Modulation of inflammatory mediators by Opuntia ficus-indica and Prunus avium bioproducts using an in vitro cell-based model of intestinal inflammation

Dissertation to obtain a Master Degree in Biotechnology

A FEM-based model to study the behaviour of corroded RC beams shear repaired by NSM CFRP rods technique

This paper presents the main features of finite element FE numerical model developed using the computer code FEMIX to predict the near-surface mounted NSM carbon-fiber-reinforced polymer CFRP rods shear repair contribution to corroded reinforced concrete RC beams. In the RC beams shear repaired with NSM technique, the Carbon Fibre Reinforced Polymer (CFRP) rods are placed inside pre-cut grooves onto the concrete cover of the RC beam’s lateral faces and are bonded to the concrete with high epoxy adhesive. Experimental and 3D numerical modelling results are presented in this paper in terms of load-deflection curves, and failure modes for 4 short corroded beams: two corroded beams (A1CL3-B and A1CL3-SB) and two control beams (A1T-B and A1T-SB), the beams noted with B were let repaired in bending only with NSM CFRP rods while the ones noted with SB were repaired in both bending and shear with NSM technique. The corrosion of the tensile steel bars and its effect on the shear capacity of the RC beams was discussed. Results showed that the FE model was able to capture the main aspects of the experimental load-deflection curves of the RC beams, moreover it has presented the experimental failure modes and FE numerical modelling crack patterns and both gave similar results for non-shear repaired beams which failed in diagonal tension mode of failure and for shear-repaired beams which failed due to large flexural crack at the middle of the beams along with the concrete crushing, three dimensional crack patterns were produced for shear-repaired beams in order to investigate the splitting cracks occurred at the middle of the beams and near the support.

An agent-based model to assess the attractiveness of industrial estates

This article describes the main approaches adopted in a study focused on planning industrial estates on a sub-regional scale. The study was supported by an agent-based model, using firms as agents to assess the attractiveness of industrial estates. The simulation was made by the NetLogo toolkit and the environment represents a geographical space. Three scenarios and four hypotheses were used in the simulation to test the impact of different policies on the attractiveness of industrial estates. Policies were distinguished by the level of municipal coordination at which they were implemented and by the type of intervention. In the model, the attractiveness of industrial estates was based on the level of facilities, amenities, accessibility and on the price of land in each industrial estate. Firms are able to move and relocate whenever they find an attractive estate. The relocating firms were selected by their size, location and distance to an industrial estate. Results show that a coordinated policy among municipalities is the most efficient policy to promote advanced-qualified estates. In these scenarios, it was observed that more industrial estates became attractive, more firms were relocated and more vacant lots were occupied. Furthermore, the results also indicate that the promotion of widespread industrial estates with poor-quality infrastructures and amenities is an inefficient policy to attract firms.

A FEM-based model to study the behaviour of corroded RC beams shear repaired by NSM CFRP rods technique

This paper presents the main features of finite element FE numerical model developed using the computer code FEMIX to predict the near-surface mounted NSM carbon-fiber-reinforced polymer CFRP rods shear repair contribution to corroded reinforced concrete RC beams. In the RC beams shear repaired with NSM technique, the Carbon Fibre Reinforced Polymer (CFRP) rods are placed inside pre-cut grooves onto the concrete cover of the RC beam’s lateral faces and are bonded to the concrete with high epoxy adhesive. Experimental and 3D numerical modelling results are presented in this paper in terms of load-deflection curves, failure modes and slip information of the tensile steel bars for 4 short corroded beams: two corroded beams (A1CL3-B and A1CL3-SB) and two control beams (A1T-B and A1T-SB), the beams noted with B were let repaired in bending only with NSM CFRP rods while the ones noted with SB were repaired in both bending and shear with NSM technique. The corrosion of the tensile steel bars and its effect on the shear capacity of the RC beams was discussed. Results showed that the FE model was able to capture the main aspects of the experimental load-deflection curves of the RC beams, moreover it has presented the experimental failure modes and FE numerical modelling crack patterns and both gave similar results for non-shear repaired beams which failed in diagonal tension mode of failure and for shear-repaired beams which failed due to large flexural crack at the middle of the beams along with the concrete crushing, three dimensional crack patterns were produced for shear-repaired beams in order to investigate the splitting cracks occurred at the middle of the beams and near the support.

A cell-based model of extracellular-matrix-guided endothelial cell migration during angiogenesis.

Angiogenesis, the formation of new blood vessels sprouting from existing ones, occurs in several situations like wound healing, tissue remodeling, and near growing tumors. Under hypoxic conditions, tumor cells secrete growth factors, including VEGF. VEGF activates endothelial cells (ECs) in nearby vessels, leading to the migration of ECs out of the vessel and the formation of growing sprouts. A key process in angiogenesis is cellular self-organization, and previous modeling studies have identified mechanisms for producing networks and sprouts. Most theoretical studies of cellular self-organization during angiogenesis have ignored the interactions of ECs with the extra-cellular matrix (ECM), the jelly or hard materials that cells live in. Apart from providing structural support to cells, the ECM may play a key role in the coordination of cellular motility during angiogenesis. For example, by modifying the ECM, ECs can affect the motility of other ECs, long after they have left. Here, we present an explorative study of the cellular self-organization resulting from such ECM-coordinated cell migration. We show that a set of biologically-motivated, cell behavioral rules, including chemotaxis, haptotaxis, haptokinesis, and ECM-guided proliferation suffice for forming sprouts and branching vascular trees.

KCM, a general framework for codon-based model of evolution

With the advancement of high-throughput sequencing and dramatic increase of available genetic data, statistical modeling has become an essential part in the field of molecular evolution. Statistical modeling results in many interesting discoveries in the field, from detection of highly conserved or diverse regions in a genome to phylogenetic inference of species evolutionary history Among different types of genome sequences, protein coding regions are particularly interesting due to their impact on proteins. The building blocks of proteins, i.e. amino acids, are coded by triples of nucleotides, known as codons. Accordingly, studying the evolution of codons leads to fundamental understanding of how proteins function and evolve. The current codon models can be classified into three principal groups: mechanistic codon models, empirical codon models and hybrid ones. The mechanistic models grasp particular attention due to clarity of their underlying biological assumptions and parameters. However, they suffer from simplified assumptions that are required to overcome the burden of computational complexity. The main assumptions applied to the current mechanistic codon models are (a) double and triple substitutions of nucleotides within codons are negligible, (b) there is no mutation variation among nucleotides of a single codon and (c) assuming HKY nucleotide model is sufficient to capture essence of transition- transversion rates at nucleotide level. In this thesis, I develop a framework of mechanistic codon models, named KCM-based model family framework, based on holding or relaxing the mentioned assumptions. Accordingly, eight different models are proposed from eight combinations of holding or relaxing the assumptions from the simplest one that holds all the assumptions to the most general one that relaxes all of them. The models derived from the proposed framework allow me to investigate the biological plausibility of the three simplified assumptions on real data sets as well as finding the best model that is aligned with the underlying characteristics of the data sets. -- Avec l'avancement de séquençage à haut débit et l'augmentation dramatique des données géné¬tiques disponibles, la modélisation statistique est devenue un élément essentiel dans le domaine dé l'évolution moléculaire. Les résultats de la modélisation statistique dans de nombreuses découvertes intéressantes dans le domaine de la détection, de régions hautement conservées ou diverses dans un génome de l'inférence phylogénétique des espèces histoire évolutive. Parmi les différents types de séquences du génome, les régions codantes de protéines sont particulièrement intéressants en raison de leur impact sur les protéines. Les blocs de construction des protéines, à savoir les acides aminés, sont codés par des triplets de nucléotides, appelés codons. Par conséquent, l'étude de l'évolution des codons mène à la compréhension fondamentale de la façon dont les protéines fonctionnent et évoluent. Les modèles de codons actuels peuvent être classés en trois groupes principaux : les modèles de codons mécanistes, les modèles de codons empiriques et les hybrides. Les modèles mécanistes saisir une attention particulière en raison de la clarté de leurs hypothèses et les paramètres biologiques sous-jacents. Cependant, ils souffrent d'hypothèses simplificatrices qui permettent de surmonter le fardeau de la complexité des calculs. Les principales hypothèses retenues pour les modèles actuels de codons mécanistes sont : a) substitutions doubles et triples de nucleotides dans les codons sont négligeables, b) il n'y a pas de variation de la mutation chez les nucléotides d'un codon unique, et c) en supposant modèle nucléotidique HKY est suffisant pour capturer l'essence de taux de transition transversion au niveau nucléotidique. Dans cette thèse, je poursuis deux objectifs principaux. Le premier objectif est de développer un cadre de modèles de codons mécanistes, nommé cadre KCM-based model family, sur la base de la détention ou de l'assouplissement des hypothèses mentionnées. En conséquence, huit modèles différents sont proposés à partir de huit combinaisons de la détention ou l'assouplissement des hypothèses de la plus simple qui détient toutes les hypothèses à la plus générale qui détend tous. Les modèles dérivés du cadre proposé nous permettent d'enquêter sur la plausibilité biologique des trois hypothèses simplificatrices sur des données réelles ainsi que de trouver le meilleur modèle qui est aligné avec les caractéristiques sous-jacentes des jeux de données. Nos expériences montrent que, dans aucun des jeux de données réelles, tenant les trois hypothèses mentionnées est réaliste. Cela signifie en utilisant des modèles simples qui détiennent ces hypothèses peuvent être trompeuses et les résultats de l'estimation inexacte des paramètres. Le deuxième objectif est de développer un modèle mécaniste de codon généralisée qui détend les trois hypothèses simplificatrices, tandis que d'informatique efficace, en utilisant une opération de matrice appelée produit de Kronecker. Nos expériences montrent que sur un jeux de données choisis au hasard, le modèle proposé de codon mécaniste généralisée surpasse autre modèle de codon par rapport à AICc métrique dans environ la moitié des ensembles de données. En outre, je montre à travers plusieurs expériences que le modèle général proposé est biologiquement plausible.

MORM--a Petri net based model for assessing OH&S risks in industrial processes: modeling qualitative aspects.

Because of the increase in workplace automation and the diversification of industrial processes, workplaces have become more and more complex. The classical approaches used to address workplace hazard concerns, such as checklists or sequence models, are, therefore, of limited use in such complex systems. Moreover, because of the multifaceted nature of workplaces, the use of single-oriented methods, such as AEA (man oriented), FMEA (system oriented), or HAZOP (process oriented), is not satisfactory. The use of a dynamic modeling approach in order to allow multiple-oriented analyses may constitute an alternative to overcome this limitation. The qualitative modeling aspects of the MORM (man-machine occupational risk modeling) model are discussed in this article. The model, realized on an object-oriented Petri net tool (CO-OPN), has been developed to simulate and analyze industrial processes in an OH&S perspective. The industrial process is modeled as a set of interconnected subnets (state spaces), which describe its constitutive machines. Process-related factors are introduced, in an explicit way, through machine interconnections and flow properties. While man-machine interactions are modeled as triggering events for the state spaces of the machines, the CREAM cognitive behavior model is used in order to establish the relevant triggering events. In the CO-OPN formalism, the model is expressed as a set of interconnected CO-OPN objects defined over data types expressing the measure attached to the flow of entities transiting through the machines. Constraints on the measures assigned to these entities are used to determine the state changes in each machine. Interconnecting machines implies the composition of such flow and consequently the interconnection of the measure constraints. This is reflected by the construction of constraint enrichment hierarchies, which can be used for simulation and analysis optimization in a clear mathematical framework. The use of Petri nets to perform multiple-oriented analysis opens perspectives in the field of industrial risk management. It may significantly reduce the duration of the assessment process. But, most of all, it opens perspectives in the field of risk comparisons and integrated risk management. Moreover, because of the generic nature of the model and tool used, the same concepts and patterns may be used to model a wide range of systems and application fields.

Development of a Subgrade Drainage Model for Unpaved Roads, TR-654, 2015

With over 68 thousand miles of gravel roads in Iowa and the importance of these roads within the farm-to-market transportation system, proper water management becomes critical for maintaining the integrity of the roadway materials. However, the build-up of water within the aggregate subbase can lead to frost boils and ultimately potholes forming at the road surface. The aggregate subbase and subgrade soils under these gravel roads are produced with material opportunistically chosen from local sources near the site and, many times, the compositions of these sublayers are far from ideal in terms of proper water drainage with the full effects of this shortcut not being fully understood. The primary objective of this project was to provide a physically-based model for evaluating the drainability of potential subbase and subgrade materials for gravel roads in Iowa. The Richards equation provided the appropriate framework to study the transient unsaturated flow that usually occurs through the subbase and subgrade of a gravel road. From which, we identified that the saturated hydraulic conductivity, Ks, was a key parameter driving the time to drain of subgrade soils found in Iowa, thus being a good proxy variable for accessing roadway drainability. Using Ks, derived from soil texture, we were able to identify potential problem areas in terms of roadway drainage . It was found that there is a threshold for Ks of 15 cm/day that determines if the roadway will drain efficiently, based on the requirement that the time to drain, Td, the surface roadway layer does not exceed a 2-hr limit. Two of the three highest abundant textures (loam and silty clay loam), which cover nearly 60% of the state of Iowa, were found to have average Td values greater than the 2-hr limit. With such a large percentage of the state at risk for the formation of boils due to the soil with relatively low saturated hydraulic conductivity values, it seems pertinent that we propose alternative design and/or maintenance practices to limit the expensive repair work in Iowa. The addition of drain tiles or French mattresses my help address drainage problems. However, before pursuing this recommendation, a comprehensive cost-benefit analysis is needed.

An assurance-based model to holistically assess the information security posture

EXECUTIVE SUMMARY : Evaluating Information Security Posture within an organization is becoming a very complex task. Currently, the evaluation and assessment of Information Security are commonly performed using frameworks, methodologies and standards which often consider the various aspects of security independently. Unfortunately this is ineffective because it does not take into consideration the necessity of having a global and systemic multidimensional approach to Information Security evaluation. At the same time the overall security level is globally considered to be only as strong as its weakest link. This thesis proposes a model aiming to holistically assess all dimensions of security in order to minimize the likelihood that a given threat will exploit the weakest link. A formalized structure taking into account all security elements is presented; this is based on a methodological evaluation framework in which Information Security is evaluated from a global perspective. This dissertation is divided into three parts. Part One: Information Security Evaluation issues consists of four chapters. Chapter 1 is an introduction to the purpose of this research purpose and the Model that will be proposed. In this chapter we raise some questions with respect to "traditional evaluation methods" as well as identifying the principal elements to be addressed in this direction. Then we introduce the baseline attributes of our model and set out the expected result of evaluations according to our model. Chapter 2 is focused on the definition of Information Security to be used as a reference point for our evaluation model. The inherent concepts of the contents of a holistic and baseline Information Security Program are defined. Based on this, the most common roots-of-trust in Information Security are identified. Chapter 3 focuses on an analysis of the difference and the relationship between the concepts of Information Risk and Security Management. Comparing these two concepts allows us to identify the most relevant elements to be included within our evaluation model, while clearing situating these two notions within a defined framework is of the utmost importance for the results that will be obtained from the evaluation process. Chapter 4 sets out our evaluation model and the way it addresses issues relating to the evaluation of Information Security. Within this Chapter the underlying concepts of assurance and trust are discussed. Based on these two concepts, the structure of the model is developed in order to provide an assurance related platform as well as three evaluation attributes: "assurance structure", "quality issues", and "requirements achievement". Issues relating to each of these evaluation attributes are analysed with reference to sources such as methodologies, standards and published research papers. Then the operation of the model is discussed. Assurance levels, quality levels and maturity levels are defined in order to perform the evaluation according to the model. Part Two: Implementation of the Information Security Assurance Assessment Model (ISAAM) according to the Information Security Domains consists of four chapters. This is the section where our evaluation model is put into a welldefined context with respect to the four pre-defined Information Security dimensions: the Organizational dimension, Functional dimension, Human dimension, and Legal dimension. Each Information Security dimension is discussed in a separate chapter. For each dimension, the following two-phase evaluation path is followed. The first phase concerns the identification of the elements which will constitute the basis of the evaluation: ? Identification of the key elements within the dimension; ? Identification of the Focus Areas for each dimension, consisting of the security issues identified for each dimension; ? Identification of the Specific Factors for each dimension, consisting of the security measures or control addressing the security issues identified for each dimension. The second phase concerns the evaluation of each Information Security dimension by: ? The implementation of the evaluation model, based on the elements identified for each dimension within the first phase, by identifying the security tasks, processes, procedures, and actions that should have been performed by the organization to reach the desired level of protection; ? The maturity model for each dimension as a basis for reliance on security. For each dimension we propose a generic maturity model that could be used by every organization in order to define its own security requirements. Part three of this dissertation contains the Final Remarks, Supporting Resources and Annexes. With reference to the objectives of our thesis, the Final Remarks briefly analyse whether these objectives were achieved and suggest directions for future related research. Supporting resources comprise the bibliographic resources that were used to elaborate and justify our approach. Annexes include all the relevant topics identified within the literature to illustrate certain aspects of our approach. Our Information Security evaluation model is based on and integrates different Information Security best practices, standards, methodologies and research expertise which can be combined in order to define an reliable categorization of Information Security. After the definition of terms and requirements, an evaluation process should be performed in order to obtain evidence that the Information Security within the organization in question is adequately managed. We have specifically integrated into our model the most useful elements of these sources of information in order to provide a generic model able to be implemented in all kinds of organizations. The value added by our evaluation model is that it is easy to implement and operate and answers concrete needs in terms of reliance upon an efficient and dynamic evaluation tool through a coherent evaluation system. On that basis, our model could be implemented internally within organizations, allowing them to govern better their Information Security. RÉSUMÉ : Contexte général de la thèse L'évaluation de la sécurité en général, et plus particulièrement, celle de la sécurité de l'information, est devenue pour les organisations non seulement une mission cruciale à réaliser, mais aussi de plus en plus complexe. A l'heure actuelle, cette évaluation se base principalement sur des méthodologies, des bonnes pratiques, des normes ou des standards qui appréhendent séparément les différents aspects qui composent la sécurité de l'information. Nous pensons que cette manière d'évaluer la sécurité est inefficiente, car elle ne tient pas compte de l'interaction des différentes dimensions et composantes de la sécurité entre elles, bien qu'il soit admis depuis longtemps que le niveau de sécurité globale d'une organisation est toujours celui du maillon le plus faible de la chaîne sécuritaire. Nous avons identifié le besoin d'une approche globale, intégrée, systémique et multidimensionnelle de l'évaluation de la sécurité de l'information. En effet, et c'est le point de départ de notre thèse, nous démontrons que seule une prise en compte globale de la sécurité permettra de répondre aux exigences de sécurité optimale ainsi qu'aux besoins de protection spécifiques d'une organisation. Ainsi, notre thèse propose un nouveau paradigme d'évaluation de la sécurité afin de satisfaire aux besoins d'efficacité et d'efficience d'une organisation donnée. Nous proposons alors un modèle qui vise à évaluer d'une manière holistique toutes les dimensions de la sécurité, afin de minimiser la probabilité qu'une menace potentielle puisse exploiter des vulnérabilités et engendrer des dommages directs ou indirects. Ce modèle se base sur une structure formalisée qui prend en compte tous les éléments d'un système ou programme de sécurité. Ainsi, nous proposons un cadre méthodologique d'évaluation qui considère la sécurité de l'information à partir d'une perspective globale. Structure de la thèse et thèmes abordés Notre document est structuré en trois parties. La première intitulée : « La problématique de l'évaluation de la sécurité de l'information » est composée de quatre chapitres. Le chapitre 1 introduit l'objet de la recherche ainsi que les concepts de base du modèle d'évaluation proposé. La maniéré traditionnelle de l'évaluation de la sécurité fait l'objet d'une analyse critique pour identifier les éléments principaux et invariants à prendre en compte dans notre approche holistique. Les éléments de base de notre modèle d'évaluation ainsi que son fonctionnement attendu sont ensuite présentés pour pouvoir tracer les résultats attendus de ce modèle. Le chapitre 2 se focalise sur la définition de la notion de Sécurité de l'Information. Il ne s'agit pas d'une redéfinition de la notion de la sécurité, mais d'une mise en perspectives des dimensions, critères, indicateurs à utiliser comme base de référence, afin de déterminer l'objet de l'évaluation qui sera utilisé tout au long de notre travail. Les concepts inhérents de ce qui constitue le caractère holistique de la sécurité ainsi que les éléments constitutifs d'un niveau de référence de sécurité sont définis en conséquence. Ceci permet d'identifier ceux que nous avons dénommés « les racines de confiance ». Le chapitre 3 présente et analyse la différence et les relations qui existent entre les processus de la Gestion des Risques et de la Gestion de la Sécurité, afin d'identifier les éléments constitutifs du cadre de protection à inclure dans notre modèle d'évaluation. Le chapitre 4 est consacré à la présentation de notre modèle d'évaluation Information Security Assurance Assessment Model (ISAAM) et la manière dont il répond aux exigences de l'évaluation telle que nous les avons préalablement présentées. Dans ce chapitre les concepts sous-jacents relatifs aux notions d'assurance et de confiance sont analysés. En se basant sur ces deux concepts, la structure du modèle d'évaluation est développée pour obtenir une plateforme qui offre un certain niveau de garantie en s'appuyant sur trois attributs d'évaluation, à savoir : « la structure de confiance », « la qualité du processus », et « la réalisation des exigences et des objectifs ». Les problématiques liées à chacun de ces attributs d'évaluation sont analysées en se basant sur l'état de l'art de la recherche et de la littérature, sur les différentes méthodes existantes ainsi que sur les normes et les standards les plus courants dans le domaine de la sécurité. Sur cette base, trois différents niveaux d'évaluation sont construits, à savoir : le niveau d'assurance, le niveau de qualité et le niveau de maturité qui constituent la base de l'évaluation de l'état global de la sécurité d'une organisation. La deuxième partie: « L'application du Modèle d'évaluation de l'assurance de la sécurité de l'information par domaine de sécurité » est elle aussi composée de quatre chapitres. Le modèle d'évaluation déjà construit et analysé est, dans cette partie, mis dans un contexte spécifique selon les quatre dimensions prédéfinies de sécurité qui sont: la dimension Organisationnelle, la dimension Fonctionnelle, la dimension Humaine, et la dimension Légale. Chacune de ces dimensions et son évaluation spécifique fait l'objet d'un chapitre distinct. Pour chacune des dimensions, une évaluation en deux phases est construite comme suit. La première phase concerne l'identification des éléments qui constituent la base de l'évaluation: ? Identification des éléments clés de l'évaluation ; ? Identification des « Focus Area » pour chaque dimension qui représentent les problématiques se trouvant dans la dimension ; ? Identification des « Specific Factors » pour chaque Focus Area qui représentent les mesures de sécurité et de contrôle qui contribuent à résoudre ou à diminuer les impacts des risques. La deuxième phase concerne l'évaluation de chaque dimension précédemment présentées. Elle est constituée d'une part, de l'implémentation du modèle général d'évaluation à la dimension concernée en : ? Se basant sur les éléments spécifiés lors de la première phase ; ? Identifiant les taches sécuritaires spécifiques, les processus, les procédures qui auraient dû être effectués pour atteindre le niveau de protection souhaité. D'autre part, l'évaluation de chaque dimension est complétée par la proposition d'un modèle de maturité spécifique à chaque dimension, qui est à considérer comme une base de référence pour le niveau global de sécurité. Pour chaque dimension nous proposons un modèle de maturité générique qui peut être utilisé par chaque organisation, afin de spécifier ses propres exigences en matière de sécurité. Cela constitue une innovation dans le domaine de l'évaluation, que nous justifions pour chaque dimension et dont nous mettons systématiquement en avant la plus value apportée. La troisième partie de notre document est relative à la validation globale de notre proposition et contient en guise de conclusion, une mise en perspective critique de notre travail et des remarques finales. Cette dernière partie est complétée par une bibliographie et des annexes. Notre modèle d'évaluation de la sécurité intègre et se base sur de nombreuses sources d'expertise, telles que les bonnes pratiques, les normes, les standards, les méthodes et l'expertise de la recherche scientifique du domaine. Notre proposition constructive répond à un véritable problème non encore résolu, auquel doivent faire face toutes les organisations, indépendamment de la taille et du profil. Cela permettrait à ces dernières de spécifier leurs exigences particulières en matière du niveau de sécurité à satisfaire, d'instancier un processus d'évaluation spécifique à leurs besoins afin qu'elles puissent s'assurer que leur sécurité de l'information soit gérée d'une manière appropriée, offrant ainsi un certain niveau de confiance dans le degré de protection fourni. Nous avons intégré dans notre modèle le meilleur du savoir faire, de l'expérience et de l'expertise disponible actuellement au niveau international, dans le but de fournir un modèle d'évaluation simple, générique et applicable à un grand nombre d'organisations publiques ou privées. La valeur ajoutée de notre modèle d'évaluation réside précisément dans le fait qu'il est suffisamment générique et facile à implémenter tout en apportant des réponses sur les besoins concrets des organisations. Ainsi notre proposition constitue un outil d'évaluation fiable, efficient et dynamique découlant d'une approche d'évaluation cohérente. De ce fait, notre système d'évaluation peut être implémenté à l'interne par l'entreprise elle-même, sans recourir à des ressources supplémentaires et lui donne également ainsi la possibilité de mieux gouverner sa sécurité de l'information.

INDISIM-YEAST, an individual-based model to study yeast

INDISIM-YEAST, an individual-based simulator, models the evolution of a yeast population by settingup rules of behaviour for each individual cell according to their own biological rules and characteristics. Ittakes into account the uptake, metabolism, budding reproduction and viability of the yeast cells, over aperiod of time in the bulk of a liquid medium, occupying a three dimensional closed spatial grid with twokinds of particles (glucose and ethanol). Each microorganism is characterized by its biomass, genealogicalage, states in the budding cellular reproduction cycle and position in the space among others. Simulationsare carried out for population properties (global properties), as well as for those properties that pertain toindividual yeast cells (microscopic properties). The results of the simulations are in good qualitativeagreement with established experimental trends.