Reprodução de Meloidogyne javanica em olerícolas e em plantas utilizadas na adubação verde

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Estudo das propriedades físico-químicas do biodiesel e suas influências na deterioração dos elastômeros aplicados no sistema de injeção dos motores diesel

The biodiesel use has become important due to its renewable character and to reduce environmental impacts during the fuel burning. Theses benefit will be valid if the fuel shows good performance, chemistry stability and compatibility with engines. Biodiesel is a good fuel to diesel engines due to its lubricity. Then, the aimed of this study was to verify the physicalchemistry properties of biodiesel and their correlations with possible elastomers damage after biodiesel be used as fuel in an injection system. The methodology was divided in three steps: biodiesels synthesis by transesterification of three vegetable oil (soybean, palm and sunflower) and their physical-chemistry characterization (viscosity, oxidative stability, flash point, acidity, humidity and density); pressurized test of compatibility between elastomers (NBR and VITON) and biodiesel, and the last one, analyze of biodiesels lubricity by tribological test ball-plan( HFRR). Also, the effect of mixture of biodiesel and diesel in different concentrations was evaluated. The results showed that VITON showed better compatibility with all biodiesel blends in relation to NBR, however when VITON had contact with sunflower biodiesel and its blends the swelling degree suffer higher influences due to biodiesel humidity. For others biodiesels and theirs blends, this elastomer kept its mechanical properties constant. The better tribological performance was observed for blends with high biodiesel concentration, lower friction coefficient was obtained when palm biodiesel was used. The main mechanisms observed during the HFRR tests were abrasive and oxidative wear

Estudo tribológico de biolubrificantes com adição de nanopartículas de óxidos (zinco e cobre)

Currently, vegetable oils have been studied for bio-lubricants base that fits the new environmental standards. Since, in a world full of finite natural resources, mineral oils bring consequences to the environment due to its low biodegradability and toxicity, also it is important to consider that synthetic oils have a high cost The aim of this work is to obtain a biolubricant additived with oxide nanoparticles (ZnO and CuO) for better resistance to friction and wear, which is not toxic to the environment and have better adherence under boundary lubrication. The methodology consisted in the synthesis of bio-lubricants (soybean and sunflower base) by epoxidation reaction. Then, some physical-chemical analysis in bio-lubricants are made to characterize theses lubricants, such as, density, acidity, iodine value, viscosity, viscosity index. Later, the lubricants were additive with nanoparticles. The tribological performance was evaluated by the equipment HFRR (High Frequency Reciprocating Rig) consisting of a wear test ball-plan type. The characterization of wear analysis was performed by SEM / EDS. The results show that bio-lubricants may be synthesized by reaction of epoxidation with good conversion. Tribological point of view, the epoxidized oils are more effective than lubricant additived with the oxide nanoparticles, they had lower coefficients of friction and better rate of film formation in the study. However, because they are environmentally friendly, bio-lubricants gain the relevant importance in tribological field

Remoção de óleo da água de produção por flotação em coluna utilizando tensoativos de origem vegetal

In the petroleum industry, water is always present in the reservoir formation together with petroleum and natural gas and this fact provokes the production of water with petroleum, resulting in a great environmental impact. Several methods can be applied for treatment of oily waters, such as: gravitational vases, granulated media filtration systems, flotation process, centrifugation process and the use of hydrocyclones, which can also be used in a combined way. However, the flotation process has showed a great efficiency as compared with other methods, because these methods do not remove great part of the emulsified oil. In this work was investigated the use of surfactants derived from vegetable oils, OSS and OGS, as collectors, using the flotation process in a glass column with a porous plate filter in its base for the input of the gaseous steam. For this purpose, oil/water emulsions were prepared using mechanical stirring, with concentrations around 300 ppm. The air flow rate was set at 700 cm3/min and the porous plate filter used for the generation of the air bubbles has pore size varying from 16 to 40 Pm. The column operated at constant volume (1500mL). A new methodology has been developed to collect the samples, where, instead of collecting the water phase, it was collected the oil phase removed by the process in the top of the flotation column. It has been observed that it is necessary to find an optimum surfactant concentration to achieve enhanced removal efficiency. Being for OSS 1.275 mmol/L and for OGS 0.840 mmol/L, with removal efficiencies of 93% and 99%, respectively, using synthetic solutions. For the produced water, the removal in these concentrations was 75% for OSS and 65% for OGS. It is possible to remove oil from water in a flotation process using surfactants of high HLB, fact that is against the own definition of HLB (Hydrophile-Lipophile Balance). The interfacial tension is an important factor in the oil removal process using a flotation process, because it has direct interference in the coalescence of the oil drops. The spreading of the oil of the air bubble should be considered in the process, and for the optimum surfactant concentrations it reached a maximum value. The removal kinetics for the flotation process using surfactants in the optimum concentration has been adjusted according to a first order model, for synthetic water as for the produced water.

Estabilidade de agregados do solo após manejo com rotações de culturas e escarificação

O objetivo desse trabalho foi avaliar, em solo compactado, a estabilidade dos agregados influenciada pelo cultivo de espécies de cobertura em esquema de rotações de culturas, em sistema de semeadura direta, mediante o efeito da escarificação mecânica. As rotações de culturas repetidas por três anos consecutivos envolveram o cultivo de triticale e girassol, no outono-inverno, associados ao cultivo de milheto, de sorgo forrageiro e de Crotalária júncea como plantas de cobertura, antecedendo o da soja (cultura de verão). No tratamento envolvendo a escarificação mecânica, a área permaneceu em pousio entre os cultivos de outono-inverno e de verão. O experimento foi realizado na Fazenda Experimental Lageado (Botucatu-SP), nos anos agrícolas de 2003/2004, 2004/2005 e 2005/2006. O delineamento experimental foi o de blocos ao acaso, com quatro repetições, em esquema de parcelas subdivididas. As amostras para a análise da estabilidade de agregados foram coletadas nas profundidades de 0 a 0,05 m e de 0,05 a 0,10 m após o manejo das plantas de cobertura em dezembro de 2003 e de 2005. Logo no primeiro ano de instalação do experimento, o cultivo de triticale resultou em maior porcentagem de agregados com mais de 2 mm, maior DMG e maior DMP na camada de 0 a 5 cm, além de maior DMP na camada de 0,05 a 0,10 m. Já a escarificação do solo e a ausência do cultivo de plantas de cobertura proporcionaram menor porcentagem de agregados maiores que 2 mm e menor DMP na camada de 0,05 a 0,10 m. A estabilidade dos agregados foi influenciada pela rotação de culturas, sendo maior na camada de 0 a 0,05 m e de 0,05 a 0,10 m quando o triticale foi introduzido como espécie de outono-inverno.

Remoção conjugada de metais e óleo de água produzida

Petroleum can be associated or not with natural gas, but in both cases water is always present in its formation. The presence of water causes several problems, such as the difficulty of removing the petroleum from the reservoir rock and the formation of waterin-oil and oil-in-water emulsions. The produced water causes environmental problems, which should be solved to reduce the effect of petroleum industry in the environment. The main objective of this work is to remove simultaneously from the produced water the dispersed petroleum and dissolved metals. The process is made possible through the use of anionic surfactants that with its hydrophilic heads interacts with ionized metals and with its lipophilic tails interacts with the oil. The studied metals were: calcium, magnesium, barium, and cadmium. The surfactants used in this research were derived from: soy oil, sunflower oil, coconut oil, and a soap obtained from a mixture of 5wt.% coconut oil and 95wt.% animal fat. It was used a sample of produced water from Terminal de São Sebastião, São Paulo. As the concentration of the studied metals in produced water presented values close to 300 mg/L, it was decided to use this concentration as reference for the development of this research. Molecular absorption and atomic absorption spectroscopy were used to determine petroleum and metals concentrations in the water sample, respectively. A constant pressure filtration system was used to promote the separation of solid and liquid phases. To represent the behavior of the studied systems it was developed an equilibrium model and a mathematical one. The obtained results showed that all used surfactants presented similar behavior with relation to metals extraction, being selected the surfactant derived from soy oil for this purpose. The values of the partition coefficients between the solid and liquid phases " D " for the studied metals varied from 0.2 to 1.1, while the coefficients for equilibrium model " K " varied from 0.0002 and 0.0009. The removal percentile for oil with all metals associated was near 100%, showing the efficiency of the process

Remoção do cobre de efluente galvânico aplicando tensoativos derivado de óleos vegetais

Copper is one of the most used metals in platingprocesses of galvanic industries. The presence of copper, a heavy metal, in galvanic effluents is harmful to the environment.The main objective of this researchwas the removal ofcopperfromgalvanic effluents, using for this purpose anionic surfactants. The removal process is based on the interaction between the polar head group of the anionic surfactant and the divalent copper in solution. The surfactants used in this study were derived from soybean oil (OSS), coconut oil (OCS), and sunflower oil (OGS). It was used a copper synthetic solution (280 ppm Cu+2) simulating the rinse water from a copper acid bath of a galvanic industry. It were developed 23and 32 factorial designs to evaluate the parameters that have influence in theremoval process. For each surfactant (OSS, OCS, and OGS), the independent variables evaluated were: surfactant concentration (1.25 to 3.75 g/L), pH (5 to 9) and the presence of an anionic polymer (0 to 0.0125 g/L).From the results obtained in the 23 factorial design and in the calculus for estimatingthe stoichiometric relationship between surfactants and copper in solution, it were developed new experimental tests, varying surfactant concentration in the range of 1.25 to 6.8 g/L (32 factorial design).The results obtained in the experimental designs were subjected to statistical evaluations to obtain Pareto charts and mathematical modelsfor Copper removal efficiency (%). The statistical evaluation of the 23 and 32factorial designs, using saponifiedcoconut oil (OCS), presented the mathematical model that best described the copper removal process.It can be concluded that OCS was the most efficient anionic surfactant, removing 100% of the copper present in the synthetic galvanic solution

Tratamento de água de produção de petróleo visando o aproveitamento na obtenção de barrilha

The petroleum production is associated to the produced water, which has dispersed and dissolved materials that damage not only the environment, but also the petroleum processing units. This study aims at the treatment of produced water focusing mainly on the removal of metals and oil and using this treated water as raw material for the production of sodium carbonate. Initially, it was addressed the removal of the following divalent metals: calcium, magnesium, barium, zinc, copper, iron, and cadmium. For this purpose, surfactants derived from vegetable oils, such as coconut oil, soybean oil, and sunflower oil, were used. The investigation showed that there is a stoichiometric relationship between the metals removed from the produced water and the surfactants used in the process of metals removal. It was also developed a model that correlates the hydrolysis constant of saponified coconut oil with the metal distribution between the resulting stages of the proposed process, flocs and aqueous phases, and relating the results with the pH of the medium. The correlation coefficient obtained was 0.963. Next, the process of producing washing soda (prefiro soda ahs ou sodium carbonate) started. The resulting water from the various treatment approaches from petroleum production water was used. During this stage of the research, it was observed that the surfactant assisted in the produced water treatment, by removing some metals and the dispersed oil entirety. The yield of sodium carbonate production was approximately 80%, and its purity was around 95%. It was also assessed, in the production of sodium carbonate, the influence of the type of reactor, using a continuous reactor and a batch reactor. These tests showed that the process with continuous reactor was not as efficient as the batch process. In general, it can be concluded that the production of sodium carbonate from water of oil production is a feasible process, rendering an effluent that causes a great environmental impact a raw material with large scale industrial use

Aprendizado espacial-temporal em um ambiente complexo sem restrição alimentar em ratos

Timeplace learning is the capacity of organisms to associate both space and time with a biological relevant stimulus such as food. Experiments are usually done with food restricted animals due to the belief that food system activation is necessary for timeplace learning. Another line of thought suggest that, in addition to food system activation, response cost should be increased to effectively allow timeplace discrimination. The purpose of this experiment was to test whether a complex environment, which presumably implied in a heightened response cost, would facilitate timeplace association in satiated rats using a highly palatable food as reward. Nine rats were trained in a timeplace task for 30 nonconsecutive days. A large experimental box (1x1m) divided in four compartments was used. To access each compartment the animal had to overcome a series of obstacles such as ramps, staircases and mazes. Two feeders localized in opposite compartments were rewarded with sunflower seeds in two daily sessions. One feeder offered the reward during the morning sessions while the second feeder in afternoon sessions. After the 15th day of training, the animals began to show a preference for the correct feeder during the correct time of day expressed by increased frequency of visits as well as lower latency to access the feeders. These results suggest that satiated animals are also capable of learning a timespace task as far as the experimental context is complex enough to result in a higher response cost

Hidróxidos duplos lamelares aplicados à obtenção de biodiesel

In this paper, the Layered Double Hydroxides (LDH s) type hydrotalcite were synthesized, characterized and tested as basic heterogeneous catalysts for the production of biodiesel by transesterification of sunflower oil with methanol. The synthesis of materials Layered Double Hydroxides (LDH s) by co-precipitation method from nitrates of magnesium and aluminum, and sodium carbonate. The materials were submitted to the variation in chemical composition, which is the amount of Mg2+ ions replaced by Al3+. This variation affects the characteristic physico-chemical and reaction the solid. The molar ratio varied in the range of 1:1 and 3:1 magnesium / aluminum, and their values between 0.2 and 0.33. This study aims to evaluate the influence of variation of molar ratio of mixed oxides derived from LDH s and the influence of impregnation of a material with catalytic activity, the KI, the rate of conversion of sunflower oil into methyl esters (biodiesel) through transesterification by heterogeneous catalysis. .The catalysts were calcined at 550 ° C and characterized by X-ray diffraction (XRD), scanning electron microscopy and energy dispersive spectroscopy of X-ray (SEM / EDS), thermogravimetric analysis (TG) and test basicity. The transesterification reaction was performed for reflux is a mixture of sunflower oil and methanol with a molar ratio of 15:1, a reaction time of 4h and a catalyst concentration of 2% by weight. The physical-chemical characterization of sunflower oil and biodiesel obtained by the route methyl submitted according NBR, EN, ASTM. Subsequently, it was with the chromatographic and thermogravimetric characterizations of oils. The results of chromatographic analysis showed that the catalysts were effective in converting vegetable oil into biodiesel, in particular the type hydrotalcite KI-HDL-R1, with a conversion of 99.2%, indicating the strong influence of the chemical composition of the material, in special due to presence of potassium in the structure of the catalyst

Síntese e caracterização de óxidos de zinco e de magnésio suportados em A1SBA-15 para produção de biodiesel

To overcome the challenge of meeting growing energy demand in a sustainable way, biodiesel has shown very promising as alternative energy can replace fossil fuels, even partially. Industrially, the biodiesel is produced by homogeneous transesterification reaction of vegetable oils in the presence of basic species used as catalysts. However, this process is the need for purification of the esters obtained and the removal of glycerin formed after the reaction. This context, the alternative catalysts have that can improve the process of biodiesel production, aiming to reduce costs and facilitate its production. In this study, the AlSBA-15 support with Si / Al ratio = 50 was synthesized, as like as the heterogeneous catalysts of zinc oxide and magnesium supported on mesoporous AlSBA-15 silica, in the concentrations of 5, 10, 15 and 30 %, relative to the support. The textural properties and structural characterization of catalysts and supports were determined by techniques: X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) coupled to the chemical analyzer, adsorption / desorption of N2, thermal analysis (TG / DTG), absorption spectroscopy in the infrared (FTIR) and X-ray photoelectron spectroscopy (XPS). Characterization results indicated that the support AlSBA-15 retained the hexagonal ordered after the incorporation of zinc oxide and magnesium oxide in the holder. For heterogeneous catalysts, ZnO-AlSBA-15, that was observed the presence of zinc oxide nanoparticles dispersed in the surface and interior channels of the mesoporous and microporous support. The catalytic activity was evaluated by the transesterification reaction of sunflower oil via methylic route, and some reaction parameters were optimized with the most active catalyst in biodiesel production by sunflower oil. For the series of heterogeneous catalysts, the sample with 30 % ZnO supported on AlSBA-15 showed a better conversion of triglyceride to methyl esters, about 95.41 % of reaction conditions: temperature 175 °C, with molar ratio of 42:1, stirring at 200 rpm and under a pressure of 14 bar for 6 h. The catalyst MgO-AlSBA-15 showed no catalytic activity in the studied reactions

A produção de biodiesel no assentamento Canudos RN: perspectivas e limites da inclusão social

The need to become energy self-sufficient a country with which Brazil has sought renewable energy sources due to the possibility of depletion of oil in coming decades. This paper will examine the perspective of social inclusion the latest energy plan developed by the Federal Government: the National Program of Biodiesel Production and Use - PNPB. It aims to find out whether that work with family farmers who participated in the PNPB socially included and what limits its inclusion. Secondly, the objective is to analyze the Brazilian biodiesel production and its uses. The methodology used for the preparation of this study was to examine the literature, visits to the study area, conducting interviews with the leadership of the settlement, questionnaires and semi-structured interviews with families producing sunflower. Finally, the research dealt with the statistical data. After analyzing the data was verified that the instrument PNPB is able to promote the social inclusion of family farmers, but this occurred in the initial stages because the families involved need a minimum framework of organization and infrastructure to develop activities related to biodiesel

O Circuito espacial de produção do biodiesel: configuração no território brasileiro e uso do território Norte-Rio-Grandense

This research aims to understand the use of the territory from the Rio Grande do Norte to the circuit spatial of production from the Biodiesel understanding it as part of the national context. The introduction of biodiesel into the Brazilian energy matrix begins to take shape in the year 2005 with the implementation of the National Program for Production and Use of Biodiesel (NPPB). This is anchored on three pillars: social inclusion (through family agriculture), environmental sustainability and economic viability. The NPPB consists of a set of standards, which turned into shares and distributed by almost all the national territory. Our reflection assumes that the places accommodating different forms of productive activities and, thus, the performance of the circuit space of biodiesel production depends on several factors, including the configuration of the territory they receive this new nexus economic. Understanding that the places by their technical content determine the realization of productive activities, it was found that the inclusion of this circuit space production in Rio Grande do Norte, reveals the reality expressed in the national territory, where some places are endowed with a privileged technical content and other extremely poor infrastructure. As our research could confirm the circuit space of biodiesel production that is expressed in the way plants are distributed within the country (mostly in South-Central), in more significant participation of small farmers in the South in the supply of raw material for the production of biodiesel and the main raw material used for the production of agrofuels (soybeans, whose production sector is highly consolidated and technified). Already the project materialization of NPPB regarding the settlements and communities of the Rio Grande do Norte State, we observed that the "event" or advent of realization encountered a technical means lacking in infrastructure that need to be molded to the needs of production, or is to cultivate castor beans or sunflower would be needed inputs and implements that farmers don´t have. Given the above, the research concludes that, as proposed previously, the use of the territory of Rio Grande do Norte to this circuit has summarized the performance of experiments, either with regard to the participation of family farmers as suppliers of raw materials, including the development of related research in the stage of production fuel oil by Petrobras. This finding came from research done from the concept of "spatial circuits of production," which allowed the verification of the circuit that steps outlined in Potiguar territory. Regarding the inclusion of family farmers in the productive circuit in RN, research reveals that, in the manner as has been done, it is doomed to failure. Furthermore, we dare say that this persistence in trying to put these family farmers, the way is being made, and the resulting successive failures, indicating that social inclusion advocated by NPPB not take place, and that this production circuit relies on the same logic circuit concentrated and exclusive space for ethanol production

Efeitos da suplementação de fitase sobre a disponibilidade aparente de Mg, Ca, Zn, Cu, Mn e Fe em alimentos vegetais para a tilápia-do-nilo

Cem juvenis de tilápia-do-nilo (Oreochromis niloticus; PV = 100.0 ± 5.0 g) foram distribuídos em 10 tanques-rede com o objetivo de avaliar o efeito da suplementação da enzima fitase (0, 1.000 e 2.000 UFA/kg) sobre a disponibilidade de minerais em alguns alimentos energéticos (milho, milho extrusado, farelo de trigo, farelo de arroz e farelo de sorgo) e protéicos (farelo de soja extrusado, farelo de soja, farelo de girassol, farelo de algodão e glúten de milho) utilizados na alimentação de tilápia-do-nilo (Oreochromis niloticus). Para determinação dos coeficientes de disponibilidade aparente (CDA) do cálcio (Ca), magnésio (Mg), zinco (Zn), cobre (Cu), ferro (Fe) e manganês (Mn), foram confeccionadas 31 rações, marcadas com 0,10% de óxido de crômio III uma referência (ração purificada) e 30 contendo os dez alimentos e os diferentes níveis de suplementação da enzima fitase. O CDA dos nutrientes foi calculado com base no teor de crômio da ração e das fezes. A fitase aumenta, nos vegetais, a disponibilidade do Mg, Cu, Zn e Mn, os quais apresentam tendência diferenciada, em razão do seu valor biológico e do nível de suplementação de enzima.

Disponibilidade aparente do fósforo em alimentos vegetais e suplementação da enzima fitase para tilápia-do-nilo

Este estudo foi realizado com o objetivo de avaliar o efeito da fitase (0, 1.000 e 2.000 uf/kg) na disponibilidade aparente de P de cinco alimentos energéticos (milho, milho extrusado, farelo de trigo, farelo de arroz e sorgo baixo tanino) e cinco alimentos protéicos (soja extrusada, farelo de soja, farelo de girassol, farelo de algodão e glúten de milho) utilizando-se uma ração purificada como controle. Foram utilizados 100 juvenis (100,00 ± 5,00 g) de tilápia-do-nilo (Oreochromis niloticus) alojados em dez gaiolas para manejo de alimentação e coleta de fezes. Para cada alimento e cada nível de fitase avaliado, foram coletadas amostras em cinco gaiolas, totalizando cinco repetições por tratamento. Os resultados obtidos indicaram que a suplementação de até 2.000 uf/kg de fitase não aumentou a disponibilidade aparente de P do farelo de trigo e do farelo de algodão. Entretanto, o nível de 1.000 uf/kg aumentou a disponibilidade aparente de P da soja extrusada e do farelo de girassol, enquanto o nível de 2.000 uf/kg proporcionou essa resposta para o farelo de milho, o milho extrusado, o sorgo baixo tanino, o farelo de arroz, o farelo de soja e o glúten de milho.