基于网络化虚拟仪器的机器人传感器实验平台

设计了基于网络化虚拟仪器的多节点机器人传感器实验平台系统,利用COM、软件插件等技术开发了虚拟控件和信号处理软件模块,用户可通过PPL创建自定义的信号处理模块,为进行面向智能机器人控制的传感器测试、标定、组网等奠定了基础。

一类载人潜水器的导航技术研究

介绍了一类载人潜水器导航系统的组成,接着阐述了基于工业以太网的信息采集模块.由于载人潜水器动力学模型存在未建模扰动以及各种传感器存在不同程度的误差,需要采用卡尔曼滤波器(KF)等方法进行数据滤波,最后将滤波后的数据用于该类载人潜水器的导航研究.半物理仿真平台结果表明,载人潜水器的导航精度得到了大幅度提高.

金川矿山岩体移动规律及竖井变形、破坏机理研究

The Jinchuan Nickel Mine is the largest underground mine with cut-and-fill mining in China. It is very difficult to be exploited for very low safety stability of rock mass caused by complex geological conditions, developed faults, cracked rock mass and high stress. In this paper, the laws of rock mass movement、mechanics of shaft deformation and destroy were analyzed based on the collection of date, the detailed field engineering investigations, ground movement monitoring by GPS, theoretical analysis and numerical simulation. According to the GPS monitoring result of ground surface movement, there are different ground movement characteristics among the three Mine area of Jinchuan Nickel Mine. In No. 2 Mine area, the ground movement funnel with apparent asymmetry is developing, the influence scope is larger in the up faulted block than in the down faulted block, and the centre of ground movement is moving along the up faulted block direction with increasing depth of mining. Moreover, the tunnels in the corresponding area with the centre of ground movement are damaged seriously. In Longshou Mine area, the ground movement funnel is also developing, but the moving path and the nonlinear characters are more sophisticated because of the long-term effects of open excavating and the effects of underground mining together. In No. 3 Mine area, the underground mining impact on surface is not serious for the time of mining activity is not for long, but the ground movement funnel is also forming now. The underground mining has caused widespread land subsidence in Jinchuan Nickel Mine area, but the phenomena of surface raise appeared in some partial areas of Longshou Mine area and No. 3 Mine area. Analysis proved that the reason for the open pit bottom raise is the slope deformation activation caused by the excavation from open pit into underground mine; and that the raise of surface in No.3 Mine area is caused by the effect of elastic foundation due to underground mining. Although the GPS Monitoring results show the amount of subsidence is increasing constantly, the subsidence rate has a descending tendency with fluctuation in Jinchuan No. 2 Mine area. The subsidence rate curve is a time function and exists an extreme point, the rate increasing before extreme point and decreasing after the extreme point ,but the scale of decreasing rate will be very small after the rate decreasing up to a certain degree, moreover, the characteristics is different among different areas, which have some relation with the distance to the mining section and the dip of the ore body. ArcView is GIS software, which we adopted as a development platform, and made secondary development by its development language “avenue”, through which we developed a ground movement analysis and forecast System for Jinchuan Nickel Mine, which contain three modules : management of ground movement information; analysis and evaluation of ground movement; and ground movement forecast. In the module of evaluation, using the technique of MATLAB6.5 program with VB6.0, the system can achieve the ANN prediction model for GPS monitoring data, data preparation results analysis and model integrated was realized by Avenue programming. Finally, the author analyzed the mechanical of deformation and destroy of the No. 14 shaft, and its repair and artificial-support effectiveness also given detailed demonstration in various aspect. The result showed that the reason for the destroy of No. 14 shaft is underground mining, and being the case, the destroy of the shaft also has its special features, which mainly contains forked stress contour for mining steep ore and fault effect caused by mining activities. The repair and artificial-support played some restrictions on the rock mass movement and deformation, but did not show a strong or marked effect. With the increasing of mining depth and large-scale, the closure rock of the shaft will still deformed, even be destroyed.

工程地质三维建模与可视化技术应用开发

Synthetic Geology Information System (SGIS) is an important constituent part of the theory of Engineering Geomechanics Mate-Synthetic (EGMS), and is the information system more suited for the collection, storage, management, analysis and processing to the information coming from engineering geology,' geological engineering and geotechnical engineering. Its contents involve various works and methods of the investigation, design, and construction in different stages of the geological engineering. Engineering geological and three-dimensional modeling and visualization is the fundamental part of the SGIS, and is a theory, method and technique by which, adopting the computer graphics and image processing techniques, the data derived from engineering geological survey and the calculated results obtained from the geomechanical numerical simulation and analysis are converted to the graphics and images displayed on the computer screen and can be processed interactively. In this paper, the significance and realizing approaches of the three-dimensional modeling and visualization for the complex geological mass in the engineering geology are discussed and the methods of taking advantage of the interpolation and fitting for the scattered and field-surveyed data to simulate the geological layers, such as the topography and earth surface, the groundwater table and the stratum boundary, are researched into. At the mean time, in mind the characteristics of the structure of the basic data for three-dimensional modeling, its visual management can be resolved into the engineering surveyed database management module, plot parameter management module and data output module and the requirement for basic data management can be fulfilled. In the paper, the establishment and development of the three-dimensional geological information system are probed tentatively, and an instance of three-dimensional visual Engineering Distribution Information System (EDIS), theConstruction Management Information System for an airport, in which the functions, such as the real-time browse among the three-dimensional virtual-reality landscapes of the airport construction from start to finish, the information query to the airport facility and the building in the housing district and the recording and playback of the animation sets for the browse and the takeoff and landing of the planes, is developed by applying the component-mode three-dimensional virtual-reality geological information system (GIS) software development kits (SDK), so the three-dimensional visual management platform is provided for the airport construction. Moreover, in the gaper, integrated with the three-dimensional topography visualization and its application in the Sichuan-Tibet Highways, the method of the digital elevation model (DEM) data collection from the topographic maps is described, and the three-dimensional visualization and the roaming about the terrain along the highway are achieved through computer language programming. Understanding to the important role played by the varied and unique topographical condition in the gestation and germination of the highly-dense, frequently-arising and severely-endangered geological hazards can be deepened.

地震勘探三维可视化方法研究与实现

This thesis mainly studies the technologies of 3-D seismic visualization and Graphic User Interface of seismic processing software. By studying Computer Graphics and 3-D geological modeling, the author designs and implements the visualization module of seismic data processing software using OpenGL and Motif. Setting seismic visualization flow as the subject, NURBS surface approximation and Delaunay Triangulation as the two different methods, the thesis discusses the key algorithms and technologies of seismic visualization and attempts to apply Octree Space Partitioning and Mip Mapping to enhance system performance. According to the research mentioned above, in view of portability and scalability, the author adopts Object-oriented Analysis and Object-oriented Design, uses standard C++ as programming language, OpenGL as 3-D graphics library and Motif as GUI developing tool to implement the seismic visualization framework on SGI Irix platform. This thesis also studies the solution of fluid equations in porous media. 2-D alternating direction implicit procedure has been turned into 3-D successive over relaxation iteration, which possesses such virtues as faster computing speed, faster convergence rate, better adaptability to heterogeneous media and less memory demanding.

人口统计信息空间可视化系统研究

Population research is a front area concerned by domestic and overseas, especially its researches on its spatial visualization and its geo-visualization system design, which provides a sound base for understanding and analysis of the regional difference in population distribution and its spatial rules. With the development of GIS, the theory of geo-visualization more and more plays an important role in many research fields, especially in population information visualization, and has been made the big achievements recently. Nevertheless, the current research is less attention paid to the system design for statistical-geo visualization for population information. This paper tries to explore the design theories and methodologies for statistical-geo-visualization system for population information. The researches are mainly focused on the framework, the methodologies and techniques for the system design and construction. The purpose of the research is developed a platform for population atlas by the integration of the former owned copy software of the research group in statistical mapping system. As a modern tool, the system will provide a spatial visual environment for user to analyze the characteristics of population distribution and differentiate the interrelations of the population components. Firstly, the paper discusses the essentiality of geo-visualization for population information and brings forward the key issue in statistical-geo visualization system design based on the analysis of inland and international trends. Secondly, the geo-visualization system for population design, including its structure, functionality, module, user interface design, is studied based on the concepts of theory and technology of geo-visualization. The system design is proposed and further divided into three parts: support layer, technical layer, user layer. The support layer is a basic operation module and main part of the system. The technical layer is a core part of the system, supported by database and function modules. The database module mainly include the integrated population database (comprises spatial data, attribute data and geographical features information), the cartographic symbol library, the color library, the statistical analysis model. The function module of the system consists of thematic map maker component, statistical graph maker component, database management component and statistical analysis component. The user layer is an integrated platform, which provides the functions to design and implement a visual interface for user to query, analysis and management the statistic data and the electronic map. Based on the above, China's E-atlas for population was designed and developed by the integration of the national fifth census data with 1:400 million scaled spatial data. The atlas illustrates the actual development level of the population nowadays in China by about 200 thematic maps relating with 10 map categories(environment, population distribution, sex and age, immigration, nation, family and marriage, birth, education, employment, house). As a scientific reference tool, China's E-atlas for population has already received the high evaluation after published in early 2005. Finally, the paper makes the deep analysis of the sex ratio in China, to show how to use the functions of the system to analyze the specific population problem and how to make the data mining. The analysis results showed that: 1. The sex ratio has been increased in many regions after fourth census in 1990 except the cities in the east region, and the high sex ratio is highly located in hilly and low mountain areas where with the high illiteracy rate and the high poor rate; 2. The statistical-geo visualization system is a powerful tool to handle population information, which can be used to reflect the regional differences and the regional variations of population in China and indicate the interrelations of the population with other environment factors. Although the author tries to bring up a integrate design frame of the statistical-geo visualization system, there are still many problems needed to be resolved with the development of geo-visualization studies.

A module-based approach to foster and document the intercultural process before and during the residence abroad.

This article contributes to the debate on what form of preparation and support can enhance the intercultural student experience during the Year Abroad. It presents a credit-bearing and multi-modal module at a UK university designed to both prepare students prior to departure through a series of workshops and activities on an e-portfolio and help them engage in meta-reflection on intercultural issues during their stay. The presentation of the curricular components of the course and instances extracted from student blogs are contextualised within theoretical considerations on intercultural education and a holistic approach to student development. The longitudinal evolution of the module is presented in the context of an iterative approach leading to a cycle of revisions and amendments. With its pragmatic stance this article aims to address one of the concerns recently expressed about intercultural education, namely that although intercultural theories are suitably incorporated in the latest thinking on communicative competence, there is a lack of evidence-based practice.

DSpace Manual: Software version 1.5

DSpace is an open source software platform that enables organizations to: - Capture and describe digital material using a submission workflow module, or a variety of programmatic ingest options - Distribute an organization's digital assets over the web through a search and retrieval system - Preserve digital assets over the long term This system documentation includes a functional overview of the system, which is a good introduction to the capabilities of the system, and should be readable by nontechnical personnel. Everyone should read this section first because it introduces some terminology used throughout the rest of the documentation. For people actually running a DSpace service, there is an installation guide, and sections on configuration and the directory structure. Note that as of DSpace 1.2, the administration user interface guide is now on-line help available from within the DSpace system. Finally, for those interested in the details of how DSpace works, and those potentially interested in modifying the code for their own purposes, there is a detailed architecture and design section.

The CLARITY modular ambient health and wellness measurement platform

Emerging healthcare applications can benefit enormously from recent advances in pervasive technology and computing. This paper introduces the CLARITY Modular Ambient Health and Wellness Measurement Platform:, which is a heterogeneous and robust pervasive healthcare solution currently under development at the CLARITY Center for Sensor Web Technologies. This intelligent and context-aware platform comprises the Tyndall Wireless Sensor Network prototyping system, augmented with an agent-based middleware and frontend computing architecture. The key contribution of this work is to highlight how interoperability, expandability, reusability and robustness can be manifested in the modular design of the constituent nodes and the inherently distributed nature of the controlling software architecture.Emerging healthcare applications can benefit enormously from recent advances in pervasive technology and computing. This paper introduces the CLARITY Modular Ambient Health and Wellness Measurement Platform:, which is a heterogeneous and robust pervasive healthcare solution currently under development at the CLARITY Center for Sensor Web Technologies. This intelligent and context-aware platform comprises the Tyndall Wireless Sensor Network prototyping system, augmented with an agent-based middleware and frontend computing architecture. The key contribution of this work is to highlight how interoperability, expandability, reusability and robustness can be manifested in the modular design of the constituent nodes and the inherently distributed nature of the controlling software architecture.

Remote electricity actuation and monitoring mote

This work presents the design and evaluation of the REAM (Remote Electricity Actuation and Monitoring) node based around the modular Tyndall Mote platform. The REAM node enables the user to remotely actuate power to a mains power extension board while sampling the current, voltage, power and power factor of the attached load. The node contains a current transformer interfaced to an Energy Metering IC which continuously samples current and voltage. These values are periodically read from the part by a PIC24 microcontroller, which calculates the RMS current and voltage, power factor and overall power. The resultant values can then be queried wirelessly employing the Tyndall 802.15.4 compliant wireless module.

The s-mote: a versatile heterogeneous multi-radio platform for wireless sensor networks applications

This paper presents a novel architecture and its implementation for a versatile, miniaturised mote which can communicate concurrently using a variety of combinations of ISM bands, has increased processing capability, and interoperability with mainstream GSM technology. All these features are integrated in a small form factor platform. The platform can have many configurations which could satisfy a variety of applications’ constraints. To the best of our knowledge, it is the first integrated platform of this type reported in the literature. The proposed platform opens the way for enhanced levels of Quality of Service (QoS), with respect to reliability, availability and latency, in addition to facilitating interoperability and power reduction compared to existing platforms. The small form factor also allows potential of integration with other mobile platforms including smart phones.

A novel and miniaturized 433/868MHz multi-band wireless sensor platform for body sensor network applications

Body Sensor Network (BSN) technology is seeing a rapid emergence in application areas such as health, fitness and sports monitoring. Current BSN wireless sensors typically operate on a single frequency band (e.g. utilizing the IEEE 802.15.4 standard that operates at 2.45GHz) employing a single radio transceiver for wireless communications. This allows a simple wireless architecture to be realized with low cost and power consumption. However, network congestion/failure can create potential issues in terms of reliability of data transfer, quality-of-service (QOS) and data throughput for the sensor. These issues can be especially critical in healthcare monitoring applications where data availability and integrity is crucial. The addition of more than one radio has the potential to address some of the above issues. For example, multi-radio implementations can allow access to more than one network, providing increased coverage and data processing as well as improved interoperability between networks. A small number of multi-radio wireless sensor solutions exist at present but require the use of more than one radio transceiver devices to achieve multi-band operation. This paper presents the design of a novel prototype multi-radio hardware platform that uses a single radio transceiver. The proposed design allows multi-band operation in the 433/868MHz ISM bands and this, together with its low complexity and small form factor, make it suitable for a wide range of BSN applications.

Microneedle platform for continuous monitoring of biomarkers in interstitial fluid

Science Foundation Ireland (CSET - Centre for Science, Engineering and Technology, Grant No. 07/CE/11147)

Explorations in a meaning making system: Kerry as an entrepreneurial platform and the equine sector as a cluster

This Portfolio is about the changes that can be supported and achieved through transformational education that impacts on personal, professional and organisational levels. Having lived through an era of tremendous change over the second half of the twentieth century and into the twenty-first the author has a great drawing board to contemplate in the context of professional career experience as an engineer. The ability to engage in ‘subject-object’ separation is the means by which Kegan (1994, 2009) explains that transformation takes place and the Essays in this Portfolio aim to support and bring about such change. Exploration of aspects of ‘Kerry’ is the material selected to both challenge support change in the way of knowing from being subject to certain information and knowledge that to being able to consider it more objectively. The task of being able to distance judgement about the economy and economic development of Kerry was facilitated by various readings around of a number of key thinkers including Kegan, Drucker, Porter and Penrose. The central themes of Kerry or the potential for economic development are built into each Essay. Essay One focuses on reflections of Kerry life - on Kerry people within and without Kerry - and events as they affected understandings of how people related to and worked with one another. These reflections formed the basis for transformational goals identified which required a shift from an engineering mindset to encompass an economics-based view. In Essay Two knowledge of economic concepts is developed by exploring the writings of Drucker, Penrose, and Porter with pertinence to considering economic development generally, and for Kerry in particular in the form of an ‘entrepreneurial platform’. The concepts and theories were the basis of explorations presented in Essays Three and Four. Essay Three focuses on Kerry’s potential for economic development give its current economic profile and includes results from interviews with selected businesses. Essay Four is an exercise in the application of Porter’s ‘Cluster’ concept to the equine sector.