Production of biodiesel from babassu oil using methanol-ethanol blends

Maranhão state in Brazil presents a big potential for the cultivation of several oleaginous species, such as babassu, soybean, castor oil plant, etc... These vegetable oils can be transformed into biodiesel by the transesterification reaction in an alkaline medium, using methanol or ethanol. The biodiesel production from a blend of these alcohols is a way of adding the technical and economical advantages of methanol to the environmental advantages of ethanol. The optimized alcohol blend was observed to be a methanol/ethanol volume ratio of 80 % MeOH: 20 % EtOH. The ester content was of 98.70 %, a value higher than the target of the ANP, 96.5 % (m/m), and the biodiesel mass yield was of 95.32 %. This biodiesel fulfills the specifications of moisture, specific gravity, kinematic viscosity and percentages of free alcohols (methanol plus ethanol) and free glycerin.

Adsorption isotherm studies of BOD, TSS and colour reduction from palm oil mill effluent (POME) using boiler fly ash

Palm oil is one of the two most important vegetable oils in the world's oil and fats market. The extraction and purification processes generate different kinds of waste generally known as palm oil mill effluent (POME). Earlier studies had indicated the possibility of using boiler fly ash to adsorb impurities and colour in POME treatment. The adsorption treatment of POME using boiler fly ash was further investigated in detail in this work with regards to the reduction of BOD, colour and TSS from palm oil mill effluent. The amount of BOD, colour and TSS adsorbed increased as the weight of the boiler fly ash used was increased. Also, the smaller particle size of 425µm adsorbed more than the 850µm size. Attempts were made to fit the experimental data with the Freundlich, Langmuir and Dubinin-Radushkevich isotherms. The R² values, which ranged from 0.8974-0.9898, 0.8848-0.9824 and 0.6235-0.9101 for Freundlich, Langmuir and Dubinin-Radushkevich isotherms respectively, showed that Freundlich isotherm gave a better fit followed by Langmuir and then Dubinin-Radushkevich isotherm. The sorption trend could be put as BOD > Colour > TSS. The apparent energy of adsorption was found to be 1.25, 0.58 and 0.97 (KJ/mol) for BOD, colour and TSS respectively, showing that sorption process occurs by physiosorption. Therefore, boiler fly ash is capable of reducing BOD, Colour and TSS from POME and hence could be used to develop a good adsorbent for POME treatment.

The health effects of sea buckthorn berries and oil

Sea buckthorn (Hippophaë) berries are ingredients of the Chinese traditional medicine. In addition to China, they are nowadays cultivated for food in several European countries, Russia, Canada, the USA, and Japan. Sea buckthorn berries are a rich source of flavonoids, mainly flavonol glycosides and proanthocyanidins. Depending on the genetic background, growth conditions, and ripeness of the berries, vitamin C concentrations up to over 1 g/100 ml juice, have been reported. Sea buckthorn berries contain inositols and methyl inositols, components of messenger molecules in humans. Sea buckthorn seed oil is rich in essential aplha-linolenic and linoleic acids, whereas the most abundant fatty acids in the berry oil are palmitoleic, palmitic and oleic acids. Other potentially beneficial lipophilic compounds of sea buckthorn seeds and berries include carotenoids, phytosterols, tocopherols and tocotrienols. The effects of sea buckthorn fractions on inflammation, platelet aggregation, oxidation injuries, the liver, skin and mucosa, among others, have been reported. The aim of the thesis work was to investigate the health effects of sea buckthorn berries and oil in humans. The physiological effects of sea buckthorn berries, berry components, and oil have mostly been studied in vitro and in animal models, leaving a demand for more clinical trials. In the first randomized, placebo-controlled trial of this thesis healthy adults consumed 28 g/day of sea buckthorn berries for three months. The main objective was to investigate the effects on the common cold. In addition, effects on other infections, inflammation and circulating lipid markers associated with cardiovascular disease risk were studied. In the second randomized, placebocontrolled trial participants reporting dry eye symptoms consumed 2 g/day of sea buckthorn oil from the seeds and berries for three months. The effects on symptoms and clinical signs of dry eye were monitored. In addition, the effects on circulating markers of inflammation and liver functions were analyzed. Sea buckthorn berries did not affect the common cold or other infections in healthy adults. However, a decrease in serum C-reactive protein was detected, indicating effects on inflammation. Fasting concentrations of serum flavonols, typical to sea buckthorn berry, increased without affecting the circulating total, HDL, LDL cholesterol, or triacylglycerol concentrations. Tear film hyperosmolarity and activation of inflammation at the ocular surface are among the core mechanisms of dry eye. Combined sea buckthorn berry and seed oil attenuated the rise in tear film osmolarity taking place during the cold season. It also positively affected some of the dry eye symptoms. Based on the tear film fatty acid analysis, the effects were not mediated through direct incorporation of sea buckthorn oil fatty acids to tear film lipids. It is likely that the fatty acids, carotenoids, tocopherols and tocotrienols of sea buckthorn oil affected the inflammation of the ocular surface, lacrimal and/or meibomian glands. The effects on the differentiation of meibomian gland cells are also possible. Sea buckthorn oil did not affect the serum concentrations of inflammation markers or liver enzymes investigated. In conclusion, this thesis work suggests positive effects of sea buckthorn berries and oil on inflammation and dry eye, respectively, in humans.

Advanced orbital pipe welding

Since the introduction of automatic orbital welding in pipeline application in 1961, significant improvements have been obtained in orbital pipe welding systems. Requirement of more productive welding systems for pipeline application forces manufacturers to innovate new advanced systems and welding processes for orbital welding method. Various methods have been used to make welding process adaptive, such as visual sensing, passive visual sensing, real-time intelligent control, scan welding technique, multi laser vision sensor, thermal scanning, adaptive image processing, neural network model, machine vision, and optical sensing. Numerous studies are reviewed and discussed in this Master’s thesis and based on a wide range of experiments which already have been accomplished by different researches the vision sensor are reported to be the best choice for adaptive orbital pipe welding system. Also, in this study the most welding processes as well as the most pipe variations welded by orbital welding systems mainly for oil and gas pipeline applications are explained. The welding results show that Gas Metal Arc Welding (GMAW) and its variants like Surface Tension Transfer (STT) and modified short circuit are the most preferred processes in the welding of root pass and can be replaced to the Gas Tungsten Arc Welding (GTAW) in many applications. Furthermore, dual-tandem gas metal arc welding technique is currently considered the most efficient method in the welding of fill pass. Orbital GTAW process mostly is applied for applications ranging from single run welding of thin walled stainless tubes to multi run welding of thick walled pipes. Flux cored arc welding process is faster process with higher deposition rate and recently this process is getting more popular in pipe welding applications. Also, combination of gas metal arc welding and Nd:YAG laser has shown acceptable results in girth welding of land pipelines for oil and gas industry. This Master’s thesis can be implemented as a guideline in welding of pipes and tubes to achieve higher quality and efficiency. Also, this research can be used as a base material for future investigations to supplement present finding.

Economics of combined power plant and pyrolysis bio-oil production

There are reasons of necessity in bio-fuel use and bio-energy fast development. It includes the material about bio-energy technologies, applications and methods. There are basic thermodynamics and economic theories. The economic calculation presents the comparison between two combinations. There are boiler plant below 20 MW in combination with ablative pyrolysis plant for bio-oil production and CHP plant below 100 MW in combination with the RTP pyrolysis bio-oil production technology. It provides a material about wood chips and bio-oil characteristics and explains it nature, presents the situation around the bio-fuel market or bio-fuel trade. There is a description of pyrolysis technologies such as ablative and RTP. The liquid product of the pyrolysis processes is bio-oil. The bio-oil could be different even of the same production process, because of the raw material nature and characteristics. The calculation shows advantages and weaknesses of combinations and obtained a proof of suppositions. The next thing, proven by this work is the fact that to get more efficiency from energy project it is good possibility to built plants in combinations.

Alkylointiyksikön neutralointi- ja puhdistusprosessin kehittäminen

Tämä diplomityö käsittelee Neste Oilin Porvoon jalostamon HF-alkylointiyksikön alasajon ja huoltopysäytyksen rajapintaa. Työssä tarkastellaan erilaisia vaihtoehtoja alasajon aikaisen neutralointi- ja puhdistusprosessin kehittämiseen huomioiden materiaalitekninen näkökulma. Työn alkuosassa esitellään alkyloinnin perusperiaate, huoltopysäytysprosessi sekä eri neutralointi- ja puhdistusprosessit, joista tarkemmin nykyisin jalostamolla käytettävä EnvTech:n prosessi. Työssä on myös kerrottu alkyloinnin erityisvaatimukset materiaaleille, joista tarkemmin on esitelty perusmateriaaleina käytettävät hiiliteräs A106 sekä Monel® 400. Näiden perusmateriaalien kohdalla on myös esitelty kirjallisuuden pohjalta niiden käyttäytyminen fluorivety-ympäristössä. Työn loppuosassa on esitelty eri vaihtoehtoja, jotta käyttövarmuutta voitaisiin kehittää yhdessä mahdollisesti kasvavien tuotantomäärien kanssa. Putkistojen kohdalla työssä on käsitelty kehityskohteeksi valittua erästä pääkolonni-osaan kuuluvaa linjastoa. Eri vaihtoehtoja on vertailtu teknistaloudelliselta näkökulma ja putkiston kohdalla on työssä päädytty geometrian muuttamiseen sekä koon kasvattamiseen. Työssä on myös esitetty kuumatypetysvaiheen uudelleen aikataulutusta alasajovaiheen nopeuttamiseksi sekä jatkotutkimusehdotuksia putkiston passivoimisesta, rautafluoridikalvon paikalleen jättämiseksi ja huoltopysäytyssyklin kehittämiseksi.

Impact of irrigation on yield and energy balance of the production of oil and cake of two sunflower varieties

The energy balance for the production of sunflower oil and cake was carried out during the agricultural and industrial stage phase, where it was considered a cold extraction by hydraulic pressing, with the plant location in a rural area with a radius of 30km range. Data on productivity was used in two varieties of sunflower (Helio 358 and Aguará 04) grown in different seasons (2007/2008, 2008/2009), under different irrigation levels. Data showed that irrigation resulted in an increase in productivity of both varieties, and the best response was observed for Aguará 04 variety. Moreover, the increased intensity of irrigation negatively affected the energy balance, reducing the ratio between energy produced and energy used in the production chain. The most significant inputs in the energy intake were fertilizer followed by diesel oil, when irrigation was not used for. When the irrigation technique was used, the most significant inputs, in order of representativeness, were: energy, fertilizer and equipment.

Performance of a diesel engine fueled with a preheated blend of soybean oil and petrodiesel

Brazil is doing a major effort to find alternatives to diesel oil as combustible. Some study lines are oriented to the development of vegetable oils used as fuel, as a source of getting cheaper and have higher energy density than the converted vegetable oils, and less risk of environmental contamination. The aim of this study was to evaluate the performance, the useful life of the lubricant and some components of a Diesel Cycle engine, with an electronic injection system, in a long-term test operating with a preheated blend (65°C) of 50% (v v-1) of soybean oil in petrodiesel. There was a reduction of the useful life of the injectors which presented failure because of high wear with 264 hours of operation and showed an increase in emissions of particulate matter (opacity) which may be assigned to the failures occurred in the injection system. An increase in the useful life of the lubricant, when compared with the literature was also observed. The electronic injection system may favor the burning of the tested fuel. The test was interrupted with 264 hours because of failures in the injection system.

Jatropha seed oil content and yield under different irrigation and potassium fertilization levels

The aim of this research was to evaluate the effects of different irrigation depths and potassium dosages, of Jatropha seed oil content and yield. The experimental design used was randomized blocks, in split-plots, with four replicates. The treatments were four water depths (plots) and four potassium dosages (subplots) applied through irrigation water. The water depths were applied based on the percentage of accumulated evaporation of a Class A (ECA) tank and of rainfall, as following: L0 = without irrigation, L40, L80 and L120, representing 40, 80 and 120% of the balance, respectively. The potassium dosages were K30, K60, K90 and K120 (30, 60, 90 and 120kg ha-1 of potassium, respectively). The oil extraction of samples was done through chemical extraction by organic solvent. The seeds used in this test were from the sampling of two seed productions from 2009, second year of crop production. It was possible to observe that irrigation use increased oil yield and decreased the oil content of Jatropha seed. Potassium fertilization did not influence oil content and yield. There was a relative increase of efficiency in water use producing oil until certain water depth, and after that there was a decrease.

Performance impact of the application of castor oil biodiesel in diesel engines

The use of renewable fuels, such as the biodiesel, can ease the demand of fossil fuel for the power generation and transportation fields in rural area. In this work, the performance impact of the application of castor oil biodiesel is evaluated with an automotive and a stationary diesel engine. The application of B20 and B10 biodiesel blends and pre-heated net biodiesel is considered. The viability of the employment of B10 and B20 blends to mobility and power generation was observed from dynamometric bench tests, where this blends performed similar to fossil diesel. With the pre-heated net biodiesel, however, a brake torque loss and a specific consumption increase were observed with relation to diesel fuel.

Modelling head loss along emitting pipes using dimensional analysis

Local head losses must be considered in estimating properly the maximum length of drip irrigation laterals. The aim of this work was to develop a model based on dimensional analysis for calculating head loss along laterals accounting for in-line drippers. Several measurements were performed with 12 models of emitters to obtain the experimental data required for developing and assessing the model. Based on the Camargo & Sentelhas coefficient, the model presented an excellent result in terms of precision and accuracy on estimating head loss. The deviation between estimated and observed values of head loss increased according to the head loss and the maximum deviation reached 0.17 m. The maximum relative error was 33.75% and only 15% of the data set presented relative errors higher than 20%. Neglecting local head losses incurred a higher than estimated maximum lateral length of 19.48% for pressure-compensating drippers and 16.48% for non pressure-compensating drippers.

Marketing-Sales Cooperation and its Relation on Direct Sales Performance: an Example of a Medium-sized Oil Company

The study touches upon marketing-sales departments’ cooperation and investigates marketing-sales cooperative model within the case company. So that research increases understanding of linkages between Marketing and Sales departments with an illustrative example of Russian medium-sized oil company (LLC Neste St. Petersburg), the subsidiary of Finnish-based Neste Oil. The empirical study is done from marketing and sales perspectives. And for sales main attention was brought to direct sales, both B2B and B2C. Research considers all five domains of cooperation, and among others, study reveals the attitude towards external (market) and internal (product) knowledge, and its mutual use by marketing and sales managers. A qualitative research method, participant observations, and in-depth interviews with upper-management made it possible to explore all facets of joint work. Moreover, research responses the changes in a model of cooperation between marketing and sales when moving from medium size to large company.

Corporate Social Responsibility in the Oil and Gas Industry: Environmental Management Systems as a Source of Sustainable Development

The environmental aspect of corporate social responsibility (CSR) expressed through the process of the EMS implementation in the oil and gas companies is identified as the main subject of this research. In the theoretical part, the basic attention is paid to justification of a link between CSR and environmental management. The achievement of sustainable competitive advantage as a result of environmental capital growth and inclusion of the socially responsible activities in the corporate strategy is another issue that is of special significance here. Besides, two basic forms of environmental management systems (environmental decision support systems and environmental information management systems) are explored and their role in effective stakeholder interaction is tackled. The most crucial benefits of EMS are also analyzed to underline its importance as a source of sustainable development. Further research is based on the survey of 51 sampled oil and gas companies (both publicly owned and state owned ones) originated from different countries all over the world and providing reports on sustainability issues in the open access. To analyze their approach to sustainable development, a specifically designed evaluation matrix with 37 indicators developed in accordance with the General Reporting Initiative (GRI) guidelines for non-financial reporting was prepared. Additionally, the quality of environmental information disclosure was measured on the basis of a quality – quantity matrix. According to results of research, oil and gas companies prefer implementing reactive measures to the costly and knowledge-intensive proactive techniques for elimination of the negative environmental impacts. Besides, it was identified that the environmental performance disclosure is mostly rather limited, so that the quality of non-financial reporting can be judged as quite insufficient. In spite of the fact that most of the oil and gas companies in the sample claim the EMS to be embedded currently in their structure, they often do not provide any details for the process of their implementation. As a potential for the further development of EMS, author mentions possible integration of their different forms in a single entity, extension of existing structure on the basis of consolidation of the structural and strategic precautions as well as development of a unified certification standard instead of several ones that exist today in order to enhance control on the EMS implementation.

Development of a Radiometer Front End for Detection of Oil Spill on Sea Surface

Kaikki kappaleet säteilevät sähkömagneettista energiaa. Radiometreillä voidaan mitata tätä säteilyä, ja mittausten avulla voidaan kaukokartoituksessa analysoida monia ilmakehään ja maan pintaan liittyviä ilmiöitä. Säteilyä kerätään useimmiten radiometriin kytketyn antennin avulla. Mikroaaltoalueella säteilystä saatava teho on verrannollinen kohteen kirkkauslämpötilaan. Kirkkauslämpötila on puolestaan verrannollinen kohteen fyysiseen lämpötilaan materiaalin emissiivisyyden kautta. Emissiivisyys voi vaihdella suuresti eri pintojen ja materiaalien välillä. Näin ollen mittaamalla kohteen kirkkauslämpötilaa saadaan tietoa sen ominaisuuksista. Mikroaaltoradiometrin avulla voidaan havaita öljyläikkä meren pinnalta, sekä määrittää öljyläikän paksuus. Öljy muodostaa ohuen kalvon meren pinnalla. Ohuen kalvon ylä- ja alapinnasta heijastuneet aallot kulkevat eri matkan, jonka seurauksena muodostuu interferenssikuvio. Interferenssi on joko konstruktiivinen tai destruktiivinen riippuen heijastusten vaihe-erosta. Pistetaajuudella tästä seuraa kalvon paksuudesta riippuva sinimuotoinen emissiivisyys. Mallintamalla tämä ilmiö riittävän tarkasti voidaan radiometrin mittaamaa kirkkauslämpötilaa verrata mallinnettuun arvoon ja täten määrittää öljykerroksen paksuus. Tässä työssä esitetään kahden radiometrin suunnittelu ja testaus. Työ rajoittuu radiometrien alustavaan testausvaiheeseen. Radiometrit on suunniteltu 36,5GHz sekä 89GHz taajuuksille. Työn suurin kontribuutio on radiometrien etupään suunnittelussa ja testauksessa, kalibraatiomenetelmien kehittämisessä sekä kylmäkuorman suunnittelussa. Lisäksi työssä esitetään radiometrien systeemisuunnittelu sekä siihen liittyvät simulaatiot.

Oil Transportation in the Gulf of Finland in 2020 and 2030

This study is part of the Minimizing risks of maritime oil transport by holistic safety strategies (MIMIC) project. The purpose of this study is to provide a current state analysis of oil transportation volumes in the Baltic Sea and to create scenarios for oil transportation in the Gulf of Finland for the years 2020 and 2030. Future scenarios and information about oil transportation will be utilized in the modelling of oil transportation risks, which will be carried out as part of the MIMIC project. Approximately 290 million tons of oil and oil products were transported in the Baltic Sea in 2009, of which 55% (160 million tons) via the Gulf of Finland. Oil transportation volumes in the Gulf of Finland have increased from 40 million to almost 160 million tonnes over the last ten years. In Russia and Estonia, oil transportation mainly consists of export transports of the Russian oil industry. In Finnish ports in the Gulf of Finland, the majority of oil traffic is concentrated to the port of Sköldvik, while the remainder mainly consists of different oil products for domestic use. Transit transports to/from Russia make up small volumes of oil transportation. The largest oil ports in the Gulf of Finland are Primorsk, Tallinn, St. Petersburg and Sköldvik. The basis for the scenarios for the years 2020 and 2030 is formed by national energy strategies, the EU`s climate and energy strategies as well other energy and transportation forecasts for the years 2020 and 2030. Three alternative scenarios were produced for both 2020 and 2030. The oil volumes are based on the expert estimates of nine specialists. The specialists gave three volumes for each scenario: the expected oil transport volumes, and the minimum and maximum volumes. Variations in the volumes between the scenarios are not large, but each scenario tends to have rather a large difference between the figures for minimum and maximum volumes. This variation between the minimum and maximum volumes ranges around 30 to 40 million tonnes depending on the scenario. On the basis of this study, no a dramatic increase in oil transportation volumes in the Gulf of Finland is to be expected. Most of the scenarios only forecasted a moderate growth in maritime oil transportation compared to the current levels. The effects of the European energy policy favouring renewable energy sources can be seen in the 2030 scenarios, in which the transported oil volumes are smaller than in the 2020 scenarios. In the Slow development 2020 scenario, oil transport volumes for 2020 are expected to be 170.6 Mt (million tonnes), in the Average development 2020 187.1 Mt and in the Strong development 2020 201.5 Mt. The corresponding oil volumes for the 2030 scenarios were 165 Mt for the Stagnating development 2030 scenario, 177.5 Mt for the Towards a greener society 2030 scenario and 169.5 Mt in the Decarbonising society 2030 scenario.