Conceptual plan for an interactive highway safety design model. Final report.

Federal Highway Administration, Office of Safety and Traffic Operations Research and Development, McLean Va.

Design and cost analysis of truck-trailer rear underride guards. Final report.

National Highway Traffic Safety Administration, Washington, D.C.

Die design and construction; lanking, piercing, compound, progressive, trimming, flanging, forming, and cam dies.

Mode of access: Internet.

Project Neos; a general study of processes for the realization of design configurations in materials

"Cornell Aeronautical Laboratory. Contract: AF 33(600)-42921. ASD project NR 7-867."

Design methods for high frequency transformers.

"...Final report ... sponsored by Signal Corps Engineering Laboratories, Fort Monmouth, N.J., and the Electronic Components Laboratory of the Wright Air Development Center, Wright-Patterson Air Force Base, Ohio."

Making Space: Feasibility of Urban Manufacturing through Shared Resources

Thesis (Master's)--University of Washington, 2016-06

A preform design method for sheet superplastic bulging with finite element modeling

Superplastic bulging is the most successful application of superplastic forming (SPF) in industry, but the non-uniform wall thickness distribution of parts formed by it is a common technical problem yet to be overcome. Based on a rigid-viscoplastic finite element program developed by the authors, for simulation of the sheet superplastic forming process combined with the prediction of microstructure variations (such as grain growth and cavity growth), a simple and efficient preform design method is proposed and applied to the design of preform mould for manufacturing parts with uniform wall thickness. Examples of formed parts are presented here to demonstrate that the technology can be used to improve the uniformity of wall thickness to meet practical requirements. (C) 2004 Elsevier B.V. All rights reserved.

Life Cycle Assessment (LCA) Applied to the Design of an Innovative Drying Process for Sewage Sludge

Most adverse environmental impacts result from design decisions made long before manufacturing or usage. In order to prevent this situation, several authors have proposed the application of life cycle assessment (LCA) at the very first phases of the design of a process, a product or a service. The study in this paper presents an innovative thermal drying process for sewage sludge called fry-drying, in which dewatered sludge is directly contacted in the dryer with hot recycled cooking oils (RCO) as the heat medium. Considering the practical difficulties for the disposal of these two wastes, fry-drying presents a potentially convenient method for their combined elimination by incineration of the final fry-dried sludge. An analytical comparison between a conventional drying process and the new proposed fry-drying process is reported, with reference to some environmental impact categories. The results of this study, applied at the earliest stages of the design of the process, assist evaluation of the feasibility of such system compared to a current disposal process for the drying and incineration of sewage sludge.

A magnetization mapping approach for passive shim design in MRI

A new passive shim design method is presented which is based on a magnetization mapping approach. Well defined regions with similar magnetization values define the optimal number of passive shims, their shape and position. The new design method is applied in a shimming process without prior-axial shim localization; this reduces the possibility of introducing new errors. The new shim design methodology reduces the number of iterations and the quantity of material required to shim a magnet. Only a few iterations (1-5) are required to shim a whole body horizontal bore magnet with a manufacturing error tolerance larger than 0.1 mm and smaller than 0.5 mm. One numerical example is presented

Managing innovative manufacturing

Editorial: The Managing Innovative Manufacturing (MIM) conference series started in 1993 in the UK. The first MIM conference was held at Keele University and, as from the second MIM at Leicester University in 1996, it became a biennial event with the University of Nottingham and Aston University hosting, respectively, the third and fourth conferences. The main areas of interest of the MIM conference series are: Manufacturing Strategy; Technology & Innovation Management; Human Resource Management; Organisation of Work; Product Design; Operations Planning and Control; Supply Chain Management; Performance Management. This special issue of the International Journal of Technology Management is based on selected papers from MIM2000 at Aston University, where it was organised by Aston Business School. The special theme of the Aston conference was Responsive Production and the Agile Enterprise. Altogether 82 papers were presented in parallel sessions. The eight papers included here were selected from the ‘Technology and Innovation’ stream. They have all been independently reviewed and revised before being accepted for publication. The authors of these papers are from the UK, Ireland, Turkey, the USA, the Netherlands and Hong Kong. They address a wide range of issues within the overall scope of Technology and Innovation with some papers having a geographical or sector focus and others being more general in nature. Participation in the MIM conferences has become increasingly international and to reflect this, the 2002 event is leaving the UK and being held at the University of Wisconsin-Milwaukee, in the USA. It is planned to hold the following MIM at the University of Aalborg, Denmark, in 2004.

Using simulation for facility design: a case study

A discrete event simulation model was developed and used to estimate the storage area required for a proposed overseas textile manufacturing facility. It was found that the simulation was able to achieve this because of its ability to both store attribute values and to show queuing levels at an individual product level. It was also found that the process of undertaking the simulation project initiated useful discussions regarding the operation of the facility. Discrete event simulation is shown to be much more than an exercise in quantitative analysis of results and an important task of the simulation project manager is to initiate a debate among decision makers regarding the assumptions of how the system operates.

Using system dynamics in a discrete-event simulation study of a manufacturing plant

Purpose - To provide an example of the use of system dynamics within the context of a discrete-event simulation study. Design/methodology/approach - A discrete-event simulation study of a production-planning facility in a gas cylinder-manufacturing plant is presented. The case study evidence incorporates questionnaire responses from sales managers involved in the order-scheduling process. Findings - As the project progressed it became clear that, although the discrete-event simulation would meet the objectives of the study in a technical sense, the organizational problem of "delivery performance" would not be solved by the discrete-event simulation study alone. The case shows how the qualitative outcomes of the discrete-event simulation study led to an analysis using the system dynamics technique. The system dynamics technique was able to model the decision-makers in the sales and production process and provide a deeper understanding of the performance of the system. Research limitations/implications - The case study describes a traditional discrete-event simulation study which incorporated an unplanned investigation using system dynamics. Further, case studies using a planned approach to showing consideration of organizational issues in discrete-event simulation studies are required. Then the role of both qualitative data in a discrete-event simulation study and the use of supplementary tools which incorporate organizational aspects may help generate a methodology for discrete-event simulation that incorporates human aspects and so improve its relevance for decision making. Practical implications - It is argued that system dynamics can provide a useful addition to the toolkit of the discrete-event simulation practitioner in helping them incorporate a human aspect in their analysis. Originality/value - Helps decision makers gain a broader perspective on the tools available to them by showing the use of system dynamics to supplement the use of discrete-event simulation. © Emerald Group Publishing Limited.

Design and development of agent-based procurement system to enhance business intelligence

The purpose of this research is to propose a procurement system across other disciplines and retrieved information with relevant parties so as to have a better co-ordination between supply and demand sides. This paper demonstrates how to analyze the data with an agent-based procurement system (APS) to re-engineer and improve the existing procurement process. The intelligence agents take the responsibility of searching the potential suppliers, negotiation with the short-listed suppliers and evaluating the performance of suppliers based on the selection criteria with mathematical model. Manufacturing firms and trading companies spend more than half of their sales dollar in the purchase of raw material and components. Efficient data collection with high accuracy is one of the key success factors to generate quality procurement which is to purchasing right material at right quality from right suppliers. In general, the enterprises spend a significant amount of resources on data collection and storage, but too little on facilitating data analysis and sharing. To validate the feasibility of the approach, a case study on a manufacturing small and medium-sized enterprise (SME) has been conducted. APS supports the data and information analyzing technique to facilitate the decision making such that the agent can enhance the negotiation and suppler evaluation efficiency by saving time and cost.