956 resultados para process parameter monitoring


Relevância:

90.00% 90.00%

Publicador:

Resumo:

During the past two decades, many researchers have developed methods for the detection of structural defects at the early stages to operate the aerospace vehicles safely and to reduce the operating costs. The Surface Response to Excitation (SuRE) method is one of these approaches developed at FIU to reduce the cost and size of the equipment. The SuRE method excites the surface at a series of frequencies and monitors the propagation characteristics of the generated waves. The amplitude of the waves reaching to any point on the surface varies with frequency; however, it remains consistent as long as the integrity and strain distribution on the part is consistent. These spectral characteristics change when cracks develop or the strain distribution changes. The SHM methods may be used for many applications, from the detection of loose screws to the monitoring of manufacturing operations. A scanning laser vibrometer was used in this study to investigate the characteristics of the spectral changes at different points on the parts. The study started with detecting a load on a plate and estimating its location. The modifications on the part with manufacturing operations were detected and the Part-Based Manufacturing Process Performance Monitoring (PbPPM) method was developed. Hardware was prepared to demonstrate the feasibility of the proposed methods in real time. Using low-cost piezoelectric elements and the non-contact scanning laser vibrometer successfully, the data was collected for the SuRE and PbPPM methods. Locational force, loose bolts and material loss could be easily detected by comparing the spectral characteristics of the arriving waves. On-line methods used fast computational methods for estimating the spectrum and detecting the changing operational conditions from sum of the squares of the variations. Neural networks classified the spectrums when the desktop – DSP combination was used. The results demonstrated the feasibility of the SuRE and PbPPM methods.

Relevância:

90.00% 90.00%

Publicador:

Resumo:

During the past two decades, many researchers have developed methods for the detection of structural defects at the early stages to operate the aerospace vehicles safely and to reduce the operating costs. The Surface Response to Excitation (SuRE) method is one of these approaches developed at FIU to reduce the cost and size of the equipment. The SuRE method excites the surface at a series of frequencies and monitors the propagation characteristics of the generated waves. The amplitude of the waves reaching to any point on the surface varies with frequency; however, it remains consistent as long as the integrity and strain distribution on the part is consistent. These spectral characteristics change when cracks develop or the strain distribution changes. The SHM methods may be used for many applications, from the detection of loose screws to the monitoring of manufacturing operations. A scanning laser vibrometer was used in this study to investigate the characteristics of the spectral changes at different points on the parts. The study started with detecting a load on a plate and estimating its location. The modifications on the part with manufacturing operations were detected and the Part-Based Manufacturing Process Performance Monitoring (PbPPM) method was developed. Hardware was prepared to demonstrate the feasibility of the proposed methods in real time. Using low-cost piezoelectric elements and the non-contact scanning laser vibrometer successfully, the data was collected for the SuRE and PbPPM methods. Locational force, loose bolts and material loss could be easily detected by comparing the spectral characteristics of the arriving waves. On-line methods used fast computational methods for estimating the spectrum and detecting the changing operational conditions from sum of the squares of the variations. Neural networks classified the spectrums when the desktop – DSP combination was used. The results demonstrated the feasibility of the SuRE and PbPPM methods.

Relevância:

90.00% 90.00%

Publicador:

Resumo:

This paper addresses the two opposing extremes of standardisation in franchising and the dynamics of sales in search of a juncture point in order to reduce franchisees’ uncertainties in sales and improve sales performance. A conceptual framework is developed based on both theory and practice in order to investigate the sales process of a specific franchise network. The research is conducted over a period of six weeks in form of a customised sales report considering the sales funnel concept and performance indicators along the sales process. The received quantitative data is analysed through descriptive statistics and logistic regressions in respect to what variations in the sales process can be discovered and what practices yield higher performance. The results indicate an advantage of a prioritisation guideline regarding the activities and choices to make as a salesperson over strict standardisation. Defining the sales funnel plus engaging in the process of monitoring sales in itself has proven to be a way of reducing uncertainty as the franchisor and franchisees alike inherently gain a greater understanding of the process. The extended knowledge gained from this research allowed for both practical as well as theoretical implications and expands the knowledge on standardisation of sales and the appropriateness of the sales funnel and its management for dealing with the dilemma between standardisation and flexibility of sales in franchising contexts.

Relevância:

80.00% 80.00%

Publicador:

Resumo:

Universidade Estadual de Campinas . Faculdade de Educação Física

Relevância:

80.00% 80.00%

Publicador:

Resumo:

The dynamics of mechanical milling in a vibratory mill have been studied by means of mechanical vibration, shock measurements, computer simulation and microstructural evolution measurements. Two distinct modes of ball motion during milling, periodic and chaotic vibration, were observed. Mill operation in the regime of periodic vibration, in which each collision provides a constant energy input to milled powders, enabled a quantitative description of the effect of process parameters on system dynamics. An investigation of the effect of process parameters on microstructural development in an austenitic stainless steel showed that the impact force associated with collision events is an important process parameter for characterizing microstructural evolution. (C) 1997 Elsevier Science S.A.

Relevância:

80.00% 80.00%

Publicador:

Resumo:

Dissertação apresentada para obtenção do grau de Mestre em Contabilidade e Finanças Orientador: Professor Doutor José Freitas Santos

Relevância:

80.00% 80.00%

Publicador:

Resumo:

A thesis submitted in fulfilment of the requirements for the Degree of Doctor of Philosophy in Sanitary Engineering in the Faculty of Sciences and Technology of the New University of Lisbon

Relevância:

80.00% 80.00%

Publicador:

Resumo:

O BIM – Building Information Modeling – é um conceito de controlo e gestão de informação desenvolvida, entre diferentes especialidades e intervenientes envolventes, durante o ciclo de vida das construções. A utilização das tecnologias BIM, no ramo da Engenharia Mecânica e Civil, tem sido uma aposta constante, e cada vez mais concisa, nos projetos de construção. A justificação para a adoção destas metodologias mais eficientes, em substituição dos processos convencionais, prende-se com o facto desses processos convencionais, ainda hoje, apresentarem muitas dificuldades e problemas associados, por exemplo, à falta de comunicação entre os intervenientes e ao ineficiente controlo na gestão de projetos. O objetivo desta dissertação centra-se na análise da interoperabilidade de softwares BIM, ou seja, na verificação da viabilidade de exportação de dados dos modelos produzidos, entre as ferramentas BIM. Para este campo de ação contribuirá a análise da passagem de informação, relativa ao modelo de uma Nave Industrial modelada, em alguns dos softwares BIM, correntemente mais utilizados. O conhecimento adquirido com a modelação do caso de estudo do presente trabalho irá permitir identificar algumas lacunas existentes ao nível da falta de recomendações práticas que sirvam de orientação na modelação recorrendo a ferramentas informáticas BIM-compatíveis. Assim, a base deste trabalho consiste na criação de uma série de recomendações ou de um roteiro de modelação em específico para a disciplina de estruturas enquanto área de aplicação concreta do estudo efetuado. Nesse sentido, a proposta deste trabalho é de apresentar alguns critérios de modelação onde são definidos os elementos a modelar em cada fase do projeto.

Relevância:

80.00% 80.00%

Publicador:

Resumo:

Dissertação de mestrado integrado em Engenharia Eletrónica Industrial e Computadores

Relevância:

80.00% 80.00%

Publicador:

Resumo:

Dissertação de mestrado em Educação Especial (área de especialização em Intervenção Precoce)

Relevância:

80.00% 80.00%

Publicador:

Resumo:

Energy management is the process of monitoring, controlling and conserving energy in a building or organisation. The main reasons for this are for cost purposes and benefit to the environment. Through various techniques and solutions for lighting, heating, office equipment, the building fabric etc along with a change in people’s attitudes there can be a substantial saving in the amount spent on energy. A good example o f energy waste in GMIT is the lighting situation in the library. All the lights are switched on all day on even in places where that is adequate daylighting, which is a big waste o f energy. Also the lights for book shelves are left on. Surely all these books won’t be searched for all at the one time. It would make much more sense to have local switches that the users can control when they are searching for a particular book. Heating controls for the older parts o f the college are badly needed. A room like 834 needs a TRV to prevent it from overheating as temperatures often reach the high twenties due to the heat from the radiators, computers, solar gains and heat from users o f the room. Also in the old part o f the college it is missing vital insulation, along with not being air tight due to the era when it was built. Pumped bonded bead insulation and sealant around services and gaps can greatly improve the thermal performance o f the building and help achieve a higher BER cert. GMIT should also look at the possibility o f installing a CHP plant to meet the base heating loads. It would meet the requirement o f running 4500 hours a year and would receive some financial support from the Accelerated Capital Allowance. I f people’s attitudes are changed through energy awareness campaigns and a few changes made for more energy efficient equipment, substantial savings can be made in the energy expenditure.

Relevância:

80.00% 80.00%

Publicador:

Resumo:

A laser-based technique for printing transparent and weakly absorbing liquids is developed. Its principle of operation relies in the tight focusing of short laser pulses inside the liquid and close to its free surface, in such a way that the laser radiation is absorbed in a tiny volume around the beam waist, with practically no absorption in any other location along the beam path. If the absorbed energy overcomes the optical breakdown threshold, a cavitation bubble is generated, and its expansion results in the propulsion of a small fraction of liquid which can be collected on a substrate, leading to the printing of a microdroplet for each laser pulse. The technique does not require the preparation of the liquid in thin film form, and its forward mode of operation imposes no restriction concerning the optical properties of the substrate. These characteristics make it well suited for printing a wide variety of materials of interest in diverse applications. We demonstrate that the film-free laser forward printing technique is capable of printing microdroplets with good resolution, reproducibility and control, and analyze the influence of the main process parameter, laser pulse energy. The mechanisms of liquid printing are also investigated: time-resolved imaging provides a clear picture of the dynamics of liquid transfer which allows understanding the main features observed in the printed droplets.

Relevância:

80.00% 80.00%

Publicador:

Resumo:

The building industry has a particular interest in using clinching as a joining method for frame constructions of light-frame housing. Normally many clinch joints are required in joining of frames.In order to maximise the strength of the complete assembly, each clinch joint must be as sound as possible. Experimental testing is the main means of optimising a particular clinch joint. This includes shear strength testing and visual observation of joint cross-sections. The manufacturers of clinching equipment normally perform such experimental trials. Finite element analysis can also be used to optimise the tool geometry and the process parameter, X, which represents the thickness of the base of the joint. However, such procedures require dedicated software, a skilled operator, and test specimens in order to verify the finite element model. In addition, when using current technology several hours' computing time may be necessary. The objective of the study was to develop a simple calculation procedure for rapidly establishing an optimum value for the parameter X for a given tool combination. It should be possible to use the procedure on a daily basis, without stringent demands on the skill of the operator or the equipment. It is also desirable that the procedure would significantly decrease thenumber of shear strength tests required for verification. The experimental workinvolved tests in order to obtain an understanding of the behaviour of the sheets during clinching. The most notable observation concerned the stage of the process in which the upper sheet was initially bent, after which the deformation mechanism changed to shearing and elongation. The amount of deformation was measured relative to the original location of the upper sheet, and characterised as the C-measure. By understanding in detail the behaviour of the upper sheet, it waspossible to estimate a bending line function for the surface of the upper sheet. A procedure was developed, which makes it possible to estimate the process parameter X for each tool combination with a fixed die. The procedure is based on equating the volume of material on the punch side with the volume of the die. Detailed information concerning the behaviour of material on the punch side is required, assuming that the volume of die does not change during the process. The procedure was applied to shear strength testing of a sample material. The sample material was continuously hot-dip zinc-coated high-strength constructional steel,with a nominal thickness of 1.0 mm. The minimum Rp0.2 proof stress was 637 N/mm2. Such material has not yet been used extensively in light-frame housing, and little has been published on clinching of the material. The performance of the material is therefore of particular interest. Companies that use clinching on a daily basis stand to gain the greatest benefit from the procedure. By understanding the behaviour of sheets in different cases, it is possible to use data at an early stage for adjusting and optimising the process. In particular, the functionality of common tools can be increased since it is possible to characterise the complete range of existing tools. The study increases and broadens the amount ofbasic information concerning the clinching process. New approaches and points of view are presented and used for generating new knowledge.

Relevância:

80.00% 80.00%

Publicador:

Resumo:

Työn tavoitteena oli Imatra Steel Oy Ab:n jatkojalostusosaston lämpökäsittelylaitosten energiatalouden parantaminen. Työssä etsittiin lämpökäsittelylaitoksen energiatalouteen haitallisesti vaikuttavia tekijöitä ja pyrittiin löytämään ratkaisuja energiatalouden parantamiseksi.Työtä varten on kerätty tietoa kirjallisista lähteistä, Imatra Steel Oy Ab:n henkilökunnalta, insinööritoimistoilta, lämpökäsittelyuunien valmistajilta ja muilta asiantuntijoilta, jotka ovat olleet tekemisissä lämpökäsittelylaitosten, lämpökäsittelyuunien tai niihin läheisesti liittyvien energiataloudellisien tekijöiden parissa.Imatra Steel Oy Ab:n lämpökäsittelylaitosten suurimmat energiankuluttajat ovat lämpökäsittelyuunit, jotka ovat rakennettu pääosin vuosina 1965 ja 1971, jolloin energiankulutukseen ja sen aiheuttamiin kustannuksiin ei tarvinnut kiinnittää samalla tavoin huomiota kuin nykyisin. Työssä keskitytäänkin pääasiassa uunien energiatalouteen.Lämpökäsittelylaitosten energiatalouden parantamisessa on ensin keskityttävä primäärienergiana käytettävän maakaasun kulutuksen vähentämiseen, jonka jälkeen voidaan keskittyä uuneista syntyvän hukkalämmön hyödyntämiseen. Jotta lämpökäsittelyuunit saataisiin toimimaan energiataloudellisesti tehokkaasti ja nykyisessä markkinatilanteessa kilpailukykyisesti, pitäisi uuneille laatia oma kehitysohjelma. Uunien energiatalouden seuranta ja kehittäminen edellyttää nykyisten jatkuvatoimisesti mitattavien prosessitietojen ja erillisillä mittauksilla kerättävän tiedon nykyistä tehokkaampaa hyödyntämistä sekä uusien ennen mittaamattomien prosessiparametrien hyödyntämistä. Tulevaisuudessa toteutettava prosessitietojen keräysjärjestelmä antaakin aivan uusia mahdollisuuksia uunien kehittämiseen ja seurantaan.

Relevância:

80.00% 80.00%

Publicador:

Resumo:

Diplomityön tarkoituksena oli selvittää kuitujen kihartuvuuden profiili koivu- ja havusellulinjalla prosessivaiheiden suhteen. Profiilin perusteella pyrittiin selvittämään kuitulinjojen prosessista kuitujen kiharuuteen voimakkaimmin vaikuttavia tekijöitä. Työn kirjallisuusosassa käsiteltiin kuitujen ominaisuuksia sekä teollisen sellun valmistusprosessin kuituihin aiheuttamia kuituvaurioita ja niiden mahdollisia syitä. Lisäksi käytiin läpi kuituvaurioiden analysointimenetelmiä ja kuituvaurioiden kanssa korreloivia sellun laatuarvoja. Työn kokeellinen osa suoritettiin kuitulinjojen normaalin tuotannon ohessa. Kokeellisen osan massanäytteitä otettiin varsin moninaisista tuotantotilanteista mahdollisimman kattavan kiharuusprofiilin aikaansaamiseksi. Koivusellulinjalla vuokeittimen tuotantotaso vaikutti suuresti valmistettavan sellun ominaisuuksiin. Kuituvaurioiden syntyyn voimakkaimmin vaikuttavaksi tekijäksi osoittautui keittimen pohja-alueen, puskun ja massan pesuvaiheen sakeus. Tämän alueen sakeus muuttui tuotantotason mukaan, tuotantotason kasvun myötä alueen sakeus laski. Sakeuden lasku vähensi kuitujen kiharuutta sekä massan venymää ja paransi vetojäykkyyttä. Tuotantotason kasvu paransi myös keittimestä otettujen massanäytteiden vetojäykkyyspotentiaalia. Havusellulinjalla käytetyn Lo-Solids –keittomallin ja konventionaalisen keittomallin kesken esiintyi varsin merkittäviä laadullisia eroja. Lo-Solids –keittomallilla keitetyt sellukuidut kihartuivat konventionaalisella keittomallilla keitettyjä sellukuituja enemmän. Lo-Solids –keittomallilla keitetyn sellun vetojäykkyys oli konventionaalisella mallilla keitetyn sellun vetojäykkyyttä heikompi.