Discrete element modelling of the influence of lifters on power draw of tumbling mills

Crushing and grinding are the most energy intensive part of the mineral recovery process. A major part of rock size reduction occurs in tumbling mills. Empirical models for the power draw of tumbling mills do not consider the effect of lifters. Discrete element modelling was used to investigate the effect of lifter condition on the power draw of tumbling mill. Results obtained with PFC3D code show that lifter condition will have a significant influence on the power draw and on the mode of energy consumption in the mill. Relatively high lifters will consume less power than low lifters, under otherwise identical conditions. The fraction of the power that will be consumed as friction will increase as the height of the lifters decreases. This will result in less power being used for high intensity comminution caused by the impacts. The fraction of the power that will be used to overcome frictional resistance is determined by the material's coefficient of friction. Based on the modelled results, it appears that the effective coefficient of friction for in situ mill is close to 0.1. (C) 2003 Elsevier Science Ltd. All rights reserved.

Applying discrete element modelling to vertical and horizontal shaft impact crushers

The PFC3D (particle flow code) that models the movement and interaction of particles by the DEM techniques was employed to simulate the particle movement and to calculate the velocity and energy distribution of collision in two types of impact crusher: the Canica vertical shaft crusher and the BJD horizontal shaft swing hammer mill. The distribution of collision energies was then converted into a product size distribution for a particular ore type using JKMRC impact breakage test data. Experimental data of the Canica VSI crusher treating quarry and the BJD hammer mill treating coal were used to verify the DEM simulation results. Upon the DEM procedures being validated, a detailed simulation study was conducted to investigate the effects of the machine design and operational conditions on velocity and energy distributions of collision inside the milling chamber and on the particle breakage behaviour. (C) 2003 Elsevier Ltd. All rights reserved.

Modelling the size of the crushed zone around a blasthole

A new model to predict the extent of crushing around a blasthole is presented. The model is based on the back-analysis of a comprehensive experimental program that included the direct measurement of the zone of crushing from 92 blasting tests on concrete blocks using two commercial explosives. The concrete blocks varied from low, medium to high strength and measured 1.5 in in length, 1.0 m in width and 1.1 m in height. A dimensionless parameter called the crushing zone index (CZI) is introduced. This index measures the crushing potential of a charged blasthole and is a function of the borehole pressure, the unconfined compressive strength of the rock material, dynamic Young's modulus and Poisson's ratio. It is shown that the radius of crushing is a function of the CZI and the blasthole radius. A good correlation between the new model and measured results was obtained. A number of previously proposed models could not approximate the conditions measured in the experimental work and there are noted discrepancies between the different approaches reviewed, particularly for smaller diameter holes and low strength rock conditions. The new model has been verified with full scale tests reported in the literature. Results from this validation and model evaluations show its applicability to production blasting. (C) 2003 Elsevier Science Ltd. All rights reserved.

Discrete element modelling of power draw of tumbling mills

The power required to operate large mills is typically 5-10 MW. Hence, optimisation of power consumption will have a significant impact on overall economic performance and environmental impact. Power draw modelling results using the discrete element code PFC3D have been compared with results derived from the widely used empirical Model of Morrell. This is achieved by calculating the power draw for a range of operating conditions for constant mill size and fill factor using two modelling approaches. fThe discrete element modelling results show that, apart from density, selection of the appropriate material damping ratio is critical for the accuracy of modelling of the mill power draw. The relative insensitivity of the power draw to the material stiffness allows selection of moderate stiffness values, which result in acceptable computation time. The results obtained confirm that modelling of the power draw for a vertical slice of the mill, of thickness 20% of the mill length, is a reliable substitute for modelling the full mill. The power draw predictions from PFC3D show good agreement with those obtained using the empirical model. Due to its inherent flexibility, power draw modelling using PFC3D appears to be a viable and attractive alternative to empirical models where necessary code and computer power are available.

The use of 16s rDNA restriction fragment length polymorphism analysis for the identification of non-fermenting gram negative bacilli in a cystic fibrosis microbiology referral service

The utility of 16s rDNA restriction fragment length polymorphism (RFLP) analysis for the partial genomovar differentiation of Burkholderia cepacia complex bacterium is well documented. We compared the 16s rDNA RFLP signatures for a number of non-fermenting gram negative bacilli (NF GNB) LMG control strains and clinical isolates pertaining to the genera Burkholderia, Pseudomonas, Achromobacter (Alcaligenes), Ralstonia, Stenotrophomonas and Pandoraea. A collection of 24 control strain (LMG) and 25 clinical isolates were included in the study. Using conventional PCR, a 1.2 kbp 16s rDNA fragment was generated for each organism. Following restriction digestion and electrophoresis, each clinical isolate RFLP signature was compared to those of the control strain panel. Nineteen different RFLP signatures were detected from the 28 control strains included in the study. TwentyoneyTwenty- five of the clinical isolates could be classified by RFLP analysis into a single genus and species when compared to the patterns produced by the control strain panel. Four clinical B. pseudomallei isolates produced RFLP signatures which were indistinguishable from B. cepacia genomovars I, III and VIII. The identity of these four isolates were confirmed using B. pseudomallei specific PCR. 16s rDNA RFLP analysis can be a useful identification strategy when applied to NF GNB, particularly for those which exhibit colistin sulfate resistance. The use of this molecular based methodology has proved very useful in the setting of a CF referral laboratory particularly when utilised in conjunction with B. cepacia complex and genomovar specific PCR techniques. Species specific PCR or sequence analysis should be considered for selected isolates; especially where discrepancies between epidemiology, phenotypic and genotypic characteristics occur.

The effectiveness of personalized smoking cessation strategies for callers to a Quitline service

Aim To assess the effectiveness of a program of computer-generated tailored advice for callers to a telephone helpline, and to assess whether it enhanced a series of callback telephone counselling sessions in aiding smoking cessation. Design Randomized controlled trial comparing: (1) untailored self-help materials; (2) computer-generated tailored advice only, and (3) computer-generated tailored advice plus callback telephone counselling. Assessment surveys were conducted at baseline, 3, 6 and 12 months. Setting Victoria, Australia. Participants A total of 1578 smokers who called the Quitline service and agreed to participate. Measurements Smoking status at follow-up; duration of cessation, if quit; use of nicotine replacement therapy; and extent of participation in the callback service. Findings At the 3-month follow-up, significantly more (chi(2)(2) = 16.9; P < 0.001) participants in the computer-generated tailored advice plus telephone counselling condition were not smoking (21%) than in either the computer-generated advice only (12%) or the control condition (12%). Proportions reporting not smoking at the 12-month follow-up were 26%, 23% and 22%, respectively (NS) for point prevalence, and for 9 months sustained abstinence; 8.2, 6.0, and 5.0 (NS). In the telephone counselling group, those receiving callbacks were more likely than those who did not to have sustained abstinence at 12 months (10.2 compared with 4.0, P < 0.05). Logistic regression on 3-month data showed significant independent effects on cessation of telephone counselling and use of NRT, but not of computer-generated tailored advice. Conclusion Computer-generated tailored advice did not enhance telephone counselling, nor have any independent effect on cessation. This may be due to poor timing of the computer-generated tailored advice and poor integration of the two modes of advice.

O Senior Executive Service: especial refer??ncia ao perfil do Top Public Service em Portugal

No contexto de reforma da administra????o p??blica, o objectivo do trabalho pretende dar conta das caracter??sticas dos modelos de direc????o p??blica, em particular dos dirigentes (Senior Executive Service: Top Public Service e Top Management Service), e do seu perfil em face dos novos desafios da administra????o p??blica. O objectivo principal deste trabalho foi caracterizar o sistema de designa????o/ nomea????o para os cargos de dirigente de livre escolha pol??tica, sistema conhecido na literatura como spoil system, com especial refer??ncia ao 1o e 2o n??veis, grupo I, dessas fun????es, no contexto da elite das direc????es-gerais em Portugal.

Modelling the Mechanical Behavior of Polymer-Based Nanocomposites

Molecular dynamics simulations were employed to analyze the mechanical properties of polymer-based nanocomposites with varying nanofiber network parameters. The study was focused on nanofiber aspect ratio, concentration and initial orientation. The reinforcing phase affects the behavior of the polymeric nanocomposite. Simulations have shown that the fiber concentration has a significant effect on the properties, with higher loadings resulting in higher stress levels and higher stiffness, matching the general behavior from experimental knowledge in this field. The results also indicate that, within the studied range, the observed effect of the aspect ratio and initial orientation is smaller than that of the concentration, and that these two parameters are interrelated.

O senior executive service (SES): especial referência ao perfil do top public service (TPS) em Portugal

Alguns dos países da OCDE (2002) enfrentam, hoje, problemas relacionados ao emprego público e à sua competitividade (recrutamento, retenção de pessoal, falta crítica de habilidades e competências, etc.). Em nível de recrutamento (OCDE, 2002), os países que já identificaram o problema são o Canadá, a Dinamarca e a Finlândia; a falta crítica de habilidades e de competências foi já identificada por: Itália, Coreia, Noruega, Polónia, Portugal1 , Espanha, Áustria e Alemanha. O desenho e a implementação de estratégias de recursos humanos nas organizações públicas desenrolam-se em ambiente altamente politizado (LACOVIELLO, 1996) e o processo de decisão está sujeito a influências que tomam proporções maiores pelas características particulares que apresentam e pelo conflito essencial que decorre das relações entre políticos e burocratas.

Broad and restricted scope of the concept of civil service: a multipolarização do conceito de publica nos modelos hibricos. A capacidade transformadora dos memorados de entendimento: Portugal e Irlanda

Analise do conceito de Função Publica, identificando, á partida, uma dicotomia conceptual, entre um modelo marcadamente continental(broad concept of civil service) e um modelo restrito(restricted scope of the concept of civil service), característico dos países anglo-saxónicos, aflorando a reforma da Administração Publica, na senda da New Public Management, como o caminho para a afirmação de modelos híbridos, com características de laboralização da Função Publica e de flexisegurança, que surgem como consequência da pulverização daquela dicotomia, revelando uma miscigenação entre os modelos iniciais e elementos externos, de acordo com as idiossincrasias de cada país. Posterior estudo de caso, versando sobre Portugal e a Irlanda , dois países que, são contrario do que a tradição anglo- saxónica da Irlanda faria adivinhar, partilham um conceito amplo de Função Publica(broad concept of Civil Service), apoiado num sistema de carreira(carrear sytem). Percorrerem, quase em simultâneo, o caminho de um regate económico-financeiro desenvolvido pelo Fundo Monetário Internacional, Banco Central Europeu e Comissão Europeia. Procurara investiga-se se o acordo firmado entre os dois países e a Troika, materializado nos respectivos Memorando de Entendimento e sucessivas revisões, no período compreendido entre 16 de Dezembro de 2010 e 31 de Dezembro de 2012, introduziu modificações nos respectivos modelos de Função Publica, designadamente forçando-os a uma aproximação do restricted scope of the concept of Civil Service e, com isso, projectando-os para a adopção de modelos híbridos.

Predicting the mechanical behavior of amorphous polymeric materials under strain through multi-scale simulation

Polymeric materials have become the reference material for high reliability and performance applications. However, their performance in service conditions is difficult to predict, due in large part to their inherent complex morphology, which leads to non-linear and anisotropic behavior, highly dependent on the thermomechanical environment under which it is processed. In this work, a multiscale approach is proposed to investigate the mechanical properties of polymeric-based material under strain. To achieve a better understanding of phenomena occurring at the smaller scales, the coupling of a finite element method (FEM) and molecular dynamics (MD) modeling, in an iterative procedure, was employed, enabling the prediction of the macroscopic constitutive response. As the mechanical response can be related to the local microstructure, which in turn depends on the nano-scale structure, this multiscale approach computes the stress-strain relationship at every analysis point of the macro-structure by detailed modeling of the underlying micro- and meso-scale deformation phenomena. The proposed multiscale approach can enable prediction of properties at the macroscale while taking into consideration phenomena that occur at the mesoscale, thus offering an increased potential accuracy compared to traditional methods.

Artificial neural networks for automatic modelling of the pectus excavatum corrective prosthesis

Pectus excavatum is the most common deformity of the thorax and usually comprises Computed Tomography (CT) examination for pre-operative diagnosis. Aiming at the elimination of the high amounts of CT radiation exposure, this work presents a new methodology for the replacement of CT by a laser scanner (radiation-free) in the treatment of pectus excavatum using personally modeled prosthesis. The complete elimination of CT involves the determination of ribs external outline, at the maximum sternum depression point for prosthesis placement, based on chest wall skin surface information, acquired by a laser scanner. The developed solution resorts to artificial neural networks trained with data vectors from 165 patients. Scaled Conjugate Gradient, Levenberg-Marquardt, Resilient Back propagation and One Step Secant gradient learning algorithms were used. The training procedure was performed using the soft tissue thicknesses, determined using image processing techniques that automatically segment the skin and rib cage. The developed solution was then used to determine the ribs outline in data from 20 patient scanners. Tests revealed that ribs position can be estimated with an average error of about 6.82±5.7 mm for the left and right side of the patient. Such an error range is well below current prosthesis manual modeling (11.7±4.01 mm) even without CT imagiology, indicating a considerable step forward towards CT replacement by a 3D scanner for prosthesis personalization.