Abrasion resistance of concrete

This thesis describes an experimental study of the abrasion resistance of concrete at both the macro and micro levels. This is preceded by a review related to friction and wear, methods of test for assessing abrasion resistance, and factors influencing the abrasion resistance of concrete. A versatile test apparatus was developed to assess the abrasion resistance of concrete. This could be operated in three modes and a standardised procedure was established for all tests. A laboratory programme was undertaken to investigate the influence, on abrasion resistance, of three major factors - finishing techniques, curing regimes and surface treatments. The results clearly show that abrasion resistance was significantly affected by these factors, and tentative mechanisms were postulated to explain these observations. To substantiate these mechanisms, the concrete specimens from the macro-study were subjected to micro-structural investigation, using such techniques as 'Mercury Intrusion Forosimetry, Microhardness, Scanning Electron Microscopy, Petrography and Differential Thermal Analysis. The results of this programme clearly demonstrated that the abrasion resistance of concrete is primarily dependent on the microstructure of the concrete nearest to the surface. The viability of indirectly assessing the abrasion resistance was investigated using three non-destructive techniques - Ultrasonic Pulse Velocity, Schmidt Rebound Hardness, and the Initial Surface Absorption Test. The Initial Surface Absorption was found to be most sensitive to factors which were shown to have influenced the abrasion resistance of concrete. An extensive field investigation was also undertaken. The results were used to compare site and laboratorypractices, and the performance in the accelerated abrasion test with the service wear. From this study, criteria were developed for assessing the quality of concrete floor slabs in terms of abrasion resistance.

Analysis of Hue Spectra During Storage of Pepper (Capsicum annuum)

Color information is widely used in non-destructive quality assessment of perishable horticultural produces. The presented work investigated color changes of pepper (Capsicum annuum L.) samples received from retail system. The effect of storage temperature (10±2°C and 24±4°C) on surface color and firmness was analyzed. Hue spectra was calculated using sum of saturations. A ColorLite sph850 (400-700nm) spectrophotometer was used as reference instrument. Dynamic firmness was measured on three locations of the surface: tip cap, middle and shoulder. Significant effects of storage conditions and surface location on both color and firmness were observed. Hue spectra responded sensitively to color development of pepper. Prediction model (PLS) was used to estimate dynamic firmess based on hue spectra. Accuracy was very different depending on the location. Firmness of the tip cap was predicted with the highest accuracy (RMSEP=0.0335). On the other hand, middle region cannot be used for such purpose. Due to the simplicity and rapid processing, analysis of hue spectra is a promising tool for evaluation of color in postharvest and food industry.

Stereotype threat and the standardized testing experiences of African American children at an urban elementary school

Stereotype threat (Steele & Aronson, 1995) refers to the risk of confirming a negative stereotype about one’s group in a particular performance domain. The theory assumes that performance in the stereotyped domain is most negatively affected when individuals are more highly identified with the domain in question. As federal law has increased the importance of standardized testing at the elementary level, it can be reasonably hypothesized that the standardized test performance of African American children will be depressed when they are aware of negative societal stereotypes about the academic competence of African Americans. This sequential mixed-methods study investigated whether the standardized testing experiences of African American children in an urban elementary school are related to their level of stereotype awareness. The quantitative phase utilized data from 198 African American children at an urban elementary school. Both ex-post facto and experimental designs were employed. Experimental conditions were diagnostic and non-diagnostic testing experiences. The qualitative phase utilized data from a series of six focus group interviews conducted with a purposefully selected group of 4 African American children. The interview data were supplemented with data from 30 hours of classroom observations. Quantitative findings indicated that the stereotype threat condition evoked by diagnostic testing depresses the reading test performance of stereotype-aware African American children (F[1, 194] = 2.21, p < .01). This was particularly true of students who are most highly domain-identified with reading (F[1, 91] = 19.18, p < .01). Moreover, findings indicated that only stereotype-aware African American children who were highly domain-identified were more likely to experience anxiety in the diagnostic condition (F[1, 91] = 5.97, p < .025). Qualitative findings revealed 4 themes regarding how African American children perceive and experience the factors related to stereotype threat: (1) a narrow perception of education as strictly test preparation, (2) feelings of stress and anxiety related to the state test, (3) concern with what “others” think (racial salience), and (4) stereotypes. A new conceptual model for stereotype threat is presented, and future directions including implications for practice and policy are discussed.

Stereotype Threat and the Standardized Testing Experiences of African American Children at an Urban Elementary School

Stereotype threat (Steele & Aronson, 1995) refers to the risk of confirming a negative stereotype about one’s group in a particular performance domain. The theory assumes that performance in the stereotyped domain is most negatively affected when individuals are more highly identified with the domain in question. As federal law has increased the importance of standardized testing at the elementary level, it can be reasonably hypothesized that the standardized test performance of African American children will be depressed when they are aware of negative societal stereotypes about the academic competence of African Americans. This sequential mixed-methods study investigated whether the standardized testing experiences of African American children in an urban elementary school are related to their level of stereotype awareness. The quantitative phase utilized data from 198 African American children at an urban elementary school. Both ex-post facto and experimental designs were employed. Experimental conditions were diagnostic and non-diagnostic testing experiences. The qualitative phase utilized data from a series of six focus group interviews conducted with a purposefully selected group of 4 African American children. The interview data were supplemented with data from 30 hours of classroom observations. Quantitative findings indicated that the stereotype threat condition evoked by diagnostic testing depresses the reading test performance of stereotype-aware African American children (F[1, 194] = 2.21, p < .01). This was particularly true of students who are most highly domain-identified with reading (F[1, 91] = 19.18, p < .01). Moreover, findings indicated that only stereotype-aware African American children who were highly domain-identified were more likely to experience anxiety in the diagnostic condition (F[1, 91] = 5.97, p < .025). Qualitative findings revealed 4 themes regarding how African American children perceive and experience the factors related to stereotype threat: (1) a narrow perception of education as strictly test preparation, (2) feelings of stress and anxiety related to the state test, (3) concern with what “others” think (racial salience), and (4) stereotypes. A new conceptual model for stereotype threat is presented, and future directions including implications for practice and policy are discussed.

Improved image analysis based corrosion assessment using preprocessing techniques

The importance of non-destructive techniques (NDT) in structural health monitoring programmes is being critically felt in the recent times. The quality of the measured data, often affected by various environmental conditions can be a guiding factor in terms usefulness and prediction efficiencies of the various detection and monitoring methods used in this regard. Often, a preprocessing of the acquired data in relation to the affecting environmental parameters can improve the information quality and lead towards a significantly more efficient and correct prediction process. The improvement can be directly related to the final decision making policy about a structure or a network of structures and is compatible with general probabilistic frameworks of such assessment and decision making programmes. This paper considers a preprocessing technique employed for an image analysis based structural health monitoring methodology to identify sub-marine pitting corrosion in the presence of variable luminosity, contrast and noise affecting the quality of images. A preprocessing of the gray-level threshold of the various images is observed to bring about a significant improvement in terms of damage detection as compared to an automatically computed gray-level threshold. The case dependent adjustments of the threshold enable to obtain the best possible information from an existing image. The corresponding improvements are observed in a qualitative manner in the present study.

Tissue Equivalent Phantom Design for Optimization of a Coherent Scatter Imaging System

Scatter in medical imaging is typically cast off as image-related noise that detracts from meaningful diagnosis. It is therefore typically rejected or removed from medical images. However, it has been found that every material, including cancerous tissue, has a unique X-ray coherent scatter signature that can be used to identify the material or tissue. Such scatter-based tissue-identification provides the advantage of locating and identifying particular materials over conventional anatomical imaging through X-ray radiography. A coded aperture X-ray coherent scatter spectral imaging system has been developed in our group to classify different tissue types based on their unique scatter signatures. Previous experiments using our prototype have demonstrated that the depth-resolved coherent scatter spectral imaging system (CACSSI) can discriminate healthy and cancerous tissue present in the path of a non-destructive x-ray beam. A key to the successful optimization of CACSSI as a clinical imaging method is to obtain anatomically accurate phantoms of the human body. This thesis describes the development and fabrication of 3D printed anatomical scatter phantoms of the breast and lung.

The purpose of this work is to accurately model different breast geometries using a tissue equivalent phantom, and to classify these tissues in a coherent x-ray scatter imaging system. Tissue-equivalent anatomical phantoms were designed to assess the capability of the CACSSI system to classify different types of breast tissue (adipose, fibroglandular, malignant). These phantoms were 3D printed based on DICOM data obtained from CT scans of prone breasts. The phantoms were tested through comparison of measured scatter signatures with those of adipose and fibroglandular tissue from literature. Tumors in the phantom were modeled using a variety of biological tissue including actual surgically excised benign and malignant tissue specimens. Lung based phantoms have also been printed for future testing. Our imaging system has been able to define the location and composition of the various materials in the phantom. These phantoms were used to characterize the CACSSI system in terms of beam width and imaging technique. The result of this work showed accurate modeling and characterization of the phantoms through comparison of the tissue-equivalent form factors to those from literature. The physical construction of the phantoms, based on actual patient anatomy, was validated using mammography and computed tomography to visually compare the clinical images to those of actual patient anatomy.

Accuracy of computer-aided design/computer-assisted manufacture (CAD/CAM) fabricated dental restorations: a comparative study

Introduction: Computer-Aided-Design (CAD) and Computer-Aided-Manufacture (CAM) has been developed to fabricate fixed dental restorations accurately, faster and improve cost effectiveness of manufacture when compared to the conventional method. Two main methods exist in dental CAD/CAM technology: the subtractive and additive methods. While fitting accuracy of both methods has been explored, no study yet has compared the fabricated restoration (CAM output) to its CAD in terms of accuracy. The aim of this present study was to compare the output of various dental CAM routes to a sole initial CAD and establish the accuracy of fabrication. The internal fit of the various CAM routes were also investigated. The null hypotheses tested were: 1) no significant differences observed between the CAM output to the CAD and 2) no significant differences observed between the various CAM routes. Methods: An aluminium master model of a standard premolar preparation was scanned with a contact dental scanner (Incise, Renishaw, UK). A single CAD was created on the scanned master model (InciseCAD software, V2.5.0.140, UK). Twenty copings were then fabricated by sending the single CAD to a multitude of CAM routes. The copings were grouped (n=5) as: Laser sintered CoCrMo (LS), 5-axis milled CoCrMo (MCoCrMo), 3-axis milled zirconia (ZAx3) and 4-axis milled zirconia (ZAx4). All copings were micro-CT scanned (Phoenix X-Ray, Nanotom-S, Germany, power: 155kV, current: 60µA, 3600 projections) to produce 3-Dimensional (3D) models. A novel methodology was created to superimpose the micro-CT scans with the CAD (GOM Inspect software, V7.5SR2, Germany) to indicate inaccuracies in manufacturing. The accuracy in terms of coping volume was explored. The distances from the surfaces of the micro-CT 3D models to the surfaces of the CAD model (CAD Deviation) were investigated after creating surface colour deviation maps. Localised digital sections of the deviations (Occlusal, Axial and Cervical) and selected focussed areas were then quantitatively measured using software (GOM Inspect software, Germany). A novel methodology was also explored to digitally align (Rhino software, V5, USA) the micro-CT scans with the master model to investigate internal fit. Fifty digital cross sections of the aligned scans were created. Point-to-point distances were measured at 5 levels at each cross section. The five levels were: Vertical Marginal Fit (VF), Absolute Marginal Fit (AM), Axio-margin Fit (AMF), Axial Fit (AF) and Occlusal Fit (OF). Results: The results of the volume measurement were summarised as: VM-CoCrMo (62.8mm3 ) > VZax3 (59.4mm3 ) > VCAD (57mm3 ) > VZax4 (56.1mm3 ) > VLS (52.5mm3 ) and were all significantly different (p presented as areas with different colour. No significant differences were observed at the internal aspect of the cervical aspect between all groups of copings. Significant differences (p< M-CoCrMo Internal Occlusal, Internal Axial and External Axial 2 ZAx3 > ZAx4 External Occlusal, External Cervical 3 ZAx3 < ZAx4 Internal Occlusal 4 M-CoCrMo > ZAx4 Internal Occlusal and Internal Axial The mean values of AMF and AF were significantly (p M-CoCrMo and CAD > ZAx4. Only VF of M-CoCrMo was comparable with the CAD Internal Fit. All VF and AM values were within the clinically acceptable fit (120µm). Conclusion: The investigated CAM methods reproduced the CAD accurately at the internal cervical aspect of the copings. However, localised deviations at axial and occlusal aspects of the copings may suggest the need for modifications in these areas prior to fitting and veneering with porcelain. The CAM groups evaluated also showed different levels of Internal Fit thus rejecting the null hypotheses. The novel non-destructive methodologies for CAD/CAM accuracy and internal fit testing presented in this thesis may be a useful evaluation tool for similar applications.

Evaluating laser-driven Bremsstrahlung radiation sources for imaging and analysis of nuclear waste packages

A small scale sample nuclear waste package, consisting of a 28 mm diameter uranium penny encased in grout, was imaged by absorption contrast radiography using a single pulse exposure from an X-ray source driven by a high-power laser. The Vulcan laser was used to deliver a focused pulse of photons to a tantalum foil, in order to generate a bright burst of highly penetrating X-rays (with energy >500 keV), with a source size of <0.5 mm. BAS-TR and BAS-SR image plates were used for image capture, alongside a newly developed Thalium doped Caesium Iodide scintillator-based detector coupled to CCD chips. The uranium penny was clearly resolved to sub-mm accuracy over a 30 cm2 scan area from a single shot acquisition. In addition, neutron generation was demonstrated in situ with the X-ray beam, with a single shot, thus demonstrating the potential for multi-modal criticality testing of waste materials. This feasibility study successfully demonstrated non-destructive radiography of encapsulated, high density, nuclear material. With recent developments of high-power laser systems, to 10 Hz operation, a laser-driven multi-modal beamline for waste monitoring applications is envisioned.

Physical and chemical kinetics of structural build-up of cement suspensions

Abstract : The structural build-up of fresh cement-based materials has a great impact on their structural performance after casting. Accordingly, the mixture design should be tailored to adapt the kinetics of build-up given the application on hand. The rate of structural build-up of cement-based suspensions at rest is a complex phenomenon affected by both physical and chemical structuration processes. The structuration kinetics are strongly dependent on the mixture’s composition, testing parameters, as well as the shear history. Accurate measurements of build-up rely on the efficiency of the applied pre-shear regime to achieve an initial well-dispersed state as well as the applied stress during the liquid-solid transition. Studying the physical and chemical mechanisms of build-up of cement suspensions at rest can enhance the fundamental understanding of this phenomenon. This can, therefore, allow a better control of the rheological and time-dependent properties of cement-based materials. The research focused on the use of dynamic rheology in investigating the kinetics of structural build-up of fresh cement pastes. The research program was conducted in three different phases. The first phase was devoted to evaluating the dispersing efficiency of various disruptive shear techniques. The investigated shearing profiles included rotational, oscillatory, and combination of both. The initial and final states of suspension’s structure, before and after disruption, were determined by applying a small-amplitude oscillatory shear (SAOS). The difference between the viscoelastic values before and after disruption was used to express the degree of dispersion. An efficient technique to disperse concentrated cement suspensions was developed. The second phase aimed to establish a rheometric approach to dissociate and monitor the individual physical and chemical mechanisms of build-up of cement paste. In this regard, the non-destructive dynamic rheometry was used to investigate the evolutions of both storage modulus and phase angle of inert calcium carbonate and cement suspensions. Two independent build-up indices were proposed. The structural build-up of various cement suspensions made with different cement contents, silica fume replacement percentages, and high-range water reducer dosages was evaluated using the proposed indices. These indices were then compared to the well-known thixotropic index (Athix.). Furthermore, the proposed indices were correlated to the decay in lateral pressure determined for various cement pastes cast in a pressure column. The proposed pre-shearing protocol and build-up indices (phases 1 and 2) were then used to investigate the effect of mixture’s parameters on the kinetics of structural build-up in phase 3. The investigated mixture’s parameters included cement content and fineness, alkali sulfate content, and temperature of cement suspension. Zeta potential, calorimetric, spectrometric measurements were performed to explore the corresponding microstructural changes in cement suspensions, such as inter-particle cohesion, rate of Brownian flocculation, and nucleation rate. A model linking the build-up indices and the microstructural characteristics was developed to predict the build-up behaviour of cement-based suspensions The obtained results showed that oscillatory shear may have a greater effect on dispersing concentrated cement suspension than the rotational shear. Furthermore, the increase in induced shear strain was found to enhance the breakdown of suspension’s structure until a critical point, after which thickening effects dominate. An effective dispersing method is then proposed. This consists of applying a rotational shear around the transitional value between the linear and non-linear variations of the apparent viscosity with shear rate, followed by an oscillatory shear at the crossover shear strain and high angular frequency of 100 rad/s. Investigating the evolutions of viscoelastic properties of inert calcite-based and cement suspensions and allowed establishing two independent build-up indices. The first one (the percolation time) can represent the rest time needed to form the elastic network. On the other hand, the second one (rigidification rate) can describe the increase in stress-bearing capacity of formed network due to cement hydration. In addition, results showed that combining the percolation time and the rigidification rate can provide deeper insight into the structuration process of cement suspensions. Furthermore, these indices were found to be well-correlated to the decay in the lateral pressure of cement suspensions. The variations of proposed build-up indices with mixture’s parameters showed that the percolation time is most likely controlled by the frequency of Brownian collisions, distance between dispersed particles, and intensity of cohesion between cement particles. On the other hand, a higher rigidification rate can be secured by increasing the number of contact points per unit volume of paste, nucleation rate of cement hydrates, and intensity of inter-particle cohesion.

The Effect of Mark Enhancement Techniques on the Subsequent Detection of Saliva

There appears to be a limited but growing body of research on the sequential analysis/treatment of multiple types of evidence. The development of an integrated forensic approach is necessary to maximise evidence recovery and to ensure that a particular treatment is not detrimental to other types of evidence. This study aims to assess the effect of latent and blood mark enhancement techniques (e.g. fluorescence, ninhydrin, acid violet 17, black iron-oxide powder suspension) on the subsequent detection of saliva. Saliva detection was performed by means of a presumptive test (Phadebas®) in addition to analysis by a rapid stain identification (RSID) kit test and confirmatory DNA testing. Additional variables included a saliva depletion series and a number of different substrates with varying porosities as well as different ageing periods. Examination and photography under white light and fluorescence was carried out prior to and after chemical enhancement All enhancement techniques (except Bluestar® Forensic Magnum luminol) employed in this study resulted in an improved visualisation of the saliva stains, although the inherent fluorescence of saliva was sometimes blocked after chemical treatment. The use of protein stains was, in general, detrimental to the detection of saliva. Positive results were less pronounced after the use of black iron-oxide powder suspension, cyanoacrylate fuming followed by BY40 and ninhydrin when compared to the respective positive controls. The application of Bluestar® Forensic Magnum luminol and black magnetic powder proved to be the least detrimental, with no significant difference between the test results and the positive controls. The use of non-destructive fluorescence examination provided good visualisation; however, only the first few marks in the depletion were observed. Of the samples selected for DNA analysis only depletion 1 samples contained sufficient DNA quantity for further processing using standard methodology. The 28 day delay between sample deposition and collection resulted in a 5-fold reduction in the amount of useable DNA. When sufficient DNA quantities were recovered, enhancement techniques did not have a detrimental effect on the ability to generate DNA profiles. This study aims to contribute to a strategy for maximising evidence recovery and efficiency for the detection of latent marks and saliva. The results demonstrate that most of the enhancement techniques employed in this study were not detrimental to the subsequent detection of saliva by means of presumptive, confirmative and DNA tests.

Hyperspectral sensing to detect the impact of herbicide drift on cotton growth and yield

Yield loss in crops is often associated with plant disease or external factors such as environment, water supply and nutrient availability. Improper agricultural practices can also introduce risks into the equation. Herbicide drift can be a combination of improper practices and environmental conditions which can create a potential yield loss. As traditional assessment of plant damage is often imprecise and time consuming, the ability of remote and proximal sensing techniques to monitor various bio-chemical alterations in the plant may offer a faster, non-destructive and reliable approach to predict yield loss caused by herbicide drift. This paper examines the prediction capabilities of partial least squares regression (PLS-R) models for estimating yield. Models were constructed with hyperspectral data of a cotton crop sprayed with three simulated doses of the phenoxy herbicide 2,4-D at three different growth stages. Fibre quality, photosynthesis, conductance, and two main hormones, indole acetic acid (IAA) and abscisic acid (ABA) were also analysed. Except for fibre quality and ABA, Spearman correlations have shown that these variables were highly affected by the chemical. Four PLS-R models for predicting yield were developed according to four timings of data collection: 2, 7, 14 and 28 days after the exposure (DAE). As indicated by the model performance, the analysis revealed that 7 DAE was the best time for data collection purposes (RMSEP = 2.6 and R2 = 0.88), followed by 28 DAE (RMSEP = 3.2 and R2 = 0.84). In summary, the results of this study show that it is possible to accurately predict yield after a simulated herbicide drift of 2,4-D on a cotton crop, through the analysis of hyperspectral data, thereby providing a reliable, effective and non-destructive alternative based on the internal response of the cotton leaves.

Cork structural characteristics and their influence on the oxygen ingress through wine stoppers

Doutoramento em Engenharia Florestal e dos Recursos Naturais - Instituto Superior de Agronomia - UL

USING INDICATORS OF BIOTIC INTEGRITY FOR ASSESSMENT OF STREAM CONDITION

Multiple indices of biotic integrity and biological condition gradient models have been developed and validated to assess ecological integrity in the Laurentian Great Lakes Region. With multiple groups such as Tribal, Federal, and State agencies as well as scientists and local watershed management or river-focused volunteer groups collecting data for bioassessment it is important that we determine the comparability of data and the effectiveness of indices applied to these data for assessment of natural systems. We evaluated the applicability of macroinvertebrate and fish community indices for assessing site integrity. Site quality (i.e., habitat condition) could be classified differently depending on which index was applied. This highlights the need to better understand the metrics driving index variation as well as reference conditions for effective communication and use of indices of biotic integrity in the Upper Midwest. We found the macroinvertebrate benthic community index for the Northern Lakes and Forests Ecoregion and a coldwater fish index of biotic integrity for the Upper Midwest were most appropriate for use in the Big Manistee River watershed based on replicate sampling, ability to track trends over time and overall performance. We evaluated three sites where improper road stream crossings (culverts) were improved by replacing them with modern full-span structures using the most appropriate fish and macroinvertebrate IBIs. We used a before-after-control-impact paired series analytical design and found mixed results, with evidence of improvement in biotic integrity based on macroinvertebrate indices at some of the sites while most sites indicated no response in index score. Culvert replacements are often developed based on the potential, or the perception, that they will restore ecological integrity. As restoration practitioners, researchers and managers, we need to be transparent in our goals and objectives and monitor for those results specifically. The results of this research serve as an important model for the broader field of ecosystem restoration and support the argument that while biotic communities can respond to actions undertaken with the goal of overall restoration, practitioners should be realistic in their expectations and claims of predicted benefit, and then effectively evaluate the true impacts of the restoration activities.

Combination of product quality management and exports: The case of Colombian fruits companies

Quality management provides to companies a framework to improve quality in overall systems, reduction of costs, reallocation of resources efficiently, correct planning of strategies, prevent or correct errors in the right time and increase the performance of companies. In this text, we discuss the different theories in this field, their obligatory or non-obligatory compliance, the importance of quality management for exporting companies and a case study of a Colombian firm that its main objective is to manage quality. In conclusion, we find out that there is different types of quality management systems such as Juran’s trilogy, Deming 14 points, Six sigma, HACCP, and so on; also that companies have to manage suppliers and that quality has a positive influence on exports volume; in the case of Colombian small and medium enterprises, it can be mentioned that the majority has implemented tools regarding quality management but is not enough.

Starch, growth, and development in cuttings of rootstock "Paulsen 1103" from plants infested with ground pearl.

ABSTRACT The ground pearl, Eurhizococcus brasiliensis, is considered an important pest of vineyards in southern Brazil, with affected plants exhibiting leaf chlorosis, reduction in vigor, fading, and death. This study evaluated the quality of hardwood cuttings produced from plants infected (I) and not infected (NI) by ground pearl. ?Paulsen 1103? (Vitis berlandieri × Vitis rupestris) plants were grown for 29 months in brick-built raised beds either infested or not infested by ground pearl; then, 12 one-year-old branches with a maximum of 12 buds each were cut from each plant, subdivided into three portions (4 buds cutting-1), and subjected to destructive and nondestructive testing. Destructive testing comprised determining fresh and dry weight, length, internode diameters, and percentage of starch. Nondestructive testing comprised assessing the potential for bud sprouting and shoot development. Each mother plant in the I and NI beds was considered a replicate, with a total of 360 cuttings per treatment. It was observed that cuttings from infected plants had significantly lower (P<0.05) internode diameter, length, and fresh and dry weight than those of the uninfected plants. The percentage of starch content of the cuttings did not differ significantly. All cuttings showed the same percentage (100%) of bud breaking and no changes in growth and development of seedlings regardless of source. Given these results, it was concluded that vines of ?Paulsen 1103? infested with ground pearl produce smaller cuttings than those of uninfected plants but with no reduction in bud break percentage or seedling development. Key words: Margarodidae, Vitaceae, insect?plant interaction, carbohydrates. RESUMO A pérola-da-terra, Eurhizococcus brasiliensis, tem sido considerada uma importante praga dos vinhedos no sul do Brasil, sendo que as plantas atacadas manifestam clorose foliar, redução no vigor, definhamento e morte. Este trabalho teve por objetivo avaliar a qualidade de estacas lenhosas produzidas a partir do contraste de videiras infestadas (I) e não infestadas (NI) por pérola-da-terra. Após 29 meses de cultivo em canteiros de alvenaria, em presença ou ausência de pérola-da-terra, cada planta da variedade ?Paulsen 1103? (Vitis berlandieri × Vitis rupestris) foi submetida à retirada de 12 ramos de ano, com no máximo 12 gemas cada, sendo subdivididos em três porções 4 gemas estaca-1) e submetidos a avaliações destrutivas e não destrutivas. As destrutivas consistiram em determinar massas fresca e seca, comprimento, diâmetro de entrenós e percentual de amido. As avaliações não estrutivas consistiram em testar o potencial de brotação e desenvolvimento das estacas. Cada planta matriz dos canteiros I e NI foi considerada uma repetição, totalizando 360 estacas por tratamento. As estacas das plantas infestadas tiveram uma redução (P<0,05), em relação às não infestadas, em diâmetro, comprimento e massas fresca e seca. Não houve contraste significativo do percentual de amido avaliado das estacas. Quanto à brotação, destaca-se que todas as estacas apresentaram o mesmo percentual (100%), independente da origem, sem alterações no desenvolvimento e crescimento das mudas. Diante desses resultados, salienta-se que videiras ?Paulsen 1103? infestadas por pérola-da-terra produzem estacas menores, porém não há comprometimento no percentual de brotação e desenvolvimento das mudas, quando comparadas com plantas não infestadas. Palavras-chave: Margarodidae, Vitaceae, interação inseto-planta, carboidrato