Effect of temperature on incubation period, embryonic mortality, hatch rate, egg water loss and partridge chick weight (Rhynchotus rufescens)

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Phytase immobilization on modified electrodes for amperometric biosensing

Phytase (myo-inositol hexaphosphate phosphohydrolase) and phytic acid (myo-inositol hexaphosphate) play an important environmental role, in addition to being a health issue in food industry. Phytic acid is antinutritional due to its ability to chelate metal ions and may also react with proteins decreasing their bioavailability. In this work, we produced biosensors with phytase immobilized in Layer-by-Layer (LbL) films, which could detect phytic acid with a detection limit of 0.19 mmol L-1, which is sufficient to detect phytic acid in seeds of grains and vegetables. The biosensosrs consisted of LbL films containing up to eight bilayers of phytase alternated with poly(allylamine) hydrochloride (PAH) deposited onto an indium-tin oxide (ITO) substrate modified with Prussian Blue. Amperometric detection was conducted in an acetate buffer solution (at pH 5.5) at room temperature, with the biosensor response attributed to the formation of phosphate ions. In subsidiary experiments with the currents measured at 0.0 V (vs. SCE), we demonstrated the absence of effects from some interferents, pointing to a good selectivity of the biosensor. (c) 2007 Elsevier B.V. All rights reserved.

Photo-induced electron trapping in indirect bandgap AlxGa1-xAs : Si at low temperature

A variation of photoconductivity excitation with wavelength is applied to Si-doped Al0.56Ga0.44As (indirect bandgap material) for a wide range of temperature. The lower the temperature the lower the photocurrent below 70 K. In the range 13-30 K there is a decrease in the photoconductivity spectrum slightly above the bandgap transition energy, followed by another increase in the conductivity. We interpret these results in the light of existing models and confirm the trapping by the X-valley effective mass state. which is responsible for attenuation of persistent photoconductivity below 70 K. A DX0 intermediate state which has non-negligible lifetime is proposed as responsible for the decrease in the photoconductivity with about 561 nm of wavelength of exciting light, in the investigated 13-30 g range.

Effects of the high temperature plasma immersion ion implantation (PIII) of nitrogen in AISI H13 steel

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Effect of light and temperature on seed germination in guava (Psidium guajava L. Myrtaceae)

The germination of seeds of Psidium guajava L. (Myrtaceae) is controlled by phytochrome. Guava seeds can germinate with at least one hour per day of irradiation of high red:far-red ratio light preceeded or followed by shade light, indicating that phytochrome B controls germination in these conditions. Under alternating temperatures, in a range of at least 5degreesC, seeds will germinate in darkness, suggesting that in gaps of the canopy, when seeds are covered by a thin layer of soil they will germinate once the alternating temperatures are experienced. Under these conditions phytochrome A is responsible for the control of guava seed germination.

Spontaneous vesicles of sodium dihexadecylphosphate in HEPES buffer

The formation of spontaneous vesicles of dihexadecylphosphate (DHP) in a HEPES buffered solution at pH 7.4, the size, morphology and melting temperature, obtained by cryogenic transmission electron microscopy (cryo-TEM) and differential scanning calorimetry (DSC), are reported. The vesicles were formed by simply mixing a 5.0 mM lipid-solvent mixture at a temperature (75 degrees C) safely above the higher melting temperature T-m = 70.4 degrees C of DHP. The vesicle diameter ranges from 100 to 332 nm and their geometry is spherical, faceted or oblong. T-m increases from 66.8 to 70.4 as DHP concentration is raised from 0.6 to 5.0 mM. (c) 2008 Elsevier B.V. All rights reserved.

Effect of citrate ions on the electrochemical behaviour of low-carbon steel in borate buffer solutions

The electrochemical behaviour of cold-rolled low carbon steel was studied on both active and passive potential regions in borate buffer solutions with and without the addition of sodium citrate (NaCit). In the active region anodic charges increased significantly and RCT values decreased with citrate, due to the formation of soluble complexes. In the passive potential region the film formed at +0.4 V in borate buffer solution with and without 0.010 M NaCit is probably enriched by Fe3O4 oxide, while films formed at +0.8 V are probably enriched by gamma-Fe2O3. The equivalent circuit [R-s(R(CT)Q)] fitted all experimental impedance data. (C) 2003 Elsevier Ltd. All rights reserved.

Ultrastructure of early mineral deposition during hyaline layer formation in rat molars

There is no consensus on whether the first mineralized layer, the hyaline layer, that is juxtaposed to root dentine is a variety of dentine or cementum or even a tissue of epithelial origin. Some suggest that there is no intermediate tissue between the acellular extrinsic fibre cementum (AEFC) and the root dentine. Here, to study hyaline layer formation and mineralization we examined by transmission electron microscopy the early stages of root development in upper molars from 10 to 13 day old Wistar rats. In addition to conventionally processed material, undemineralized and unstained sections were examined, which showed the deposition of fine mineral crystals in contact with the mineralized surface of root dentine. Early mineralization of the hyaline layer occurred in the region of the inner basement membrane, which persisted between the inner cellular layer of Hertwig's epithelial root sheath and the outer mineralized root dentine. When the root sheath began its fragment, collagen fibrils From the developing periodontal ligament began to insert into the mineralising hyaline layer, which was 0.5-0.8 mum wide. As the fragmentation of the root sheath HERS increased, more collagen fibrils appeared intermingled with the mineralising hyaline layer. In more advanced stages, when the hyaline layer had become fully mineralized and the formation of the AEFC began, the hyaline layer could no longer be identified. Thus, the hyaline layer is clearly discernible at early stages of periodontal development. Subsequently, it is masked by intermingling of cementum and dentine and therefore it is not possible to detect it in the formed roots of rat molars. (C) 2001 Elsevier B.V. Ltd. All rights reserved.

Structural and electrical properties of SrBi2Nb2O9 thin films prepared by chemical aqueous solution at low temperature

SrBi2Nb2O9 (SBN) thin films were prepared by the polymeric precursors method and deposited by dip coating onto Pt/Ti/SiO2/Si(100) substrates. The dip-coated films were specular and crack-free and crystallized during firing at 700 degrees C. Microstructure and morphological evaluation were followed by grazing incident X-ray diffraction (GIXRD), scanning electron microscopy (SEM) and atomic force microscopy (AFM). The films exhibited somewhat porous grain structure with rounded grains of about 100 nm. For the electrical measurements, gold electrodes of 300 mu m in diameter were sputter deposited on the top surface, forming a metal-ferroelectric-metal (MFM) configuration. The remanent polarization (P-r) and coercive field (E-c) were 5.6 mu C/cm(2) and 100 kV/cm, respectively. (C) 1999 Elsevier B.V. B.V. All rights reserved.

Effects of the high-temperature plasma immersion ion-implantation treatment on corrosion behavior of Ti-6Al1-4V

Nitrogen implantation into Ti alloys at higher temperatures improves their mechanical and corrosion resistance properties by forming a thicker nitride layer. In this paper, two different sets of Ti-6Al-4V samples were plasma immersion ion implantation (PIII)-treated using nitrogen plasma, varying the treatment time from 30 to 150 min (800 degrees C) and the process temperature from 400 degrees C to 800 degrees C (t = 60 min). Nanoindentation measurements of the PIII-treated samples at 800 C during 150 min showed the highest hardness value, 24 GPa, which is about four times bigger than untreated sample hardness. The N penetration at these conditions reached approximately 150 nm as analyzed by Auger spectroscopy. on the other hand, the lowest passive current density (3 x 10(-7) A. cm(-2)) was obtained for a PIII-treated sample during 30 min at higher temperature (800 degrees C). The corrosion resistance of this sample is almost the same as for the untreated specimen. Corrosion behavior evidenced that in strong oxidizing media, all PIII-treated samples are more corrosion resistant than the untreated one. PIII processing at higher temperatures promotes smoothing of the sample surface as observed by scanning electron microscopy (SEM). Grazing incidence X-ray diffraction analyses of the untreated samples identified the two typical Ti phases, Ti alpha and Ti beta. After the implantation, Ti2N and TiO2 phases were also detected.

Effect of temperature on the optical properties of GaAsSbN/GaAs single quantum wells grown by molecular-beam epitaxy

GaAsSbN/GaAs strained-layer single quantum wells grown on a GaAs substrate by molecular-beam epitaxy with different N concentrations were studied using the photoluminescence (PL) technique in the temperature range from 9 to 296 K. A strong redshift in optical transition energies induced by a small increase in N concentration has been observed in the PL spectra. This effect can be explained by the interaction between a narrow resonant band formed by the N-localized states and the conduction band of the host semiconductor. Excitonic transitions in the quantum wells show a successive red/blue/redshift with increasing temperature in the 2-100 K range. The activation energies of nonradiative channels responsible for a strong thermal quenching are deduced from an Arrhenius plot of the integrated PL intensity. (C) 2003 American Institute of Physics.

Effects of Incubation Temperature and Relative Humidity on Embryonic Development in Eggs of Red-Winged Tinamou (Rhynchotus rufescens).

This study was conducted to assess the effects of incubation temperature (34 C, 36[degree]C and 38[degree]C) and relative humidity (RH, 50% and 60%) on egg weight loss, embryo mortality, hatchability, incubation time and chick weight in eggs from red-winged tinamou. The eggs were placed in incubators that were operated at 34[degree]C, 36[degree]C, or 38[degree]C and 50% or 60% RH (mean wet bulb temperatures of 28[degree]C and 30[degree]C, respectively) from day 1 to hatching. Each treatment had two replicate groups of 30 eggs each. Hatchability varied with incubation temperature and RH and was highest for eggs incubated at 36[degree]C and 60% RH and lowest for eggs incubated at 38[degree]C. Early, intermediate and late embryo mortality were highest at 38[degree]C, 38[degree]C/50% RH, and 50% RH, respectively. Incubation period was longest at 34[degree]C and shortest at 38[degree]C/50% RH. Present results show the highest hatchability of red-winged tinamou eggs after incubation at 36[degree]C and 60% RH; highest embryo sensitivity to high temperature in the early period of incubation (1 to 7 days), to high temperature and low RH in the second period of incubation (8-14 days) and to low RH in the late period of incubation (after 15 days) and shortest incubation period with increasing temperature and RH.

Disorder-dependent photoluminescence in Ba0.8Ca0.2TiO3 at room temperature

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Changes on iron electrode surface during hydrogen permeation in borate buffer solution

Hydrogen interaction with oxide films grown on iron electrodes at open circuit potential (E-oc) and in the passive region (+0.30 V-ECS) was studied by chronopotentiometry, chronoamperometry and electrochemical impedance spectroscopy techniques. The results were obtained in deaerated 0.3 mol L-1 H3BO3 + 0.075 mol L-1 Na2B4O7 (BB, pH 8.4) solution before, during and after hydrogen permeation. The iron oxide film modification was also investigated by means of in situ X-ray absorption near-edge spectroscopy (XANES) and scanning electrochemical microscopy (SECM) before and during hydrogen permeation. The main conclusion was that the passive film is reduced during the hydrogen diffusion. The hydrogen permeation stabilizes the iron surface at a potential close to the thermodynamic water stability line where hydrogen evolution can occur. The stationary condition required for the determination of the permeation parameters cannot be easily attained on iron surface during hydrogen permeation. Moreover, additional attention must be paid when obtaining the transport parameters using the classical permeation cell. (c) 2007 Elsevier Ltd. All rights reserved.

Effect of phosphate-bonded investments on titanium reaction layer and crown fit

This study analyzed the reaction layer and measured the marginal crown fit of cast titanium applied to different phosphate-bonded investments, prepared under the following conditions (liquid concentration/casting temperature): Rema Exakt (RE) - 100%/237°C, 75%/287°C, Castorit Super C (CS)-100%/70°C, 75%/141°C and Rematitan Plus (RP)-100%/430°C (special to titanium cast, as the control group). The reaction layer was studied using the Vickers hardness test, and analyzed by two way ANOVA and Tukey's HSD tests (α = 0.05). Digital photographs were taken of the crowns seated on the die, the misfit was measured using an image analysis system and One-way ANOVA, and Tukey's test was applied (α = 0.05). The hardness decreased from the surface (601.17 VHN) to 150 μm (204.03 VHN). The group CS 75%/141°C presented higher hardness than the other groups, revealing higher surface contamination, but there were no differences among the groups at measurements deeper than 150 μm. The castings made with CS - 100%/70°C presented the lowest levels of marginal misfit, followed by RE -100%/237°C. The conventional investments CS (100%) and RE (100%) showed better marginal fit than RP, but the CS (75%) had higher surface contamination.