The Effects of Some Furnish and Paper Structure Related Factors on Wet Web Tensile and Relaxation Characteristics

The objective of this thesis was to identify the effects of different factors on the tension and tension relaxation of wet paper web after high-speed straining. The study was motivated by the plausible connection between wet web mechanical properties and wet web runnability on paper machines shown by previous studies. The mechanical properties of wet paper were examined using a fast tensile test rig with a strain rate of 1000%/s. Most of the tests were carried out with laboratory handsheets, but samples from a pilot paper machine were also used. The tension relaxation of paper was evaluated as the tension remaining after 0.475 s of relaxation (residual tension). The tensile and relaxation properties of wet webs were found to be strongly dependent on the quality and amount of fines. With low fines content, the tensile strength and residual tension of wet paper was mainly determined by the mechanical interactions between fibres at their contact points. As the fines strengthen the mechanical interaction in the network, the fibre properties also become important. Fibre deformations caused by the mechanical treatment of pulp were shown to reduce the mechanical properties of both dry and wet paper. However, the effect was significantly higher for wet paper. An increase of filler content from 10% to 25% greatly reduced the tensile strength of dry paper, but did not significantly impair wet web tensile strength or residual tension. Increased filler content in wet web was shown to increase the dryness of the wet web after the press section, which partly compensates for the reduction of fibrous material in the web. It is also presumable that fillers increase entanglement friction between fibres, which is beneficial for wet web strength. Different contaminants present in white water during sheet formation resulted in lowered surface tension and increased dryness after wet pressing. The addition of different contaminants reduced the tensile strength of the dry paper. The reduction of dry paper tensile strength could not be explained by the reduced surface tension, but rather on the tendency of different contaminants to interfere with the inter-fibre bonding. Additionally, wet web strength was not affected by the changes in the surface tension of white water or possible changes in the hydrophilicity of fibres caused by the addition of different contaminants. The spraying of different polymers on wet paper before wet pressing had a significant effect on both dry and wet web tensile strength, whereas wet web elastic modulus and residual tension were basically not affected. We suggest that the increase of dry and wet paper strength could be affected by the molecular level interactions between these chemicals and fibres. The most significant increases in dry and wet paper strength were achieved with a dual application of anionic and cationic polymers. Furthermore, selectively adding papermaking chemicals to different fibre fractions (as opposed to adding chemicals to the whole pulp) improved the wet web mechanical properties and the drainage of the pulp suspension.

Development of chemical looping combustion process

Chemical looping combustion (CLC) provides a promising technology to help cut carbon dioxide emissions. CLC is based on separated oxidation and reduction processes. Oxygen carrier, which is made from metal and supporting material, is in continuous recirculation between the air and fuel reactors. The CLC process does not require separation unit for carbon dioxide. The fuel reactor can produce an almost pure carbon dioxide feed which decrease costs of carbon capture and storage (CCS). The CLC method is one of the most promising ones for energy efficient carbon capture. A large amount of literature was examined for this study and from it the most promising methods and designs were chosen. These methods and designs were combined as reactor system design which was then sized during the making of this thesis. Sizing was done with a mathematical model that was further improved during the study.

Working capital management in the value chain of automotive industry

The objective of this Master’s thesis is to examine working capital management in the automotive industry in years 2006-2008. The study is conducted by the analysis of financial statements. The sample consists of 65 companies that represent different stages in the value chain of automotive industry beginning from raw material suppliers and ending to car dealers. Working capital management is studied by the cash conversion cycle (CCC). The results show that the average CCC of the value chain is 67 days. Car manufacturers had the longest CCC, 106 days, whereas the CCC of oil companies was the shortest, 22 days. The findings suggest that the cycle time of working capital usually follows the cycle time of inventories, since the changes in cycle times of accounts receivable and payable compensate each other. Improvements in working capital management could be achieved by sharing more accurate information in the chain for example about inventory levels and order points of customer. It could also be discussed within the automotive industry, if the long credit periods, which tie up working capital, are really needed. New technologies enable faster payments, which would reduce the cash conversion cycles, improve the profitability of companies, and increase the competitiveness of the value chain. Working capital should not be reduced at the expense of value chain partners, because nowadays the competition is rather between the value chains than between the companies. Similar research design is applied earlier to study working capital management in the value chain of pulp and paper industry. Even if the industries and the structures of the chains differ from each other, results were surprisingly similar. In future research, working capital management in other industries’ value chains could still be studied and compared to previous studies. ICT industry, for example, could be an interesting object.

Topographic anatomical study of the sciatic nerve relationship to the posterior portal in hip arthroscopy

Objective: To evaluate the anatomic topographic relation between the sciatic nerve in relation to the piriform muscle and the posterior portal for the establishment of hip arthroscopy.Methods: We dissected 40 hips of 20 corpses of adult Brazilians, 17 male and three female, six black, six brown and eight white. We studied the anatomical relationship between the sciatic nerve and the piriform muscle with their variations and the distance between the lateral edge of the sciatic nerve and the posterior portal used in hip arthroscopy. We then classified the anatomical alterations found in the path of the sciatic nerve on the piriform muscle.Results: Seventeen corpses had bilateral relationship between the sciatic nerve and the piriform muscle, i.e., type A. We found the following anatomical variations: 12.5% of variant type B; and an average distance between the sciatic nerve and the portal for arthroscopy of 2.98cm. One body had type B anatomical variation on the left hip and type A on the right.Conclusion: the making of the posterior arthroscopic portal to the hip joint must be done with careful marking of the trochanter massive; should there be difficult to find it, a small surgical access is recommended. The access point to the portal should not exceed two centimeters towards the posterior superior aspect of the greater trochanter, and must be made with the limb in internal rotation of 15 degrees.

Immediate Decision-Making and Information Needs in Intensive Care Coordination

The aim of this study was to develop a theoretical model for information integration to support the deci¬sion making of intensive care charge nurses, and physicians in charge – that is, ICU shift leaders. The study focused on the ad hoc decision-making and immediate information needs of shift leaders during the management of an intensive care unit’s (ICU) daily activities. The term ‘ad hoc decision-making’ was defined as critical judgements that are needed for a specific purpose at a precise moment with the goal of ensuring instant and adequate patient care and a fluent flow of ICU activities. Data collection and research analysis methods were tested in the identification of ICU shift leaders’ ad hoc decision-making. Decision-making of ICU charge nurses (n = 12) and physicians in charge (n = 8) was observed using a think-aloud technique in two university-affiliated Finnish ICUs for adults. The ad hoc decisions of ICU shift leaders were identified using an application of protocol analysis. In the next phase, a structured online question¬naire was developed to evaluate the immediate information needs of ICU shift leaders. A national survey was conducted in all Finnish, university-affiliated hospital ICUs for adults (n = 17). The questionnaire was sent to all charge nurses (n = 515) and physicians in charge (n = 223). Altogether, 257 charge nurses (50%) and 96 physicians in charge (43%) responded to the survey. The survey was also tested internationally in 16 Greek ICUs. From Greece, 50 charge nurses out of 240 (21%) responded to the survey. A think-aloud technique and protocol analysis were found to be applicable for the identification of the ad hoc decision-making of ICU shift leaders. During one day shift leaders made over 200 ad hoc decisions. Ad hoc decisions were made horizontally, related to the whole intensive care process, and vertically, concerning single intensive care incidents. Most of the ICU shift leaders’ ad hoc decisions were related to human resources and know-how, patient information and vital signs, and special treatments. Commonly, this ad hoc decision-making involved several multiprofessional decisions that constituted a bundle of immediate decisions and various information needs. Some of these immediate information needs were shared between the charge nurses and the physicians in charge. The majority of which concerned patient admission, the organisation and management of work, and staff allocation. In general, the information needs of charge nurses were more varied than those of physicians. It was found that many ad hoc deci-sions made by the physicians in charge produced several information needs for ICU charge nurses. This meant that before the task at hand was completed, various kinds of information was sought by the charge nurses to support the decision-making process. Most of the immediate information needs of charge nurses were related to the organisation and management of work and human resources, whereas the information needs of the physicians in charge mainly concerned direct patient care. Thus, information needs differ between professionals even if the goal of decision-making is the same. The results of the international survey confirmed these study results for charge nurses. Both in Finland and in Greece the information needs of charge nurses focused on the organisation and management of work and human resources. Many of the most crucial information needs of Finnish and Greek ICU charge nurses were common. In conclusion, it was found that ICU shift leaders make hundreds of ad hoc decisions during the course of a day related to the allocation of resources and organisation of patient care. The ad hoc decision-making of ICU shift leaders is a complex multi-professional process, which requires a lot of immediate information. Real-time support for information related to patient admission, the organisation and man¬agement of work, and allocation of staff resources is especially needed. The preliminary information integration model can be applied when real-time enterprise resource planning systems are developed for intensive care daily management

Surface characterization of chemically modified fiber, wood and paper

Inorganic-organic sol-gel hybrid coatings can be used for improving and modifying properties of wood-based materials. By selecting a proper precursor, wood can be made water repellent, decay-, moisture- or UV-resistant. However, to control the barrier properties of sol-gel coatings on wood substrates against moisture uptake and weathering, an understanding of the surface morphology and chemistry of the deposited sol-gel coatings on wood substrates is needed. Mechanical pulp is used in production of wood-containing printing papers. The physical and chemical fiber surface characteristics, as created in the chosen mechanical pulp manufacturing process, play a key role in controlling the properties of the end-use product. A detailed understanding of how process parameters influence fiber surfaces can help improving cost-effectiveness of pulp and paper production. The current work focuses on physico-chemical characterization of modified wood-based materials with surface sensitive analytical tools. The overall objectives were, through advanced microscopy and chemical analysis techniques, (i) to collect versatile information about the surface structures of Norway spruce thermomechanical pulp fiber walls and understand how they are influenced by the selected chemical treatments, and (ii) to clarify the effect of various sol-gel coatings on surface structural and chemical properties of wood-based substrates. A special emphasis was on understanding the effect of sol-gel coatings on the water repellency of modified wood and paper surfaces. In the first part of the work, effects of chemical treatment on micro- and nano-scale surface structure of 1st stage TMP latewood fibers from Norway spruce were investigated. The chemicals applied were buffered sodium oxalate and hydrochloric acid. The outer and the inner fiber wall layers of the untreated and chemically treated fibers were separately analyzed by light microscopy, atomic force microscopy and field-emission scanning electron microscopy. The selected characterization methods enabled the demonstration of the effect of different treatments on the fiber surface structure, both visually and quantitatively. The outer fiber wall areas appeared as intact bands surrounding the fiber and they were clearly rougher than areas of exposed inner fiber wall. The roughness of the outer fiber wall areas increased most in the sodium oxalate treatment. The results indicated formation of more surface pores on the exposed inner fiber wall areas than on the corresponding outer fiber wall areas as a result of the chemical treatments. The hydrochloric acid treatment seemed to increase the surface porosity of the inner wall areas. In the second part of the work, three silane-based sol-gel hybrid coatings were selected in order to improve moisture resistance of wood and paper substrates. The coatings differed from each other in terms of having different alkyl (CH3–, CH3-(CH2)7–) and fluorocarbon (CF3–) chains attached to the trialkoxysilane sol-gel precursor. The sol-gel coatings were deposited by a wet coating method, i.e. spraying or spreading by brush. The effect of solgel coatings on surface structural and chemical properties of wood-based substrates was studied by using advanced surface analyzing tools: atomic force microscopy, X-ray photoelectron spectroscopy and time-of-flight secondary ion spectroscopy. The results show that the applied sol-gel coatings, deposited as thin films or particulate coatings, have different effects on surface characteristics of wood and wood-based materials. The coating which has a long hydrocarbon chain (CH3-(CH2)7–) attached to the silane backbone (octyltriethoxysilane) produced the highest hydrophobicity for wood and wood-based materials.

Industrial-Scale hydrothermal carbonization of waste sludge materials for fuel production

Hydrothermal carbonization (HTC) is a thermochemical process used in the production of charred matter similar in composition to coal. It involves the use of wet, carbohydrate feedstock, a relatively low temperature environment (180 °C-350 °C) and high autogenous pressure (up to 2,4 MPa) in a closed system. Various applications of the solid char product exist, opening the way for a range of biomass feedstock materials to be exploited that have so far proven to be troublesome due to high water content or other factors. Sludge materials are investigated as candidates for industrial-scale HTC treatment in fuel production. In general, HTC treatment of pulp and paper industry sludge (PPS) and anaerobically digested municipal sewage sludge (ADS) using existing technology is competitive with traditional treatment options, which range in price from EUR 30-80 per ton of wet sludge. PPS and ADS can be treated by HTC for less than EUR 13 and 33, respectively. Opportunities and challenges related to HTC exist, as this relatively new technology moves from laboratory and pilot-scale production to an industrial scale. Feedstock materials, end-products, process conditions and local markets ultimately determine the feasibility of a given HTC operation. However, there is potential for sludge materials to be converted to sustainable bio-coal fuel in a Finnish context.

Let's do data research work: the creation of a portal with research information from Catalan Universities

Presentation at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

Marketing of fire suppression systems: customer value and institutional aspects

The paper studied marketing of automatic fire suppression systems from the perspectives of customer value and institutions. The object of the study was research the special features of the sales and marketing of fire suppression systems, and find some practical applications for sales, and for lobbying of a new fire suppression technology. The theoretical background of the study was in the customer value literature and the theoretical concept of institutional entrepreneurship. The research was conducted as an electronic survey for three different groups of respondents; end customers, solution integrators, and re-sellers. From the answers was gathered generalisations about the customer value assessment and communication of the value related to the sales and marketing processes of the fire suppression systems. In addition, there was observed manners to receive information about the systems, and effects caused by institutions to the decision making of the different parties involved. The findings of the study support companies that are launching a new safety technology to the market focus their marketing, and help to understand institutional forces that are affecting to a safety related product.

Feasibility of the use of recycled nutrients in fast growing pulpwood production

The application of pulp and paper mill (PPM) sludge in agriculture and forestry has been acknowledged as soil amendments and a plant nutrient source. The main objectives of this study were to evaluate the total cost of the use of recycled nutrients from PPM sludge in fast growing pulpwood production, and the financial profitability of fast growing pulpwood production with the use of these recycled nutrients. The investment and production costs of fast growing pulpwood plantation were directly acquired from a previous research, while the other data was compiled through different studies. The total cost of the use of PPM sludge was evaluated based on assumed factors. Discounted cash flow method was used to evaluate the financial profitability, using NPV and IRR as indicators. The results of estimated sludge nutrient contents were 16.2 g N, 2.9 g P, and 2.4 g K kg-1 of dry sludge. The sludge application rate was estimated at 1.36 Mg/ha in the first year. The total cost of the use of PPM sludge involved transport and spreading cost of US$49.15/dry ton. The fertilization cost applied in the financial model was designed in 3 different options and their results were as follows: option (1) was taken directly from the reference research (US$97/ha); option (2) was the use of sludge alone (US$66.75/ha); and option (3) was the use of sludge and TSP fertilizer (US$83.80/ha). The average NPV without discounting was US$248,180 while the IRRs ranged between approximately 3-4% with an average of 3.63%. Although option (2) and (3) contributed to higher IRRs compared to option (1), this increase was still not significant as the IRR was not sensitive to the total fertilization cost. The advantages are that this practice can be performed at a lower cost and the application rate can be still increased if necessary. It is better for forest plantations compared to agriculture and consequently supports reforestation program. In addition, it can be similarly applied in wood biomass production. A disadvantage is that the IRRs were not very favorable compared to the criterion of 11%. The sludge high in C:N ratio can cause nitrogen immobilization, and regulatory concerns may restrict and complicate the use of sludge landspreading and contribute to additional costs and processes.

Apply of energy storages in electricity distribution networks and reserve capacity applications

The Thesis is dedicated to development of an operative tool to support decision making of battery energy storages implementation in distribution networks. The basics of various battery technologies, their perspectives and challenges are represented in the Thesis. Mathematical equations that describe economic effect from battery energy storage installation are offered. The main factors that influence profitability of battery settings have been explored and mathematically defined. Mathematical model and principal trends of battery storage profitability under an impact of the major factors are determined. The meaning of annual net value was introduced to show the difference between savings and required costs. The model gives a clear vision for dependencies between annual net value and main factors. Proposals for optimal network and battery characteristics are suggested.

Carbon footprint of recycled paper

Industrial production of pulp and paper is an intensive consumer of energy, natural resources, and chemicals that result in a big carbon footprint of the final product. At present companies and industries aspire to calculate their gas emissions into the atmosphere in order to afterwards reduce atmospheric contamination. One of the approaches allowing to increase carbon burden from the pulp and paper manufacture is paper recycling. The general purpose of the current paper is to establish methods of quantifying and minimizing the carbon footprint of paper. The first target of this research is to derive a mathematical relationship between virgin fibre requirements with respect to the amount of recycled paper used in the pulp. One more purpose is to establish a model to be used to clarify the contribution of recycling and transportation to decreasing carbon dioxide emissions. For this study sensitivity analysis is used to investigate the robustness of obtained results. The results of the present study show that an increasing of recycling rate does not always lead to minimizing the carbon footprint. Additionally, we derived that transportation of waste paper throughout distances longer than 5800 km has no sense because the use of that paper will only increase carbon dioxide emissions and it is better to reject recycling at all. Finally, we designed the model for organization of a new supply chain of paper product to a customer. The models were implemented as reusable MATLAB frameworks.

Chemical and physical characterization of mume fruit collected from different locations and at different maturity stages in São Paulo State

Prunus mume is widely studied due to its health benefits regarding increase of blood fluidity and consequent improvement of the cardiovascular system and the prevention or even the fight against different types of cancer. However, in Brazil this culture is found only among oriental descendants. The present study aimed to characterize mume fruit collected from three different locations in the State of São Paulo regarding general aspects such as pH, total titratable acidity (TTA), total soluble solids (TTS), pectin content and yield of pulp and chemical characteristics: total phenolic compounds (TPC) and antioxidant capacity. Mume fruit were collected unripe and analyzed until maturation about 88 days after flowering. Fruit collected in Botucatu came from a commercial mume fruit producer and had average weight of 16.9 g, while in fruit from other locations weight varied from 5.7-6.9 g. TSS ranged from 9.5 to 10.0 Brix, total solids was 10.2-12.2% and pH showed values between 2.5 and 2.7 for all locations. TTA expressed in citric acid decreased from 4.0-5.7 g (100g- 1) at unripe stage to 2.0-3.8 g (100g- 1) in mature-stage fruit. Pectin content decreased from 11.2 to 10.8% during fruit maturation, TPC content was 147-226 mg catechin (g- 1) on a dry matter basis and the antioxidant capacity was 96-169 µMol Trolox (g- 1) on a dry matter basis or 21-34 µMol Trolox (g- 1) on a wet matter basis.

Use of simulated annealing in standardization and optimization of the acerola wine production

In this study, seven wine samples were prepared varying the amount of pulp of acerola fruits and the sugar content using the simulated annealing technique to obtain the optimal sensory qualities and cost for the wine produced. S. cerevisiae yeast was used in the fermentation process and the sensory attributes were evaluated using a hedonic scale. Acerola wines were classified as sweet, with 11°GL of alcohol concentration and with aroma, taste, and color characteristics of the acerola fruit. The simulated annealing experiments showed that the best conditions were found at mass ratio between 1/7.5-1/6 and total soluble solids between 28.6-29.0 °Brix, from which the sensory acceptance scores of 6.9, 6.8, and 8.8 were obtained for color, aroma, and flavor, respectively, with a production cost 43-45% lower than the cost of traditional wines commercialized in Brazil.

Influence of different cultivars on oil quality and chemical characteristics of avocado fruit

The objective of this paper was to determine the chemical composition of the avocado fruit of cultivars Fortuna, Collinson, and Barker and to carry out a detailed analysis of the fatty acid composition of the pulp, seed, and peel oils. The saturated fatty acid (SFA) of the pulp oils accounted for around 22.3, 29.4, and 41.3% of the total fatty acids in the Fortuna, Collinson and Barker cultivars, respectively, and these values indicate better quality of pulp oil of Fortuna and Collinson cultivars than that of the Barker cultivar. There was very little variation in the content monounsaturated fatty acids of the peel oils between the cultivars. However, the seed oil of the Collinson cultivar was the best since it contained the lowest (30.8% of total fatty acids) content of SFA, but it had very high concentrations of 9,12-octadecadienoic (23.9 to 29.4% of total fatty acids) and 9,12,15-octadecatrienoic (9.9 to 18.3% of total fatty acids) acids.