending, but not by sham loading. Bending strains above a loading threshold of 40 N increased Ec Lamellar hone formation rate, bone forming surface, and mineral apposition rate with a dose response similar to that reported by Turner et al, (J Bone Miner Res 9:87-97, 1994). We conclude that the modified loading system offers precision for applied loads of between 0 and 70 N, versatility in the selection of loading rates up to 20 Hz, and a reproducible bone formation response in the rat tibia, Adjustment of the loader also enables study of mechanical usage in murine tibia, an advantage with respect to the increasing variety of transgenic strains available in bone and mineral research. (Bone 23:307-310; 1998) (C) 1998 by Elsevier Science Inc. All rights reserved.

Tetrachromacy, oil droplets and bird plumage colours

There is a growing body of data on avian eyes, including measurements of visual pigment and oil droplet spectral absorption, and of receptor densities and their distributions across the retina. These data are sufficient to predict psychophysical colour discrimination thresholds for light-adapted eyes, and hence provide a basis for relating eye design to visual needs. We examine the advantages of coloured oil droplets, UV vision and tetrachromacy for discriminating a diverse set of avian plumage spectra under natural illumination. Discriminability is enhanced both by tetrachromacy and coloured oil droplets. Oil droplets may also improve colour constancy. Comparison of the performance of a pigeon's eye, where the shortest wavelength receptor peak is at 410 nm, with that of the passerine Leiothrix, where the ultraviolet-sensitive peak is at 365 nm, generally shows a small advantage to the latter, but this advantage depends critically on the noise level in the sensitivity mechanism and on the set of spectra being viewed.

Development of composite adsorbents of carbon and intercalated clay for N2 and O2 adsorption: A preliminary study

Composite adsorbents of carbon and alumina intercalated montmorillonite were prepared and characterized by adsorption of N-2 and O-2 at various temperatures. The effects of pyrolysis, temperature, heating rate, subsequent degassing, and doping of cations and anions were investigated. The adsorption capacities of the composite adsorbents developed at higher temperatures (0 and -79 degrees C) are found to be larger than those of normal alumina pillared clays. The experimental results showed that the framework of these adsorbents is made of alumina particles and clay sheets while the pyrolyzed carbon distributes in the space of interlayers and interpillars. The pores between the carbon particles, clay sheets, and alumina pillars are very narrow with very strong adsorption forces, leading to enhanced adsorption capacities at 0 and -79 degrees C. The composite adsorbents exhibit features similar to those of carbonaceous adsorbents. Their pore structures, adsorption capacities, and selectivities to oxygen can be tailored by a controlled degassing procedure. Meanwhile, ions can be doped into the adsorbents to modify their adsorption properties, as usually observed for oxide adsorbents like zeolite and pillared clays. Such flexibility in pore structure tailoring is a potential advantage of the composite adsorbents developed for their adsorption and separation applications. (C) 1999 Academic Press.

The foveal photoreceptor mosaic in the pipefish, Corythoichthyes paxtoni (Syngnathidae, Teleostei)

The foveal and non-foveal retinal regions of the pipefish, Corythoichthyes paxtoni (Syngnathidae, Teleostei) are examined at the level of the light and electron microscopes. The pipefish possesses a deep, pit (convexiclivate) fovea which, although lacking the displacement of the inner retinal layers as described in other vertebrate foveae, is characterised by the exclusion of rods, a marked increase in the density of photoreceptors and a regular square mosaic of four double cones surrounding a central single cone. In the perifoveal and peripheral retinal regions, the photoreceptor mosaic is disrupted by the insertion of large numbers of rods, which reduce spatial resolving power but may uniformly increase sensitivity for off-axis rays. In addition to a temporal fovea subtending the frontal binocular field, there is also a central area centralis subtending the monocular visual field. Based on morphological comparisons with other foveate teleosts, four foveal types are characterised and foveal function discussed with respect to the theoretical advantage of a regular square mosaic.

Modelling the large deformations in stratified media - the Cosserat continuum approach

Methods employing continuum approximation in describing the deformation of layered materials possess a clear advantage over explicit models, However, the conventional implicit models based on the theory of anisotropic continua suffers from certain difficulties associated with interface slip and internal instabilities. These difficulties can be remedied by considering the bending stiffness of the layers. This implies the introduction of moment (couple) stresses and internal rotations, which leads to a Cosserat-type theory. In the present model, the behaviour of the layered material is assumed to be linearly elastic; the interfaces are assumed to be elastic perfectly plastic. Conditions of slip or no slip at the interfaces are detected by a Coulomb criterion with tension cut off at zero normal stress. The theory is valid for large deformation analysis. The model is incorporated into the finite element program AFENA and validated against analytical solutions of elementary buckling problems in layered medium. A problem associated with buckling of the roof and the floor of a rectangular excavation in jointed rock mass under high horizontal in situ stresses is considered as the main application of the theory. Copyright (C) 1999 John Wiley & Sons, Ltd.

Moisture is required for the termination of egg diapause in the chrysomelid beetle, Homichloda barkeri

Four factors (moisture, light regime, temperature, food type) were examined for their effects on the embryonic diapause of Homichloda (Weiseana) barkeri (Jacoby) (Coleoptera: Chrysomelidae), a biocontrol agent for prickly acacia, Acacia nilotica (L.) Willdenew ex Delile (Mimosaceae). Moisture is critical for termination of diapause. A single wetting of eggs resulted in a low hatch rate while a sequence of wetting events followed by periods of dryness produced a high hatch rate. A relatively constant proportion of embryos within each batch initiated development at each wetting event, with hatching complete after the eighth wetting event in these trials. An extended interval between wetting events, tested at up to 23 days, did not result in a decreased overall hatch rate. A threshold time of exposure to moisture of between 3 to 6 h is required before development proceeds. The response of eggs to the moisture regime is seen as a strategy for taking advantage of available food after rainfall by terminating diapause, rather than merely a quiescent response to the absence of moisture. Temperature affected development time and the proportion of eggs that developed. Experimental manipulations of photoperiod and host-plant availability showed no effect on embryonic development.

Information internalization and hurdle rates in small and medium enterprise internationalization

We investigate the role of information in the internationalization of small and medium enterprises (SMEs). Information internalization is fundamentally antecedent to SME internationalization and is being facilitated increasingly by recent important trends. We offer a conceptual explanation and related propositions on information internalization, emphasizing hurdle rate theory for ascertaining the acceptability of firms' internationalization projects.

A new approach to current and noise in double quantum dot systems

We use a quantum master equation to describe transport in double-dot devices. The coherent dot-to-dot coupling affects the noise spectra strongly. For phonon-assisted tunneling, the calculated current spectra are consistent with those of experiments. The model shows that quantum stochastic theory may he applied to some advantage in mesoscopic electronic systems. (C) 2000 Elsevier Science B.V. All rights reserved.

Computation of bifurcation boundaries for power systems: A new Delta-plane method

This paper is devoted to the problems of finding the load flow feasibility, saddle node, and Hopf bifurcation boundaries in the space of power system parameters. The first part contains a review of the existing relevant approaches including not-so-well-known contributions from Russia. The second part presents a new robust method for finding the power system load flow feasibility boundary on the plane defined by any three vectors of dependent variables (nodal voltages), called the Delta plane. The method exploits some quadratic and linear properties of the load now equations and state matrices written in rectangular coordinates. An advantage of the method is that it does not require an iterative solution of nonlinear equations (except the eigenvalue problem). In addition to benefits for visualization, the method is a useful tool for topological studies of power system multiple solution structures and stability domains. Although the power system application is developed, the method can be equally efficient for any quadratic algebraic problem.