Effects of promoters on catalytic activity and carbon deposition of Ni/gamma-Al2O3 catalysts in CO2 reforming of CH4

Catalytic reforming of methane with carbon dioxide was studied in a fixed-bed reactor using unpromoted and promoted Ni/gamma-Al2O3 catalysts. The effects of promoters, such as alkali metal oxide (Na2O), alkaline-earth metal oxides (MgO, CaO) and rare-earth metal oxides (La2O3, CeO2), on the catalytic activity and stability in terms of coking resistance and coke reactivity were systematically examined. CaO-, La2O3- and CeO2-promoted Ni/gamma-Al2O3 catalysts exhibited higher stability whereas MgO- and Na2O-promoted catalysts demonstrated lower activity and significant deactivation. Metal-oxide promoters (Na2O, MgO, La2O3, and CeO2) suppressed the carbon deposition, primarily due to the enhanced basicities of the supports and highly reactive carbon species formed during the reaction. In contrast, CaO increased the carbon deposition; however, it promoted the carbon reactivity. (C) 2000 Society of Chemical Industry.

Aluminium alloys - their physical and mechanical properties: Grain formation in AlSi7Mg0.35 foundry alloy at low superheat

Hypoeutectic AI-Si alloys represent the most widely used alloy system for cast aluminium applications. This system has a unique behaviour with respect to grain formation where an increase in silicon content results in a transition to larger grain sizes after a minimum at an intermediate concentration. As a result of the already large solute content, grain refinement by solute additions is inefficient and nucleant particles from the common aluminium grain refiners are not as effective as in wrought alloys. However, casting conditions, such as a low pouring temperature, that promote the formation of wall crystals tie. crystals nucleated in the thermally undercooled layer at or next to mould walls) are very effective in yielding a small grain size. This paper presents results of an investigation of the effect of low superheat and mould preheat temperature on grain size. It was found that pouring temperature controls the effectiveness of the wall mechanism while mould preheat has little effect until high preheat temperatures at which a large increase in grain size occurs. The observed changes in grain size are explained in terms of the balance between nucleation rate and survival rate of crystal nuclei resulting from changes in superheat and mould temperature.

Bimanual co-ordination in Huntington's disease

The ability of Huntington's disease patients to co-ordinate their two hands with and without external cueing was investigated. Twelve Huntington's disease patients and sex- and age-matched controls performed a bimanual cranking task at two speeds (0.5 Hz, 1.5 Hz) and phase relationships (in-phase, anti-phase), with and without an external metronome cue. Data were sampled at 200 Hz, and raw displacement data for each hand, mean and standard deviation measures of the relative positions of the two hands and their velocities were then calculated. All participants could perform the in-phase movement, at both speeds; however, the Huntington's disease patients were more variable and less accurate than the control participants, particularly at the fast speed. While controls could perform the anti-phase movement, in which rotation of the cranks differed by 180 degrees at both speeds, Huntington's disease patients were unable to do so at either speed, reverting to the in-phase movement at the slow speed. An external metronome cue did not improve the performance of the Huntington's disease patients, which differentiated this group from patients suffering from Parkinson's disease. The Huntington's disease patients' inability to perform the anti-phase movement may be due to damage to the basal ganglia and its output regions.

Reply to comments on "Oxidation mechanism of Si3N4-bonded SiC ceramics by CO, CO2 and steam," by Balat et al.

First of all, we would like to clarify that the passive to active transition was determined not by using Solgasmix [1], but by combining thermodynamic equilibrium and mass balance for the oxidation of SiC under pure CO2 and pure CO. The model used in our paper [2]was an extension ofWagner’s model [3], in a similar way as Balat et al. [4] did for the oxidation of SiC in oxygen.

A dual catalyst bed system for the elimination of hydrogen from CO2 feed gas in urea synthesis

A dual catalyst bed system (Au/Fe2O3 + Pt-Pd/Al2O3) for eliminating hydrogen from the CO2 feed gas in urea synthesis is found to be far superior to commercially available and patented catalysts in catalytic activity. At relatively low temperatures, hydrogen is eliminated and coexistent CO is also oxidized completely to useful CO2. This can avoid effectively the accidental explosion of hydrogen-oxygen-ammonia mixed gases, thus ensuring the safety of urea synthesis.

Co-morbidity between alcohol, tobacco and cannabis use: reply to David Fergusson

No abstract

Porous clays and pillared clays-based catalysts. Part 2: A review of the catalytic and molecular sieve applications

Metal oxide pillared clay (PILC) possesses several interesting properties, such as large surface area, high pore volume and tunable pore size (from micropore to mesopore), high thermal stability, strong surface acidity and catalytic active substrates/metal oxide pillars. These unique characteristics make PILC an attractive material in catalytic reactions. It can be made either as catalyst support or directly used as catalyst. This paper is a continuous work from Kloprogge's review (J.T. Kloprogge, J. Porous Mater. 5, 5 1998) on the synthesis and properties of smectites and related PILCs and will focus on the diverse applications of clay pillared with different types of metal oxides in the heterogeneous catalysis area and adsorption area. The relation between the performance of the PILC and its physico-chemical features will be addressed.

The co-segregation of psychosis and selected physical disorders within families of patients with psychosis versus well controls

While it has been reported that individuals with psychosis are at increased or decreased risk of various physical disorders such as cancer and rheumatoid arthritis, there has been less research on the co-segregation of physical disorders within the first-degree relatives of those with psychosis compared to relatives of well controls. The aim of this study was to examine these issues in an epidemiologically informed catchment-area based case-control study. Patients with psychosis were drawn from a prevalence study undertaken as part of the Australian National Mental Health Survey. In addition, we recruited well controls who resided in the same catchment area. For each subject, we drew pedigrees and used a structured checklist to assess the presence of selected psychiatric disorders, and selected disorders such as multiple sclerosis, epilepsy, spina bifida, thyroid disorders, diabetes, asthma and eczema. Data based on pedigrees from 293 individuals with psychosis and 292 well controls was available. As expected, the odds of havingschizophrenia and affective disorders were significantly increased in the families of cases versus controls. The odds of havingeczema were significantly reduced in the relatives of those with psychosis. All other disorders occurred with equal frequency in cases versus control pedigrees. Current theories of eczema suggest that an absence of early life exposure to antigens and infectious agents may fail to prime the na¨ıve immune system, and leave the person at increased risk of eczema. The results of this study suggest that genetic andror environmental factors that facilitate psychosis may protect against eczema. The Stanley Foundation supported this project.

Semisolid casting of AlSi7Mg0.35 alloy produced by low-temperature pouring

AlSi7Mg0.35 alloy was cast into permanent moulds using different pouring temperatures (725 to 625degreesC). As the pouring temperature decreased, the as-cast microstructure changed from a coarse dendritic structure, through fine equiaxed grains to fine rosette-like grains. The as-cast materials were then partially remelted and isothermally held at 580degreesC prior to semisolid casting into a stepped die. The feedstock material cast from a high temperature filled only half the die, with severe segregation and other defects. The low-temperature-poured material completely filled the die with negligible porosity. The quality of semisolid castings is significantly affected by the microstructure of the semisolid feedstock material that arises from a combination of as-cast and subsequent thermal treatment conditions. The paper describes (a) the influence of pouring temperature on the microstructure of feedstock; (b) microstructure evolution through remelting and (c) the quality of semisolid castings produced with this material. For A17Si0.35Mg alloy, low temperature pouring in the range of 625-650degreesC followed by suitable isothermal holding treatment can result in good quality semisolid casting.

Patterns of co-morbidity between alcohol use and other substance use in the Australian population

The present study describes patterns of co-morbidity between alcohol use and other substance use problems in the Australian population using data from the 1997 National Survey of Mental Health and Well-Being. Multiple regression analyses examined whether the observed associations between alcohol and other drug use disorders were explained by other variables, including demographic characteristics and neuroticism. We also assessed whether the presence of co-morbid substance use disorders affected treatment seeking for a mental health problem. Alcohol use was related strongly to the use of other substances. Those who did not report alcohol use within the past 12 months were less likely to report using tobacco, cannabis, sedatives, stimulants or opiates. Higher rates again were observed among those with alcohol use disorders: half (51%) of those who were alcohol-dependent were regular tobacco smokers, one-third had used cannabis (32%); 15% reported other drug use; 15% met criteria for a cannabis use disorder and 7% met criteria for another drug use disorder. These associations were not accounted for by the demographic and other variables considered here. Co-morbid substance use disorders (sedatives, stimulants or opioids) predicted a high likelihood of seeking treatment for a mental health problem among alcohol-dependent people.

Can metal complexes serve as hypoxia activated prodrugs? Investigations of a Co(III) complex of the MMP inhibitor marimastat

For many years proof that the hypoxic nature of malignant tumours can be used to selectively target anticancer drugs has been sought. Several classes of potential redox activated anticancer drugs have been developed to take advantage of the reducing environment resulting from the hypoxia. Drug complexes with redox active metal centres as carriers have been investigated, but have largely been employed with cytotoxic drugs that require release of the drug intracellularly, complicating the design of such complexes. MMP inhibitors, a new class of anticancer drug, conversely act in the extracellular environment and we have investigated inhibitor complexes with several redox active transition metals. Marimastat is an MMP inhibitor with potent in-vitro antimetastatic activity and was recently in Phase III clinical trials for a variety of cancer types. We have synthesised a Co(II1) complex of marimastat incorporating the tetradentate ligand tpa (tris(2-methylpyridyl)amine) as a carrier ligand. The complex was structurally characterised in the solid state by single crystal X-ray diffraction, the first example of a crystal structure containing marimastat. 2D COSY and NOESY NMR spectra showed that the complex exists in two isomeric forms in solution, corresponding to the cis and trans isomers yet only crystallises in one of these forms. Biological testing of the complex in mice with 4T1.2 tumours showed interesting and unexpected outcomes. Initial results of the tumour growth inhibition study showed that a significant inhibition of growth was exhibited by the complex over the free inhibitor and the control. However, the metastatic potential of both free marimastat and the complex were higher than the control indicating likely problems with the experimental protocol. Further experiments are needed to determine the potential of such complexes as hypoxia activated prodrugs but there appears at least to be some promise.

NMR characterization of blends of poly(hydroxybutyrate-co-hydroxyvalerate) with poly(vinyl acetate)

The extent of mixing in blends of poly(hydroxybutyrate-co-hydroxyvalerate) (PHBV) (27% HV) and poly(vinyl acetate) (PVAc) has been measured using a number of different techniques, principally solid-state NMR. Differential scanning calorimetry DSC measurements indicated effective mixing of the polymer chains on a scale of several nanometres. The results of H-1 T-1 and H-1 T-1rho. measurements confirm intimate mixing of the chains. A change on blending in the H-1 T-1rho, and the H-1 NMR line width of the signal from the protons of PVAc was consistent with an increase in the amplitude and frequency of motion of this component. The PVAc chains reside within the inter-lamellar space, as confirmed by spin diffusion measurements after H-1 T-1rho preparation. (C) 2003 Society of Chemical Industry.

Oxidation of toluene in waste gas streams using mesoporous Ti-hexagonal mesoporous silica

Various mesoporous catalysts with titanium loadings between 0.5 and 4 Ti wt. % and surface areas between 600 and 1,600 m(2)/g were synthesized using the molecular designed dispersion technique. These catalysts were tested using toluene oxidation in a fixed bed reactor at temperatures between 300 and 550degreesC. The reaction products were found to be CO2 and CO with selectivity towards CO2 above 80% for all catalysts. The catalytic activity of the catalysts increases with titanium loading. The total conversion at 550degreesC was not affected by the textural porosity, but increased textural porosity did significantly reduce the ignition temperature by up to 50degreesC. The Thiele modulus was calculated to be much less than one for all these materials indicating that the reaction rate is not diffusion, limited.

The game to play: expanding the co-opetition proposal through the strategic games matrix

Purpose - Using Brandenburger and Nalebuff`s 1995 co-opetition model as a reference, the purpose of this paper is to seek to develop a tool that, based on the tenets of classical game theory, would enable scholars and managers to identify which games may be played in response to the different conflict of interest situations faced by companies in their business environments. Design/methodology/approach - The literature on game theory and business strategy are reviewed and a conceptual model, the strategic games matrix (SGM), is developed. Two novel games are described and modeled. Findings - The co-opetition model is not sufficient to realistically represent most of the conflict of interest situations faced by companies. It seeks to address this problem through development of the SGM, which expands upon Brandenburger and Nalebuff`s model by providing a broader perspective, through incorporation of an additional dimension (power ratio between players) and three novel, respectively, (rival, individualistic, and associative). Practical implications - This proposed model, based on the concepts of game theory, should be used to train decision- and policy-makers to better understand, interpret and formulate conflict management strategies. Originality/value - A practical and original tool to use game models in conflict of interest situations is generated. Basic classical games, such as Nash, Stackelberg, Pareto, and Minimax, are mapped on the SGM to suggest in which situations they Could be useful. Two innovative games are described to fit four different types of conflict situations that so far have no corresponding game in the literature. A test application of the SGM to a classic Intel Corporation strategic management case, in the complex personal computer industry, shows that the proposed method is able to describe, to interpret, to analyze, and to prescribe optimal competitive and/or cooperative strategies for each conflict of interest situation.

Co-occurrence of three types of egg policing in the Norwegian wasp Dolichovespula norwegica

In insect societies, workers often try to challenge the reproductive monopoly of the queen by laying their own eggs. Successful worker reproduction, however, is frequently prevented by queen policing or worker policing, whereby either the mother queen or non-reproductive workers selectively kill worker-laid eggs. Recently, a third mechanism-""selfish"" worker policing-has also been described in which the workers selectively police worker-laid eggs but also lay eggs themselves. Here, we present results from the monogynous wasp Dolichovespula norwegica, which show that all three kinds of policing-queen policing, worker policing and ""selfish"" worker policing-co-occur. The net effect of these three kinds of policing collectively favoured the queen`s reproduction, as within 1 day 44% of the worker-laid eggs versus only 8% of the queen-laid eggs were eaten. Of the worker-laid eggs that were killed by workers, approximately two thirds were eaten by the reproductive workers even though these made up only a small proportion, 8%, of the work force. This means that policing workers obtained both direct fitness benefits as well as indirect (inclusive) fitness. In addition, we show that worker policing was carried out by a limited, specialised set of workers that was estimated to constitute approximately one quarter of the whole colony and of which 66% were non-reproductive.