Estudo sobre uma turbina a gás instalada em uma refinaria de petróleo

The gas turbine (GT) is known to have: low cost of capital over the amount of energy, high flexibility, high reliability, short delivery time, commissioning and commercial operation at the beginning and quick departure. The gas turbine is also recognized for its superior environmental performance, manifested in air pollution containment and reducing greenhouse gases (Mahi, 1994). Gas turbines in simple cycle mode (SC) have long been used by utilities to limited power generation peak. In addition, manufacturing facilities use gas turbines for power generation units on site, often in combination with the process of heat production, such as hot water and steam process. In recent years, the performance of industrial gas turbines has been improved due to significant investments in research and development, in terms of fuel to electricity conversion efficiency, plant capacity, availability and reliability. The greater availability of energy resources such as natural gas (NG), the significant reduction of capital costs and the introduction of advanced cycles, have also been a success factor for the increased use of gas turbines to load applications base (Poulikas, 2004). Open Cycle Gas Turbine with a greater degree of heat to the atmosphere may alternatively be used to produce additional electricity using a steam cycle, or to compose a cogeneration process. The combined cycle (CC) uses the heat from the gas turbine exhaust gas to increase the power output and increase the overall efficiency of more than 50% second (Najjar, 2001). The initial discovery of these cycles in the commercial power generation market was possible due to the development of the gas turbine. Only from the 1970s that gas turbine inlet temperature and therefore the exhaust gas temperature was sufficiently high to allow a better efficiency in the combined cycle ... (Complete Abstract click electronic access below)

Análise energética da aplicação de torta de filtro na substituição parcial da adubação inorgânica sintética da cana-de-açúcar

Pós-graduação em Agronomia (Energia na Agricultura) - FCA

O papel dos consumidores residencias no ambiente das redes inteligentes: medidores eletrônicos de energia

Pós-graduação em Engenharia Mecânica - FEG

Análise das eficiências energética e econômica de dois diferentes sistemas de produção de leite bovino em explorações familiares

This study aimed to analyze the energy efficiency ratings and cost of farming families producing milk in the city of Pardinho (SP). The hypothesis that guides the study is that energy expenditure may be coincident with the economic expenditure showing that there is a relationship between these flows, which can be sustainable or not. To better define the producers studied criteria were used in the official system of rural credit FEAP. Through primary data obtained by the speeches, the itineraries were reconstituted technical detailing the operations employed. Thus, we found two producers with different technical routes. The producer was the one who got one of the highest efficiencies 8.66 and 1.48 respectively. Related to the efficiency, we can see that are close related and when there is a broader idea of the allocation of energy resources and, thus, a better view of the sustainability of the agro ecosystem.

Eficiência energética e econômica da produção de leite bovino em explorações familiares no município de Pardinho, região de Botucatu- SP

The study aimed to analyze the energy and economic efficiency rate family farms producing milk in the county of Pardinho, Sao Paulo State. The criteria used to define producers in this study is that outlined by the Brazilian agricultural credit system FEAP (Fund Expansion of Agribusiness Paulista). Through primary data, obtained by verbal reports, the agroecosystem technical itineraries were re-established, detailing the process applied, machinery, implements, equipment, supplies and manual work. These were transformed into energy and economic units, which allowed determining the established connection between energy economics outputs and inputs. The hypothesis of this study is that the energetic expenditure may be coincidental with economic expenditures. The energetic and economic flows were analyzed, using a structure of expenditures, by type, source and form of gross energy, as well as the energetic point of view. Four producers were found to have different technical itineraries. Producers 1 and 2 achieved the highest energy and economic efficiency rates. The producer with the lowest efficiency rates was producer 4. The energy sources not renewable like chemical fertilizers were the most used reaching an average of 82.9% for the energy and 52.86% for the economic expenditures. When comparing energy and economic efficiency it is possible to verify that both forms of analysis are close, obtaining a broader idea about energy resources allocation.

Desenvolvimento de um sistema de proteção e metodologia para localização de faltas em sistemas de distribuição

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Ciclo de cogeração a partir de resíduos de poda de árvores na cidade de Guaratinguetá

The current socio-economic situation has brought a need to look for alternative ways to get energy that allow reducing the high dependence on fossil fuel sources while deflect from the climate change arising from the result of the use of these energy resources. Renewable sources of energy, low and medium temperature appear as high potential of energy resources, which have a major influence on the way of life of the people to enable decentralized energy production. In Brazil, in particular, have also the need to decentralize the energy grid, currently focused on energy from water source. The current water crisis, exemplifies the urgency of betting on other energy sources, as a way to help in emergency situations such as the current one. Therefore, this study evaluates the possibility of using biomass as a heat source in a Rankine Cycle Organic where instead of water; it uses thermal fluid as working fluid, was compared the urban areas of the city of Guaratinguetá with the urban area of the metropolitan region of São Paulo. Thus, it was established two scenarios, so it was possible to establish the cycle to be used

Group Rekeying Schemes for Secure Group Communication in Wireless Sensor Networks

Wireless sensor networks are promising solutions for many applications. However, wireless sensor nodes suffer from many constraints such as low computation capability, small memory, limited energy resources, and so on. Grouping is an important technique to localize computation and reduce communication overhead in wireless sensor networks. In this paper, we use grouping to refer to the process of combining a set of sensor nodes with similar properties. We propose two centralized group rekeying (CGK) schemes for secure group communication in sensor networks. The lifetime of a group is divided into three phases, i.e., group formation, group maintenance, and group dissolution. We demonstrate how to set up the group and establish the group key in each phase. Our analysis shows that the proposed two schemes are computationally efficient and secure.

Ciclo de cogeração a partir de resíduos de poda de árvores na cidade de Guaratinguetá

The current socio-economic situation has brought a need to look for alternative ways to get energy that allow reducing the high dependence on fossil fuel sources while deflect from the climate change arising from the result of the use of these energy resources. Renewable sources of energy, low and medium temperature appear as high potential of energy resources, which have a major influence on the way of life of the people to enable decentralized energy production. In Brazil, in particular, have also the need to decentralize the energy grid, currently focused on energy from water source. The current water crisis, exemplifies the urgency of betting on other energy sources, as a way to help in emergency situations such as the current one. Therefore, this study evaluates the possibility of using biomass as a heat source in a Rankine Cycle Organic where instead of water; it uses thermal fluid as working fluid, was compared the urban areas of the city of Guaratinguetá with the urban area of the metropolitan region of São Paulo. Thus, it was established two scenarios, so it was possible to establish the cycle to be used

El gran reto de la integración de la electricidad de origen renovable en las redes eléctricas de Canarias

[ES] Las Islas Canarias carecen totalmente de recursos energéticos convencionales, representando la importación de energía primaria un 98% del consumo del Archipiélago. En la actualidad las Islas se suministran de petróleo y sus derivados, importándolos mediante buques. Sin embargo, Canarias posee un alto potencial de energías renovables, energías autóctonas y limpias, pero tan sólo un 2% del consumo de energía primaria procede de energías renovables. La búsqueda de la sostenibilidad energética es uno de los grandes desafíos de Canarias y la integración de la electricidad de origen renovable en sus redes eléctricas uno de los grandes retos que podría convertir a Canarias en un laboratorio a nivel mundial; el ejemplo de la isla de El Hierro así lo constata. Este artículo versa sobre este gran reto que supone la integración de energías renovables en las redes eléctricas de Canarias.

Cooperative communication and distributed detection in wireless sensor networks

Recent progress in microelectronic and wireless communications have enabled the development of low cost, low power, multifunctional sensors, which has allowed the birth of new type of networks named wireless sensor networks (WSNs). The main features of such networks are: the nodes can be positioned randomly over a given field with a high density; each node operates both like sensor (for collection of environmental data) as well as transceiver (for transmission of information to the data retrieval); the nodes have limited energy resources. The use of wireless communications and the small size of nodes, make this type of networks suitable for a large number of applications. For example, sensor nodes can be used to monitor a high risk region, as near a volcano; in a hospital they could be used to monitor physical conditions of patients. For each of these possible application scenarios, it is necessary to guarantee a trade-off between energy consumptions and communication reliability. The thesis investigates the use of WSNs in two possible scenarios and for each of them suggests a solution that permits to solve relating problems considering the trade-off introduced. The first scenario considers a network with a high number of nodes deployed in a given geographical area without detailed planning that have to transmit data toward a coordinator node, named sink, that we assume to be located onboard an unmanned aerial vehicle (UAV). This is a practical example of reachback communication, characterized by the high density of nodes that have to transmit data reliably and efficiently towards a far receiver. It is considered that each node transmits a common shared message directly to the receiver onboard the UAV whenever it receives a broadcast message (triggered for example by the vehicle). We assume that the communication channels between the local nodes and the receiver are subject to fading and noise. The receiver onboard the UAV must be able to fuse the weak and noisy signals in a coherent way to receive the data reliably. It is proposed a cooperative diversity concept as an effective solution to the reachback problem. In particular, it is considered a spread spectrum (SS) transmission scheme in conjunction with a fusion center that can exploit cooperative diversity, without requiring stringent synchronization between nodes. The idea consists of simultaneous transmission of the common message among the nodes and a Rake reception at the fusion center. The proposed solution is mainly motivated by two goals: the necessity to have simple nodes (to this aim we move the computational complexity to the receiver onboard the UAV), and the importance to guarantee high levels of energy efficiency of the network, thus increasing the network lifetime. The proposed scheme is analyzed in order to better understand the effectiveness of the approach presented. The performance metrics considered are both the theoretical limit on the maximum amount of data that can be collected by the receiver, as well as the error probability with a given modulation scheme. Since we deal with a WSN, both of these performance are evaluated taking into consideration the energy efficiency of the network. The second scenario considers the use of a chain network for the detection of fires by using nodes that have a double function of sensors and routers. The first one is relative to the monitoring of a temperature parameter that allows to take a local binary decision of target (fire) absent/present. The second one considers that each node receives a decision made by the previous node of the chain, compares this with that deriving by the observation of the phenomenon, and transmits the final result to the next node. The chain ends at the sink node that transmits the received decision to the user. In this network the goals are to limit throughput in each sensor-to-sensor link and minimize probability of error at the last stage of the chain. This is a typical scenario of distributed detection. To obtain good performance it is necessary to define some fusion rules for each node to summarize local observations and decisions of the previous nodes, to get a final decision that it is transmitted to the next node. WSNs have been studied also under a practical point of view, describing both the main characteristics of IEEE802:15:4 standard and two commercial WSN platforms. By using a commercial WSN platform it is realized an agricultural application that has been tested in a six months on-field experimentation.

Biomasse e loro quantificazione economica per un efficiente uso dell'energia

Biomasses and their possible use as energy resource are of great interest today, and the general problem of energy resources as well. In the present study the key questions of the convenience, from both energy and economy standpoints, have been addressed without any bias: the problem has been handled starting from “philosophical” bases disregarding any pre-settled ideology or political trend, but simply using mathematical approaches as logical tools for defining balances in a right way. In this context quantitative indexes such as LCA and EROEI have been widely used, together with multicriteria methods (such as ELECTRE) as decision supporting tools. This approach permits to remove mythologies, such as the unrealistic concept of clean energy, or the strange idea of biomasses as a magic to solve every thing in the field of the energy. As a consequence the present study aims to find any relevant aspect potentially useful for the society, looking at any possible source of energy without prejudices but without unrealistic expectations too. For what concerns biomasses, we studied in great details four very different cases of study, in order to have a scenario as various as much we can. A relevant result is the need to use biomasses together with other more efficient sources, especially recovering by-products from silviculture activities: but attention should be paid to the transportation and environmental costs. Another relevant result is the very difficult possibility of reliable evaluation of dedicated cultures as sources for “biomasses for energy”: the problem has to be carefully evaluated case-by-case, because what seems useful in a context, becomes totally disruptive in another one. In any case the concept itself of convenience is not well defined at a level of macrosystem: it seems more appropriate to limit this very concept at a level of microsystem, considering that what sounds fine in a limited well defined microsystem may cause great damage in another slightly different, or even very similar, microsystem. This approach seems the right way to solve the controversy about the concept of convenience.

Luminophores and Carbon nanostructures: towards new functional materials

In the scenario of depleting fossil fuels, finding new energy technologies and conserving conventional energy resources have become essential to sustain modern civilization. While renewable energies are on the rise, considerable interest has been turned also to reduce energy consumption of conventional devices and appliances, which are often not yet optimized for this purpose. Modern nanotechnology provides a platform to build such devices by using nanomaterials showing exceptional physico-chemical properties. In particular, carbon materials (fullerenes, carbon nanotubes, graphene etc.), which show high thermal and electrical conductivity, aspect ratio, shear strength and chemical/mechanical resistance, are quite promising for a wide range of applications. However, the problem of solubility often hampers their handling and industrial utilization. These limitations can be mitigated by functionalizing carbon nanostructures, either covalently or non covalently, with organic or inorganic compounds. The exo- and endohedral functionalization of carbon nanotubes (CNTs) with organic/inorganic moieties to produce luminescent materials with desired properties are the main focus of this doctoral work. These hybrids have been thoroughly designed and characterized with chemical, microscopic and photophysical analyses. All the materials based on carbon nanostructures described in this thesis are innovative examples of photoactive and luminescent hybrids, and their morphological and photophysical properties help understanding the nature of interactions between the active units. This may prompt the design and fabrication of new functional materials for applications in the fields of optoelectronics and photovoltaics.

Prestazioni energetico-ambientali di sistemi cogenerativi avanzati e analisi di casi applicativi

Lo scopo di questa tesi è quello di analizzare dapprima l’impatto ambientale di tali impianti e poi analizzare il contributo effettivo che oggi la tecnologia innovativa dei cicli Rankine organici può dare nella valorizzazione elettrica del calore di scarto di processi industriali, focalizzando l’obiettivo principalmente sulle turbine a gas ed eseguendo un caso di studio in un settore ancora poco esplorato da questa tecnologia, quello Oil&Gas. Dopo aver effettuato il censimento degli impianti a fonti fossili e rinnovabili, cogenerativi e non, presenti in Emilia-Romagna, è stato sviluppato un software chiamato MiniBref che permette di simulare il funzionamento di una qualsiasi centrale termoelettrica grazie alla possibilità di combinare la tecnologia dell’impianto con il tipo di combustibile consentendo la valutazione delle emissioni inquinanti ed i potenziali di inquinamento. Successivamente verranno illustrati gli ORC, partendo dalle caratteristiche impiantistiche e termodinamiche fino ad arrivare alla scelta del fluido organico, fondamentale per le performance del ciclo. Dopo aver effettuato una ricognizione dello stato dell’arte delle applicazioni industriali degli ORC nel recupero termico, verranno eseguite simulazioni numeriche per ricostruire gli ORC ed avere una panoramica il più completa ed attendibile delle prestazioni effettive di questi sistemi. In ultimo verranno illustrati i risultati di un caso di studio che vede l’adozione di recupero mediante ciclo organico in un’installazione esistente del settore Oil&Gas. Si effettuerà uno studio delle prestazione dell’impianto al variare delle pressioni massime e minime del ciclo ed al variare del fluido impiegato al fine di mostrare come questi parametri influenzino non solo le performance ma anche le caratteristiche impiantistiche da adottare. A conclusione del lavoro si riporteranno i risultati relativi all’analisi condotte considerando l’impianto ai carichi parziali ed in assetto cogenerativo.

Modelling and analysis of networked control strategies in smart power distribution grids: development of co-simulation tools

This thesis is focused on Smart Grid applications in medium voltage distribution networks. For the development of new applications it appears useful the availability of simulation tools able to model dynamic behavior of both the power system and the communication network. Such a co-simulation environment would allow the assessment of the feasibility of using a given network technology to support communication-based Smart Grid control schemes on an existing segment of the electrical grid and to determine the range of control schemes that different communications technologies can support. For this reason, is presented a co-simulation platform that has been built by linking the Electromagnetic Transients Program Simulator (EMTP v3.0) with a Telecommunication Network Simulator (OPNET-Riverbed v18.0). The simulator is used to design and analyze a coordinate use of Distributed Energy Resources (DERs) for the voltage/var control (VVC) in distribution network. This thesis is focused control structure based on the use of phase measurement units (PMUs). In order to limit the required reinforcements of the communication infrastructures currently adopted by Distribution Network Operators (DNOs), the study is focused on leader-less MAS schemes that do not assign special coordinating rules to specific agents. Leader-less MAS are expected to produce more uniform communication traffic than centralized approaches that include a moderator agent. Moreover, leader-less MAS are expected to be less affected by limitations and constraint of some communication links. The developed co-simulator has allowed the definition of specific countermeasures against the limitations of the communication network, with particular reference to the latency and loss and information, for both the case of wired and wireless communication networks. Moreover, the co-simulation platform has bee also coupled with a mobility simulator in order to study specific countermeasures against the negative effects on the medium voltage/current distribution network caused by the concurrent connection of electric vehicles.