Effect of boron addition and processing of Ti-6Al-4V on corrosion behaviour and biocompatibility

Ti-6Al-4V is widely used to prepare biomedical implant for orthopaedic and dental applications, but it is an expensive choice relative to other implant materials such as stainless steels and Co-Cr alloys, in large part due to the high manufacturing cost. Adding boron to refine the as cast microstructure of Ti-6Al-4V can eliminate the need for extensive hot working and thereby reduce processing costs. The effect of 0.1 wt-% boron addition and the choice of processing route (forging or extrusion) was studied in the context of potential biomedical applications. Corrosion tests in simulated body fluid indicated that the presence of boron increased the corrosion rate of Ti-6Al-4V and that the increase was higher for forged alloys than for extruded alloys. Boron addition and processing route were found to have a minimal effect on the viability of osteoblasts on the alloy surfaces. It is concluded that the addition of boron could offer advantages during the processing of Ti-6Al-4V for biomedical applications.

Nonlinear viscoelasticity of entangled wormlike micellar fluid under large-amplitude oscillatory shear: Role of elastic Taylor-Couette instability

The role of elastic Taylor-Couette flow instabilities in the dynamic nonlinear viscoelastic response of an entangled wormlike micellar fluid is studied by large-amplitude oscillatory shear (LAOS) rheology and in situ polarized light scattering over a wide range of strain and angular frequency values, both above and below the linear crossover point. Well inside the nonlinear regime, higher harmonic decomposition of the resulting stress signal reveals that the normalized third harmonic I-3/I-1 shows a power-law behavior with strain amplitude. In addition, I-3/I-1 and the elastic component of stress amplitude sigma(E)(0) show a very prominent maximum at the strain value where the number density (n(v)) of the Taylor vortices is maximum. A subsequent increase in applied strain (gamma) results in the distortions of the vortices and a concomitant decrease in n(v), accompanied by a sharp drop in I-3 and sigma(E)(0). The peak position of the spatial correlation function of the scattered intensity along the vorticity direction also captures the crossover. Lissajous plots indicate an intracycle strain hardening for the values of gamma corresponding to the peak of I-3, similar to that observed for hard-sphere glasses.

Wall-mode instability in plane shear flow of viscoelastic fluid over a deformable solid

The linear stability analysis of a plane Couette flow of an Oldroyd-B viscoelastic fluid past a flexible solid medium is carried out to investigate the role of polymer addition in the stability behavior. The system consists of a viscoelastic fluid layer of thickness R, density rho, viscosity eta, relaxation time lambda, and retardation time beta lambda flowing past a linear elastic solid medium of thickness HR, density rho, and shear modulus G. The emphasis is on the high-Reynolds-number wall-mode instability, which has recently been shown in experiments to destabilize the laminar flow of Newtonian fluids in soft-walled tubes and channels at a significantly lower Reynolds number than that for flows in rigid conduits. For Newtonian fluids, the linear stability studies have shown that the wall modes become unstable when flow Reynolds number exceeds a certain critical value Re c which scales as Sigma(3/4), where Reynolds number Re = rho VR/eta, V is the top-plate velocity, and dimensionless parameter Sigma = rho GR(2)/eta(2) characterizes the fluid-solid system. For high-Reynolds-number flow, the addition of polymer tends to decrease the critical Reynolds number in comparison to that for the Newtonian fluid, indicating a destabilizing role for fluid viscoelasticity. Numerical calculations show that the critical Reynolds number could be decreased by up to a factor of 10 by the addition of small amount of polymer. The critical Reynolds number follows the same scaling Re-c similar to Sigma(3/4) as the wall modes for a Newtonian fluid for very high Reynolds number. However, for moderate Reynolds number, there exists a narrow region in beta-H parametric space, corresponding to very dilute polymer solution (0.9 less than or similar to beta < 1) and thin solids (H less than or similar to 1.1), in which the addition of polymer tends to increase the critical Reynolds number in comparison to the Newtonian fluid. Thus, Reynolds number and polymer properties can be tailored to either increase or decrease the critical Reynolds number for unstable modes, thus providing an additional degree of control over the laminar-turbulent transition.

Damping of Vertically Excited Surface Wave in Weakly Viscous Fluid

In a vertically oscillating circular cylindrical container, singular perturbation theory of two-time scale expansions is developed in weakly viscous fluids to investigate the motion of single free surface standing wave by linearizing the Navier-Stokes equation. The fluid field is divided into an outer potential flow region and an inner boundary layer region. The solutions of both two regions are obtained and a linear amplitude equation incorporating damping term and external excitation is derived. The condition to appear stable surface wave is obtained and the critical curve is determined. In addition, an analytical expression of damping coefficient is determined. Finally, the dispersion relation, which has been derived from the inviscid fluid approximation, is modified by adding linear damping. It is found that the modified results are reasonably closer to experimental results than former theory. Result shows that when forcing frequency is low, the viscosity of the fluid is prominent for the mode selection. However, when forcing frequency is high, the surface tension of the fluid is prominent.

Progress In Modeling Of Fluid Flows In Crystal Growth Processes

Modeling of fluid flows in crystal growth processes has become an important research area in theoretical and applied mechanics. Most crystal growth processes involve fluid flows, such as flows in the melt, solution or vapor. Theoretical modeling has played an important role in developing technologies used for growing semiconductor crystals for high performance electronic and optoelectronic devices. The application of devices requires large diameter crystals with a high degree of crystallographic perfection, low defect density and uniform dopant distribution. In this article, the flow models developed in modeling of the crystal growth processes such as Czochralski, ammonothermal and physical vapor transport methods are reviewed. In the Czochralski growth modeling, the flow models for thermocapillary flow, turbulent flow and MHD flow have been developed. In the ammonothermal growth modeling, the buoyancy and porous media flow models have been developed based on a single-domain and continuum approach for the composite fluid-porous layer systems. In the physical vapor transport growth modeling, the Stefan flow model has been proposed based on the flow-kinetics theory for the vapor growth. In addition, perspectives for future studies on crystal growth modeling are proposed. (c) 2008 National Natural Science Foundation of China and Chinese Academy of Sciences. Published by Elsevier Limited and Science in China Press. All rights reserved.

Design of a Sensor Based on Plastic Optical Fibre (POF) to Measure Fluid Flow and Turbidity

Although many optical fibre applications are based on their capacity to transmit optical signals with low losses, it can also be desirable for the optical fibre to be strongly affected by a certain physical parameter in the environment. In this way, it can be used as a sensor for this parameter. There are many strong arguments for the use of POFs as sensors. In addition to being easy to handle and low cost, they demonstrate advantages common to all multimode optical fibres. These specifically include flexibility, small size, good electromagnetic compatibility behaviour, and in general, the possibility of measuring any phenomenon without physically interacting with it. In this paper, a sensor based on POF is designed and analysed with the aim of measuring the volume and turbidity of a low viscosity fluid, in this case water, as it passes through a pipe. A comparative study with a commercial sensor is provided to validate the proven flow measurement. Likewise, turbidity is measured using different colour dyes. Finally, this paper will present the most significant results and conclusions from all the tests which are carried out.

Space experimental studies of microgravity fluid science in China

Microgravity fluid physics is an important part of microgravity sciences, which consists of simple fluids of many new systems, gas-liquid two-phase flow and heat transfer, and complex fluid mechanics. In addition to the importance of itself in sciences and applications, microgravity fluid physics closely relates to microgravity combustion, space biotechnology and space materials science, and promotes the developments of interdisciplinary fields. Many space microgravity experiments have been per- formed on board the recoverable satellites and space ships of China and pushed the rapid development of microgravity sciences in China. In the present paper, space experimental studies and the main re- sults of the microgravity fluid science in China in the last 10 years or so are introduced briefly.

Fluid-structure Interactions of Inverted Leaves and Flags

Interactions between fluid flows and elastic bodies are ubiquitous in nature. One such phenomena that is encountered on a daily basis is the flapping and fluttering of leaves in the wind. The fluid-structure interaction that governs the physics of a leaf in the wind is poorly understood at best and has potential applications in biomechanics, vehicle design, and energy conversion. We build upon previous work on the flapping dynamics of inverted flags, which are cantilevered elastic sheets with free leading edge and fixed trailing edge that display unique large amplitude oscillatory behaviors. We model a leaf in the laboratory using modified inverted flags, experimentally probing the governing parameters behind leaf fluttering as well as shedding light on the physics behind the inverted flag phenomena. The behavior of these "inverted leaves" studied here display sensitive dependence on two biomechanically relevant parameters, stem-to-leaf rigidity and stem-to-leaf length. In addition, leaves on a tree are not often found alone. We seek to understand the complex interactions of multiple fluttering and flapping leaves by way of examining the interactions between pairs of inverted flags. Coupling through their flow fields, pairs of inverted flags exhibit striking emergent phenomena. We report these observed dynamical behaviors and the conditions upon which they arise.

Eccentricity effects on acoustic radiation from a spherical source suspended within a thermoviscous fluid sphere.

Acoustic radiation from a spherical source undergoing angularly periodic axisymmetric harmonic surface vibrations while eccentrically suspended within a thermoviscous fluid sphere, which is immersed in a viscous thermally conducting unbounded fluid medium, is analyzed in an exact fashion. The formulation uses the appropriate wave-harmonic field expansions along with the translational addition theorem for spherical wave functions and the relevant boundary conditions to develop a closed-form solution in form of infinite series. The analytical results are illustrated with a numerical example in which the vibrating source is eccentrically positioned within a chemical fluid sphere submerged in water. The modal acoustic radiation impedance load on the source and the radiated far-field pressure are evaluated and discussed for representative values of the parameters characterizing the system. The proposed model can lead to a better understanding of dynamic response of an underwater acoustic lens. It is equally applicable in miniature transducer analysis and design with applications in medical ultrasonics.

Multi-objective optimization of a fluid structure interaction benchmarking

The integration and application of a new multi-objective tabu search optimization algorithm for Fluid Structure Interaction (FSI) problems are presented. The aim is to enhance the computational design process for real world applications and to achieve higher performance of the whole system for the four considered objectives. The described system combines the optimizer with a well established FSI solver which is based on the fully implicit, monolithic formuFlation of the problem in the Arbitrary Lagrangian-Eulerian FEM approach. The proposed solver resolves the proposed uid-structure interaction benchmark which describes the self-induced elastic deformation of a beam attached to a cylinder in laminar channel ow. The optimized ow characteristics of the aforementioned geometrical arrangement illustrate the performance of the system in two dimensions. Special emphasis is given to the analysis of the simulation package, which is of high accuracy and is the core of application. The design process identifies the best combination of ow features for optimal system behavior and the most important objectives. In addition, the presented methodology has the potential to run in parallel, which will significantly speed-up the elapsed time. Finite Element Method (FEM), Fluid-Structure Interaction (FSI), Multi-Ojective Tabu search (MOTS2). Copyright © 2013 Tech Science Press.

A fixed-grid b-spline finite element technique for fluid-structure interaction

We present a fixed-grid finite element technique for fluid-structure interaction problems involving incompressible viscous flows and thin structures. The flow equations are discretised with isoparametric b-spline basis functions defined on a logically Cartesian grid. In addition, the previously proposed subdivision-stabilisation technique is used to ensure inf-sup stability. The beam equations are discretised with b-splines and the shell equations with subdivision basis functions, both leading to a rotation-free formulation. The interface conditions between the fluid and the structure are enforced with the Nitsche technique. The resulting coupled system of equations is solved with a Dirichlet-Robin partitioning scheme, and the fluid equations are solved with a pressure-correction method. Auxiliary techniques employed for improving numerical robustness include the level-set based implicit representation of the structure interface on the fluid grid, a cut-cell integration algorithm based on marching tetrahedra and the conservative data transfer between the fluid and structure discretisations. A number of verification and validation examples, primarily motivated by animal locomotion in air or water, demonstrate the robustness and efficiency of our approach. © 2013 John Wiley & Sons, Ltd.

Non-relativistic conformal symmetries in fluid mechanics

The symmetries of a free incompressible fluid span the Galilei group, augmented with independent dilations of space and time. When the fluid is compressible, the symmetry is enlarged to the expanded Schrodinger group, which also involves, in addition, Schrodinger expansions. While incompressible fluid dynamics can be derived as an appropriate non-relativistic limit of a conformally invariant relativistic theory, the recently discussed conformal Galilei group, obtained by contraction from the relativistic conformal group, is not a symmetry. This is explained by the subtleties of the non-relativistic limit.

Modelling meso-scale diffusion processes in stochastic fluid bio-membranes

The space–time dynamics of rigid inhomogeneities (inclusions) free to move in a randomly fluctuating fluid bio-membrane is derived and numerically simulated as a function of the membrane shape changes. Both vertically placed (embedded) inclusions and horizontally placed (surface) inclusions are considered. The energetics of the membrane, as a two-dimensional (2D) meso-scale continuum sheet, is described by the Canham–Helfrich Hamiltonian, with the membrane height function treated as a stochastic process. The diffusion parameter of this process acts as the link coupling the membrane shape fluctuations to the kinematics of the inclusions. The latter is described via Ito stochastic differential equation. In addition to stochastic forces, the inclusions also experience membrane-induced deterministic forces. Our aim is to simulate the diffusion-driven aggregation of inclusions and show how the external inclusions arrive at the sites of the embedded inclusions. The model has potential use in such emerging fields as designing a targeted drug delivery system.

Caseinolytic activity in gingival crevicular fluid from periodontitis patients

Introduction: Protease activity is essential for the progression of periodontal disease and several studies have shown that gingival crevicular fluid (GCF) proteases are associated with the attachment loss and bone destruction associated with periodontial disease. In addition to measuring protease levels using ELISA, it is also important to consider enzyme activity which can be measured using appropriate substrates. Aim: The aim of this work was to measure the proteolyitc activity in gingival crevicular fluid (GCF) from periodontitis patients using zymography and a fluorogenic protease substrate. Materials and Methods: Twenty four GCF samples were collected from patients with established periodontitis who had not received any periodontal treatment in the previous six months. A strip of perio-paper was inserted into the gingival crevice until light resistance was felt. After 30 seconds the perio-paper was removed and placed into 500 ul ice cold 0.01M sodium phosphate buffer, pH 7.2, containing 0.15M sodium chloride, vortex mixed for 30 seconds and stored at -80°C until required. GCF samples (10 ul) were electrophoresed on 4-16% Blue casein zymogram gels at 125V constant voltage for 90 min. Following electrophoresis the gel was washed in renaturation buffer for 30 min and then placed in developing buffer overnight. Areas of protease activity appeared as clear bands against a blue background. The total caseinolytic activity of each GCF sample was measured using a fluorescent assay with resorufin-labelled casein as the substrate. Results: The results showed that both casein zymography and fluorogenic assay methods were suitable for analysing caseinolytic activity in GCF samples from periodontitis patients. Caseinolytic activity was variable in the periodontitis samples studied and may reflect the episodic nature of the disease. Conclusion: Casein zymography and fluorogenic assay methods may be useful in future attempts to measure active episodes of periodontal disease.

Metabonomics of human amniotic fluid for prenatal diagnostics

O trabalho apresentado nesta tese teve como principais objectivos contribuir para o conhecimento da composição do líquido amniótico humano (LA), colhido no 2º trimestre de gravidez, assim como investigar possíveis alterações na sua composição devido à ocorrência de patologias pré-natais, recorrendo à metabonómica e procurando, assim, definir novos biomarcadores de doenças da grávida e do feto. Após uma introdução descrevendo o estado da arte relacionado com este trabalho (Capítulo 1) e os princípios das metodologias analíticas usadas (Capítulo 2), seguida de uma descrição dos aspectos experimentais associados a esta tese (Capítulo 3), apresentam-se os resultados da caracterização da composição química do LA (gravidez saudável) por espectroscopia de ressonância magnética nuclear (RMN), assim como da monitorização da sua estabilidade durante o armazenamento e após ciclos de congelamento-descongelamento (Capítulo 4). Amostras de LA armazenadas a -20°C registaram alterações significativas, tornando-se estas menos pronunciadas (mas ainda mensuráveis) a -70°C, temperatura recomendada para o armazenamento de LA. Foram também observadas alterações de composição após 1-2 ciclos de congelamento-descongelamento (a ter em conta aquando da reutilização de amostras), assim como à temperatura ambiente (indicando um período máximo de 4h para a manipulação e análise de LA). A aquisição de espectros de RMN de 1H de alta resolução e RMN acoplado (LC-NMR/MS) permitiu a detecção de 75 compostos no LA do 2º trimestre, 6 dos quais detectados pela primeira vez no LA. Experiências de difusão (DOSY) permitiram ainda a caracterização das velocidades de difusão e massas moleculares médias das proteínas mais abundantes. O Capítulo 5 descreve o estudo dos efeitos de malformações fetais (FM) e de cromossomopatias (CD) na composição do LA do 2º trimestre de gravidez. A extensão deste trabalho ao estudo dos efeitos de patologias no LA que ocorrem no 3º trimestre de gravidez é descrita no Capítulo 6, nomeadamente no que se refere ao parto pré-termo (PTD), pré-eclampsia (PE), restrição do crescimento intra-uterino (IUGR), ruptura prematura de membranas (PROM) e diabetes mellitus gestacional (GDM). Como complemento a estes estudos, realizou-se uma análise preliminar da urina materna do 2º trimestre para o estudo de FM e GDM, descrita no Capítulo 7. Para interpretação dos dados analíticos, obtidos por espectroscopia RMN de 1H, cromatografia líquida de ultra eficiência acoplada a espectrometria de massa (UPLC-MS) e espectroscopia do infravermelho médio (MIR), recorreu-se à análise discriminante pelos métodos dos mínimos quadrados parciais e o método dos mínimos quadrados parciais ortogonal (PLS-DA e OPLS-DA) e à correlação espectral. Após análise por validação cruzada de Monte-Carlo (MCCV), os modelos PLS-DA de LA permitiram distinguir as FM dos controlos (sensibilidades 69-85%, especificidades 80-95%, taxas de classificação 80-90%), revelando variações metabólicas ao nível do metabolismo energético, dos metabolismos dos aminoácidos e glícidos assim como possíveis alterações ao nível do funcionamento renal. Observou-se também um grande impacto das FM no perfil metabólico da urina materna (medido por UPLC-MS), tendo no entanto sido registados modelos PLS-DA com menor sensibilidade (40-60%), provavelmente devido ao baixo número de amostras e maior variabilidade da composição da urina (relativamente ao LA). Foram sugeridos possíveis marcadores relacionados com a ocorrência de FM, incluindo lactato, glucose, leucina, valina, glutamina, glutamato, glicoproteínas e conjugados de ácido glucurónico e/ou sulfato e compostos endógenos e/ou exógenos (<1 M) (os últimos visíveis apenas na urina). No LA foram também observadas variações metabólicas devido à ocorrência de vários tipos de cromossomopatias (CD), mas de menor magnitude. Os perfis metabólicos de LA associado a pré- PTD produziram modelos que, apesar do baixo poder de previsão, sugeriram alterações precoces no funcionamento da unidade fetoplacentária, hiperglicémia e stress oxidativo. Os modelos obtidos para os grupos pré- IUGR pré- PE, pré- PROM e pré-diagnóstico GDM (LA e urina materna) registaram baixo poder de previsão, indicando o pouco impacto destas condições na composição do LA e/ou urina do 2º trimestre. Os resultados obtidos demonstram as potencialidades da análise dos perfis metabólicos do LA (e, embora com base em menos estudos, da urina materna) do 2º trimestre para o desenvolvimento de novos e complementares métodos de diagnóstico, nomeadamente para FM e PTD.