Composition and structure variation for magnetron sputtered tantalum oxynitride thin films, as function of deposition parameters

Tantalum oxynitride thin films were produced by magnetron sputtering. The films were deposited usinga pure Ta target and a working atmosphere with a constant N2/O2ratio. The choice of this constant ratiolimits the study concerning the influence of each reactive gas, but allows a deeper understanding of theaspects related to the affinity of Ta to the non-metallic elements and it is economically advantageous.This work begins by analysing the data obtained directly from the film deposition stage, followed bythe analysis of the morphology, composition and structure. For a better understanding regarding theinfluence of the deposition parameters, the analyses are presented by using the following criterion: thefilms were divided into two sets, one of them produced with grounded substrate holder and the otherwith a polarization of −50 V. Each one of these sets was produced with different partial pressure of thereactive gases P(N2+ O2). All the films exhibited a O/N ratio higher than the N/O ratio in the depositionchamber atmosphere. In the case of the films produced with grounded substrate holder, a strong increaseof the O content is observed, associated to the strong decrease of the N content, when P(N2+ O2) is higherthan 0.13 Pa. The higher Ta affinity for O strongly influences the structural evolution of the films. Grazingincidence X-ray diffraction showed that the lower partial pressure films were crystalline, while X-rayreflectivity studies found out that the density of the films depended on the deposition conditions: thehigher the gas pressure, the lower the density. Firstly, a dominant -Ta structure is observed, for lowP(N2+ O2); secondly a fcc-Ta(N,O) structure, for intermediate P(N2+ O2); thirdly, the films are amorphousfor the highest partial pressures. The comparison of the characteristics of both sets of produced TaNxOyfilms are explained, with detail, in the text.

Imidazo-benzocrown ether functionalised amino acids: synthesis and fluorimetric chemosensing studies with metal cations

Comunicação em painel - P59

Study of the electrical behavior of nanostructured Ti–Ag thin films, prepared by glancing angle deposition

Aiming at biosignal acquisition for bioelectrodes application, Ti-Ag thin films were produced by GLAD, in order to tailor their electromechanical properties. The electrical behaviour of the sculptured Ti-Ag thin films was studied with increasing annealing temperatures. The results revealed a good correlation with the set of morphological features displayed. With the increase of the vapour flux angle, a more defined structure was obtained, as well as a more porous morphology, which increased the electrical resistivity of the coatings. An important point consists in the recrystallization of Ti-Ag intermetallic phases due to the temperature increase (between 558 K and 773 K), which resulted in a sharp decrease of the electrical resistivity values.

Elaboration et caractérisation des nanocristaux de Zn F O enfouis 1-x x dans des diélectriques pour des applications en spin-électronique

Tese de Doutoramento em Ciências - Especialidade em Física

Toxicity induced by a metal mixture (Cd, Pb and Zn) in the yeast Pichia kudriavzevii: The role of oxidative stress

The present work aims to contribute for the elucidation of the role of oxidative stress in the toxicity associated with the exposure of Pichia kudriavzevii to multi-metals (Cd, Pb and Zn). Cells of the non-conventional yeast P. kudriavzevii exposed for 6 h to the action of multi-metals accumulated intracellular reactive oxygen species (ROS), evaluated through the oxidation of the probe 2,7-dichlorodihydrofluorescein diacetate. A progressive loss of membrane integrity (monitored using propidium iodide) was observed in multi-metal-treated cells. The triggering of intracellular ROS accumulation preceded the loss of membrane integrity. These results suggest that the disruption of membrane integrity can be attributed to the oxidative stress. The exposure of yeast cells to single metal showed that, under the concentrations tested, Pb was the metal responsible for the induction of the oxidative stress. Yeast cells coexposed to an antioxidant (ascorbic acid) and multi-metals did not accumulate intracellular ROS, but loss proliferation capacity. Together, the data obtained indicated that intracellular ROS accumulation contributed to metal toxicity, namely for the disruption of membrane integrity of the yeast P. kudriavzevii. It was proposed that Pb toxicity (the metal responsible for the toxic symptoms under the conditions tested) result from the combination of an ionic mechanism and the intracellular ROS accumulation.

Producción de diamante por CVD (Chemical Vapour Deposition)

A fines de la década del '60 un grupo de investigadores rusos pudo obtener diamante a partir de experimentos con reacciones en fase vapor a bajas presiones de los gases envueltos en el proceso. En 1976 Derjagin et al. mostraron que la nucleación de diamante es posible sobre sustratos de Cu y en 1982 Matsumoto demuestra que la nucleación y crecimiento continuo a bajas presiones de diamante es posible sobre diversos substratos. Las especiales propiedades del diamante (D): dureza, elevado punto de fusión, inercia química, así como elevada conductividad del calor, sonido y de señales ópticas, ubican a este material como una de las prioridades de desarrollo e investigación de grupos de excelencia en el mundo entero. (...) Objetivos Generales y Específicos: El objetivo de este proyecto se basa en la construcción de un reactor para CVD (Chemical Vapour Deposition) y de los elementos auxiliares necesarios para producir diamante sintético por este método. Determinando los parámetros que controlan el proceso: mezcla de gases adecuada, temperatura de substrato, temperatura del plasma, presión parcial de los gases, vacío necesario y otros. En la primera etapa de 2 años se priorizará la puesta a punto del método, para luego pasar al estudio de las diferentes aplicaciones tecnológicas necesarias para la región. Específicamente, en el tercer año se tratará de generar diamantes como recubrimientos para herramientas de corte, así como para trapanos de velocidad, aprovechando residuos para la industria de abrasivos. Los objetivos generales no se cirscuncriben sólo al hecho de montar un reactor en laboratorio para CVD, sino una vez encontrados los parámetros que gobiernan esta técnica, producir diamante sintético para aplicaciones en la industria de herramientas de corte, micrófonos y óptica. Otro objetivo general de importancia es la formación de recursos humanos en técnicas de vacío, ingeniería de superficie y tecnología de plasma a través del personal y de los estudiantes involucrados en el proyecto, así como los participantes en cátedras del Departamento de Mecánica. En cuanto a los objetivos específicos para los dos primeros años, es preparar, construir y poner a punto un reactor de laboratorio de filamento caliente (Hot filament) por tecnología de plasma tipo CVD para obtener diamante sintético a partir de gases.

Intervenção coronária percutânea utilizando Full Metal Jacket com stents farmacológicos: eventos cardíacos adversos maiores em um ano

FUNDAMENTO: O benefício clínico de intervenção coronária percutânea (ICP) para lesões coronárias longas é incerto; além disso, foram levantadas dúvidas questões sobre a sua segurança. OBJETIVO: Avaliar os preditores de eventos cardíacos adversos maiores (ECAM) associados à ICP utilizando Full Metal Jacket (FMJ), definido como a sobreposição de stents farmacológicos (SF) medindo >60 mm de comprimento, para lesões muito longas. MÉTODOS: Foram incluídos 136 pacientes consecutivos com lesões coronárias longas, requerendo FMJ em nosso cadastro de centro único. O desfecho primário incluiu a ocorrência combinada de todas as causas de morte, infarto do miocárdio (IM) e revascularização do vaso alvo (RVA). Variáveis demográficas, clínicas, angiográficas e de procedimento foram avaliadas por meio de análise de regressão de Cox para determinar os preditores independentes de desfecho. RESULTADOS: O comprimento médio do stent por lesão foi de 73,2 ± 12,3 mm e o diâmetro médio do vaso de referência foi de 2,9 ± 0,6 mm. O sucesso angiográfico foi de 96,3%. A ausência de ECAM foi de 94,9% em 30 dias e 85,3% em um ano. No acompanhamento de um ano, a taxa de mortalidade por todas as causas foi de 3,7% (1,5% por mortes cardíacas), a taxa de IM foi de 3,7%, e a incidência de trombose de stent (TS) definitiva ou provável foi de 2,9%. O gênero feminino [risco relativo (RR), 4,40; intervalo de confiança de 95% (IC), 1,81-10,66, p = 0,001) e ICP de artéria coronária não direita (RR, 3,49; p = 0,006; IC 95%, 1,42-8,59) foram preditores independentes de ECAM em um ano. A ausência de eventos adversos em um ano foi maior em pacientes com angina estável submetidos à ICP (RR, 0,33; IC 95% 0,13-0,80, p = 0,014). CONCLUSÕES: A ICP utilizando FMJ com SF para lesões muito longas foi eficaz, mas associada a uma alta taxa de TS em acompanhamento de um ano. No entanto, a taxa de mortalidade cardíaca, IM não relacionado a procedimento, e ECAM foi relativamente baixa. ICP de vaso coronário alvo, apresentação clínica, e gênero feminino são novos fatores clínicos contemporâneos que parecem apresentar efeitos adversos sobre o resultado da ICP utilizando FMJ para lesões longas.

Long-term Outcomes of Drug-eluting versus Bare-metal stent for ST-elevation Myocardial Infarction

Background:Long-term outcomes of drug-eluting stents (DES) versus bare-metal stents (BMS) in patients with ST-segment elevation myocardial infarction (STEMI) remain uncertain.Objective:To investigate long-term outcomes of drug-eluting stents (DES) versus bare-metal stents (BMS) in patients with ST-segment elevation myocardial infarction (STEMI).Methods:We performed search of MEDLINE, EMBASE, the Cochrane library, and ISI Web of Science (until February 2013) for randomized trials comparing more than 12-month efficacy or safety of DES with BMS in patients with STEMI. Pooled estimate was presented with risk ratio (RR) and its 95% confidence interval (CI) using random-effects model.Results:Ten trials with 7,592 participants with STEMI were included. The overall results showed that there was no significant difference in the incidence of all-cause death and definite/probable stent thrombosis between DES and BMS at long-term follow-up. Patients receiving DES implantation appeared to have a lower 1-year incidence of recurrent myocardial infarction than those receiving BMS (RR = 0.75, 95% CI 0.56 to 1.00, p= 0.05). Moreover, the risk of target vessel revascularization (TVR) after receiving DES was consistently lowered during long-term observation (all p< 0.01). In subgroup analysis, the use of everolimus-eluting stents (EES) was associated with reduced risk of stent thrombosis in STEMI patients (RR = 0.37, p=0.02).Conclusions:DES did not increase the risk of stent thrombosis in patients with STEMI compared with BMS. Moreover, the use of DES did lower long-term risk of repeat revascularization and might decrease the occurrence of reinfarction.

Spectral Analysis Related to Bare-Metal and Drug-Eluting Coronary Stent Implantation

Background: The autonomic nervous system plays a central role in cardiovascular regulation; sympathetic activation occurs during myocardial ischemia. Objective: To assess the spectral analysis of heart rate variability during stent implantation, comparing the types of stent. Methods: This study assessed 61 patients (mean age, 64.0 years; 35 men) with ischemic heart disease and indication for stenting. Stent implantation was performed under Holter monitoring to record the spectral analysis of heart rate variability (Fourier transform), measuring the low-frequency (LF) and high-frequency (HF) components, and the LF/HF ratio before and during the procedure. Results: Bare-metal stent was implanted in 34 patients, while the others received drug-eluting stents. The right coronary artery was approached in 21 patients, the left anterior descending, in 28, and the circumflex, in 9. As compared with the pre-stenting period, all patients showed an increase in LF and HF during stent implantation (658 versus 185 ms2, p = 0.00; 322 versus 121, p = 0.00, respectively), with no change in LF/HF. During stent implantation, LF was 864 ms2 in patients with bare-metal stents, and 398 ms2 in those with drug-eluting stents (p = 0.00). The spectral analysis of heart rate variability showed no association with diabetes mellitus, family history, clinical presentation, beta-blockers, age, and vessel or its segment. Conclusions: Stent implantation resulted in concomitant sympathetic and vagal activations. Diabetes mellitus, use of beta-blockers, and the vessel approached showed no influence on the spectral analysis of heart rate variability. Sympathetic activation was lower during the implantation of drug-eluting stents.

Simulation of metal quenching processes for the minimization of distortion and stresses

Quenching process, TRIP, J2-plasticity theory, phase transition, distortion

Influence of water quality and kind of metal in the secondary cooling zone of casting process

Magdeburg, Univ., Fak. für Verfahrens- und Systemtechnik, Diss., 2012

Growth of semi-polar GaN on high index silicon (11h) substrates by metal organic vapor phase epitaxy

Magdeburg, Univ., Fak. für Naturwiss., Diss., 2014

Cytochemical characterization of gill and hepatopancreatic cells of the crab Ucides cordatus (Crustacea, Brachyura) validated by cell metal transport

Ucides cordatus (Linnaeus, 1763) is a hypo-hyper-regulating mangrove crab possessing gills for respiratory and osmoregulatory processes, separated in anterior and posterior sections. They also have hepatopancreas, which is responsible for digestion and absorption of nutrients and detoxification of toxic metals. Each of these organs has specific cells that are important for in vitro studies in cell biology, ion and toxic metals transport. In order to study and characterize cells from gills and hepatopancreas, both were separated using a Sucrose Gradient (SG) from 10 to 40% and cells in each gradient were characterized using the vital mitochondrial dye DASPEI (2-(4-dimethylaminostyryl)-N- ethylpyridinium iodide) and Trichrome Mallory's stain. Both in 20 and 40% SG for gill cells and 30% SG for hepatopancreatic cells, a greater number of cells were colored with DASPEI, indicating a larger number of mitochondria in these cells. It is concluded that the gill cells present in 20% and 40% SG are Thin cells, responsible for respiratory processes and Ionocytes responsible for ion transport, respectively. For hepatopancreatic cells, the 30% SG is composed of Fibrillar cells that possess larger number of membrane ion and nutrient transporters. Moreover, the transport of toxic metal cadmium (Cd) by isolated hepatopancreatic cells was performed as a way of following cell physiological integrity after cell separation and to study differences in transport among the cells. All hepatopancreatic cells were able to transport Cd. These findings are the first step for further work on isolated cells of these important exchange epithelia of crabs, using a simple separation method and to further develop successful in vitro cell culture in crabs.

Comportamiento tribomecánico de sistemas de sustrato: recubrimiento duros

En aplicaciones como la conformación en frío, donde los metales duros recubiertos con películas de naturaleza cerámica son ampliamente empleados, la existencia de un contacto mecánico repetitivo induce tensiones Hertzianas y origina el fallo por fatiga. En este trabajo, se investigan diversos recubrimientos cerámicos depositados por deposición física desde fase vapor sobre calidades diferentes de metal duro y un acero rápido pulvimetalúrgico para evaluar sus respectivas respuesta al contacto y comportamiento a fatiga. El trabajo experimental incluye la caracterización de los sistemas mediante ensayos de rayado y nanoindentación y la evaluación de las curvas tensión-deformación de indentación esférica de los sustratos, tanto desnudos como recubiertos, poniendo especial atención en determinar las tensiones de contacto críticas asociadas a la deformación plástica y a la aparición de grietas circulares en la superficie recubierta. A este estudio, le siguen numerosos ensayos a fatiga a cargas inferiores a aquéllas identificadas como críticas bajo carga monotónica y para un número de ciclos comprendido entre 1.000 y 1.000.000 de ciclos. Los resultados experimentales indican que las películas cerámicas no parecen desempeñar un papel relevante en la aparición de la cedencia plástica, siendo la deformación plástica global controlada por la deformación del sustrato. No obstante, para tensiones elevadas de indentación durante el régimen plástico, existe la aparición de grietas circulares en los recubrimientos cerámicos. Además, la aparición de las mismas es sensible a la fatiga por contacto. Este análisis mecánico se complementa con una inspección detallada del daño generado en profundidad y superficie.