EFEITO DA ESTRUTURA MOLECULAR DE LIGANTES DE SUPERFÍCIE EM PONTOS QUÂNTICOS DE CdTe DISPERSOS EM ÁGUA

Water-soluble CdTe quantum dots are synthesized to investigate how short-chain surface ligands bearing -SH, -COOH, and -NH2 groups interact with CdTe during nucleation/growth processes. Their optical properties and colloidal stability after the ligand exchange are also investigated. We then characterize the resulting CdTe by fluorescence, UV–Vis absorption, and infrared spectroscopies. The stability of the colloidal dispersions was determined by their Zeta potentials. The results show that in the synthesis of water-soluble CdTe, surface ligands with at least two functional groups are required and the hard/soft character of them is an important factor in the stability of CdTe.

Flow-batch analyser for preparation of calibration standard mixtures in simultaneous multicomponent spectrometric analysis

The application of multivariate calibration techniques to multicomponent analysis by UV-VIS molecular absorption spectrometry is a powerful tool for simultaneous determination of several chemical species. However, when this methodology is accomplished manually, it is slow and laborious, consumes high amounts of reagents and samples, is susceptible to contaminations and presents a high operational cost. To overcome these drawbacks, a flow-batch analyser is proposed in this work. This analyser was developed for automatic preparation of standard calibration and test (or validation) mixtures. It was applied to the simultaneous determination of Cu2+, Mn2+ and Zn2+ in polyvitaminic and polymineral pharmaceutical formulations, using 4-(2-piridilazo) resorcinol as reagent and a UV-VIS spectrophotometer with a photodiode array detector. The results obtained with the proposed system are in good agreement with those obtained by flame atomic absorption spectrometry, which was employed as reference method. With the proposed analyser, the preparation of calibration and test mixtures can be accomplished about four hours, while the manual procedure requires at least two days. Moreover, it consumes smaller amounts of reagents and samples than the manual procedure. After the preparation of calibration and test mixtures, 60 samples h-1 can be carried out with the proposed flow-batch analyser.

Ultrasuodatusmembraanin modifiointi entsyymeillä suodatusominaisuuksien parantamiseksi

Tämän diplomityön tarkoituksena oli kiinnittää lakkaasientsyymi polyeetterisulfonimembraaniin suodatusominaisuuksien parantamiseksi. Lakkaasientsyymin tiedetään pilkkovan ligniiniä ja kiinnittämällä lakkaasientsyymi membraaniin tavoiteltiin ligniinin aiheuttaman membraanin likaantumisen vähentämistä. Tällöin vältyttäisiin lisäksi erilliseltä esikäsittely vaiheelta ja voitaisiin saada puhtaampi lopputuote. Lakkaasientsyymivalmisteena tutkimuksessa käytettiin Novozym® 51003 ja ristisilloittajana käytettiin glutaarialdehydiä. Vapaan ja kiinnitetyn lakkaasientsyymin aktiivisuuden määritettiin 2,2-atso-bis(3- etyylibentsotiatsolyyli-6-sulfonihappo):n avulla. Lakkaasin kiinnittymistä membraaniin tutkittiin ATR-FTIR spektroskoopilla kiinnittymisen varmentamiseksi. Lakkaasi modifioituja membraaneja testattiin koivu-uute suodatuksella ja adsorptio kokeella. Lakkaasientsyymi saatiin kiinnitettyä membraaniin ristisilloittajan avulla, mutta lakkaasilla modifioitujen membraanien vesivuot laskivat noin puoleen alkuperäisestä. Koivu-uuteen suodatuksissa modifioidusta membraanista ei saatu permeaattia lävitse, mutta adsorptiokokeen tulosten perusteella voidaan todeta lakkaasientsyymin pilkkoneen ligniiniä. Kiinnitetyn lakkaasin aktiivisuus vaihteli rinnakkaisten määritysten välillä, minkä vuoksi lakkaasin kiinnitysmekanismin lisätutkiminen olisi tarpeen luotettavimpien tulosten saamiseksi.

POCN-type Pincer Complexes of NiII and NiIII : synthesis, reactivities, catalytic activities and physical properties

Cette thèse décrit la synthèse, la caractérisation, les réactivités, et les propriétés physiques de complexes divalents et trivalents de Ni formés à partir de nouveaux ligands «pincer» de type POCN. Les ligands POCN de type amine sont préparés d’une façon simple et efficace via l’amination réductrice de 3-hydroxybenzaldéhyde avec NaBH4 et plusieurs amines, suivie par la phosphination de l’amino alcool résultant pour installer la fonction phosphinite (OPR2); le ligand POCN de type imine 1,3-(i-Pr)2PC6H4C(H)=N(CH2Ph) est préparé de façon similaire en faisant usage de PhCH2NH2 en l’absence de NaBH4. La réaction de ces ligands «pincer» de type POCN avec NiBr2(CH3CN)x en présence d’une base résulte en un bon rendement de la cyclométalation du lien C-H situé en ortho aux fonctions amine et phosphinite. Il fut découvert que la base est essentielle pour la propreté et le haut rendement de la formation des complexes «pincer» désirés. Nous avons préparé des complexes «pincer» plan- carrés de type POCN, (POCNRR΄)NiBr, possédant des fonctions amines secondaires et tertiaires qui démontrent des réactivités différentes selon les substituants R et R΄. Par exemple, les complexes possédant des fonctions amines tertiaires ArCH2NR2 (NR2= NMe2, NEt2, and morpholinyl) démontrent des propriétés rédox intéressantes et pourraient être convertis en leurs analogues trivalents (POCNR2)NiBr2 lorsque réagis avec Br2 ou N-bromosuccinimide (NBS). Les complexes trivalents paramagnétiques à 17 électrons adoptent une géométrie de type plan-carré déformée, les atomes de Br occupant les positions axiale et équatoriale. Les analyses «DSC» et «TGA» des ces composés ont démontré qu’ils sont thermiquement stables jusqu’à ~170 °C; tandis que la spectroscopie d’absorption en solution a démontré qu’ils se décomposent thermiquement à beaucoup plus basse température pour regénérer les complexes divalents ne possédant qu’un seul Br; l’encombrement stérique des substitutants amines accélère cette route de décomposition de façon significative. Les analogues NMe2 et N(morpholinyl) de ces espèces de NiIII sont actifs pour catalyser la réaction d’addition de Kharasch, de CX4 à des oléfines telles que le styrène, tandis qu’il fut découvert que l’analogue le moins thermiquement stable (POCNEt2)Ni est complètement inerte pour catalyser cette réaction. Les complexes (POCNRH)NiBr possédant des fonctions amines secondaires permettent l’accès à des fonctions amines substituées de façon non symétrique via leur réaction avec des halogénures d’alkyle. Un autre avantage important de ces complexes réside dans la possibilité de déprotonation pour préparer des complexes POCN de type amide. De telles tentatives pour déprotoner les fonctions NRH nous ont permis de préparer des espèces dimériques possédant des ligands amides pontants. La nature dimérique des ces complexes [P,C,N,N-(2,6-(i-Pr)2PC6H3CH2NR)Ni]2 (R= PhCH2 et Ph) fut établie par des études de diffraction des rayons-X qui ont démontré différentes géométries pour les cœurs Ni2N2 selon le substituant N : l’analogue (PhCH2)N possède une orientation syn des substitutants benzyles et un arrangement ressemblant à celui du cyclobutane du Ni et des atomes d’azote, tandis que l’analogue PhN adopte un arrangement de type diamant quasi-planaire des atomes du Ni et des atomes d’azote et une orientation anti des substituants phényles. Les espèces dimériques ne se dissocient pas en présence d’alcools, mais elles promouvoient l’alcoolyse catalytique de l’acrylonitrile. De façon intéressante, les rendements de ces réactions sont plus élevés avec les alcools possédant des fonctions O-H plus acides, avec un nombre de «turnover» catalytique pouvant atteindre 2000 dans le cas de m-cresol. Nous croyons que ces réactions d’alcoolyse procèdent par activation hétérolytique de l’alcool par l’espèce dimérique via des liaisons hydrogènes avec une ou deux des fonctions amides du dimère. Les espèces dimériques de Ni (II) s’oxydent facilement électrochimiquement et par reaction avec NBS ou Br2. De façon surprenante, l’oxydation chimique mène à l’isolation de nouveaux produits monomériques dans lesquels le centre métallique et le ligand sont oxydés. Le mécanisme d’oxydation fut aussi investigué par RMN, «UV-vis-NIR», «DFT» et spectroélectrochimie.

Cage de résonance à base de films minces transparents et conducteurs de nanotubes de carbone

Mémoire numérisé par la Division de la gestion de documents et des archives de l'Université de Montréal

Polymères de coordination et éponge cristalline : de nouveaux matériaux pour la conversion de l’énergie solaire et la résolution de la structure cristalline de composés huileux.

Le premier volet de ce travail portera sur l’expérience acquise lors d’un stage d’étude à Tokyo, au Japon, dans le groupe de recherche du Pr. Makoto Fujita, une sommité d’envergure internationale dans le domaine de l’auto-assemblage. En continuité avec les plus récents travaux du Pr. Fujita, des systèmes poreux auto-assemblés présentant des cavités fonctionnalisées ont été développés dans le but d’encapsuler des acides gras afin d’en déterminer la structure cristalline. Ces éponges ont été caractérisées par des techniques courantes telles que la spectroscopie à résonance magnétique nucléaire 1H, 13C{1H} et Cosy, la spectrométrie de masse, l’analyse élémentaire, la microscopie optique infrarouge ainsi que la diffraction des rayons X. Une autre approche employée pour obtenir de meilleures propriétés spectroscopiques fut la synthèse de dendrimères métalliques de génération 0. Un nouveau ligand de type 1,3,5-triazine a été synthétisé par une réaction typique de cyclisation de nitrile en présence catalytique d’hydrure de sodium. Des espèces mono-, bis- et trinucléaire de Ru(II) furent synthétisés ainsi que deux espèces hétérométalliques de Ru(II)/Pt(II) et de Ru(II)/Os(II). Tous les complexes obtenus furent caractérisés par spectroscopie à résonance magnétique nucléaire (1H, 13C{1H} et Cosy) à l’état liquide, par spectroscopie de masse à haute résolution et par analyse élémentaire. La génération de dihydrogène à partir de l’espèce hétérométallique a été étudiée. Les propriétés optiques et électroniques ont été analysées par spectroscopie UV-Vis, par analyse de la luminescence, du temps de vie de luminescence, par des analyses de rendement quantique ainsi que par des analyses de voltampérométrie cyclique à balayage. Finalement, dans le but d’améliorer les propriétés spectroscopiques d’absorption de complexes métalliques, nous avons synthétisé une série de polymères homo- et hétérométalliques, intégrant des ligands de type bis(2,2’:6,2’’-terpyridine). Les complexes générés furent caractérisés par diverses techniques tel que la spectroscopie à résonance magnétique nucléaire (1H, 13C{1H} et Cosy) à l’état liquide, par spectroscopie de masse à haute résolution ainsi que par analyse élémentaire. Les propriétés optiques et électroniques ont été analysées par spectroscopie UV-Vis, par analyse de la luminescence, du temps de vie de luminescence, par des analyses de rendement quantique ainsi que par des analyses de voltampérométrie cyclique à balayage.

Preparation and characterisation of certain II-VI, I-III-VI2 semiconductor thin films and transparent conducting oxides

There is an increasing demand for renewable energies due to the limited availability of fossil and nuclear fuels and due to growing environmental problems. Photovoltaic (PV) energy conversion has the potential to contribute significantly to the electrical energy generation in the future. Currently, the cost for photovoltaic systems is one of the main obstacles preventing production and application on a large scale. The photovoltaic research is now focused on the development of materials that will allow mass production without compromising on the conversion efficiencies. Among important selection criteria of PV material and in particular for thin films, are a suitable band gap, high absorption coefficient and reproducible deposition processes capable of large-volume and low cost production. The chalcopyrite semiconductor thin films such as Copper indium selenide and Copper indium sulphide are the materials that are being intensively investigated for lowering the cost of solar cells. Conversion efficiencies of 19 % have been reported for laboratory scale solar cell based on CuInSe2 and its alloys. The main objective of this thesis work is to optimise the growth conditions of materials suitable for the fabrication of solar cell, employing cost effective techniques. A typical heterojunction thin film solar cell consists of an absorber layer, buffer layer and transparent conducting contacts. The most appropriate techniques have been used for depositing these different layers, viz; chemical bath deposition for the window layer, flash evaporation and two-stage process for the absorber layer, and RF magnetron sputtering for the transparent conducting layer. Low cost experimental setups were fabricated for selenisation and sulphurisation experiments, and the magnetron gun for the RF sputtering was indigenously fabricated. The films thus grown were characterised using different tools. A powder X-ray diffractometer was used to analyse the crystalline nature of the films. The energy dispersive X-ray analysis (EDX) and scanning electron microscopy i (SEM) were used for evaluating the composition and morphology of the films. Optical properties were investigated using the UV-Vis-NIR spectrophotometer by recording the transmission/absorption spectra. The electrical properties were studied using the two probe and four probe electrical measurements. Nature of conductivity of the films was determined by thermoprobe and thermopower measurements. The deposition conditions and the process parameters were optimised based on these characterisations.

Photophysical and Electrochemical Investigations on Photoconducting Poly(6-tert-butyl-3,4-dihydro-2H- 1,3-benzoxazine)

Poly(6-tert-butyl-3,4-dihydro-2H-1,3-benzoxazine) was synthesized by thermally activated cationic ring opening polymerization. The structure of the polymer was confirmed by spectral and thermal studies. The highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) were estimated using cyclic voltammetry and optical absorption. Modulated photocurrent measurement technique was employed to study the spectral and field dependence of photocurrent. Photocurrent of the order of 1.5 micro A/m2 was obtained for polymer at a biasing electric field of 40 V/mico m.

Photothermal and photoacoustic investigations on certain polymers and semi conducting materials

Material synthesizing and characterization has been one of the major areas of scientific research for the past few decades. Various techniques have been suggested for the preparation and characterization of thin films and bulk samples according to the industrial and scientific applications. Material characterization implies the determination of the electrical, magnetic, optical or thermal properties of the material under study. Though it is possible to study all these properties of a material, we concentrate on the thermal and optical properties of certain polymers. The thermal properties are detennined using photothermal beam deflection technique and the optical properties are obtained from various spectroscopic analyses. In addition, thermal properties of a class of semiconducting compounds, copper delafossites, arc determined by photoacoustic technique.Photothermal technique is one of the most powerful tools for non-destructive characterization of materials. This forms a broad class of technique, which includes laser calorimetry, pyroelectric technique, photoacollstics, photothermal radiometric technique, photothermal beam deflection technique etc. However, the choice of a suitable technique depends upon the nature of sample and its environment, purpose of measurement, nature of light source used etc. The polynler samples under the present investigation are thermally thin and optically transparent at the excitation (pump beam) wavelength. Photothermal beam deflection technique is advantageous in that it can be used for the detennination of thermal diffusivity of samples irrespective of them being thermally thick or thennally thin and optically opaque or optically transparent. Hence of all the abovementioned techniques, photothemlal beam deflection technique is employed for the successful determination of thermal diffusivity of these polymer samples. However, the semi conducting samples studied are themlally thick and optically opaque and therefore, a much simpler photoacoustic technique is used for the thermal characterization.The production of polymer thin film samples has gained considerable attention for the past few years. Different techniques like plasma polymerization, electron bombardment, ultra violet irradiation and thermal evaporation can be used for the preparation of polymer thin films from their respective monomers. Among these, plasma polymerization or glow discharge polymerization has been widely lIsed for polymer thin fi Im preparation. At the earlier stages of the discovery, the plasma polymerization technique was not treated as a standard method for preparation of polymers. This method gained importance only when they were used to make special coatings on metals and began to be recognized as a technique for synthesizing polymers. Thc well-recognized concept of conventional polymerization is based on molecular processcs by which thc size of the molecule increases and rearrangemcnt of atoms within a molecule seldom occurs. However, polymer formation in plasma is recognized as an atomic process in contrast to the above molecular process. These films are pinhole free, highly branched and cross linked, heat resistant, exceptionally dielectric etc. The optical properties like the direct and indirect bandgaps, refractive indices etc of certain plasma polymerized thin films prepared are determined from the UV -VIS-NIR absorption and transmission spectra. The possible linkage in the formation of the polymers is suggested by comparing the FTIR spectra of the monomer and the polymer. The thermal diffusivity has been measured using the photothermal beam deflection technique as stated earlier. This technique measures the refractive index gradient established in the sample surface and in the adjacent coupling medium, by passing another optical beam (probe beam) through this region and hence the name probe beam deflection. The deflection is detected using a position sensitive detector and its output is fed to a lock-in-amplifIer from which the amplitude and phase of the deflection can be directly obtained. The amplitude and phase of the deflection signal is suitably analyzed for determining the thermal diffusivity.Another class of compounds under the present investigation is copper delafossites. These samples in the form of pellets are thermally thick and optically opaque. Thermal diffusivity of such semiconductors is investigated using the photoacoustic technique, which measures the pressure change using an elcctret microphone. The output of the microphone is fed to a lock-in-amplificr to obtain the amplitude and phase from which the thermal properties are obtained. The variation in thermal diffusivity with composition is studied.

Spectral studies of naphthalocyanine (Nc) and rare earth phthalocyanine (RePc) molecules in an inorganic glassy borate matrix

Optical absorption and emission spectral studies of free and metal naphthalocyanine doped borate glass matrix are reported for the first time. Absorption spectra recorded in the UV- VIS-NIR region show the characteristic absorption bands, namely, the B-band and Q-band of the naphthalocyanine (Nc) molecule. Some of the important spectral parameters, namely, the optical absorption coefficient (α), molar extinction coefficient (ε) and absorption cross section (σa) of the principal absorption transitions are determined. Optical band gap (Eg) of the materials evaluated from the functional dependence of absorption coefficient on photon energy lies in the range 1.6 eV≤Eg≤2.1 eV. All fluorescence spectra except that of EuNc consist of an intense band in the 765 nm region corresponding to the excitation of Q-band. In EuNc the maximum fluorescence intensity band is observed at 824 nm. The intensity of the principal fluorescence band is maximum in ZnNc, whereas it is minimum in H2Nc. Radiative parameters of the principal fluorescence transitions corresponding to the Q-band excitation are also reported for the naphthalocyanine and phthalocyanine based matrices.

Studies on Catalysis by Nano Titania Modified with Metals and Nonmetals

Semiconductor photocatalysis has received much attention during last three decades as a promising solution for both energy generation and environmental problems. Heterogeneous photocatalytic oxidation allows the degradation of organic compounds into carbon dioxide and water in the presence of a semiconductor catalyst and UV light source. The •OH radicals formed during the photocatalytic processes are powerful oxidizing agents and can mineralise a number of organic contaminants. Titanium dioxide (TiO2), due to its chemical stability, non-toxicity and low cost represents one of the most efficient photocatalyst. However, only the ultraviolet fraction of the solar radiation is active in the photoexcitation processes using pure TiO2 and although, TiO2 can treat a wide range of organic pollutants the effectiveness of the process for pollution abatement is still low. A more effective and efficient catalyst therefore must be formulated. Doping of TiO2 was considered with the aim of improving photocatalytic properties. In this study TiO2 catalyst was prepared using the sol-gel method. Metal and nonmetal doped TiO2 catalysts were prepared. The photoactivity of the catalyst was evaluated by the photodegradation of different dyes and pesticides in aqueous solution. High photocatalytic degradation of all the pollutants was observed with doped TiO2. Structural and optical properties of the catalysts were characterized using XRD, BET surface area, UV-Vis. DRS, CHNS analysis, SEM, EDX, TEM, XPS, FTIR and TG. All the catalysts showed the anatase phase. The presence of dopants shifts the absorption of TiO2 into the visible region indicating the possibility of using visible light for photocatalytic processes.

Synthesis, Characterization and Applications of Modified TiO2 Systems

This thesis is divided in to 9 chapters and deals with the modification of TiO2 for various applications include photocatalysis, thermal reaction, photovoltaics and non-linear optics. Chapter 1 involves a brief introduction of the topic of study. An introduction to the applications of modified titania systems in various fields are discussed concisely. Scope and objectives of the present work are also discussed in this chapter. Chapter 2 explains the strategy adopted for the synthesis of metal, nonmetal co-doped TiO2 systems. Hydrothermal technique was employed for the preparation of the co-doped TiO2 system, where Ti[OCH(CH3)2]4, urea and metal nitrates were used as the sources for TiO2, N and metals respectively. In all the co-doped systems, urea to Ti[OCH(CH3)2]4 was taken in a 1:1 molar ratio and varied the concentration of metals. Five different co-doped catalytic systems and for each catalysts, three versions were prepared by varying the concentration of metals. A brief explanation of physico-chemical techniques used for the characterization of the material was also presented in this chapter. This includes X-ray Diffraction (XRD), Raman Spectroscopy, FTIR analysis, Thermo Gravimetric Analysis, Energy Dispersive X-ray Analysis (EDX), Scanning Electron Microscopy(SEM), UV-Visible Diffuse Reflectance Spectroscopy (UV-Vis DRS), Transmission Electron Microscopy (TEM), BET Surface Area Measurements and X-ray Photoelectron Spectroscopy (XPS). Chapter 3 contains the results and discussion of characterization techniques used for analyzing the prepared systems. Characterization is an inevitable part of materials research. Determination of physico-chemical properties of the prepared materials using suitable characterization techniques is very crucial to find its exact field of application. It is clear from the XRD pattern that photocatalytically active anatase phase dominates in the calcined samples with peaks at 2θ values around 25.4°, 38°, 48.1°, 55.2° and 62.7° corresponding to (101), (004), (200), (211) and (204) crystal planes (JCPDS 21-1272) respectively. But in the case of Pr-N-Ti sample, a new peak was observed at 2θ = 30.8° corresponding to the (121) plane of the polymorph brookite. There are no visible peaks corresponding to dopants, which may be due to their low concentration or it is an indication of the better dispersion of impurities in the TiO2. Crystallite size of the sample was calculated from Scherrer equation byusing full width at half maximum (FWHM) of the (101) peak of the anatase phase. Crystallite size of all the co-doped TiO2 was found to be lower than that of bare TiO2 which indicates that the doping of metal ions having higher ionic radius into the lattice of TiO2 causes some lattice distortion which suppress the growth of TiO2 nanoparticles. The structural identity of the prepared system obtained from XRD pattern is further confirmed by Raman spectra measurements. Anatase has six Raman active modes. Band gap of the co-doped system was calculated using Kubelka-Munk equation and that was found to be lower than pure TiO2. Stability of the prepared systems was understood from thermo gravimetric analysis. FT-IR was performed to understand the functional groups as well as to study the surface changes occurred during modification. EDX was used to determine the impurities present in the system. The EDX spectra of all the co-doped samples show signals directly related to the dopants. Spectra of all the co-doped systems contain O and Ti as the main components with low concentrations of doped elements. Morphologies of the prepared systems were obtained from SEM and TEM analysis. Average particle size of the systems was drawn from histogram data. Electronic structures of the samples were identified perfectly from XPS measurements. Chapter 4 describes the photocatalytic degradation of herbicides Atrazine and Metolachlor using metal, non-metal co-doped titania systems. The percentage of degradation was analyzed by HPLC technique. Parameters such as effect of different catalysts, effect of time, effect of catalysts amount and reusability studies were discussed. Chapter 5 deals with the photo-oxidation of some anthracene derivatives by co-doped catalytic systems. These anthracene derivatives come underthe category of polycyclic aromatic hydrocarbons (PAH). Due to the presence of stable benzene rings, most of the PAH show strong inhibition towards biological degradation and the common methods employed for their removal. According to environmental protection agency, most of the PAH are highly toxic in nature. TiO2 photochemistry has been extensively investigated as a method for the catalytic conversion of such organic compounds, highlighting the potential of thereof in the green chemistry. There are actually two methods for the removal of pollutants from the ecosystem. Complete mineralization is the one way to remove pollutants. Conversion of toxic compounds to another compound having toxicity less than the initial starting compound is the second way. Here in this chapter, we are concentrating on the second aspect. The catalysts used were Gd(1wt%)-N-Ti, Pd(1wt%)-N-Ti and Ag(1wt%)-N-Ti. Here we were very successfully converted all the PAH to anthraquinone, a compound having diverse applications in industrial as well as medical fields. Substitution of 10th position of desired PAH by phenyl ring reduces the feasibility of photo reaction and produced 9-hydroxy 9-phenyl anthrone (9H9PA) as an intermediate species. The products were separated and purified by column chromatography using 70:30 hexane/DCM mixtures as the mobile phase and the resultant products were characterized thoroughly by 1H NMR, IR spectroscopy and GCMS analysis. Chapter 6 elucidates the heterogeneous Suzuki coupling reaction by Cu/Pd bimetallic supported on TiO2. Sol-Gel followed by impregnation method was adopted for the synthesis of Cu/Pd-TiO2. The prepared system was characterized by XRD, TG-DTG, SEM, EDX, BET Surface area and XPS. The product was separated and purified by column chromatography using hexane as the mobile phase. Maximum isolated yield of biphenyl of around72% was obtained in DMF using Cu(2wt%)-Pd(4wt%)-Ti as the catalyst. In this reaction, effective solvent, base and catalyst were found to be DMF, K2CO3 and Cu(2wt%)-Pd(4wt%)-Ti respectively. Chapter 7 gives an idea about the photovoltaic (PV) applications of TiO2 based thin films. Due to energy crisis, the whole world is looking for a new sustainable energy source. Harnessing solar energy is one of the most promising ways to tackle this issue. The present dominant photovoltaic (PV) technologies are based on inorganic materials. But the high material, low power conversion efficiency and manufacturing cost limits its popularization. A lot of research has been conducted towards the development of low-cost PV technologies, of which organic photovoltaic (OPV) devices are one of the promising. Here two TiO2 thin films having different thickness were prepared by spin coating technique. The prepared films were characterized by XRD, AFM and conductivity measurements. The thickness of the films was measured by Stylus Profiler. This chapter mainly concentrated on the fabrication of an inverted hetero junction solar cell using conducting polymer MEH-PPV as photo active layer. Here TiO2 was used as the electron transport layer. Thin films of MEH-PPV were also prepared using spin coating technique. Two fullerene derivatives such as PCBM and ICBA were introduced into the device in order to improve the power conversion efficiency. Effective charge transfer between the conducting polymer and ICBA were understood from fluorescence quenching studies. The fabricated Inverted hetero junction exhibited maximum power conversion efficiency of 0.22% with ICBA as the acceptor molecule. Chapter 8 narrates the third order order nonlinear optical properties of bare and noble metal modified TiO2 thin films. Thin films were fabricatedby spray pyrolysis technique. Sol-Gel derived Ti[OCH(CH3)2]4 in CH3CH2OH/CH3COOH was used as the precursor for TiO2. The precursors used for Au, Ag and Pd were the aqueous solutions of HAuCl4, AgNO3 and Pd(NO3)2 respectively. The prepared films were characterized by XRD, SEM and EDX. The nonlinear optical properties of the prepared materials were investigated by Z-Scan technique comprising of Nd-YAG laser (532 nm,7 ns and10 Hz). The non-linear coefficients were obtained by fitting the experimental Z-Scan plot with the theoretical plots. Nonlinear absorption is a phenomenon defined as a nonlinear change (increase or decrease) in absorption with increasing of intensity. This can be mainly divided into two types: saturable absorption (SA) and reverse saturable absorption (RSA). Depending on the pump intensity and on the absorption cross- section at the excitation wavelength, most molecules show non- linear absorption. With increasing intensity, if the excited states show saturation owing to their long lifetimes, the transmission will show SA characteristics. Here absorption decreases with increase of intensity. If, however, the excited state has strong absorption compared with that of the ground state, the transmission will show RSA characteristics. Here in our work most of the materials show SA behavior and some materials exhibited RSA behavior. Both these properties purely depend on the nature of the materials and alignment of energy states within them. Both these SA and RSA have got immense applications in electronic devices. The important results obtained from various studies are presented in chapter 9.

Dye-sensitized solar cells based on perylene derivatives

The oil price rises more and more, and the world energy consumption is projected to expand by 50 percent from 2005 to 2030. Nowadays intensive research is focused on the development of alternative energies. Among them, there are dye-sensitized nanocrystalline solar cells (DSSCs) “the third generation solar cells”. The latter have gained attention during the last decade and are currently subject of intense research in the framework of renewable energies as a low-cost photovoltaic. At present DSSCs with ruthenium based dyes exhibit highest efficiencies (ca 11%). The objective of the present work is to fabricate, characterize and improve the performance of DSSCs based on metal free dyes as sensitizers, especially on perylene derivatives. The work begins by a general introduction to the photovoltaics and dye-sensitized solar cells, such as the operating principles and the characteristics of the DSSCs. Chapter 2 and 3 discuss the state of the art of sensitizers used in DSSCs, present the compounds used as sensitizer in the present work and illustrate practical issues of experimental techniques and device preparation. A comparative study of electrolyte-DSSCs based on P1, P4, P7, P8, P9, and P10 are presented in chapter 4. Experimental results show that the dye structure plays a crucial role in the performance of the devices. The dye based on the spiro-concept (bipolar spiro compound) exhibited a higher efficiency than the non-spiro compounds. The presence of tert-butylpyridine as additive in the electrolyte was found to increase the open circuit voltage and simultaneously decrease the efficiency. The presence of lithium ions in the electrolyte increases both output current and the efficiency. The sensitivity of the dye to cations contained in the electrolyte was investigated in the chapter 5. FT-IR and UV-Vis were used to investigate the in-situ coordination of the cation to the adsorbed dye in the working devices. The open-circuit voltage was found to depend on the number of coordination sites in the dye. P1 with most coordination sites has shown the lowest potential drop, opposite to P7, which is less sensitive to cations in the working cells. A strategy to improve the dye adsorption onto the TiO2 surface, and thus the light harvesting efficiency of the photoanode by UV treatment, is presented in chapter 6. The treatment of the TiO2 film with UV light generates hydroxyl groups and renders the TiO2 surface more and more hydrophilic. The treated TiO2 surface reacts readily with the acid anhydride group of the dye that acts as an anchoring group and improves the dye adsorption. The short-circuit current density and the efficiency of the electrolyte-based dye cells was considerably improved by the UV treatment of the TiO2 film. Solid-state dye-sensitized solar cells (SSDs) based on spiro-MeOTAD (used as hole transport material) are studied in chapter 7. The efficiency of SSDs was globally found to be lower than that of electrolyte-based solar cells. That was due to poor pore filling of the dye-loaded TiO2 film by the spin-coated spiro-MeOTAD and to the significantly slower charge transport in the spiro-MeOTAD compared to the electrolyte redox mediator. However, the presence of the donor moieties in P1 that are structurally similar to spiro-MeOTAD was found to improve the wettability of the P1-loaded TiO2 film. As a consequence the performance of the P1-based solid-state cells is better compared to the cells based on non-spiro compounds.

Synthesis and characterization of thermally stable second-order nonlinear optical side-chain polyimides containing thiazole and benzothiazole push-pull chromophores

Push-pull nonlinear optical (NLO) chromophores containing thiazole and benzothiazole acceptors were synthesized and characterized. Using these chromophores a series of second-order NLO polyimides were Successfully prepared from 4,4'-(hexafluoroisopropylidene) diphthalic anhydride (6FDA), pyromellitic dianhydride (PMDA) and 3,3'4,4'-benzophenone tetracarboxylic dianhydride (BTDA) by a standard condensation polymerization technique. These polyimides exhibit high glass transition temperatures ranging from 160 to 188 degrees C. UV-vis spectrum of polyimide exhibited a slight blue shift and decreases in absorption due to birefringence. From the order parameters, it was found that chromophores were aligned effectively. Using in situ poling and temperature ramping technique, the optical temperatures for corona poling were obtained. It was found that the optimal temperatures of polyimides approach their glass transition temperatures. These polyimides demonstrate relatively large d(33) values range between 35.15 and 45.20 pm/V at 532 nm. (C) 2008 Elsevier B.V. All rights reserved.

Analysis of red and yellow ochre samples from Clearwell Caves and Catalhoyuk by vibrational spectroscopy and other techniques

Ochre samples excavated from the neolithic site at Qatalhoyuk, Turkey have been compared with "native" ochres from Clearwell Caves, UK using infrared spectroscopy backed up by Raman spectroscopy, scanning electron microscopy (with energy-dispersive X-rays (EDX) analysis), powder X-ray diffraction, diffuse reflection UV-Vis and atomic absorption spectroscopies. For the Clearwell Caves ochres, which range in colour from yellow-orange to red-brown, it is shown that the colour is related to the nature of the chromophore present and not to any differences in particle size. The darker red ochres contain predominantly haematite while the yellow ochre contains only goethite. The ochres from Qatalhoyuk contain only about one-twentieth of the levels of iron found in the Clearwell Caves ochres. The iron oxide pigment (haematite in all cases studied here) has been mixed with a soft lime plaster which also contains calcite and silicate (clay) minerals. (C) 2003 Elsevier B.V. All rights reserved.