Electron acceleration by a propagating laser pulse in vacuum

Electrons accelerated by a propagating laser pulse of linear or circular polarization in vacuum have been investigated by one-dimensional particle-in-cell simulations and analytical modeling. A stopping target is used to stop the laser pulse and extract the energetic electrons from the laser field. The effect of the reflected light is taken into account. The maximum electron energy depends on the laser intensity and initial electron energy. There is an optimal acceleration length for electrons to gain maximum energy where electrons meet the peak of the laser pulse. The optimal acceleration length depends strongly on the laser pulse duration and amplitude. (C) 2007 American Institute of Physics.

二元振幅型面板用于光束空间整形

为了提高高功率激光系统的整体效率和充分利用光能,需要对前端注入的高斯光束进行空间整形,实现驱动器终端激光的均匀化输出。采用振幅型二元面板对激光光束进行空间强度整形,利用误差扩散法进行了理论设计,数值摸拟了整形效果,同时讨论了面板加工误差以及空间滤波器的小孔大小等因素带来的影响。根据理论设计,分别加工了反高斯透射率分布和抛物线透射率分布的二元面板,并进行了整形实验,实现了各自的整形功能,并做了误差分析。实验证明二元面板能对激光光束的空间强度分布实现了精确的整形。

110-W fiber laser with homemade double-clad fiber

A high-power ytterbium-doped fiber laser (YDFL) with homemade double-clad fiber (DCF) is introduced in this letter. The geometric parameter and laser characteristics of the fiber have been studied. With one-end-pumping scheme, pumped by a high-power laser diode with launching power of 280 W, a maximum continuous wave (CW) output of 110 W is obtained with an optical-to-optical efficiency of 40%.

Comparison of Yb-doped fiber laser with one-end and double-end pumping configuration

A high-power Ytterbium-doped fiber laser (YDFL) with homemade double clad fiber (DCF) is introduced in this paper. The output power characteristics of a linear cavity fiber laser have been studied theoretically by solving the rate equations and experimentally tested with single- and double-end-pumping configurations. When both ends of the fiber are pumped by two high-power laser diodes with a launched power of similar to 300 W each, a maximum CW output of 444 W is obtained with a slope efficiency of similar to 75%. (c) 2006 Elsevier Ltd. All rights reserved.

Low-threshold and continuously tunable Yb : Gd2SiO5 laser

Yb:Gd2SiO5 (Yb:GSO) exhibits a large fundamental manifold splitting. Its long-wavelength emission band around 1088 nm, which has the largest emission cross section, encounters the lowest reabsorption losses caused by thermal population of the terminal laser level. As a result, low-threshold and tunable continuous-wave Yb:GSO lasers were demonstrated. A slope efficiency up to 86% and a pumping threshold as low as 127 mW were achieved for a continuous-wave Yb:GSO laser at 1092.5 nm under the pump of a high-brightness laser diode. A continuous tunability between 1000 and 1120 nm was realized with an SF14 prism as the intracavity tuning element. (c) 2006 American Institute of Physics.

A novel non-intrusive sampling technique for CO2 laser on-line beam monitoring utilising a silicon mirror

The measurement of high speed laser beam parameters during processing is a topic that has seen growing attention over the last few years as quality assurance places greater demand on the monitoring of the manufacturing process. The targets for any monitoring system is to be non-intrusive, low cost, simple to operate, high speed and capable of operation in process. A new ISO compliant system is presented based on the integration of an imaging plate and camera located behind a proprietary mirror sampling device. The general layout of the device is presented along with the thermal and optical performance of the sampling optic. Diagnostic performance of the system is compared with industry standard devices, demonstrating the high quality high speed data which has been generated using this system.

Investigation of damage threshold to TiO2 coatings at different laser wavelength and pulse duration

Laser-induced damages to TiO2 single layers and TiO2/SiO2 high reflectors at laser wavelength of 1064 nm, 800 run, 532 urn, and pulse width of 12 ns, 220 ps, 50 fs, 8 ns are investigated. All films are prepared by electron beam evaporation. The relations among microstructure, chemical composition, optical properties and laser-induced damage threshold (LIDT), have been researched. The dependence of damage mechanism on laser wavelength and pulse width is discussed. It is found that from 1064 nm to 532 nm, LIDT is mainly absorption related, which is determined by film's extinction coefficient and stoichiometric defects. The rapid decrease of LIDT at 800 nm is due to the pulse width factor. TiO2 coatings are mainly thermally by damaged at long pulse (tau >= 220 ps). The damage shows ablation feature at 50 fs. (C) 2007 Elsevier B.V. All rights reserved.

Ecological limits of high-density milkfish farming

In the Philippines at present, milkfish farming in ponds includes a wide range of intensities, systems and practices. To make aquaculture possible, ecosystems are used as sources of energy and resources and as sinks for wastes. The growth of aquaculture is limited by the life-support functions of the ecosystem, and sustainability depends on matching the farming techniques with the processes and functions of the ecosystems, for example, by recycling some degraded resources. The fish farm has many interactions with the external environment. Serious environmental problems may be avoided if high-intensity farms are properly planned in the first place, at the farm level and at the level of the coastal zone where it can be integrated with other uses by other sectors. It is believed that the key to immediate success in the mass production of milkfish for local consumption and for export of value-added forms may be in semi-intensive farming at target yields of 3 tons per ha per year, double the current national average. Intensive milkfish farming will be limited by environmental, resource and market constraints. Integrated intensive farming systems are the appropriate long-term response to the triple needs of the next century: more food, more income, and more jobs for more people, all from less land, less resources, and less non-renewable energy.

Fabrication of high-aspect-ratio polymer microstructures and hierarchical textures using carbon nanotube composite master molds

Scalable and cost effective patterning of polymer structures and their surface textures is essential to engineer material properties such as liquid wetting and dry adhesion, and to design artificial biological interfaces. Further, fabrication of high-aspect-ratio microstructures often requires controlled deep-etching methods or high-intensity exposure. We demonstrate that carbon nanotube (CNT) composites can be used as master molds for fabrication of high-aspect-ratio polymer microstructures having anisotropic nanoscale textures. The master molds are made by growth of vertically aligned CNT patterns, capillary densification of the CNTs using organic solvents, and capillary-driven infiltration of the CNT structures with SU-8. The composite master structures are then replicated in SU-8 using standard PDMS transfer molding methods. By this process, we fabricated a library of replicas including vertical micro-pillars, honeycomb lattices with sub-micron wall thickness and aspect ratios exceeding 50:1, and microwells with sloped sidewalls. This process enables batch manufacturing of polymer features that capture complex nanoscale shapes and textures, while requiring only optical lithography and conventional thermal processing. © 2011 The Royal Society of Chemistry.

Novel coupled multi-active region high power semiconductor lasers cascaded via tunnel junction

A novel semiconductor laser structure is put forward to resolve the major difficulties of high power laser diodes. In this structure, several active regions are cascaded by tunnel junctions to form a large optical cavity and to achieve super high efficiency. This structure can solve the problems of catastrophic optical damage of facet, thermal damage and poor light beam quality effectively. Low-pressure metalorganic chemical vapor deposition method is adopted to grow the novel semiconductor laser structures, which are composed of Si:GaAs/C:GaAs tunnel junctions, GaAs/InGaAs strain quantum well active regions. External differential quantum efficiency as high as 2.2 and light power output of 2.5 W per facet (under 2A drive current) are achieved from an uncoated novel laser device with three active regions.

Beam dynamics design of an RFQ for a planned accelerator, which uses a direct plasma injection scheme

To meet the requirements of providing high-intensity heavy ion beams the direct plasma injection scheme (DPIS) was proposed by a RIKEN-CNS-TIT collaboration. In this scheme a radio frequency quadrupole (RFQ) was joined directly with the laser ion source (LIS) without a low-energy beam transport (LEBT) line. To find the best design of the RFQ that will have short length, high transmission efficiency and small emittance growth, beam dynamics designs with equipartitioning design strategy and with matched-only design strategy have been performed, and a comparison of their results has also been done. Impacts of the input beam parameters on transmission efficiency are presented, too. (C) 2008 Elsevier B.V. All rights reserved.

细粒沉积物多组分粒度特征及其成因机制研究

By using high-resolution laser grain size instrument Mastersizer 2000, the grain size distribution of windblown depositions (loess and sandy dunes), aqueous sediments (lake, river, riverside and foreshore sand), weathering crust, sloping materials and other fine-grain sediments are systemically measured. The multimodal characteristics of grain size distribution of these sediments are carefully studied. The standard patterns and their grain size characteristics of various sediments are systemically summarized. The discrepancies of multimodal distribution among windblown depositions, aqueous sediments and other sediments are concluded and the physical mechanisms of grain size multimodal distribution of various sediments are also discussed in this paper. The major conclusions are followed: 1. The multimodal characteristic of grain size distribution is a common feature in all sediments and results from properties of transportation medium, dynamic intensity, transportation manner and other factors. 2. The windblown depositions are controlled by aerodynamic forcing, resulting in that the median size of the predominant mode gradually decreases form sandy dunes to loess. Similarly, the aqueous sediments are impacted by dynamic forces of water currents and the median grain size of the predominant mode decreases gradually from river to lake sediments. Because the kinetic viscidity of air is lower than of water, the grain size of modes of windblown depositions is usually finer than that of corresponding modes of aqueous sediments. Typical characteristics of sediments grain size distribution of various sediments have been summarized in the paper: (1) Suspended particles which diameters are less than 75μm are dominant in loess and dust. There are three modes in loess’ grain size distribution: fine, median and coarse (the median size is <1μm、1-10μm、10-75μm, respectively). The coarse mode which percentage is larger than that of others is controlled by source distance and aerodynamic intensity of dust source areas. Some samples also have a saltation mode which median size is about 300-500μm. Our analysis demonstrates that the interaction of wind, atmospheric turbulence, and dust grain gravity along the dust transportation path results in a multimodal grain size distribution for suspended dust. Changes in the median sizes of the coarse and medium modes are related to variation in aerodynamic forcing (lift force related to vertical wind and turbulence) during dust entrainment in the source area and turbulence intensity in the depositional area. (2) There is a predominant coarse saltation mode in grain size distribution of sandy dunes, which median size is about 100-300μm and the content is larger than that of other modes. The grain size distribution curve is near axis symmetric as a standard logarithm normal function. There are some suspended particles in some samples of sandy dunes, which distribution of the fine part is similar to that of loess. Comparing with sandy samples of river sediments, the sorting property of sandy dunes is better than of river samples although both they are the saltation mode. Thus, the sorting property is a criterion to distinguish dune sands and river sands. (3) There are 5~6 modes (median size are <1μm, 1-10μm, 10-70μm, 70-150μm, 150-400μm, >400μm respectively) in grain size distribution of lacustrine sediments. The former 4 modes are suspensive and others are saltated. Lacustrine sediments can be divided into three types: lake shore facies, transitional facies and central lake facies. The grain size distributions of the three facies are distinctly different and, at the same time, the transition among three modes is also clear. In all these modes, the third mode is a criteria to identify the windblown deposition in the watershed. In lake shore sediments, suspended particles are dominant, a saltation mode sometimes occurs and the fourth mode is the most important mode. In the transitional facies, the percentage of the fourth mode decreases and that of the second mode increases from lake shore to central lake. In the central lake facies, the second mode is dominant. A higher content of the second mode indicates its position more close to the central lake. (4) The grain size distribution of river sediments is the most complex. It consist of suspension, saltation and rolling modes. In most situations, the percentage of the saltation mode is larger than that of other modes. The percentage of suspension modes of river sediments is more than of sandy dunes. The grain size distribution of river sediments indicates dynamic strength of river currents. If the fourth mode is dominant, the dynamic forcing of river is weaker, such as in river floodplain. If the five or sixth mode is dominant, the water dynamic forcing of rivers is strong. (5) Sediments can be changed by later forcing in different degree to form some complicated deposition types. In the paper, the grain size distribution of aqueous sediments of windblown deposition, windblown sediments of aqueous deposition, weathering crust and slope materials are discussed and analyzed. 3. The grain size distribution characteristics of different sediments are concluded: (1) Modal difference: Usually there are suspended and saltation modes in the windblown deposition. The third mode is dominant in loess dust and the fifth mode is predominant in sandy dunes. There are suspended, saltation and rolling particles in aqueous sediments. In lacustrine sediments, the second and fourth mode are predominant for central lake facies or lake shore facies, respectively. In river sediments, the fourth, or fifth, or sixth mode is predominant. Suspended modes: the grain size of suspended particles of windblown depositions usually is less than 75μm. The content of suspended particles is lower or none in sandy dunes. However, suspended particles of aqueous sediments may reach 150μm. Difference in grain size of suspended modes represents difference between transitional mediums and the strength of dynamic forcing. Saltation modes: the median size of saltation mode of sandy dunes fluctuates less than that of river sediments. (2) Loess dust and lacustrine sediment: Their suspended particles are clearly different. There is an obvious pit between the second and the third modes in grain size distribution of lacustrine sediments. The phenomenon doesn’t occur in loess dust. In lacustrine sediments, the second mode can be a dominant mode, such as central lake facies, and contents of the second and the third modes change reversely. However, the percentage of the third mode is always the highest in loess dust. (3) Dune Sand and fluvial sand: In these two depositions, the saltation particles are dominant and the median sizes of their saltation modes overlay in distribution range. The fifth mode of dune sand fluctuates is sorted better than that of fluvial sand. (4) Lacustrine and fluvial sediments: In lacustrine sediments, there are 5-6 modes and suspended particles can be predominant. The second mode is dominant in central lake facies and the third mode is dominant in lake shore facies. Saltation or roll modes occurred in central lake facies may indicate strong precipitation events. In fluvial sediments, saltation particles (or rolling particles) usually dominant. 4. A estimation model of lake depth is firstly established by using contents of the second, the third and the fourth modes. 5. The paleoenvironmental history of the eastern part of SongLiao basin is also discussed by analyzing the grain size distribution of Yushu loess-like sediments in Jilin. It was found that there is a tectonic movement before 40ka B.P. in SongLiao basin. After the movement, loess dust deposited in Yushu area as keerqin desert developed. In recent 2000 years, the climate became drier and more deserts activated in the eastern part of Song-Liao basin.

Laserterapia em Implantologia

Projeto de Pós-Graduação/Dissertação apresentado à Universidade Fernando Pessoa como parte dos requisitos para obtenção do grau de Mestre em Medicina Dentária

Laser de baixa intensidade na Regeneração Óssea

Projeto de Pós-Graduação/Dissertação apresentado à Universidade Fernando Pessoa como parte dos requisitos para obtenção do grau de Mestre em Medicina Dentária