Aplicação de técnicas eletroquímicas na determinação do potencial de corrosividade de ligas de alumínio em água produzida

The resistance of aluminum and their alloys, to the corrosion phenomenon, in aqueous solutions, is a result of the oxide layer formed. However, the corrosion process in the aluminum alloy is associated with the presence a second phase of particles or the presence of chloride ions which promote the disruption of the oxide layer located producing the corrosion process. On the other hand, the term water produced is used to describe the water after the separation of the oil and gas in API separators. The volumes of produced water arrive around 5 more times to the volume of oil produced. The greatest feature of the water is the presence of numerous pollutants. Due to the increased volume of waste around the world in the current decade, the outcome and the effect of the discharge of produced water on the environment has recently become an important issue of environmental concern where numerous treatments are aimed at reducing these contaminants before disposal. Then, this study aims to investigate the electrochemical corrosion behavior of aluminum alloy 6060 in presence of water produced and the influence of organic components as well as chloride ions, by using the electrochemical techniques of linear polarization. The modification of the passive layer and the likely breakpoints were observed by atomic force microscopy (AFM). In the pit formation potential around -0.4 to -0.8 V/EAg/AgCl was observed that the diffusion of chloride ions occurs via the layer formed with the probable formation of pits. Whereas, at temperatures above 65 °C, it was observed that the range of potential for thepit formation was -0.4 to -0.5 V/EAg/AgCl. In all reactions, the concentration of Al(OH)3 in the form of a gel was observed

Pirólise de borras oleosas de petroleo utilizando nanomateriais

The oily sludge is a complex mix of hydrocarbons, organic impurities, inorganic and water. One of the major problems currently found in petroleum industry is management (packaging, storage, transport and fate) of waste. The nanomaterials (catalysts) mesoporous and microporous are considered promising for refining and adsorbents process for environment protection. The aim of this work was to study the oily sludge from primary processing (raw and treated) and vacuum residue, with application of thermal analyses technique (pyrolysis), thermal and catalytic pyrolysis with nanomaterials, aiming at production petroleum derived. The sludge and vacuum residue were analyzed using a soxhlet extraction system, elemental analysis, thin layer chromatography, thermogravimetry and pyrolysis coupled in gas chromatography/mass spectrometry (Py GC MS). The catalysts AlMCM-41, AlSBA-15.1 e AlSBA-15.2 were synthesized with molar ratio silicon aluminum of 50 (Si/Al = 50), using tetraethylorthosilicante as source of silicon and pseudobuhemita (AlOOH) as source of aluminum. The analyzes of the catalysts indicate that materials showed hexagonal structure and surface area (783,6 m2/g for AlMCM-41, 600 m2/g for AlSBA-15.1, 377 m2/g for AlSBA-15.2). The extracted oily sludge showed a range 65 to 95% for organic components (oil), 5 to 35% for inorganic components (salts and oxides) and compositions different of derivatives. The AlSBA-15 catalysts showed better performance in analyzes for production petroleum derived, 20% increase in production of kerosene and light gas oil. The energy potential of sludge was high and it can be used as fuel in other cargo processed in refinery

Photoelectrocatalytic oxidation of hair dye basic red 51 at W/WO 3/TiO2 bicomposite photoanode activated by ultraviolet and visible radiation

We prepared a W/WO3/TiO2 bicomposite photoanode by simple electrochemical anodization of W foil, followed by cathodic electrodeposition of TiO2 and annealing at 450 C for 30 min. This photoanode shows good photoactivity under irradiation with UV and visible light. In optimized conditions, it promotes complete photoelectrocatalytic oxidation of 3.33 × 10-5 mol L-1 basic red 51 solution (which is used in hair dye) at 0.1 mol L-1 Na2SO4, pH 2.0, under a current density of 1.25 mA cm-2 and ultraviolet and visible radiation-total organic carbon removal is 94 and 88%, respectively. This effect paves the way for the sustainable solar-assisted remediation of water bodies contaminated with organic components of hair dyes. © 2013 Elsevier Ltd. All rights reserved.

Kinetic study of pyrolysis of castor beans (Ricinuscommunis L) presscake: an alternative use for solid waste arising from the biodiesel production

This work investigated the effects of temperature and of rate of heating on the kinetic parameters of pyrolysis of castor beans presscake, a byproduct generated in the biodiesel production process. Pyrolysis process was investigated by thermogravimetric analysis, and parameters were obtained from nonisothermal experiments. The results obtained from the process of thermal decomposition indicated the elimination of humidity and the decomposition of organic components of the biomass. DTG curves showed that the heating rate affects the temperature of maximum decomposition of the material. Kinetic parameters such as activation energy and pre-exponential factor were obtained by model-free methods proposed by Flynn–Wall–Ozawa (FWO), Kissinger–Akahira–Sunose (KAS), and Kissinger. Experimental results showed that the kinetic parameters values of the FWO and KAS methods display good agreement and can be used to understand the mechanism of degradation of the cake. In a generalized way, the results contribute to better understanding of the processes of biomass pyrolysis.

Nanocompósito de alumina com inclusão nonométricas de zircônia para infraestruturas de próteses odontológicas livres de metal: avaliação de prosperidades mecânicas e análise microestrutural. -

Pós-graduação em Reabilitação Oral - FOAR

Free radical entrapment and crystallinity of resin composites after accelerated aging as a function of the expiration date

This study evaluated the spin concentration and the crystallinity in different classifications of dental composites as a function of the material condition (new, aged and expired). Specimens were obtained according to the factors: composites: Filtek P60, Filtek Z250, Filtek Z350XT, and Filtek Silorane; and material conditions: new, aged, and expired. The syringe composites underwent an accelerated aging protocol (Arrhenius model). The magnetic properties of the composites were characterized using Electron Paramagnetic Resonance (EPR) and the concentration of spins (number of spins/mass) was calculated. The crystallinity of the composites tested was characterized with X-ray diffraction (XRD). Filtek P60 and Filtek Z250 presented similarities in terms of spin concentration and crystallinity, irrespective of the material condition. The aging protocol influenced the composite Filmic Z350XT that exhibited a significant increase in the spin concentration. Besides, lower intensity peaks of the organic matrix and amorphous silica were also observed for both aged and expired Filtek Z350XT. Although a significant lower spin concentration was observed for the silorane composite in comparison to that of the methacrylates, a decrease in the relative intensity of peaks of the amorphous region related to the organic components in the diffractograms was observed. The material conditions tested influence the crystallinity and the magnetic properties of the composites evaluated. (C) 2014 Elsevier Ltd. All rights reserved.

Preparação e caracterização de novos híbridos orgânicos-inorgânicos baseados em carboximetilcelulose/polifosfato de sódio dopados com 'Eu'Cl IND.3

Organic- inorganic hybrid (HOI) are materials prepared with the combination of inorganic and organic components. The properties of a hybrid material are unique, not being the sum of each individual component added. This occurs because there is a synergism that depends of the chemical nature of organic and inorganic components, of the size and morphology of their domains. The sodium carboxymethylcellulose (CMC) it's an anionic polymer obtained of the cellulose, very soluble in water in which forms both solutions themselves and gels. The sodium polyphosphate (NaPO3)n, known commercially as Graham Salt is the only polyphosphate soluble in water, and it's the polyphosphate with the longest chain. At the present work it was prepared and characterized new phosphate organic- inorganic hybrids films of carboxymethylcellulose / sodium phosphate and luminescent films of CMC/NaPO3 doped with europium chloride (EuCl3). The films where prepared in several proportions. At first, it was set the amount of water to be used and the amount of carboxymethylcellulose, changing the concentrations of sodium polyphosphate and europium chloride. After pre-establishing concentrations, for each film, the components were submitted to constant agitation and subsequent drying. The inorganic-organic hybrid films were characterized by, TG, DR-X, DMA, FT-IR, UV-Vis-NIR, RMN 31P e 13C and at last, a study of luminescence was made. The hybrid films obtained are transparent and macroscopically homogeneous, however, the MET measures showed the formation of micro-islands of polyphosphate along the material, this fact indicates a bigger fragmentation of the films and this is verified by DMA analysis which shows a smaller resistance of the film with the increase of the concentration of phosphate. Both spectrum FT-IR and RMN analysis of the films, don't show the formation of new bands of their precursors, CMC e NaPO3,....

Avaliação do processo de contaminação e remediação de água subterrânea por hidrocarbonetos

Pós-graduação em Engenharia Civil e Ambiental - FEB

Utilização de extratos vegetais em proteção de plantas

Usage of pesticies in excessive doses or in an inadequate way to control diseases, pests and weeds, has promoted significant environmental damage, contamination of animals, intoxication of farmers, among others. These factors lead to occur the resistance of weeds, pests and pathogens, the appearance of iatrogenic diseases, biological imbalance and reduction in biodiversity. Seeking less aggressive alternatives, plant extracts have been used successfully. Compared to synthetic products, they offer great advantages as generating new compounds, which pathogens are unable to inactivate, and are less toxic, of rapid degradation in the environment, they have broad modes of action, and are derived from renewable resources. It should be emphasized that there are some limitations on its use. The extracts have potencial as insecticide, fungicide, herbicide and nematicide and are considered of good efficiency. The methodologies for obtaining can be achieved through cold extraction, open and closed hot system. The use of plant extracts reappears as a promising and unique option for integrated management in plant protection, being considered as an alternative to control plant pathogens, demonstrating excellent results without causing harm to the environment and living beings.

ANALYSIS OF MANGROVE FOREST SUCCESSION, USING SEDIMENT CORES: A CASE STUDY IN THE CANANEIA-IGUAPE COASTAL SYSTEM, SAO PAULO-BRAZIL

Sediment cores are an essential tool for the analysis of the dynamics of mangrove succession. Coring was used to correlate changes in depositional environments and lateral sedimentary facies with discrete stages of forest succession at the Cananeia-Iguape Coastal System in southeastern Brazil. A local level successional pattern was examined based on four core series T1) a sediment bank; T2) a smooth cordgrass Spartina alterniflora bank; T3) an active mangrove progradation fringe dominated by Laguncularia racemosa, and; T4) a mature mangrove forest dominated by Avicennia schaueriana. Cores were macroscopically described in terms of color, texture, sedimentary structure and organic components. The base of all cores exhibited a similar pattern suggesting common vertical progressive changes in depositional conditions and subsequent successional colonization pattern throughout the forest. The progradation zone is an exposed bank, colonized by S. alterniflora. L. racemosa, replaces S. alterniflora as progradation takes place. As the substrate consolidates A. schaueriana replaces L. racemosa and attains the greatest structural development in the mature forest. Cores collected within the A. schaueriana dominated stand contained S. alterniflora fragments near the base, confirming that a smooth cordgrass habitat characterized the establishment and early seral stages. Cores provide a reliable approach to describe local-level successional sequences in dynamic settings subject to drivers operating on multiple temporal and spatial scales where spatial heterogeneity can lead to multiple equilibria and where similar successional end-points may be reached through convergent paths.

Chemically Resolved Particle Fluxes Over Tropical and Temperate Forests

Chemically resolved submicron (PM1) particlemass fluxes were measured by eddy covariance with a high resolution time-of-flight aerosolmass spectrometer over temperate and tropical forests during the BEARPEX-07 and AMAZE-08 campaigns. Fluxes during AMAZE-08 were small and close to the detection limit (<1 ng m−2 s−1) due to low particle mass concentrations (<1 μg m−3). During BEARPEX-07, concentrations were five times larger, with mean mid-day deposition fluxes of −4.8 ng m−2 s−1 for total nonrefractory PM1 (Vex,PM1 = −1 mm s−1) and emission fluxes of +2.6 ng m−2 s−1 for organic PM1 (Vex,org = +1 mm s−1). Biosphere–atmosphere fluxes of different chemical components are affected by in-canopy chemistry, vertical gradients in gas-particle partitioning due to canopy temperature gradients, emission of primary biological aerosol particles, and wet and dry deposition. As a result of these competing processes, individual chemical components had fluxes of varying magnitude and direction during both campaigns. Oxygenated organic components representing regionally aged aerosol deposited, while components of fresh secondary organic aerosol (SOA) emitted. During BEARPEX-07, rapid incanopy oxidation caused rapid SOA growth on the timescale of biosphere-atmosphere exchange. In-canopy SOA mass yields were 0.5–4%. During AMAZE-08, the net organic aerosol flux was influenced by deposition, in-canopy SOA formation, and thermal shifts in gas-particle partitioning.Wet deposition was estimated to be an order ofmagnitude larger than dry deposition during AMAZE-08. Small shifts in organic aerosol concentrations from anthropogenic sources such as urban pollution or biomass burning alters the balance between flux terms. The semivolatile nature of the Amazonian organic aerosol suggests a feedback in which warmer temperatures will partition SOA to the gas-phase, reducing their light scattering and thus potential to cool the region.

Morphologischer und biochemischer Aufbau von Silikatnadeln der Hexactinelliden am Beispiel von Monorhaphis chuni

Schon 1904 beschrieb Schulze den Aufbau von Silikatnadeln des Schwammes Monorhaphis chuni, eines Mitglieds der zweiten Familie von biosilifizierenden Schwämmen, den Hexactinelliden (Glasschwämmen). Weitergehende morphologische Untersuchungen und biochemische Analysen insbesondere mit modernen Methoden wurden an Hexactinelliden bisher kaum durchgeführt. Ziel der vorliegenden Arbeit bestand deshalb darin, Untersuchungen zur Morphologie, der chemischen Zusammensetzung, der Verteilung und Charakterisierung der beteiligten anorganischen und organischen Komponenten sowie einen molekularbiologischer Nachweis der Existenz von Silicatein in Hexactinelliden durchzuführen. Für diese Untersuchungen wurden zwei Spezies verwendet: Monorhaphis chuni und Crateromorpha meyeri. Mittels Elektronen-Mikrosonden-Technik wurde an Querschnitten der Pfahlnadel von M. chuni die Verteilung der Elemente innerhalb der Nadel untersucht. Am äußeren Rand der Nadel (150 µm) traten im Vergleich zur Nadelmitte prägnante Unterschiede in der Konzentration von Kaliumoxid und Natriumoxid auf. Diese Ergebnisse deuten auf das Vorhandensein eines ähnlichen Transportsystems zur Anreicherung von Silizium/Silikat bei der Nadelbildung hin, wie es bereits in S. domuncula bekannt ist. Mit elektronen- und lichtmikroskopischen Untersuchungen wurden die organischen Substanzen der Silikatnadel nachgewiesen und deren Verteilung innerhalb dieser Nadeln analysiert. In der lamellaren Zone befindet sich, eine säurelabile organische Netzstruktur, sowie eine, die Silikatschichten durchspannende, säulenähnliche Struktur. Im Axialzylinder zeigt das organische Material eine leicht verzweigte fibrilläre Anordnung. Mit biochemischen Verfahren wurden die organischen Komponenten der Nadeln detaillierter untersucht. Mehrere Proteine mit Molekulargewichten von 17, 24, 27 ,30, 36 und 70 kDa wurden durch gelelektrophoretische Analysen von Material der Pfahlnadel identifiziert. Die Analyse isolierter Anteile der lamellaren Zone zeigte ausschließlich ein 27 kDa Protein. Die restlichen Proteinbanden konnten hier nicht nachgewiesen werden. Das 27 kDa Protein reagierte im Westernblot mit Antikörpern gegen Silicatein aus S. domuncula. Ein weiteres Protein wurde näher charakterisert. Ein positiver Agglutinationsassay wies ein lectinähnliches Molekül innerhalb der Nadeln nach, wie es aus S. domuncula bekannt ist. Nach einer Deglycolysierung der Proteine reduzierte sich das scheinbare Molekulargewicht der 36 kDa Bande auf 30 kDa. Durch molekularbiologische Untersuchungen wurde erstmals in Hexactinelliden die Existenz von Silicatein nachgewiesen. Nach Isolierung der Gesamt-RNA von Crateromorpha meyeri, RT-PCR und Amplifizierung mit silicateinspezifischen Primern wurde eine 549 kBp Nukleotidsequenz gefunden, die auf Aminosäureebene starke Homologien (76% identische Aminosäuren) zu bekannten Silicateinen der Demospongia aufweist. Die Aminosäuren der katalytische Triade des Silicateins, essenziell für die enzymatische Katalyse des Enzyms, sind an den selben Positionen wie bei bekannten Silicateinen vorhanden.

Preparation and functional characterisation of recombinant silicatein-alpha from the sponge Suberites domuncula

The marine world is an immense source of biodiversity that provides substances with striking potentials in medicinal chemistry and biotechnology. Sponges (Porifera) are marine animals that represent the most impressive example of organisms possessing the ability to metabolise silica through a family of enzymes known as silicateins. Complex skeletal structures (spicules) made of pure biogenic silica (biosilica) are produced under physiological conditions. Biosilica is a natural material comprising inorganic and organic components with unique mechanical, optical, and physico-chemical properties, including promising potential to be used for development of therapeutic agents in regenerative medicine. Unravelling the intimate physiological mechanisms occurring in sponges during the construction of their siliceous spicules is an on-going project, and several questions have been addressed by the studies proposed by our working group. In this doctoral work, the recombinant DNA technology is exploited for functional and structural characterisation of silicatein. Its precursors are produced as fusion proteins with a chaperone tag (named TF-Ps), and a robust method for the overexpression of native soluble proteins in high concentrations has been developed. In addition, it is observed and proven experimentally that the maturation of silicatein is an autocatalytic event that: (i) can be modulated by rational use of protease inhibitors; (ii) is influenced by the temperature of the environment; (iii) only slightly depends on the pH. In the same experimental framework, observations on the dynamics in the maturation of silicateins allow a better understanding of how the axial filaments form during the early stages of spicule construction. In addition, the definition of new distinct properties of silicatein (termed “structure-guiding” and “structure-forming”) is introduced. By homology models and through comparisons with similar proteins (the cathepsins), domains with significant surface hydrophobicity are identified as potential self-assembly mediators. Moreover, a high-throughput screening showed that TF-Ps could generate crystals under certain conditions, becoming promising for further structural studies. With the goal of optimise the properties of the recombinant silicatein, implementation of new production systems are tried for the first time. Success in the expression of silicatein-type proteins in insect and yeast cells, constitute a promising basis for further development, towards the establishment of an efficient method for the production of a high-value pure and soluble protein.

Table 1 Microorganisms, identified with DOGE analysis. 16S rDNA sequences, obtained from sequencing of DOGE bands, were assigned to the corresponding microorganisms

Microorganisms play an important role in the transformation of material within the earth's crust. The storage of CO2 could affect the composition of inorganic and organic components in the reservoir, consequently influencing microbial activities. To study the microbial induced processes together with geochemical, petrophysical and mineralogical changes, occurring during CO2 storage, long-term laboratory experiments under simulated reservoir P-T conditions were carried out. Clean inner core sections, obtained from the reservoir region at the CO2 storage site in Ketzin (Germany) from a depth of about 650 m, were incubated in high pressure vessels together with sterile synthetic formation brine under in situ P-T conditions of 5.5 MPa and 40°C. A 16S rDNA based fingerprinting method was used to identify the dominant species in DNA extracts of pristine sandstone samples. Members of the alpha- and beta-subdivisions of Proteobacteria and the Actinobacteria were identified. So far sequences belonging to facultative anaerobic, chemoheterotrophic bacteria (Burkholderia fungorum, Agrobacterium tumefaciens) gaining their energy from the oxidation of organic molecules and a genus also capable of chemolithoautotrophic growth (Hydrogenophaga) was identified. During CO2 incubation minor changes in the microbial community composition were observed. The majority of microbes were able to adapt to the changed conditions. During CO2 exposure increased concentrations of Ca**2+, K**+, Mg**2+ and SO4**2- were observed. Partially, concentration rises are (i) due to equilibration between rock pore water and synthetic brine, and (ii) between rock and brine, and are thus independent on CO2 exposure. However, observed concentrations of Ca**2+, K**+, Mg**2+ are even higher than in the original reservoir fluid and therefore indicate mineral dissolution due to CO2 exposure.

Lipid biomarkers in urface sediments of the Southeast Atlantic

Surface sediments from the eastern South Atlantic were investigated for their lipid biomarker contents and bulk organic geochemical characteristics to identify sources, transport pathways and preservation processes of organic components. The sediments cover a wide range of depositional settings with large differences in mass accumulation rates. The highest marine organic carbon (OC) contributions are detected along the coast, especially underlying the Benguela upwelling system. Terrigenous OC contributions are highest in the Congo deep-sea fan. Lipid biomarker fluxes are significantly correlated to the extent of oxygen exposure in the sediment. Normalization to total organic carbon (TOC) contents enabled the characterization of regional lipid biomarker production and transport mechanisms. Principal component analyses revealed five distinct groups of characteristic molecular and bulk organic geochemical parameters. Combined with information on lipid sources, the main controlling mechanisms of the spatial lipid distributions in the surface sediments are defined, indicating marine productivity related to river-induced mixing and oceanic upwelling, wind-driven deep upwelling, river-supply of terrigenous organic material, shallow coastal upwelling and eolian supply of plant-waxes.