Estudo de anomalias eletromagnéticas de um condutor tabular vertical sob camadas parcialmente condutiva em multifrequência e multiseparação através de modelamento analógico

A resposta eletromagnética (EM) de um corpo condutivo envolvido por uma zona parcialmente condutiva, torna-se bastante diferente daquela de um corpo condutivo em um meio altamente resistivo. As zonas parcialmente condutivas, como por exemplo, rocha encaixante, halo de sulfetos disseminados ou manto de intemperismo, que envolvem o corpo condutivo, afetam a resposta EM de diferentes maneiras, dependendo de suas características físicas e geométricas e, em particular, do sistema de prospecção EM utilizado. Neste trabalho em modelamento analógico, foi feita uma análise de anomalias EM provocadas por corpos condutivos tabulares verticais sob manto de intemperismo, em levantamentos terrestres para diferentes sistemas de bobinas - horizontal coplanar, vertical coplanar e vertical coaxial - em oito frequências na faixa de 250 Hz a 35 kHz e separações entre as bobinas de 0,15; 0,20 e 0,25m. O manto de intemperismo foi simulado por folhas de aço finas dispostas horizontalmente e o corpo condutor principal por folhas de alumínio finas colocadas verticalmente. As dimensões das folhas foram determinadas de acordo com as condições de modelamento para o plano e o semi-plano. Foram utilizados três corpos e três mantos com diferentes espessuras e condutividades, simulando, deste modo, diversas situações geológicas. Os resultados mostraram que cada sistema de bobinas é afetado diferentemente pela presença do manto de intemperismo. Para a análise dos resultados foi plotado um conjunto de diagramas considerando os valores pico-a-pico das anomalias em fase e em quadratura. Um outro conjunto de diagramas mostra as amplitudes máximas em fase, que ocorrem quando a componente em quadratura se anula em uma frequência relativamente baixa para um conjunto de corpo-manto, e as amplitudes máximas em quadratura, que ocorrem quando a resposta em fase atinge um mínimo próximo de zero, em frequências relativamente altas. Com isto foi possível conhecer a faixa de frequências para cada sistema de bobinas, onde a resposta EM se encontra o mínimo afetada pela presença do manto de intemperismo. A maior amplitude na resposta é obtida no sistema horizontal coplanar e a menor no sistema vertical coplanar. Um aumento na separação entre as bobinas é acompanhado por um deslocamento da anomalia para baixas frequências. A faixa de frequências, onde a presença do manto tem pouca influência na resposta do corpo condutivo, e maior para o sistema vertical coaxial e menor para o sistema horizontal coplanar. Esses resultados dão uma luz para o conhecimento da posição e da largura da banda de frequências utilizável, assim como as melhores separações entre transmissor-receptor, para auxiliar no planejamento de sistemas de prospecção EM, de modo que a resposta fique o mais livre possível de sinais indesejáveis, tais como os causados pela presença do manto de intemperismo.

Modelamento analógico de polarização induzida para corpos cilíndricos e tabulares

O método de polarização induzida, consagrado como ferramenta de prospecção de sulfetos metálicos e indiretamente, do ouro em associações polimetálicas, vem crescendo em outras aplicações como prospecção de águas subterrâneas, investigações de interesse à Engenharia Civil e ao uso de ocupação do solo. Neste trabalho, inicialmente, faz-se uma visualização geral do método IP, suas aplicabilidades, metodologia de trabalhos, arranjos de campo, fundamentos teóricos, vantagens e desvantagens etc. O objetivo principal, entretanto, é o modelamento analógico em laboratório, no sentido de simular-se as condições encontradas na natureza. Para tanto, utilizou-se de modelos geométricos simples, cilindros e placas. Na confecção destes modelos, utilizou-se cimento, areia quartzitica e grafita. Como a grafita apresenta um intenso fenômeno IP, variou-se o teor de grafita contido nos modelos. Assim, para diferentes formas e medidas dos modelos, variou-se também o conteúdo de partículas polarizáveis. As medidas foram feitas no sentido de verificar-se o comportamento da resposta IP quanto a forma, conteúdo de grafita, profundidade e direção do modelo estudado.

Processo de destilação para redução de contaminação por carbamato de etila em bebidas alcoólicas

Contamination of Brazilian sugar-cane rum by ethyl carbamate, a potentially carcinogenic substance, is considered an obstacle to export of the beverage. Copper is involved in ethyl-carbamate-formation reactions, and the replacement thereof by stainless steel in distillation equipment, with the aim of preventing the formation of said compound, results in a beverage of poor sensory quality owing to the presence of dimethyl sulphide. A reduction in the concentration of sulphurated compounds in the final product may be achieved by the placing of a copper device (Patent No. 8206688) inside the dome of a stainless-steel alembic. It is therefore appropriate to verify the efficiency of using other forms of catalysts that, in addition to reducing ethyl-carbamate levels, are able, likewise, to trigger other catalytic actions that allow the production of a distillate of good sensory quality. Silver is the noble metal most used in industry and, on account of the catalytic properties thereof, it is ideal for use as a catalyst in oxidation reactions. The subject matter of the present invention comprises a method involving the use of silver in the distillation of alcoholic beverages, such as sugar-cane rum, which reduces ethyl-carbamate contamination of the end-product.

Obtenção e avaliação de mutantes de Acidithiobacillus ferrooxidans quanto à capacidade de lixiviar minérios de cobre

Pós-graduação em Biotecnologia - IQ

Tratamento de efluente de curtume por biofiltro aerado Submerso pré-tratado com microfiltro de membrana

Pós-graduação em Engenharia Civil - FEIS

Análise estrutural e microtectônica da inflexão do jordino e depósitos de ouro associados no greenstone belt de Pilar de Goiás

The study area is included in the geological context of the Goias Median Massif, a region where there are associations of Archean granite-gneiss complex (Block Moquém) and a Paleoproterozoic metavolcano-sedimentary sequence ( Pilar greenstone belt ). At the south of area, the greenstone sequence is partially overlain by Neopreoterozoic metasediments of the Araxá Group. The lithostratigraphic units of the Pilar greenstone belt define a shift from about N30W direction (north of the deposit) to N60 and 70W in the region south of the Jordino deposit, where are truncated by the Araxá Group rocks. Mineralogical associations described in this paper allow to indicate that the regional metamorphism that affected the rocks of the greenstone belt and Araxá Group, in the mapped area, reached the upper greenschist facies (garnet zone). Data obtained during mapping and by microtectonics analysis allow to indicate the existence of at least four deformational events that acted on the rocks of the Guarinos greenstone belt and Araxá Group, represented by the phases called Dn-1, Dn, Dn + 1 and Dn+2. It was observed that the pattern of sulphide porfitoblasts in mineralized levels is similar to garnet, biotite and muscovite porfiroblasts (tardi to post Dn) that marks the metamorphic peak of the area

Análise da viabilidade do uso de biogás gerado a partir de dejetos bovinos em microturbinas para fins de geração, cogeração e trigeração de energia

The use of digesters has become an important alternative for the proper disposal of organic agricultural wastes, serving as a solution to some environmental and health problems. Furthermore, the process of digestion provides commercially valuable by products such as biogas and bio fertilizer. The generation of biogas from agricultural waste, and its use in power generation systems has aroused great interest in rural areas because it enables supply in whole or in large part the energy demand of ownership by reducing production costs. The advent of technology has brought new forms of energy conversion of biogas, as the use of micro turbines specifies to be fuelled with biogas derived from the decomposition of organic matter in digesters, since it has a low level of methane in its composition, and high degree of impurities such as hydrogen sulphide, which are harmful to equipment and reduce the calorific value of biogas. The use of micro turbines behind other advantages like low emissions, great fuel flexibility and low maintenance. This paper presents an analysis of the feasibility of using biogas generated from cattle manure in micro turbines to generate electricity. Behind also an assessment of the energy potential that each animal has on various uses of biogas, and forms of energy recovery from the exhaust gases of the micro turbine. Also conducts an evaluation of the energy savings that the use of biogas aggregates properties.

Integração de dados geofísicos e geológicos na caracterização morfológica de ocorrência de cobre na borda norte da Bacia do Camaquã (RS)

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Dissolução redutiva de minério de ferro por Acidithiobacillus ferrooxidans para a recuperação de metais de interesse econômico

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

The Bologna Stone: history's first persistent luminescent material

In 1603, the Italian shoemaker Vincenzo Cascariolo found that a stone (baryte) from the outskirts of Bologna emitted light in the dark without any external excitation source. However, the calcination of the baryte was needed prior to this observation. The stone later named as the Bologna Stone was among the first luminescent materials and the first documented material to show persistent luminescence. The mechanism behind the persistent emission in this material has remained a mystery ever since. In this work, the Bologna Stone (BaS) was prepared from the natural baryte (Bologna, Italy) used by Cascariolo. Its properties, e. g. impurities (dopants) and their valences, luminescence, persistent luminescence and trap structure, were compared to those of the pure BaS materials doped with different (transition) metals (Cu, Ag, Pb) known to yield strong luminescence. The work was carried out by using different methods (XANES, TL, VUV-UV-vis luminescence, TGA-DTA, XPD). A plausible mechanism for the persistent luminescence from the Bologna Stone with Cu+ as the emitting species was constructed based on the results obtained. The puzzle of the Bologna Stone can thus be considered as resolved after some 400 years of studies.

Phytostabilisation : use of wetland plants to treat mine tailings

Mine tailings can be rich in sulphide minerals and may form acid mine drainage (AMD) through reaction with atmospheric oxygen and water. AMD contains elevated levels of metals and arsenic (As) that could be harmful to animals and plants. An oxygen-consuming layer of organic material and plants on top of water-covered tailings would probably reduce oxygen penetration into the tailings and thus reduce the formation of AMD. However, wetland plants have the ability to release oxygen through the roots and could thereby increase the solubility of metals and As. These elements are released into the drainage water, taken up and accumulated in the plant roots, or translocated to the shoots. The aim was to examine the effects of plant establishment on water-covered mine tailings by answering following questions: A) Is plant establishment on water-covered mine tailings possible? B) What are the metal and As uptake and translocation properties of these plants? C) How do plants affect metal and As release from mine tailings, and which are the mechanisms involved? Carex rostrata Stokes, Eriophorum angustifolium Honck., E. scheuchzeri Hoppe, Phragmites australis (Cav.) Steud., Salix phylicifolia L. and S. borealis Fr. were used as test plants. Influences of plants on the release of As, Cd, Cu, Pb, Zn and in some cases Fe in the drainage water, and plant element uptake were studied in greenhouse experiments and in the field. The results obtained demonstrate that plant establishment are possible on water-covered unweathered mine tailings, and a suitable amendment was found to be sewage sludge. On acidic, weathered tailings, a pH increasing substance such as ashes should be added to improve plant establishment. The metal and As concentrations of the plant tissue were found to be generally higher in roots than in shoots. The uptake was dependent on the metal and As concentrations of the tailings and the release of organic acids from plant roots may have influenced the uptake. The metal release from tailings into the drainage water caused by E. angustifolium was found to depend greatly on the age and chemical properties of the tailings. However, no effects of E. angustifolium on As release was found. Water from old sulphide-, metal- and As-rich tailings with low buffering capacity were positively affected by E. angustifolium by causing higher pH and lower metal concentrations. In tailings with relatively low sulphide, metal and As contents combined with a low buffering capacity, plants had the opposite impact, i.e. a reduction in pH and elevated metal levels of the drainage water. The total release of metal and As from the tailings, i.e. drainage water together with the contents in shoots and roots, was found to be similar for C. rostrata, E. angustifolium and P. australis, except for Fe and As, where the release was highest for P. australis. The differences in metal and As release from mine tailings were mainly found to be due to the release of O2 from the roots, which changes the redox potential. Release of organic acids from the roots slightly decreased the pH, although did not have any particular influence on the release of metal and As. In conclusion, as shown here, phytostabilisation may be a successful technique for remediation of mine tailings with high element and sulphide levels, and low buffering capacity.

Sedimentology and tectonic history of late Archaean sedimentary successions in Zimbabwe

ZusammenfassungSpätarchaische Sedimentgesteine (ca. 2,65 Milliarden Jahre alt) wurden in Grünsteingürteln des Simbabwe Kratons untersucht. In dem Belingwe Grünsteingürtel ist granitoides Grundgebirge von einer allochthonen Einheit aus vulkanischen Gesteinen und Vorlandbeckensedimenten überlagert. Die sedimentäre Abfolge besteht aus Flachwasserkalken und Turbiditen. Unterschiedliche Faziestypen der Kalksteine sind in sedimentäre Verflachungszyklen angeordnet. Eustatische Meeresspiegelschwankungen werden als Ursache der zyklischen Sedimentation angenommen. Sedimentologische, geochemische und strukturelle Analysen zeigen die Bedeutung horizontal-tektonischer Prozesse für die Entstehung dieses Grünsteingürtels an.Sedimentgesteine des Midlands Grünsteingürtels lagern zwischen ozeanischen, mafischen Vulkaniten und kontinentalen, granitoiden Gneisen. Die Art der Abfolge sedimentärer Fazies, beginnend mit Turbiditen und überlagert von flachmarinen Schelfsedimenten und alluvialen Ablagerungen, sowie geologische und geochemische Hinweise aus den benachbarten Gesteinsserien lassen auf Ablagerung während der Kollision zwischen einem ozeanischen Plateau/Inselbogen und einem kontinentalen Krustenfragmentes schließen.In dem Bindura-Shamva Grünsteingürtel können zwei Sedimentgesteinseinheiten unterschieden werden, eine alluvial—flachmarine Abfolge und eine tiefmarin—fluviatile Abfolge. Extensionstektonik verursachte wahrscheinlich die Bildung des Sedimentbeckens. Die spätere Phase der Beckenbildung war jedoch ähnlich jener in modernen Vorlandbecken.Schichtparallele Eisensteinhorizonte sind häufig entlang von Sediment-Vulkanit-Kontakten zu finden. Diese Gesteine werden als silifizierte und von Sulfiden imprägnierte Scherzonen interpretiert. Syntektonische hydrothermale Alteration von Gesteinen entlang der Störungszonen führte zur Bildung dieser 'tektonischen Eisensteine'.

Measurement of volatile organic compounds and total OH reactivity in the atmosphere

Volatile organic compounds play a critical role in ozone formation and drive the chemistry of the atmosphere, together with OH radicals. The simplest volatile organic compound methane is a climatologically important greenhouse gas, and plays a key role in regulating water vapour in the stratosphere and hydroxyl radicals in the troposphere. The OH radical is the most important atmospheric oxidant and knowledge of the atmospheric OH sink, together with the OH source and ambient OH concentrations is essential for understanding the oxidative capacity of the atmosphere. Oceanic emission and / or uptake of methanol, acetone, acetaldehyde, isoprene and dimethyl sulphide (DMS) was characterized as a function of photosynthetically active radiation (PAR) and a suite of biological parameters, in a mesocosm experiment conducted in the Norwegian fjord. High frequency (ca. 1 minute-1) methane measurements were performed using a gas chromatograph - flame ionization detector (GC-FID) in the boreal forests of Finland and the tropical forests of Suriname. A new on-line method (Comparative Reactivity Method - CRM) was developed to directly measure the total OH reactivity (sink) of ambient air. It was observed that under conditions of high biological activity and a PAR of ~ 450 μmol photons m-2 s-1, the ocean acted as a net source of acetone. However, if either of these criteria was not fulfilled then the ocean acted as a net sink of acetone. This new insight into the biogeochemical cycling of acetone at the ocean-air interface has helped to resolve discrepancies from earlier works such as Jacob et al. (2002) who reported the ocean to be a net acetone source (27 Tg yr-1) and Marandino et al. (2005) who reported the ocean to be a net sink of acetone (- 48 Tg yr-1). The ocean acted as net source of isoprene, DMS and acetaldehyde but net sink of methanol. Based on these findings, it is recommended that compound specific PAR and biological dependency be used for estimating the influence of the global ocean on atmospheric VOC budgets. Methane was observed to accumulate within the nocturnal boundary layer, clearly indicating emissions from the forest ecosystems. There was a remarkable similarity in the time series of the boreal and tropical forest ecosystem. The average of the median mixing ratios during a typical diel cycle were 1.83 μmol mol-1 and 1.74 μmol mol-1 for the boreal forest ecosystem and tropical forest ecosystem respectively. A flux value of (3.62 ± 0.87) x 1011 molecules cm-2 s-1 (or 45.5 ± 11 Tg CH4 yr-1 for global boreal forest area) was derived, which highlights the importance of the boreal forest ecosystem for the global budget of methane (~ 600 Tg yr-1). The newly developed CRM technique has a dynamic range of ~ 4 s-1 to 300 s-1 and accuracy of ± 25 %. The system has been tested and calibrated with several single and mixed hydrocarbon standards showing excellent linearity and accountability with the reactivity of the standards. Field tests at an urban and forest site illustrate the promise of the new method. The results from this study have improved current understanding about VOC emissions and uptake from ocean and forest ecosystems. Moreover, a new technique for directly measuring the total OH reactivity of ambient air has been developed and validated, which will be a valuable addition to the existing suite of atmospheric measurement techniques.

Prokaryotic community structure in ultra-slow spreading Southwest Indian Ridge.

The Southwest Indian Ridge segment that extends between 10° and 16° E has the slowest spreading rate of any other oceanic ridge (about 8.4 mm/year). In 2013 during the expedition ANTXXIX/8 seismology, geology, microbiology, heat flow analyses were carried out. Here, no hydrothermal plumes or black smoker systems were found but the results of the survey allowed to identify areas with peculiar characteristics: Area 1 with higher heat flux bsf; Area 2 where in 2002 the presence of hydrothermal emissions was hypothesized (Bach et al., 2002); Area 3 with anomalies of methane, ammonium, sulphide and dissolved inorganic carbon in pore water sediment profiles, and recovery of fauna vents. All these aspects suggest the presence of a hydrothermal circulation. Using Illumina 16S gene tag, statistical tools and phylogenetic trees, I provided a biological proof of the presence of hydrothermal circulation in this ridge segment. At Area 3, alpha and beta diversity indexes showed similarities with those described for venting microbial communities and about 40-70% of the dominant microbial community was found phylogenetically related to clones isolated hydrothermal-driven environments. Although the majority of chemosynthetic environment related taxa were not classified like autotrophic prokaryotes, some of them are key taxa in support of the presence of hydrothermal circulation, since they are partners of consortia or mediate specific reaction typically described for hydrothermal and seep environments, or are specialized organisms in exploiting labile organic substrates. Concluding, these results are remarkable because support the importance of ultra slow spreading ridge systems in contributing to global geochemical cycles and larval dispersion of vent fauna.

Molybdenum isotope fractionation in pelagic euxinia: Evidence from the modern Black and Baltic Seas

Here we present stable isotope data for vertical profiles of dissolved molybdenum of the modern euxinic water columns of the Black Sea and two deeps of the Baltic Sea. Dissolved molybdenum in all water samples is depleted in salinity-normalized concentration and enriched in the heavy isotope (δ98Mo values up to + 2.9‰) compared to previously published isotope data of sedimentary molybdenum from the same range of water depths. Furthermore, δ98Mo values of all water samples from the Black Sea and anoxic deeps of the Baltic Sea are heavier than open ocean water. The observed isotope fractionation between sediments and the anoxic water column of the Black Sea are in line with the model of thiomolybdates that scavenge to particles under reducing conditions. An extrapolation to a theoretical pure MoS42− solution indicates a fractionation constant between MoS42− and authigenic solid Mo of 0.5 ± 0.3‰. Measured waters with all thiomolybdates coexisting in various proportions show larger but non-linear fractionation. The best explanation for our field observations is Mo scavenging by the thiomolybdates, dominantly — but not exclusively — present in the form of MoS42−. The Mo isotopic compositions of samples from the sediments and anoxic water column of the Baltic Sea are in overall agreement with those of the Black Sea at intermediate depth and corresponding sulphide concentrations. The more dynamic changes of redox conditions in the Baltic deeps complicate the Black Sea-derived relationship between thiomolybdates and Mo isotopic composition. In particular, the occasional flushing/mixing, of the deep waters, affects the corresponding water column and sedimentary data. δ98Mo values of the upper oxic waters of both basins are higher than predicted by mixing models based on salinity variations. The results can be explained by non-conservative behaviour of Mo under suboxic to anoxic conditions in the shallow bottom parts of the basin, most pronounced on the NW shelf of the Black Sea.