Annealing behavior of ferritic-martensitic 9%Cr-ODS-Eurofer steel

Oxide dispersion strengthened ferritic-martensitic steels are potential candidates for applications in future fusion power plants. High creep resistance, good oxidation resistance, reduced neutron activation and microstructural long-term stability at temperatures of about 650-700 degrees C are required in this context. In order to evaluate its thermal stability in the ferritic phase field, samples of the reduced activation ferritic-martensitic 9%Cr-ODS-Eurofer steel were cold rolled to 50% and 80% reductions and further annealed in vacuum from 300 to 800 degrees C for 1 h. The characterization in the annealed state was performed by scanning electron microscopy in the backscattered electron mode, high-resolution electron backscatter diffraction and transmission electron microscopy. Results show that the fine dispersion of Y-based particles (about 10 nm in size) is effective to prevent recrystallization. The low recrystallized volume fraction (<0.1) is associated to the nuclei found at prior grain boundaries and around large M(23)C(6) particles. Static recovery was found to be the predominant softening mechanism of this steel in the investigated temperature range. (c) 2010 Elsevier B.V. All rights reserved.

ANNEALING EFFECTS ON THE MICROSTRUCTURE OF FERRITIC-MARTENSITIC ODS-EUROFER STEEL

Oxide dispersion strengthened (ODS) ferritic/martensitic (FM) steels are promising candidates for structural applications in future fusion power reactors. In order to evaluate the thermal stability of 80% cold-rolled ODS-EUROFER, samples were annealed for 1 h at temperatures up to about 0.9 T(m), where T(m) is the absolute melting point. The characterization of the annealed samples was performed using transmission electron microscopy and electron backscatter diffraction. Results show that static recovery is the main softening mechanism of this steel when annealed below 800 degrees C. The volume fraction of recrystallized grains is quite small (below 0.10). Above 900 degrees C, martensitic transformation takes place causing pronounced hardening. Large M(23)C(6) particles are found at the grain boundaries after tempering at 750 degrees C for 2 h.

Thin titanium oxide films deposited by e-beam evaporation with additional rapid thermal oxidation and annealing for ISFET applications

Titanium oxide (TiO(2)) has been extensively applied in the medical area due to its proved biocompatibility with human cells [1]. This work presents the characterization of titanium oxide thin films as a potential dielectric to be applied in ion sensitive field-effect transistors. The films were obtained by rapid thermal oxidation and annealing (at 300, 600, 960 and 1200 degrees C) of thin titanium films of different thicknesses (5 nm, 10 nm and 20 nm) deposited by e-beam evaporation on silicon wafers. These films were analyzed as-deposited and after annealing in forming gas for 25 min by Ellipsometry, Fourier Transform Infrared Spectroscopy (FTIR), Raman Spectroscopy (RAMAN), Atomic Force Microscopy (AFM), Rutherford Backscattering Spectroscopy (RBS) and Ti-K edge X-ray Absorption Near Edge Structure (XANES). Thin film thickness, roughness, surface grain sizes, refractive indexes and oxygen concentration depend on the oxidation and annealing temperature. Structural characterization showed mainly presence of the crystalline rutile phase, however, other oxides such Ti(2)O(3), an interfacial SiO(2) layer between the dielectric and the substrate and the anatase crystalline phase of TiO(2) films were also identified. Electrical characteristics were obtained by means of I-V and C-V measured curves of Al/Si/TiO(x)/Al capacitors. These curves showed that the films had high dielectric constants between 12 and 33, interface charge density of about 10(10)/cm(2) and leakage current density between 1 and 10(-4) A/cm(2). Field-effect transistors were fabricated in order to analyze I(D) x V(DS) and log I(D) x Bias curves. Early voltage value of -1629 V, R(OUT) value of 215 M Omega and slope of 100 mV/dec were determined for the 20 nm TiO(x) film thermally treated at 960 degrees C. (C) 2009 Elsevier B.V. All rights reserved.

Identification by computer-simulated RFLP of phytoplasmas associated with eggplant giant calyx representative of two subgroups, a lineage of 16SrIII-J and the new subgroup 16SrIII-U

Symptoms resembling giant calyx, a graft-transmissible disease, were observed on 1-5% of eggplant (aubergine; Solanum melongena L.) plants in production fields in Sao Paulo state, Brazil. Phytoplasmas were detected in 1 2 of 1 2 samples from symptomatic plants that were analysed by a nested PCR assay employing 16S rRNA gene primers R16mF2/R16mR1 followed by R16F2n/R16R2. RFLP analysis of the resulting rRNA gene products (1.2 kb) indicated that all plants contained similar phytoplasmas, each closely resembling strains previously classified as members of RFLP group 16SrIII (X-disease group). Virtual RFLP and phylogenetic analyses of sequences derived from PCR products identified phytoplasmas infecting eggplant crops grown in Piracicaba as a lineage of the subgroup 16SrIII-J, whereas phytoplasmas detected in plants grown in Braganca Paulista were tentatively classified as members of a novel subgroup 16SrIII-U. These findings confirm eggplant as a new host of group 16SrIII-J phytoplasmas and extend the known diversity of strains belonging to this group in Brazil.

Viability of Lactobacillus acidophilus in synbiotic guava mousses and its survival under in vitro simulated gastrointestinal conditions

The effects of refrigeration, freezing and substitution of milk fat by inulin and whey protein concentrate (WPC) on Lactobacillus acidophilus La-5 viability and resistance to gastric and enteric simulated conditions in synbiotic guava mousses effects were investigated. Refrigerated mousses supplemented with WPC presented the best probiotic viability. ranging from 7.77 to 6.24 log cfu/g during 28 days of storage. The highest probiotic populations, above 7.45 log cfu/g, were observed for all frozen mousses during 112 days of storage. Decreased L acidophilus survival during the in vitro gastrointestinal simulation was observed both for refrigerated and frozen mousses. Nonetheless, for the refrigerated mousses, the addition of inulin enhanced the probiotic survival during the in vitro assays in the first week of storage. L acidophilus survival in simulated gastrointestinal fluids was also improved through freezing. The frozen storage may be used to provide increased shelf-life for synbiotic guava mousses. Even though the protective effect of inulin and WPC on the probiotic microorganism tested was shown to be more specific for the refrigerated products, the partial replacement of milk fat by these ingredients may also help, as it improves the nutritional value of mousses in both storage conditions. (C) 2009 Elsevier B.V. All rights reserved.

Annealing of ion implanted gallium nitride

In this paper, we examine Si and Te ion implant damage removal in GaN as a function of implantation dose, and implantation and annealing temperature. Transmission electron microscopy shows that amorphous layers, which can result from high-dose implantation, recrystallize between 800 and 1100 °C to very defective polycrystalline material. Lower-dose implants (down to 5 × 1013 cm – 2), which are not amorphous but defective after implantation, also anneal poorly up to 1100 °C, leaving a coarse network of extended defects. Despite such disorder, a high fraction of Te is found to be substitutional in GaN both following implantation and after annealing. Furthermore, although elevated-temperature implants result in less disorder after implantation, this damage is also impossible to anneal out completely by 1100 °C. The implications of this study are that considerably higher annealing temperatures will be needed to remove damage for optimum electrical properties. ©1998 American Institute of Physics.

Cannabidiol Reduces the Anxiety Induced by Simulated Public Speaking in Treatment-Naive Social Phobia Patients

Generalized Social Anxiety Disorder (SAD) is one of the most common anxiety conditions with impairment in social life. Cannabidiol (CBD), one major non-psychotomimetic compound of the cannabis sativa plant, has shown anxiolytic effects both in humans and in animals. This preliminary study aimed to compare the effects of a simulation public speaking test (SPST) on healthy control (HC) patients and treatment-naive SAD patients who received a single dose of CBD or placebo. A total of 24 never-treated patients with SAD were allocated to receive either CBD (600 mg; n = 12) or placebo (placebo; n = 12) in a double-blind randomized design 1 h and a half before the test. The same number of HC (n = 12) performed the SPST without receiving any medication. Each volunteer participated in only one experimental session in a double-blind procedure. Subjective ratings on the Visual Analogue Mood Scale (VAMS) and Negative Self-Statement scale (SSPS-N) and physiological measures (blood pressure, heart rate, and skin conductance) were measured at six different time points during the SPST. The results were submitted to a repeated-measures analysis of variance. Pretreatment with CBD significantly reduced anxiety, cognitive impairment and discomfort in their speech performance, and significantly decreased alert in their anticipatory speech. The placebo group presented higher anxiety, cognitive impairment, discomfort, and alert levels when compared with the control group as assessed with the VAMS. The SSPS-N scores evidenced significant increases during the testing of placebo group that was almost abolished in the CBD group. No significant differences were observed between CBD and HC in SSPS-N scores or in the cognitive impairment, discomfort, and alert factors of VAMS. The increase in anxiety induced by the SPST on subjects with SAD was reduced with the use of CBD, resulting in a similar response as the HC. Neuropsychopharmacology (2011) 36, 1219-1226; doi: 10.1038/npp.2011.6; published online 9 February 2011

Escitalopram prolonged fear induced by simulated public speaking and released hypothalamic-pituitary-adrenal axis activation

Simulated public speaking (SPS) test is sensitive to drugs that interfere with serotonin-mediated neurotransmission and is supposed to recruit neural systems involved in panic disorder. The study was aimed at evaluating the effects of escitalopram, the most selective serotonin-selective reuptake inhibitor available, in SPS. Healthy males received, in a double-blind, randomized design, placebo (n = 12), 10 (n = 17) or 20 (n = 14) mg of escitalopram 2 hours before the test. Behavioural, autonomic and neuroendocrine measures were assessed. Both doses of escitalopram did not produce any effect before or during the speech but prolonged the fear induced by SPS. The test itself did not significantly change cortisol and prolactin levels but under the higher dose of escitalopram, cortisol and prolactin increased immediately after SPS. This fear-enhancing effect of escitalopram agrees with previously reported results with less selective serotonin reuptake inhibitors and the receptor antagonist ritanserin, indicating that serotonin inhibits the fear of speaking in public.

The role of surface sealants in the roughness of composites after a simulated toothbrushing test

Objectives: To evaluate the influence of two surface sealants (BisCover/Single Bond) and three application techniques (unsealed/conventional/co-polymerization) on the roughness of two composites (Filtek Z250/Z350) after the toothbrushing test. Methods: Seventy-two rectangular specimens (5 mm x 10 mm x 3 mm) were fabricated and assigned into 12 groups (n = 6). Each sample was subjected to three random roughness readings at baseline, after 100,000 (intermediate), and 200,000 (final) toothbrushing strokes. Roughness (R) at each stage was obtained by the arithmetic mean of the reading of each specimen. Sealant removal was qualitatively examined (optical microscope) and classified into scores (0-3). Data were analyzed by Student`s paired t-test, two-way ANOVA/Tukey`s test, and by Wilcoxon, Kruskal-Wallis and Miller`s test (alpha = 0.05). Results: Z250 groups at baseline did not differ statistically from each other. Unsealed Z350 at baseline had lower R values. All the unsealed groups presented gradual decrease in R from baseline to final brushing. From baseline to the inter-mediate stage, Z250 co-polymerized groups presented a significant reduction in R (score 3). Conventionally sealed groups had no significant changes in R (scores 2-0.8). From baseline to the intermediate stage, the conventionally sealed Z350 Single Bond group had an increase in R (score 1.5). In the final stage, all the conventionally sealed groups presented a reduction in R (scores 0.7-0). Co-polymerized Single Bond groups had a significant reduction in R (scores 2.5-2.7), and co-polymerized BisCover groups an increase in R (scores 2.8-3). Conclusions: At any brushing stage, sealed composites presented superior performance when compared with unsealed composites. (C) 2009 Elsevier Ltd. All rights reserved.

Sodium bicarbonate solution as an anti-erosive agent against simulated endogenous erosion

This study investigated whether sodium bicarbonate solution, applied on enamel previously exposed to a simulated intrinsic acid, can control dental erosion. Volunteers wore palatal devices containing enamel slabs, which were exposed twice daily extra-orally to hydrochloric acid (0.01 M, pH 2) for 2 min. Immediately afterwards, the palatal devices were re-inserted in the mouth and volunteers rinsed their oral cavity with a sodium bicarbonate solution or deionized water for 60 s. After the washout period, the palatal devices were refilled with a new set of specimens and participants were crossed over to receive the alternate rinse solution. The surface loss and surface microhardness (SMH) of specimens were assessed. The surface loss of eroded enamel rinsed with a sodium bicarbonate solution was significantly lower than the surface loss of eroded enamel rinsed with deionized water. There were no differences between treatments with sodium bicarbonate and deionized water for SMH measurements. Regardless of the solution used as an oral rinse, eroded enamel showed lower SMH than uneroded specimens. Rinsing with a sodium bicarbonate solution after simulated endogenous erosive challenge controlled enamel surface loss but did not alter the microhardness.

Effect of simulated masticatory loading on the retention of stud attachments for implant overdentures

P>This study assessed the effect of simulated mastication on the retention of two stud attachment systems for 2-implants overdentures. Sixteen specimens, each simulating an edentulous ridge with implants and an overdenture were divided into two groups, according to the attachment system: Group I (Nobel Biocare ball-socket attachments) and Group II (Locator attachments). Retention forces were measured before and after 400 000 simulated masticatory loads in a customised device. Data were compared by two-way anova followed by Bonferroni test (alpha = 0 center dot 05). Group I presented significantly lower retention forces (Newtons) than Group II at baseline (10 center dot 6 +/- 3 center dot 6 and 66 center dot 4 +/- 16 center dot 0, respectively). However, differences were not significant after 400 000 loads (7 center dot 9 +/- 4 center dot 3 and 21 center dot 6 +/- 17 center dot 0). The number of cycles did not influence the measurements in Group I, whereas a non-linear descending curve was found for Group II. It was concluded that simulated mastication resulted in minor changes for the ball attachment tested. Nevertheless, it reduced the retention of Locator attachments to 40% of the baseline values, what suggests that mastication is a major factor associated with maintenance needs for this system.

Amylases in enzyme detergents and their effects on a simulated long-life dairy dessert

Enzyme detergents used in the food industry contain proteinase as the major enzyme but amylase may be present, either by design or inadvertently. Three commercial enzyme detergents and 3 enzyme preparations used in detergents were assayed for alpha-amylase activity by the Ceralpha method using the Megazyme kits. The amylase activities of the detergents varied from 3.2x 10(-6) to 32x 10(-6) mumoles ml(-1) h(-1) while the enzyme preparations had much higher activities ranging from 0.05 to 8.06 mumoles ml(-1) h(-1). When added aseptically to a simulated dairy dessert (2% starch solution) and stored for 42 days, the enzyme detergents caused an increase in viscosity; enzyme preparations at low concentrations caused an initial increase in viscosity followed by a decrease; and enzyme preparations at high concentrations caused an immediate decrease in viscosity. The increase in viscosity corresponded to formation of a distinct network of starch granules while the decrease in viscosity was characterised by a marked decrease in size of the granules and little or no network of granules. Decreases in viscosity corresponded to increases in reducing sugars but samples which increased in viscosity showed no measurable reducing sugars. The amylase activity in all sources was destroyed by heating at 75degreesC for 15 min at pH 1.8.

Activation energy distribution of thermal annealing of a bituminous coal

A bituminous coal was pyrolyzed in a nitrogen stream in an entrained flow reactor at various temperatures from 700 to 1475 degreesC. Char samples were collected at different positions along the reactor. Each collected sample was oxidized nonisothermally in a TGA for reactivity determination. The reactivity of the coal char was found to decrease rapidly with residence time until 0.5 s, after which it decreased only slightly. On the bases of the reactivity data at various temperatures, a new approach was utilized to obtaining the true activation energy distribution function for thermal annealing without the assumption of any distribution function form or a constant preexponential factor. It appears that the true activation energy distribution function consists of two separate parts corresponding to different temperature ranges, suggesting different mechanisms in different temperature ranges. Partially burnt coal chars were also collected along the reactor when the coal was oxidized in air at various temperatures from 700 to 1475 degreesC. The collected samples were analyzed for the residual carbon content and the specific reaction rate was estimated. The characteristic time of thermal deactivation was compared with that of oxidation under realistic conditions. The characteristic times were found to be close to each other, indicating the importance of thermal deactivation during combustion of the coal studied.

A elaboração e instituição do currículo mínimo de matemática no Rio de Janeiro

O currículo traz subjacente a si, as ideias de seu tempo, o olhar de sua sociedade para questões humanas e outras tacitamente políticas. Traz em seu escopo toda uma trama de heranças históricas e a marca pessoal daqueles que se dedicaram a sua construção. E desta forma, analisar as tramas de um currículo de matemática é muito mais que olhar uma sequência de conteúdos linearmente organizados. É, sobretudo, entender, que aquela construção foi tecida de forma a sustentar um corpo de ideias que diz sobre seu tempo. Esta pesquisa evidenciou o processo de elaboração e instituição do currículo mínimo pela Seeduc/RJ e trouxe questionamentos e inquietações de naturezas cognitivas e sociais. Uma primeira inquietação concerne ao descarte de conteúdos do currículo anterior, que configura agora, este novo currículo. Esse processo de elaboração e instituição refletiu a inexistência de diálogo entre os diversos segmentos sociais e profissionais do campo educacional. Interesses governamentais interferiram diretamente nos educacionais, subtraindo a democracia das ações de políticas públicas implementadas. Ficou evidente que não houve clareza conceitual quando dessa e em contraste até mesmo com propostas nacionais e a legislação vigente. Através do Currículo Mínimo buscou-se unificar toda a rede de ensino da Seeduc/RJ, dentro de uma perspectiva academicista limitada, desconsiderando as especificidades locais e de cada grupo. Desta forma, foi desconsiderada a dialética educacional e a retórica da matemática enquanto disciplina acadêmica, que é uma forma particular da relação social. O processo instituído evidencia uma visão de professores passivos e alunos considerados mínimos.

A matemática na constituição de um currículo integrado : possibilidades e desafios para o ensino médio e a educação profissional de jovens e adultos

O universo que circunda a Educação de Jovens e Adultos nos sensibiliza e nos provoca. Observar que estes alunos e alunas estão em busca de conquistas e sonhos que não puderam se concretizar quando foram gerados nos impulsiona a conduzir esta pesquisa com seriedade e esperança. Este estudo investigou que conhecimentos matemáticos utilizados por professores do Curso Técnico em Metalurgia Integrado ao Ensino Médio na modalidade de Educação de Jovens e Adultos. Influenciam diálogos entre matemática e outras disciplinas do curso considerando a perspectiva da formação integral dos estudantes. Assim, nos propomos a analisar conhecimentos matemáticos que estão presentes em ações e materiais didáticos utilizados por professores em diferentes disciplinas do Curso Técnico em Metalurgia Integrado ao Ensino Médio na modalidade de Educação de Jovens e Adultos. No intuito de responder a questão proposta e alcançar os objetivos expostos, este estudo torna-se mais relevante por estar diretamente envolvido no processo de consolidação do Programa Nacional de Integração da Educação Profissional com a Educação Básica na Modalidade de Educação de Jovens e Adultos – PROEJA do Curso de Metalurgia ofertado pelo IFES/Vitória, pautado na idealização de integração do seu currículo. Portanto, discutir o projeto de integração curricular que norteia o PROEJA tornou-se uma meta em movimento dessa investigação. Nesta direção, observamos o reflexo de como as práticas e materiais didáticos utilizados por professores, que atuam nesta modalidade, puderam contribuir para discussões que nos ajudaram na compreensão do processo de ensino e aprendizagem dos educandos participantes, com vistas ao desenvolvimento no trabalho ou na formação profissional, como na constituição de conhecimentos científicos, escolares/tecnológicos e culturais. Optamos por direcionar a reflexão teórica deste capítulo em conceitos específicos. Assim, ao tratar da Educação de Jovens e Adultos seremos conduzidos pelos estudos e pesquisas de Paulo Freire (1996, 2000, 2005), Maria da Conceição Fonseca (2007) e Jane Paiva (2009); ao direcionarmos para a Teoria do Ensino Integrado e a Educação Profissional faremos uso dos estudos de Gaudêncio Frigotto (2010) e Marise Ramos (2010); quanto às discussões que refletem acerca da Educação Matemática Critica recorremos às ideias de Ole Skovsmose (2001, 2007).