985 resultados para Roma-Historia-S. VII-V a. de C.
Resumo:
Amorphous and crystalline sputtered boron carbide thin films have a very high hardness even surpassing that of bulk crystalline boron carbide (≈41 GPa). However, magnetron sputtered B-C films have high friction coefficients (C.o.F) which limit their industrial application. Nanopatterning of materials surfaces has been proposed as a solution to decrease the C.o.F. The contact area of the nanopatterned surfaces is decreased due to the nanometre size of the asperities which results in a significant reduction of adhesion and friction. In the present work, the surface of amorphous and polycrystalline B-C thin films deposited by magnetron sputtering was nanopatterned using infrared femtosecond laser radiation. Successive parallel laser tracks 10 μm apart were overlapped in order to obtain a processed area of about 3 mm2. Sinusoidal-like undulations with the same spatial period as the laser tracks were formed on the surface of the amorphous boron carbide films after laser processing. The undulations amplitude increases with increasing laser fluence. The formation of undulations with a 10 μm period was also observed on the surface of the crystalline boron carbide film processed with a pulse energy of 72 μJ. The amplitude of the undulations is about 10 times higher than in the amorphous films processed at the same pulse energy due to the higher roughness of the films and consequent increase in laser radiation absorption. LIPSS formation on the surface of the films was achieved for the three B-C films under study. However, LIPSS are formed under different circumstances. Processing of the amorphous films at low fluence (72 μJ) results in LIPSS formation only on localized spots on the film surface. LIPSS formation was also observed on the top of the undulations formed after laser processing with 78 μJ of the amorphous film deposited at 800 °C. Finally, large-area homogeneous LIPSS coverage of the boron carbide crystalline films surface was achieved within a large range of laser fluences although holes are also formed at higher laser fluences.
Resumo:
The paper reports viscosity measurements of compressed liquid dipropyl (DPA) and dibutyl (DBA) adipates obtained with two vibrating wire sensors developed in our group. The vibrating wire instruments were operated in the forced oscillation, or steady-state mode. The viscosity measurements of DPA were carried out in a range of pressures up to 18. MPa and temperatures from (303 to 333). K, and DBA up to 65. MPa and temperature from (303 to 373). K, covering a total range of viscosities from (1.3 to 8.3). mPa. s. The required density data of the liquid samples were obtained in our laboratory using an Anton Paar vibrating tube densimeter and were reported in a previous paper. The viscosity results were correlated with density, using a modified hard-spheres scheme. The root mean square deviation of the data from the correlation is less than (0.21 and 0.32)% and the maximum absolute relative deviations are within (0.43 and 0.81)%, for DPA and DBA respectively. No data for the viscosity of both adipates could be found in the literature. Independent viscosity measurements were also performed, at atmospheric pressure, using an Ubbelohde capillary in order to compare with the vibrating wire results. The expanded uncertainty of these results is estimated as ±1.5% at a 95% confidence level. The two data sets agree within the uncertainty of both methods. © 2015 Published by Elsevier B.V.
Resumo:
The aim of the present study was to investigate the detection percentage of tuberculosis among patients that are respiratory symptomatic (TB suspects). In this work, we present the preliminary results of research carried out at "Hospital das ClÃnicas de Teresópolis Costantino Ottaviano da Fundação Educacional Serra dos Órgãos (FESO)" from November 2003 to April 2004. Among the 40 respiratory symptomatic individuals identified and referred to the Tuberculosis Control Program in Teresópolis, two (5.0%) were characterized as smear-positive. These results confirm reports in the literature and underscore the need for and importance of this strategy.
Resumo:
2009
Resumo:
2016
Resumo:
La presenza di imponenti ruderi antichi a Palazzo Pignano era già conosciuta nel 1600, mentre per affrontare in modo scientifico il ritrovamento si dovette aspettare fino al 1963, con i radicali restauri all’interno della pieve protoromanica di San Martino: sotto la pieve fu rinvenuto un edificio rotondo a pianta centrale, e nella zona retrostante alla Pieve verso est furono scoperti, fra il 1969 e 1972, i resti della grandiosa Villa che oggi trattiamo. Vi fu una stasi nelle ricerche tra il 1972 e il 1977, quando fu eseguita una serie di sondaggi per definire le dimensioni e le caratteristiche del complesso abitativo. Nel 1988 uno scavo stratigrafico lungo il lato sud della Chiesa ha permesso di individuare una vasca battesimale a immersione. Tra gli anni 1999 e 2001 una campagna di rilievi e prospezioni con magnetometro Fluxgate ha permesso di precisare le varie fasi di vita della Villa: una ristrutturazione importante nella prima metà del V sec. d.C.; e poi l’insediamento nella zona della villa già in abbandono di capanne e sepolture, databili genericamente in un momento altomedioevale.
Resumo:
This paper presents an on-board bidirectional battery charger for Electric Vehicles (EVs), which operates in three different modes: Grid-to- Vehicle (G2V), Vehicle-to-Grid (V2G), and Vehicle-to-Home (V2H). Through these three operation modes, using bidirectional communications based on Information and Communication Technologies (ICT), it will be possible to exchange data between the EV driver and the future smart grids. This collaboration with the smart grids will strengthen the collective awareness systems, contributing to solve and organize issues related with energy resources and power grids. This paper presents the preliminary studies that results from a PhD work related with bidirectional battery chargers for EVs. Thus, in this paper is described the topology of the on-board bidirectional battery charger and the control algorithms for the three operation modes. To validate the topology it was developed a laboratory prototype, and were obtained experimental results for the three operation modes.
Resumo:
This paper presents a new approach of pre-defined profiles, based in different voltage and current values, to control the charging and discharging processes of batteries in order to assess their performance. This new approach was implemented in a prototype that was specially developed for such purpose. This prototype is a smart power electronics platform that allows to perform batteries analysis and to control the charging and discharging processes through a web application using pre-defined profiles. This platform was developed aiming to test different batteries technologies. Considering the relevance of the energy storage area based in batteries, especially for the batteries applied to electric mobility systems, this platform allows to perform controlled tests to the batteries, in order to analyze the batteries performance under different scenarios of operation. Besides the results obtained with the batteries, this work also intends to produce results that can contribute to an involvement in the strengthening of the Internet-of-Things.
Resumo:
Poly(vinylidene fluoride) (PVDF) is a biocompatible material with excellent electroactive properties. Non-electroactive α-PVDF and electroactive β-PVDF were used to investigate the substrate polarization and polarity influence on the focal adhesion size and number as well as on human adipose stem cells (hASCs) differentiation. hASCs were cultured on different PVDF surfaces adsorbed with fibronectin and focal adhesion size and number, total adhesion area, cell size, cell aspect ratio and focal adhesion density were estimated using cells expressing EGFP-vinculin. Osteogenic differentiation was also determined using a quantitative alkaline phosphatase assay. The surface charge of the poled PVDF films (positive or negative) influenced the hydrophobicity of the samples, leading to variations in the conformation of adsorbed extracellular matrix (ECM) proteins, which ultimately modulated the stem cell adhesion on the films and induced their osteogenic differentiation.
Resumo:
In tissue engineering of cartilage, polymeric scaffolds are implanted in the damaged tissue and subjected to repeated compression loading cycles. The possibility of failure due to mechanical fatigue has not been properly addressed in these scaffolds. Nevertheless, the macroporous scaffold is susceptible to failure after repeated loading-unloading cycles. This is related to inherent discontinuities in the material due to the micropore structure of the macro-pore walls that act as stress concentration points. In this work, chondrogenic precursor cells have been seeded in Poly-ε-caprolactone (PCL) scaffolds with fibrin and some were submitted to free swelling culture and others to cyclic loading in a bioreactor. After cell culture, all the samples were analyzed for fatigue behavior under repeated loading-unloading cycles. Moreover, some components of the extracellular matrix (ECM) were identified. No differences were observed between samples undergoing free swelling or bioreactor loading conditions, neither respect to matrix components nor to mechanical performance to fatigue. The ECM did not achieve the desired preponderance of collagen type II over collagen type I which is considered the main characteristic of hyaline cartilage ECM. However, prediction in PCL with ECM constructs was possible up to 600 cycles, an enhanced performance when compared to previous works. PCL after cell culture presents an improved fatigue resistance, despite the fact that the measured elastic modulus at the first cycle was similar to PCL with poly(vinyl alcohol) samples. This finding suggests that fatigue analysis in tissue engineering constructs can provide additional information missed with traditional mechanical measurements.
Resumo:
Mushrooms are rich sources of bioactive compounds such as phenolic acids. When ingested, these molecules have to be released from the matrix to be transformed/absorbed by the organism, so that they can exert their bioactivity. Several in vitro methodologies have been developed in order to evaluate the bioavailability of bioactive compounds. Herein, two Hericium species were analyzed for their chemical composition and antioxidant activity. Furthermore, an in vitro digestion of the mushrooms and mushroom phenolic extracts was performed, and the digested samples were also submitted to antioxidant activity evaluation in order to evaluate the bioaccessibility of the phenolic acids identified in the samples. Hericium species showed similar chemical profiles (except for tocopherols), varying only in the concentration of the compounds. The phenolic extracts revealed higher antioxidant activity than the in vitro digested samples, meaning that this process decrease the antioxidant properties of the extract/mushroom. Nevertheless, phenolic acids were found in the digested samples, meaning that those molecules are bioaccessible.
Resumo:
The synthesis and biological evaluation of novel 1-aryl-3-[2-, 3- or 4-(thieno[3,2-b]pyridin-7-ylthio)phenyl]ureas 3, 4 and 5 as VEGFR-2 tyrosine kinase inhibitors, are reported. The 1-aryl-3-[3-(thieno[3,2-b]pyridin-7-ylthio)phenyl]ureas 4a-4h, with the arylurea in the meta position to the thioether, showed the lowest IC50 values in enzymatic assays (10-206 nM), the most potent compounds 4d-4h (IC50 10-28 nM) bearing hydrophobic groups (Me, F, CF3 and Cl) in the terminal phenyl ring. A convincing rationalization was achieved for the highest potent compounds 4 as type II VEGFR-2 inhibitors, based on the simultaneous presence of: (1) the thioether linker and (2) the arylurea moiety in the meta position. For compounds 4, significant inhibition of Human Umbilical Vein Endothelial Cells (HUVECs) proliferation (BrdU assay), migration (wound-healing assay) and tube formation were observed at low concentrations. These compounds have also shown to increase apoptosis using the TUNEL assay. Immunostaining for total and phosphorylated (active) VEGFR-2 was performed by Western blotting. The phosphorylation of the receptor was significantly inhibited at 1.0 and 2.5 microM for the most promising compounds. Altogether, these findings point to an antiangiogenic effect in HUVECs.
Resumo:
OBJECTIVE: To compare the lipid profiles and coronary heart disease risks of 2 Brazilian Amazonian populations as follows: a riverside population (village of Vigia) and an urban population (city of Belém in the state of Pará). METHODS: Fifty individuals controlled for age and sex were assessed in each region, and the major risk factors for coronary heart disease were analyzed. RESULTS: According to the National Cholesterol Education Program (NCEP III) and using the Framingham score, both populations had the same absolute risk of events (Vigia = 5.4 ± 1 vs Belém = 5.7 ± 1), although the population of Vigia had a lower consumption of saturated fat (P<0.0001), a greater consumption of mono- and polyunsaturated fat (P<0.03), in addition to lower values for body mass index (25.4± 0.6 vs 27.6 ± 0.7 kg/m², P<0.02), of biceps skin fold (18.6 ± 1.1 vs 27.5 ± 1.3 mm, P<0.0001), of triceps skin fold (28.7 ± 1.2 vs 37.3 ± 1.7 mm, P<0.002), and of total cholesterol (205 ± 5 vs 223 ± 6 mg/dL, P< 0.03) and triglycerides (119 ± 9 vs 177 ± 18 mg/dL, P<0.005). Both populations did not differ in regard to HDL-C (46 ± 1 vs 46 ± 1 mg/dL), LDL-C (135 ± 4 vs 144 ± 5 mg/dL) and blood pressure (SBP 124 ± 3 vs 128 ± 3 mmHg; DBP 80 ± 2 vs 82 ± 2 mmHg). CONCLUSION: The riverside and urban populations of Amazonia had similar cardiovascular risks. However, the marked difference in the variables studied suggests that different strategies of prevention should be applied.
Resumo:
FUNDAMENTO: A oxidação da lipoproteÃna de baixa densidade (LDL-ox) induz à formação de epÃtopos imunogênicos na molécula. A presença de autoanticorpos contra a LDL-ox tem sido demonstrada no soro de pacientes com doença arterial coronariana (DAC). Contudo, o papel desses autoanticorpos na fisiopatologia das sÃndromes coronarianas agudas (SCA) e o seu significado clÃnico permanecem indefinidos. OBJETIVO: Avaliar a associação entre autoanticorpos contra a LDL-ox e SCA. MÉTODOS: Os tÃtulos de imunoglobulina G autoanticorpos contra a LDL-ox por cobre (antiLDL-ox) e contra o peptÃdeo sintético D derivado da apolipoproteÃna B (antipeptD) foram determinados por ensaio imunoenzimático (ELISA) em 90 pacientes, nas primeiras 12h de SCA (casos) e em 90 pacientes com DAC crônica (controles). RESULTADOS: Os resultados mostraram que os tÃtulos de antiLDL-ox foram significativamente mais elevados (p = 0,017) nos casos (0,40 ± 0,22), do que nos controles (0,33 ± 0,23). Por outro lado, os tÃtulos de antipeptD foram significativamente menores (p < 0,01) nos casos (0,28 ± 0,23) do que nos controles (0,45 ± 0,30). A diferença dos tÃtulos de ambos anticorpos entre os dois grupos estudados foi independente de idade, sexo, hipertensão arterial, diabete melito, dislipidemia, Ãndice de massa corporal, tabagismo, perfil lipÃdico, uso de estatinas e história familiar de DAC. CONCLUSÃO: Os resultados mostraram que os tÃtulos de antiLDL-ox foram significativamente mais elevados nos pacientes com sÃndrome coronariana aguda quando comparados aos pacientes com doença arterial coronariana e podem estar associados à instabilidade da placa aterosclerótica.
Resumo:
A produção de matéria seca e a absorção de micronutrientes (B, Cu, Fe, Mn e Zn) pelo arroz var. IAC-47 foram estudadas usando-se plantas cultivadas em solução nutritiva. Verificou-se que: enquanto as curvas que descrevem o crescimento e a acumulação de B e Fe mostram tendência sigmóide, as demais não o fazem, evidência de redistribuição foi observada somente nos casos do B (diminuição no conteúdo foliar) e no do Fe (diminuição no conteúdo da raiz).