Parâmetros operacionais no processamento de zeólitas desativadas por fusão com KHSO4

This work presents a study on the determination of the optimal experimental conditions for processing spent commercial zeolites in order to recover lanthanide elements and eventually other elements. The process is based on the fusion of the sample with potassium hydrogenosulfate (KHSO4). Three experimental parameters were studied: temperature, reaction time and catalyst/flux mass ratio. After fusion the solid was dissolved in water and the amount of insoluble matter was used to determine the efficiency of the process. The optimized experimental parameters depend on the composition of the sample processed. Under such conditions the insoluble residue corresponds to SiO2. Lanthanide elements and aluminum present in solution were isolated by conventional precipitation techniques; the yields were at least 75 wt%. The final generated wastes correspond to neutral colorless solutions containing alkali chlorides/sulfates and solids that can be disposed of in industrial dumps.

Estabilidade da sílica biogênica extraída de capim Jaraguá (Hyparrhenia rufa) em solução de NaOH

Biogenic silica is used to describe compounds of hydrated silica (SiO2.nH2O), with specific shapes and sizes, deposited in plants. The chemical composition of biogenic silica and its stability in Jaraguá grass was studied in increasing concentration of NaOH. The analytical results demonstrated high concentration of Si, Al, Fe, Mg, P and low of Cu, Cd and Zn in the phytoliths composition. The silica bodies stability in NaOH solution with increasing concentration was different among the shapes and sizes. Silicified stomata and silicified plant tissues were dissolved along with the dumbbells because they are the less stable forms of biogenic silica.

Properties of silica from rice husk and rice husk ash and their utilization for zeolite y synthesis

This study compared properties of silica (SiO2) from rice husk (RH) and rice husk ash (RHA) extracted by acid- and heat-treatment. The SiO2 from RH was in amorphous phase with nearly 100% purity while that from RHA was in crystalline phase with 97.56% purity. Both extracted SiO2 were used in the synthesis of zeolite NaY but that from RH was better due to the efficiency in product recovery and simplicity of extraction. After the NaY was exchanged to NH4Y and calcined to convert to HY, the product did not carry over the textural properties of the parent NaY and NH4Y.

Sinterabilidade de pós de precursor vitrocerâmico do sistema LZSA tratados por troca iônica

Ion exchange method was employed by means of surface modification of the glass powders of LZSA (Li2O-ZrO2-SiO2-Al2O3) system submitted to a 70wt% NaNO3/30wt% NaSO4 bath salt followed by a heat treatment. Chemical analysis by X-ray fluorescence was used to evaluate the efficiency of ion exchange, while optical dilatometry was employed to evaluate sintering of compacts. Evaluation of the structure of sintered bodies was made by scanning electron microscopy. Substitution of Li+ ions by Na+ ions on the surface of powders during heat treatments of 450 and 600 ºC for 2-10 h promoted an increase in densification of the sintered bodies.

Impregnação do ácido 12-fosfotúngstico em sílica - parte I: determinação de parâmetros de impregnação, caracterização e avaliação da atividade catalítica

Catalyst based on Kegging-type heteropolyacids (H3PW12O40 - HPA), supported on SiO2 (H3PW), were prepared by the impregnation method under different thermal treatment conditions. The materials were characterized by different instrumental techniques and used as catalysts in the methyl esterification reactions of stearic acid. Using the catalyst with 15% of HPA, conversions higher than 60% were obtained after 2 h of reaction at 65 ºC. Recovery studies using hot-filtration with ethanol at 75 ºC showed satisfactory activity for two additional reaction cycles.

Especiação e quimissorção de Pb(II) em rejeito de caulim

This study assesses the adsorption of Pb(II) on natural kaolin waste (KRnatural) and on that treated with 3 mol L-1 H2SO4 and HCl. Equilibrium and thermodynamic parameters were determined. The results indicate that the values of CEC, specific area and SiO2/Al2O3 ratio (4.6-6.0 cmol kg-1, 14.0-16.0 m² g-1 and 1.16-1.30, respectively) vary only slightly for the adsorbents; the concentration of Pb2+ is much higher than that of other species (PbOH+ and Pb(OH)2). The values of R L, ΔGº, ΔHº and ΔSº are typical of feasible, spontaneous, exothermic and ordered adsorption. The chemisorption on KRnatural is more feasible and ordered.

REAÇÃO DE CONDENSAÇÃO DO GLICEROL COM COMPOSTOS CARBONÍLICOS. SÍNTESE, CARACTERIZAÇÃO E APLICAÇÃO EM CRISTAIS LÍQUIDOS

Condensation reactions of glycerol with aldehydes and ketones were performed under thermal heating and microwave irradiation regimes. Homogeneous and heterogeneous catalysts were tested in both conditions. A silica sulfated (SiO2-SO3H) heterogeneous catalyst demonstrated the best performance relative to a selectivity of >95% in favor of 5-membered ketals. For acetals, preference in favor of 5-membered or 6-membered functional groups depends on the nature of the catalyst. Homogenous catalysts favor the more stable 6-membered acetals, whereas heterogeneous catalysts favor the less stable 5-membered acetals. However, the isomer ratios in the acetalization reaction are too low, and hence the reaction cannot be used in a synthetic plan for functional materials. Ketalization processes mediated by SiO2-SO3H show a high selectivity in favor of a 5-membered ring (1,3-dioxolane). The scope of condensation was tested with different ketones. A mechanism for heterogeneous catalysis related to the selectivity in the cyclization process is presented herein. Solketal, a commercial product, was also obtained by a condensation reaction of glycerol and propanone, and showed a high selectivity in favor of 1,3-dioxolane. It was transformed to potential allylic and chiral intermediates. A mesogenic core was connected to the organic framework of glycerol to produce a monomer liquid crystal material with a stable smectic-C mesophase.

Intensidade da cercosporiose em mudas de cafeeiro em função de fontes e doses de silício

O objetivo deste estudo foi avaliar o efeito dos silicatos de cálcio e de sódio sobre a intensidade da cercosporiose (Cercospora coffeicola) em mudas de cafeeiro (Coffea arabica), cultivar Catuaí IAC 99, nas doses 0; 0,32; 0,64; 1,26 g de SiO2.kg-1 de substrato. Foram realizadas cinco avaliações quinzenais nas quais se quantificou o número de plantas doentes, o número de folhas lesionadas por planta, o número de lesões por folha e o número total de lesões por planta. Essas avaliações foram utilizadas para construir a área abaixo da curva de progresso da doença. Ao término das avaliações, foram determinados os teores de macro, micronutrientes, silício e lignina na parte aérea das mudas de cafeeiro. A menor área abaixo da curva de progresso do total de lesões foi obtida com a dose de 0,84 g.kg-1 de silicato de sódio. Observou-se decréscimo linear para área abaixo da curva de progresso do número de plantas doentes e aumento na concentração de lignina nas folhas até a dose de 0,52 g.kg-1 de silicato de sódio, enquanto no caule houve acúmulo de SiO2 até 0,53 g.kg.-1.

Redução de crômio hexavalente por substâncias húmicas aquáticas imobilizadas em aminopropil sílica

Estudou-se a redução de Cr(VI) à Cr(III) utilizando-se um novo suporte preparado pela ativação de aminopropil sílica com substâncias húmicas aquáticas (ATPS-SiO2-SHA). Coletaram-se amostras de água no Corrégo Itapitangui localizado no município de Cananéia-SP e extraíram-se as SHA utilizando-se procedimento recomendado pela Sociedade Internacional de Substâncias Húmicas. Após purificação por diálise, fez-se a imobilização das SHA na aminopropil sílica (APTS-SiO2) em pH 7,0, sob agitação mecânica por 48 horas à temperatura ambiente. Adicionaram-se 150 mg de APTS-SiO2-SHA à 150 mL de soluções 9,5 mimol L-1 de Cr(VI), fixou-se o pH em 2,5, 4,5 e 6,0 e mantiveram-se as misturas sob agitação mecânica à temperatura ambiente. Coletaram-se alíquotas em função do tempo (0-72 horas) e as concentrações de Cr(VI) foram determinadas por espectrofotometria baseada na reação com 1,5-difenilcarbazida. A porcentagem de redução de Cr(VI) por APTS-SiO2-SHA foi de 50, 4 e 0 % em pH 2,5, 4,5 e 6,0, respectivamente. Dobrando a massa do suporte APTS-SiO2-SHA verificou-se em pH 2,5, a redução de 70 % de Cr(VI). Esses resultados preliminares mostram forte influência do pH e da quantidade de APTS-SiO2-SHA no processo de redução do Cr(VI). Após outros estudos, a utilização do suporte APTS-SiO2-SHA pode ser uma alternativa viável a ser aplicada para o tratamento de resíduos e/ou estudos de especiação de crômio.

Adsorption of hidrogen peroxide on the surface of silica - titania mixed oxide obtained by the sol-gel processing method

This work describes the sol-gel mixed oxide SiO2/TiO2 property, ST, as prepared, and submitted to heat treatment a 773 K, STC. SEM and EDS images show, within magnification used, a uniform distribution of the TiO2 particles in SiO2/TiO2 matrix. Both, ST and STC adsorb hydrogen peroxide on the surface and through EPR and UV-Vis diffuse reflectance spectra, it was possible to conclude that the species on the surface is the peroxide molecule attached to the Lewis acid site of titanium particle surface, alphaTi(H2O2)+. As the material is very porous, presumably the hydrogen peroxide molecule is confined in the matrix pores on the surface, a reason why the adsorbed species presents an exceptional long lived stability.

Eletrodo de pasta de carbono em minicavidade de contato sólido

Este trabalho descreve a preparação de eletrodo de pasta de carbono (EPC) em minicavidade de contato sólido e sua avaliação quando a pasta de carbono contém ou não partículas sub-micormétricas de SiO2(Eu3+ 2%) e SiO2(Eu3+ 2%)-lisina. Nestes estudos, medidas de voltametria cíclica e impedância eletroquímica foram realizadas em PBS (0,1 mol L-1 pH 7,4) contendo as espécies redox Fe(CN)6-3/-4. Os resultados de impedância foram interpretados baseados na reação de transferência de carga envolvendo as espécies Fe(CN)6-3/-4 e/ou oxigênio em frequências mais altas e, difusão das espécies eletroativas e características da pasta de carbono a baixas frequências. EPC-minicavidade é apropriado para eletroanálises usando pasta de carbono modificada.

Recovery and refining of manganese as by-product from hydrometallurgical processes

The consumption of manganese is increasing, but huge amounts of manganese still end up in waste in hydrometallurgical processes. The recovery of manganese from multi-metal solutions at low concentrations may not be economical. In addition, poor iron control typically prevents the production of high purity manganese. Separation of iron from manganese can be done with chemical precipitation or solvent extraction methods. Combined carbonate precipitation with air oxidation is a feasible method to separate iron and manganese due to the fast kinetics, good controllability and economical reagents. In addition the leaching of manganese carbonate is easier and less acid consuming than that of hydroxide or sulfide precipitates. Selective iron removal with great efficiency from MnSO4 solution is achieved by combined oxygen or air oxidation and CaCO3 precipitation at pH > 5.8 and at a redox potential of > 200 mV. In order to avoid gypsum formation, soda ash should be used instead of limestone. In such case, however, extra attention needs to be paid on the reagents mole ratios in order to avoid manganese coprecipitation. After iron removal, pure MnSO4 solution was obtained by solvent extraction using organophosphorus reagents, di-(2-ethylhexyl)phosphoric acid (D2EHPA) and bis(2,4,4- trimethylpentyl)phosphinic acid (CYANEX 272). The Mn/Ca and Mn/Mg selectivities can be increased by decreasing the temperature from the commonly used temperatures (40 –60oC) to 5oC. The extraction order of D2EHPA (Ca before Mn) at low temperature remains unchanged but the lowering of temperature causes an increase in viscosity and slower phase separation. Of these regents, CYANEX 272 is selective for Mn over Ca and, therefore, it would be the better choice if there is Ca present in solution. A three-stage Mn extraction followed by a two-stage scrubbing and two-stage sulfuric acid stripping is an effective method of producing a very pure MnSO4 intermediate solution for further processing. From the intermediate MnSO4 some special Mn- products for ion exchange applications were synthesized and studied. Three types of octahedrally coordinated manganese oxide materials as an alternative final product for manganese were chosen for synthesis: layer structured Nabirnessite, tunnel structured Mg-todorokite and K-kryptomelane. As an alternative source of pure MnSO4 intermediate, kryptomelane was synthesized by using a synthetic hydrometallurgical tailings. The results show that the studied OMS materials adsorb selectively Cu, Ni, Cd and K in the presence of Ca and Mg. It was also found that the exchange rates were reasonably high due to the small particle dimensions. Materials are stable in the studied conditions and their maximum Cu uptake capacity was 1.3 mmol/g. Competitive uptake of metals and acid was studied using equilibrium, batch kinetic and fixed-bed measurements. The experimental data was correlated with a dynamic model, which also accounts for the dissolution of the framework manganese. Manganese oxide micro-crystals were also bound onto silica to prepare a composite material having a particle size large enough to be used in column separation experiments. The MnOx/SiO2 ratio was found to affect significantly the properties of the composite. The higher the ratio, the lower is the specific surface area, the pore volume and the pore size. On the other hand, higher amount of silica binder gives composites better mechanical properties. Birnesite and todorokite can be aggregated successfully with colloidal silica at pH 4 and with MnO2/SiO2 weight ratio of 0.7. The best gelation and drying temperature was 110oC and sufficiently strong composites were obtained by additional heat-treatment at 250oC for 2 h. The results show that silica–supported MnO2 materials can be utilized to separate copper from nickel and cadmium. The behavior of the composites can be explained reasonably well with the presented model and the parameters estimated from the data of the unsupported oxides. The metal uptake capacities of the prepared materials were quite small. For example, the final copper loading was 0.14 mmol/gMnO2. According to the results the special MnO2 materials are potential for a specific environmental application to uptake harmful metal ions.

Features of a Ziegler-Natta catalyst prepared with the Sirius emulsion-based catalyst production technology

Traditionellt har man ansett att Ziegler-Natta katalysatorer för framställning av polypropen bör ha stor inre yta och hög porositet för att ge hög aktivitet och bra polymerpartikelmorfologi. Den av Borealis utvecklade Sirius emulsionsbaserade katalysatortillverkningsteknologin ger katalysatorer utan mätbar inre yta och porositet. Katalysatorn ger, trots sin kompakthet, polymerpartiklar med utmärkt morfologi och har hög aktivitet. Sirius katalysatorns prestanda, beträffande polymerisationskinetik och polymerstruktur, undersöktes i detta doktorsarbete. En jämn och kontrollerad tidig fragmentering av katalysatorn är av största vikt för att uppnå bra partikelmorfologi i en kommersiell process. Det visades att fragmenteringen av Sirius katalysatorn under de första sekunderna och minuterna av reaktionen framskred på ett homogent sätt. Oligomerhalten i den slutliga produkten är viktig i många applikationer, tex. i applikationer där polymeren kommer i kontakt med mat. Polymerer producerade med Sirius katalysatorn hade en låg oligomerhalt på grund av den smala molekylviktsfördelningen. Analys av kedjeändorna avslöjade att Sirius katalysatorn hade en hög frekvens av kedjeöverföring till monomer, vilket förklarade Sirius katalysatorns något begränsade förmåga att producera polymerer med hög molekylvikt. Sampolymerer av propen och eten producerade med Sirius uppvisade jämnare eten fördelning mellan långa och korta kedjor samt en mera randomiserad fördelning av eten längs med kedjorna än med den konventionella referenskatalysatorn. Tillsammans med den smala molekylviktsfördelningen indikerade resultaten att fördelningen av typer av aktiva centrum i Sirius katalysatorn är smal. Då man producerar polypropen med hög slagseghet skall polymerpartiklarna ha hög porositet för att kunna ackumulera eten/propen gummit. SiO2 nanopartiklar tillsatta under framställningen av Sirius katalysatorn ökade polymerpartikelns porositet, vilket möjliggjorde en dramatisk ökning av gummihalten.

Physico-chemical characterization of nanoparticle coated paper

Förståelse av olika ytors vätningsegenskaper är viktig i många pappers-relaterade industriella processer eftersom vätningen påverkar materialbeteendet, t.ex. vid bestrykning, tryckning och laminering. Förmågan att kontrollera vätningen är av intresse, därför att den ger nya möjligheter till modifikation av ytor. Vätningen styrs av ytans struktur och kemi. Kunskap om dessa egenskaper krävs både i fundamentala studier och för industriella applikationer. Nanopartiklar används ofta för att skapa funktionella ytor med mångsidiga egenskaper. Detta arbete strävar till att förstå de fysikalisk-kemiska egenskaperna hos papper och kartong som är bestrukna med nanopartiklar, för att sedan kunna förklara de observerade förändringarna i ytornas vätningsförmåga. Funktionella ytor med justerbar vätningsförmåga tillverkades genom att deponera nanopartiklar i en rulle-till-rulle vätskeflammasprutningprocess (LFS). TiO2 -nanopartikelbeläggningen skapar en superhydrofob yta som har över 160° kontaktvinkelmed vatten, medan SiO2-nanopartikelbeläggningar skapar mycket hydrofila ytor med kontaktvinklar så låga som 21° med vatten. Superhydrofobiciteten eller hydrofiliteten är ett resultat av den kombinerade effekten hos ytstrukturen och ytkemin, såsom nanopartiklarnas oxidationsnivå eller karbonatiseringsnivå. Kartongytor som är bestrukna med TiO2-nanopartiklar kan vara såväl superhydrofoba som hydrofila. Hydrofilitet kan induceras genom UVA-strålning, medan behandling i hög temperatur i ugn resulterar i en superhydrofob yta. Ett mål med arbetet var att förstå mekanismerna hos de kemiska för ändringar som sker under UVA-bestrålning och värmebehandling av ytor, bestrukna med TiO2-nanopartiklar. Ytornas abrasions- och kompressionsmotstånd samt relaterade förändringar i funktionella egenskaper undersöktes. Resultaten skapar en bättre förståelse för potentiell användning av LFS-nanopartikelbeläggningar i pappersrelaterade applikationer. En förståelse för stabiliteten hos nanopartikelbeläggningarna när de exponeras för externa krafter är viktig för att försäkra deras funktionalitet i industriella applikationer och för att garantera beläggningarnas miljö-, hälso- och säkerhetsaspekter. ------------------------------------------ Pinnan kastumisominaisuuksien hallinta on tärkeää monissa paperiteollisuuden prosesseissa, sillä pinnan kastuminen vaikuttaa esimerkiksi päällystämiseen, painamiseen ja laminointiin. Pinnan kastuvuuden säätäminen avaa mielenkiintoisia uusia mahdollisuuksia pintojen ominaisuuksien hallintaan. Pinnan kastuvuus määräytyy pinnan rakenteesta ja kemiasta, ja näiden ominaisuuksien ymmärtäminen on tärkeää sekä perustutkimuksessa että teollisissa sovelluksissa. Nanopartikkeleita käytetään usein toiminnallisten ja hallitusti kastuvien pintojen aikaansaamiseksi. Tässä työssä on tarkasteltu nanopartikkelipinnoitetun paperin ja kartongin fysikaalis-kemiallisia pintaominaisuuksia, jotka selittävät havaittuja muutoksia pinnan kastuvuudessa. Toiminnalliset pinnat säädettävillä kastuvuusominaisuuksilla valmistettiin nesteliekkiruiskutus (LFS) nanopartikkelipinnoituksella rullalta rullalle-menetelmällä. TiO2-nanopartikkelipäällystys saa aikaan superhydrofobisen pinnan, jonka veden kontaktikulma on suurempi kuin 160°. Toisaalta SiO2-nanopartikkelipäällystys muuttaa pinnan hyvin hydrofiiliseksi, veden kontaktikulman ollessa vain 21°. Pinnan superhydrofobisuus tai hydrofiilisyys riippuu nanopartikkelipinnan rakenteesta ja pintakemiasta kuten pinnan hapettumisasteesta ja hiilipitoisuudesta. TiO2-nanopartikkelipinnoitetun kartonkipinnan kastumista voidaan säätää superhydrofobisen ja hydrofiilisen välillä. Pinnan hydrofiilisyys saadaan aikaan UVA-valolla, kun taas superhydrofobinen pinta voidaan palauttaa korkeassa lämpötilassa uunissa. Tämän työn tavoitteena oli selvittää, millaisia muutoksia TiO2-nanopartikkelipäällystetyn pinnan kemiassa tapahtuu UVA-valon ja lämpökäsittelyn vaikutuksesta. Työssä tarkasteltiin myös pinnan mekaanisen hankauksen ja kokoonpuristuksen vaikutusta toiminnallisiin ominaisuuksiin. Työssä saavutetut tulokset auttavat ymmärtämään LFS-nanopartikkelipäällystettyjen pintojen soveltuvuutta paperiin liittyvissä sovelluksissa. Nanopartikkelipäällystettyjen pintojen stabiilius ulkoisten voimien alaisena on tärkeää toiminnallisten päällystysten ympäristö-, terveys- ja turvallisuusnäkökulmia tarkasteltaessa.

IR - spectroscopic characterization of biominerals in marattiaceaeus ferns

(IR - spectroscopic characterization of biominerals in marattiaceaeus ferns). Frond samples of the eusporangiate ferns Marattiaceae genera Angiopteris, Christensenia, Danaea and Marattia were investigated by infrared spectroscopy, under different experimental conditions. The results confirmed the previously reported accumulation of biogenic silica (SiO2) in tissues of these ferns and also showed, for the first time, the presence of calcium oxalate in this group of plants, probably as weddellite. The ability to biomineralize SiO2, to produce and accumulate biogenic silica, is suggested now to be a general family trait of the Marattiaceae.