Transport Properties and Novel Sensing Applications of Organic Semiconducting Crystals

The present thesis is focused on the study of Organic Semiconducting Single Crystals (OSSCs) and crystalline thin films. In particular solution-grown OSSC, e.g. 4-hdroxycyanobenzene (4HCB) have been characterized in view of their applications as novel sensors of X-rays, gamma-rays, alpha particles radiations and chemical sensors. In the field of ionizing radiation detection, organic semiconductors have been proposed so far mainly as indirect detectors, i.e. as scintillators or as photodiodes. I first study the performance of 4HCB single crystals as direct X-ray detector i.e. the direct photon conversion into an electrical signal, assessing that they can operate at room temperature and in atmosphere, showing a stable and linear response with increasing dose rate. A dedicated study of the collecting electrodes geometry, crystal thickness and interaction volume allowed us to maximize the charge collection efficiency and sensitivity, thus assessing how OSSCs perform at low operating voltages and offer a great potential in the development of novel ionizing radiation sensors. To better understand the processes generating the observed X-ray signal, a comparative study is presented on OSSCs based on several small-molecules: 1,5-dinitronaphthalene (DNN), 1,8-naphthaleneimide (NTI), Rubrene and TIPS-pentacene. In addition, the proof of principle of gamma-rays and alpha particles has been assessed for 4HCB single crystals. I have also carried out an investigation of the electrical response of OSSCs exposed to vapour of volatile molecules, polar and non-polar. The last chapter deals with rubrene, the highest performing molecular crystals for electronic applications. We present an investigation on high quality, millimeter-sized, crystalline thin films (10 – 100 nm thick) realized by exploiting organic molecular beam epitaxy on water-soluble substrates. Space-Charge-Limited Current (SCLC) and photocurrent spectroscopy measurements have been carried out. A thin film transistor was fabricated onto a Cytop® dielectric layer. The FET mobility exceeding 2 cm2/Vs, definitely assess the quality of RUB films.

Template-assisted patterning of functional polymers

In this thesis, anodic aluminum oxide (AAO) membranes, which provide well-aligned uniform mesoscopic pores with adjustable pore parameters, were fabricated and successfully utilized as templates for the fabrication of functional organic nanowires, nanorods and the respective well-ordered arrays. The template-assisted patterning technique was successfully applied for the realization of different objectives:rnHigh-density and well-ordered arrays of hole-conducting nanorods composed of cross-linked triphenylamine (TPA) and tetraphenylbenzidine (TPD) derivatives on conductive substrates like ITO/glass have been successfully fabricated. By applying a freeze-drying technique to remove the aqueous medium after the wet-chemical etching of the template, aggregation and collapsing of the rods was prevented and macroscopic areas of perfectly freestanding nanorods were feasible. Based on the hole-conducting nanorod arrays and their subsequent embedding into an electron-conducting polymer matrix via spin-coating, a novel routine concept for the fabrication of well-ordered all-organic bulk heterojunction for organic photovoltaic applications was successfully demonstrated. The increased donor/acceptor interface of the fabricated devices resulted in a remarkable increase of the photoluminescence quenching compared to a planar bilayer morphology. Further, the fundamental working principle of the templating approach for the solution-based all-organic photovoltaic device was demonstrated for the first time.rnFurthermore, in order to broaden the applicability of patterned surfaces, which are feasible via the template-based patterning of functional materials, AAO with hierarchically branched pores were fabricated and utilized as templates. By pursuing the common templating process hierarchically polymeric replicas, which show remarkable similarities with interesting biostructures, like the surface of the lotus leaf and the feet of a gecko, were successfully prepared.rnIn contrast to the direct infiltration of organic functional materials, a novel route for the fabrication of functional nanowires via post-modification of reactive nanowires was established. Therefore, reactive nanowires based on cross-linked pentafluorophenylesters were fabricated by utilizing AAO templates. The post-modification with fluorescent dyes was demonstrated. Furthermore, reactive wires were converted into well-dispersed poly(N-isopropylacrylamide) (PNIPAM) hydrogels, which exhibit a thermal-responsive reversible phase transition. The reversible thermal-responsible swelling of the PNIPAM nanowires exhibited a more than 50 % extended length than in the collapsed PNIPAM state. rnLast but not least, the shape-anisotropic pores of AAO were utilized to uniformly align the mesogens of a nematic liquid crystalline elastomer. Liquid crystalline nanowires with a narrow size distribution and uniform orientation of the liquid crystalline material were fabricated. It was shown that during the transition from the nematic to the isotropic phase the rod’s length shortened by roughly 40 percent. As such these liquid crystalline elastomeric nanowires may find application, as wire-shaped nanoactuators in various fields of research, like lab-on-chip systems, micro fluidics and biomimetics.rn

EPR spectroscopy as a tool for the elucidation of non-covalent structuring principles in complex soft matter

This thesis aims at connecting structural and functional changes of complex soft matter systems due to external stimuli with non-covalent molecular interaction profiles. It addresses the problem of elucidating non-covalent forces as structuring principle of mainly polymer-based systems in solution. The structuring principles of a wide variety of complex soft matter types are analyzed. In many cases this is done by exploring conformational changes upon the exertion of external stimuli. The central question throughout this thesis is how a certain non-covalent interaction profile leads to solution condition-dependent structuring of a polymeric system.rnTo answer this question, electron paramagnetic resonance (EPR) spectroscopy is chosen as the main experimental method for the investigation of the structure principles of polymers. With EPR one detects only the local surroundings or environments of molecules that carry an unpaired electron. Non-covalent forces are normally effective on length scales of a few nanometers and below. Thus, EPR is excellently suited for their investigations. It allows for detection of interactions on length scales ranging from approx. 0.1 nm up to 10 nm. However, restriction to only one experimental technique likely leads to only incomplete pictures of complex systems. Therefore, the presented studies are frequently augmented with further experimental and computational methods in order to yield more comprehensive descriptions of the systems chosen for investigation.rnElectrostatic correlation effects in non-covalent interaction profiles as structuring principles in colloid-like ionic clusters and DNA condensation are investigated first. Building on this it is shown how electrostatic structuring principles can be combined with hydrophobic ones, at the example of host-guest interactions in so-called dendronized polymers (denpols).rnSubsequently, the focus is shifted from electrostatics in dendronized polymers to thermoresponsive alkylene oxide-based materials, whose structuring principles are based on hydrogen bonds and counteracting hydrophobic interactions. The collapse mechanism in dependence of hydrophilic-hydrophobic balance and topology of these polymers is elucidated. Complementarily the temperature-dependent phase behavior of elastin-like polypeptides (ELPs) is investigated. ELPs are the first (and so far only) class of compounds that is shown to feature a first-order inverse phase transition on nanoscopic length scales.rnFinally, this thesis addresses complex biological systems, namely intrinsically disordered proteins (IDPs). It is shown that the conformational space of the IDPs Osteopontin (OPN), a cytokine involved in metastasis of several kinds of cancer, and BASP1 (brain acid soluble protein one), a protein associated with neurite outgrowth, is governed by a subtle interplay between electrostatic forces, hydrophobic interaction, system entropy and hydrogen bonds. Such, IDPs can even sample cooperatively folded structures, which have so far only been associated with globular proteins.

Development and optimisation of novel 68 Ga-folates - towards early diagnosis of ovarian cancer

Der Folsäure-basierte Radiotracer Etarfolatide (99mTc-EC 20) hat in der Vergangenheit sehr vielversprechende Ergebnisse im Bereich der frühzeitigen Diagnostik von Ovarialkarzinomen gezeigt. Einzelphotonen-Emissionscomputertomographie (SPECT) erlaubt dabei eine Visualisierung der Krankheit in einem sehr frühen Stadium – ermöglicht wird dies durch Folsäure, welche als Target Vektor dient. Um das erfolgreiche Prinzip der Radiofolate auf die Positronen-Emissionstomographie (PET) zu übertragen, welche eine noch höhere räumliche Auflösung ermöglicht, wurden in den letzten fünf Jahren bereits 18F-folate entwickelt. Deren hepatobiliären Exkretionsmuster, verursacht durch die relativ hohe Lipophilie der Strukturen, entsprachen jedoch nicht den Anforderungen. Eine optimierte Bioverteilung der Tracer in vivo kann durch eine generelle Erhöhung der Polarität erfolgen. Die Kombination aus einem polaren 68Ga-Komplex mit Folsäure als Target Vektor stellte den Fokus dieses Projektes dar. Ziel war die Entwicklung eines Radiofolates mit der Tendenz einer raschen renalen Ausscheidung und verringerter hepatobiliärer Anreicherung. Dazu wurde Folsäure regiospezifisch über ihre y-Säure an verschiedene bifunktionelle Chelatoren (BFCs) gekoppelt. Vier verschiedene Reaktionstypen wurden gewählt und durchgeführt: Cu-katalysierte sowie Cu-freie Click Reaktion, Amindbindung und Thioharnstoff Bildung. Es wurden sechs verschiedene Derivate erhalten und mit 68Ga radiomarkiert.

Reparation and enforcement of judgments : a comparative analysis of the European and Inter-American human rights systems

The inter-American human rights system has been conceived following the example of the European system under the European Convention on Human Rights (ECHR) before it was modified by Protocol No 11. However, two important differences exist. First, the authority of the European Court of Human Rights (ECtHR) to order reparation has been strictly limited by the principle of subsidiarity. Thus, the ECtHR's main function is to determine whether the ECHR has been violated. Beyond the declaratory effect of its judgments, according to Article 41 ECHR, it may only "afford just satisfaction to the injured party". The powers of the Inter-American Court of Human Rights (IACtHR) were conceived in a much broader fashion in Article 63 of the American Convention on Human Rights (ACHR), giving the Court the authority to order a variety of individual and general measures aimed at obtaining restitutio in integrum. The first main part of this thesis shows how both Courts have developed their reparation practice and examines the advantages and disadvantages of each approach. Secondly, the ECtHR's rather limited reparation powers have, interestingly, been combined with an elaborate implementation system that includes several of the Council of Europe's organs, principally the Committee of Ministers. In the Inter-American System, no dedicated mechanism was implemented to oversee compliance with the IACtHR's judgments. The ACHR limits itself to inviting the Court to point out in its annual reports the cases that have not been complied with and to propose measures to be adopted by the General Assembly of the Organization of American States. The General Assembly, however, hardly ever took action. The IACtHR has therefore filled this gap by developing a proper procedure to oversee compliance with its judgments. Both the European and the American solutions to ensure compliance are presented and compared in the second main part of this thesis. Finally, based on the results of both main parts, a comparative analysis of the reparation practice and the execution results in both human rights systems is being provided, aimed at developing proposals for the improvement of the functioning of either human rights protection system.

Design and implementation of an anonymous peer-to-peer iaas cloud

Cloud services are becoming ever more important for everyone's life. Cloud storage? Web mails? Yes, we don't need to be working in big IT companies to be surrounded by cloud services. Another thing that's growing in importance, or at least that should be considered ever more important, is the concept of privacy. The more we rely on services of which we know close to nothing about, the more we should be worried about our privacy. In this work, I will analyze a prototype software based on a peer to peer architecture for the offering of cloud services, to see if it's possible to make it completely anonymous, meaning that not only the users using it will be anonymous, but also the Peers composing it will not know the real identity of each others. To make it possible, I will make use of anonymizing networks like Tor. I will start by studying the state of art of Cloud Computing, by looking at some real example, followed by analyzing the architecture of the prototype, trying to expose the differences between its distributed nature and the somehow centralized solutions offered by the famous vendors. After that, I will get as deep as possible into the working principle of the anonymizing networks, because they are not something that can just be 'applied' mindlessly. Some de-anonymizing techniques are very subtle so things must be studied carefully. I will then implement the required changes, and test the new anonymized prototype to see how its performances differ from those of the standard one. The prototype will be run on many machines, orchestrated by a tester script that will automatically start, stop and do all the required API calls. As to where to find all these machines, I will make use of Amazon EC2 cloud services and their on-demand instances.

Hydraulic evaluation of the gyro electric wave energy converter

Motivation Thanks for a scholarship offered by ALma Mater Studiorum I could stay in Denmark for six months during which I could do physical tests on the device Gyro PTO at the Departmet of Civil Engineering of Aalborg University. Aim The goal of my thesis is an hydraulic evaluation of the device: Gyro PTO, a gyroscopic device for conversion of mechanical energy in ocean surface waves to electrical energy. The principle of the system is the application of the gyroscopic moment of flywheels equipped on a swing float excited by waves. The laboratory activities were carried out by: Morten Kramer, Jan Olsen, Irene Guaraldi, Morten Thøtt, Nikolaj Holk. The main purpose of the tests was to investigate the power absorption performance in irregular waves, but testing also included performance measures in regular waves and simple tests to get knowledge about characteristics of the device, which could facilitate the possibility of performing numerical simulations and optimizations. Methodology To generate the waves and measure the performance of the device a workstation was created in the laboratory. The workstation consist of four computers in each of wich there was a different program. Programs have been used : Awasys6, LabView, Wave lab, Motive optitrack, Matlab, Autocad Main Results Thanks to the obtained data with the tank testing was possible to make the process of wave analisys. We obtained significant wave height and period through a script Matlab and then the values of power produced, and energy efficiency of the device for two types of waves: regular and irregular. We also got results as: physical size, weight, inertia moments, hydrostatics, eigen periods, mooring stiffness, friction, hydrodynamic coefficients etc. We obtained significant parameters related to the prototype in the laboratory after which we scale up the results obtained for two future applications: one in Nissun Brending and in the North Sea. Conclusions The main conclusion on the testing is that more focus should be put into ensuring a stable and positive power output in a variety of wave conditions. In the irregular waves the power production was negative and therefore it does not make sense to scale up the results directly. The average measured capture width in the regular waves was 0.21 m. As the device width is 0.63 m this corresponds to a capture width ratio of: 0.21/0.63 * 100 = 33 %. Let’s assume that it is possible to get the device to produce as well in irregular waves under any wave conditions, and lets further assume that the yearly absorbed energy can be converted into electricity at a PTO-efficiency of 90 %. Under all those assumptions the results in table are found, i.e. a Nissum Bredning would produce 0.87 MWh/year and a North Sea device 85 MWh/year.

Benchmarking in the SWISSspine registry: results of 52 Dynardi lumbar total disc replacements compared with the data pool of 431 other lumbar disc prostheses

The SWISSspine registry is the first mandatory registry of its kind in the history of Swiss orthopaedics and it follows the principle of "coverage with evidence development". Its goal is the generation of evidence for a decision by the Swiss federal office of health about reimbursement of the concerned technologies and treatments by the basic health insurance of Switzerland. Recently, developed and clinically implemented, the Dynardi total disc arthroplasty (TDA) accounted for 10% of the implanted lumbar TDAs in the registry. We compared the outcomes of patients treated with Dynardi to those of the recipients of the other TDAs in the registry. Between March 2005 and October 2009, 483 patients with single-level TDA were documented in the registry. The 52 patients with a single Dynardi lumbar disc prosthesis implanted by two surgeons (CE and OS) were compared to the 431 patients who received one of the other prostheses. Data were collected in a prospective, observational multicenter mode. Surgery, implant, 3-month, 1-year, and 2-year follow-up forms as well as comorbidity, NASS and EQ-5D questionnaires were collected. For statistical analyses, the Wilcoxon signed-rank test and chi-square test were used. Multivariate regression analyses were also performed. Significant and clinically relevant reduction of low back pain and leg pain as well as improvement in quality of life was seen in both groups (P < 0.001 postop vs. preop). There were no inter-group differences regarding postoperative pain levels, intraoperative and follow-up complications or revision procedures with a new hospitalization. However, significantly more Dynardi patients achieved a minimum clinically relevant low back pain alleviation of 18 VAS points and a quality of life improvement of 0.25 EQ-5D points. The patients with Dynardi prosthesis showed a similar outcome to patients receiving the other TDAs in terms of postoperative low back and leg pain, complications, and revision procedures. A higher likelihood for achieving a minimum clinically relevant improvement of low back pain and quality of life in Dynardi patients was observed. This difference might be due to the large number of surgeons using other TDAs compared to only two surgeons using the Dynardi TDA, with corresponding variations in patient selection, patient-physician interaction and other factors, which cannot be assessed in a registry study.

In vivo evaluation of the first dedicated combined flow-restoration and mechanical thrombectomy device in a swine model of acute vessel occlusion

The use of self-expanding retrievable stents is an emerging and promising treatment strategy for acute stroke treatment. The concept combines the advantages of stent deployment with immediate flow-restoration and of mechanical thrombectomy with definitive thrombus removal. The present study was performed to gain more knowledge about the principle of combined flow restoration and thrombectomy in an established animal model using radiopaque thrombi evaluating efficiency, thrombus-device interaction and possible complications of the first dedicated flow-restoration and mechanical thrombectomy device.

Macro Monte Carlo for dose calculation of proton beams

Although the Monte Carlo (MC) method allows accurate dose calculation for proton radiotherapy, its usage is limited due to long computing time. In order to gain efficiency, a new macro MC (MMC) technique for proton dose calculations has been developed. The basic principle of the MMC transport is a local to global MC approach. The local simulations using GEANT4 consist of mono-energetic proton pencil beams impinging perpendicularly on slabs of different thicknesses and different materials (water, air, lung, adipose, muscle, spongiosa, cortical bone). During the local simulation multiple scattering, ionization as well as elastic and inelastic interactions have been taken into account and the physical characteristics such as lateral displacement, direction distributions and energy loss have been scored for primary and secondary particles. The scored data from appropriate slabs is then used for the stepwise transport of the protons in the MMC simulation while calculating the energy loss along the path between entrance and exit position. Additionally, based on local simulations the radiation transport of neutrons and the generated ions are included into the MMC simulations for the dose calculations. In order to validate the MMC transport, calculated dose distributions using the MMC transport and GEANT4 have been compared for different mono-energetic proton pencil beams impinging on different phantoms including homogeneous and inhomogeneous situations as well as on a patient CT scan. The agreement of calculated integral depth dose curves is better than 1% or 1 mm for all pencil beams and phantoms considered. For the dose profiles the agreement is within 1% or 1 mm in all phantoms for all energies and depths. The comparison of the dose distribution calculated using either GEANT4 or MMC in the patient also shows an agreement of within 1% or 1 mm. The efficiency of MMC is up to 200 times higher than for GEANT4. The very good level of agreement in the dose comparisons demonstrate that the newly developed MMC transport results in very accurate and efficient dose calculations for proton beams.

The Syntax of the EPP in Irish

In this paper, I will provide a detailed analysis of the EPP, a principle of theoretical syntax, in Modern Irish. I will document previous scholarship on this issue to give a comprehensive view of ways of reconciling the syntax with the language data, as language data is key to testing theoretical predictions. I will also provide my own model incorporating the EPP into Irish. First, I will provide necessary information about the background and development of the EPP and the Minimalist system in syntax, as well as a discussion of the Irish language and the features which make it relevant to the study of the EPP. Then, I will present the models of Irish and the considerations of the EPP which have shaped and influenced my own. These models include both instances of altering the definition of the EPP to increase its universal application and of adapting models of VSO languages to fit the prevailing definition of the EPP. Lastly, I will detail my own model for Irish sentence structure, which suggests an alternate subject position in the syntax which would allow for the EPP to adapt to fit VSO word order. An analysis of passive and the unaccusative constructions, as well as support from contemporary syntactic theory, will support this model. To complete my consideration of Irish and the EPP, I will also provide a discussion of whether of not pleonastic pronouns function in Irish and how they would be accounted for in my model.

An Analysis of Capacities, Moral Hierarchies, and the Moral Status of Non-Human Animals in Contemporary Animal Rights Work

The primary objective of this thesis is to demonstrate the pernicious impact that moral hierarchies have on our perception and subsequent treatment of non-human animals. Moral hierarchies in general are characterized by a dynamic in which one group is considered to be fundamentally superior to a lesser group. This thesis focuses specifically on the moral hierarchies that arise when humans are assumed to be superior to non-human animals in virtue of their advanced mental capabilities. The operative hypothesis of this thesis is essentially that moral hierarchies thwart the provision of justice to non-human animals in that they function as a justification for otherwise impermissible actions. When humans are assumed to be fundamentally superior to non-human animals then it becomes morally permissible for humans to kill non-human animals and utilize them as mere instrumentalities. This thesis is driven primarily by an in-depth analysis of the approaches to animal rights that are provided by Peter Singer, Tom Regan, and Gary Francione. Each of these thinkers claim that they overcome anthropocentrism and provide approaches that preclude the establishment of a moral hierarchy. One of the major findings of this thesis, however, is that Singer and Regan offer approaches that remain highly anthropocentric despite the fact that each thinker claims that they have overcome anthropocentrism. The anthropocentrism persists in these respective approaches in that each thinkers gives humans Regan and Singer have different conceptions of the criteria that are required to afford a being moral worth, but they both give preference to beings that have the cognitive ability to form desires regarding the future.. As a result, a moral hierarchy emerges in which humans are regarded to be fundamentally superior. Francione, however, provides an approach that does not foster a moral hierarchy. Francione creates such an approach by applying the principle of equal consideration of interests in a consistent manner. Moreover, Francione argues that mere sentience is both a necessary and sufficient condition for being eligible and subsequently receiving moral consideration. The upshot of this thesis is essentially that the moral treatment of animals is not compatible with the presence of a moral hierarchy. As a result, this thesis demonstrates that future approaches to animal rights must avoid the establishment of moral hierarchies. The research and analysis within this thesis demonstrates that this is not a possibility, however, unless all theories of justice that are to accommodate animals abandon the notion that cognition matters morally.

Questions of Life and Death

The research started with a definition of the general ethical background to be applied in bioethical discussions, particularly regarding aspects of morality that have to be enforced by the community. Only those moral beliefs that can be accepted by consensus in a free discussion can be enforced. It follows that the basic principle of a well ordered society is the equality (and possible upwards extension) of the basic liberties. Therefore, whenever it is possible to respect the principle of autonomy in matters of bioethics (here including questions of abortion, assisted procreation, genetics, organ transplantation and euthanasia) this must be done. On the other hand, there are some common values that can be defended in a free dialogue, values that are needed in order to guarantee stable cooperation in a political society. These values include the respect for human life, which implies the respect for human life in all its forms. This leads to the conclusion that people who are able to be part of the system of cooperation in a political society have rights which are dominant in moral considerations. In all cases where there is no conflict between these rights and the value of life as manifested in human individuals who are not able participate in social cooperation, considerations of the value of the life of the latter must be an important moral consideration. This implies that embryo experimentation should be permitted in order to develop scientific advances needed to save human life, but embryos must not be used for trivial reasons or for the cosmetic industry.

The Dynamics of the Policies of Ethnic Cleansing in Silesia in the Nineteenth and Twentieth Centuries

Through studying German, Polish and Czech publications on Silesia, Mr. Kamusella found that most of them, instead of trying to objectively analyse the past, are devoted to proving some essential "Germanness", "Polishness" or "Czechness" of this region. He believes that the terminology and thought-patterns of nationalist ideology are so deeply entrenched in the minds of researchers that they do not consider themselves nationalist. However, he notes that, due to the spread of the results of the latest studies on ethnicity/nationalism (by Gellner, Hobsbawm, Smith, Erikson Buillig, amongst others), German publications on Silesia have become quite objective since the 1980s, and the same process (impeded by under funding) has been taking place in Poland and the Czech Republic since 1989. His own research totals some 500 pages, in English, presented on disc. So what are the traps into which historians have been inclined to fall? There is a tendency for them to treat Silesia as an entity which has existed forever, though Mr. Kamusella points out that it emerged as a region only at the beginning of the 11th century. These same historians speak of Poles, Czechs and Germans in Silesia, though Mr. Kamusella found that before the mid-19th century, identification was with an inhabitant's local area, religion or dynasty. In fact, a German national identity started to be forged in Prussian Silesia only during the Liberation War against Napoleon (1813-1815). It was concretised in 1861 in the form of the first Prussian census, when the language a citizen spoke was equated with his/her nationality. A similar census was carried out in Austrian Silesia only in 1881. The censuses forced the Silesians to choose their nationality despite their multiethnic multicultural identities. It was the active promotion of a German identity in Prussian Silesia, and Vienna's uneasy acceptance of the national identities in Austrian Silesia which stimulated the development of Polish national, Moravian ethnic and Upper Silesian ethnic regional identities in Upper Silesia, and Polish national, Czech national, Moravian ethnic and Silesian ethnic identities in Austrian Silesia. While traditional historians speak of the "nationalist struggle" as though it were a permanent characteristic of Silesia, Mr. Kamusella points out that such a struggle only developed in earnest after 1918. What is more, he shows how it has been conveniently forgotten that, besides the national players, there were also significant ethnic movements of Moravians, Upper Silesians, Silesians and the tutejsi (i.e. those who still chose to identify with their locality). At this point Mr. Kamusella moves into the area of linguistics. While traditionally historians have spoken of the conflicts between the three national languages (German, Polish and Czech), Mr Kamusella reminds us that the standardised forms of these languages, which we choose to dub "national", were developed only in the mid-18th century, after 1869 (when Polish became the official language in Galicia), and after the 1870s (when Czech became the official language in Bohemia). As for standard German, it was only widely promoted in Silesia from the mid 19th century onwards. In fact, the majority of the population of Prussian Upper Silesia and Austrian Silesia were bi- or even multilingual. What is more, the "Polish" and "Czech" Silesians spoke were not the standard languages we know today, but a continuum of West-Slavic dialects in the countryside and a continuum of West-Slavic/German creoles in the urbanised areas. Such was the linguistic confusion that, from time to time, some ethnic/regional and Church activists strove to create a distinctive Upper Silesian/Silesian language on the basis of these dialects/creoles, but their efforts were thwarted by the staunch promotion of standard German, and after 1918, of standard Polish and Czech. Still on the subject of language, Mr. Kamusella draws attention to a problem around the issue of place names and personal names. Polish historians use current Polish versions of the Silesian place names, Czechs use current Polish/Czech versions of the place names, and Germans use the German versions which were in use in Silesia up to 1945. Mr. Kamusella attempted to avoid this, as he sees it, nationalist tendency, by using an appropriate version of a place name for a given period and providing its modern counterpart in parentheses. In the case of modern place names he gives the German version in parentheses. As for the name of historical figures, he strove to use the name entered on the birth certificate of the person involved, and by doing so avoid such confusion as, for instance, surrounds the Austrian Silesian pastor L.J. Sherschnik, who in German became Scherschnick, in Polish, Szersznik, and in Czech, Sersnik. Indeed, the prospective Silesian scholar should, Mr. Kamusella suggests, as well as the three languages directly involved in the area itself, know English and French, since many documents and books on the subject have been published in these languages, and even Latin, when dealing in depth with the period before the mid-19th century. Mr. Kamusella divides the policies of ethnic cleansing into two categories. The first he classifies as soft, meaning that policy is confined to the educational system, army, civil service and the church, and the aim is that everyone learn the language of the dominant group. The second is the group of hard policies, which amount to what is popularly labelled as ethnic cleansing. This category of policy aims at the total assimilation and/or physical liquidation of the non-dominant groups non-congruent with the ideal of homogeneity of a given nation-state. Mr. Kamusella found that soft policies were consciously and systematically employed by Prussia/Germany in Prussian Silesia from the 1860s to 1918, whereas in Austrian Silesia, Vienna quite inconsistently dabbled in them from the 1880s to 1917. In the inter-war period, the emergence of the nation-states of Poland and Czechoslovakia led to full employment of the soft policies and partial employment of the hard ones (curbed by the League of Nations minorities protection system) in Czechoslovakian Silesia, German Upper Silesia and the Polish parts of Upper and Austrian Silesia. In 1939-1945, Berlin started consistently using all the "hard" methods to homogenise Polish and Czechoslovakian Silesia which fell, in their entirety, within the Reich's borders. After World War II Czechoslovakia regained its prewar part of Silesia while Poland was given its prewar section plus almost the whole of the prewar German province. Subsequently, with the active involvement and support of the Soviet Union, Warsaw and Prague expelled the majority of Germans from Silesia in 1945-1948 (there were also instances of the Poles expelling Upper Silesian Czechs/Moravians, and of the Czechs expelling Czech Silesian Poles/pro-Polish Silesians). During the period of communist rule, the same two countries carried out a thorough Polonisation and Czechisation of Silesia, submerging this region into a new, non-historically based administrative division. Democratisation in the wake of the fall of communism, and a gradual retreat from the nationalist ideal of the homogeneous nation-state with a view to possible membership of the European Union, caused the abolition of the "hard" policies and phasing out of the "soft" ones. Consequently, limited revivals of various ethnic/national minorities have been observed in Czech and Polish Silesia, whereas Silesian regionalism has become popular in the westernmost part of Silesia which remained part of Germany. Mr. Kamusella believes it is possible that, with the overcoming of the nation-state discourse in European politics, when the expression of multiethnicity and multilingualism has become the cause of the day in Silesia, regionalism will hold sway in this region, uniting its ethnically/nationally variegated population in accordance with the principle of subsidiarity championed by the European Union.

The Legal Protection of Fundamental Human Values in Central and Eastern Europe and Modern Biotechnology: Towards European Harmonization

The protection of the fundamental human values (life, bodily integrity, human dignity, privacy) becomes imperative with the rapid progress in modern biotechnology, which can result in major alterations in the genetic make-up of organisms. It has become possible to insert human genes into pigs so that their internal organs coated in human proteins are more suitable for transplantation into humans (xenotransplantation), and micro-organisms that cam make insulin have been created, thus changing the genetic make-up of humans. At the end of the 1980s, the Central and Eastern European (CEE) countries either initiated new legislation or started to amend existing laws in this area (clinical testing of drugs, experiments on man, prenatal genetic diagnosis, legal protection of the embryo/foetus, etc.). The analysis here indicates that the CEE countries have not sufficiently adjusted their regulations to the findings of modern biotechnology, either because of the relatively short period they have had to do so, or because there are no definite answers to the questions which modern biotechnology has raised (ethical aspects of xenotransplantation, or of the use of live-aborted embryonic or foetal tissue in neuro-transplantation, etc.). In order to harmonise the existing regulations in CEE countries with respect to the EU and supranational contexts, two critical issues should be taken into consideration. The first is the necessity for CEE countries to recognise the place of humans within the achievements of modern biotechnology (a broader affirmation of the principle of autonomy, an explicit ban on the violation of the genetic identity of either born or unborn life, etc.). The second concerns the definition of the status of different biotechnological procedures and their permissibility (gene therapy, therapeutic genomes, xenotransplantation, etc.). The road towards such answers may be more easily identified once all CEE countries become members of the Council of Europe and express their wish to join the EU, which in turn presupposes taking over the entire body of EU legislation.