Analysis and design of beam-shaped rectangular polyrod antennas

Theoretical and experimental investigations on the near field and radiation characteristics show a fairly good agreement which justifies the TE(11)(x) mode of excitation. Eight polyrod antennas of different configurations were built and tested as functions of taper angles, straight and curved axial lengths, and frequency of excitation. It is found that the radiation patterns. cross-polarization level, beamwidth and gain could be controlled not only by the axial length and taper angles but also by shaping the axis of the polyrods in order to realize an optimum design

Deuterium-carbon correlation in static oriented systems using DAPT - A windowless multiple pulse sequence

We present a new method for establishing correlation between deuterium and its attached carbon in a deuterated liquid crystal. The method is based on transfer of polarization using the DAPT pulse sequence proposed originally for two spin half nuclei, now extended to a spin-1 and a spin-1/2 nuclei. DAPT utilizes the evolution of magnetization of the spin pair under two blocks of phase shifted BLEW-12 pulses on one of the spins separated by a 90 degree pulse on the other spin. The method is easy to implement and does not need to satisfy matching conditions unlike the Hartmann-Hahn cross-polarization. Experimental results presented demonstrate the efficacy of the method.

Unraveling the packing pattern leading to gelation using SS NMR and X-ray diffraction: direct observation of the evolution of self-assembled fibers

A detailed understanding of the mode of packing patterns that leads to the gelation of low molecular mass gelators derived from bile acid esters was carried out using solid state NMR along with complementary techniques such as powder X-ray diffraction (PXRD), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and polarizing optical microscopy (POM). Solid state C-13{H-1} cross polarization (CP) magic angle spinning (MAS) NMR of the low molecularmass gel in its native state was recorded for the first time. A close resemblance in the packing patterns of the gel, xerogel and bulk solid states was revealed upon comparing their C-13{H-1} CPMAS NMR spectral pattern. A doublet resonance pattern of C-13 signals in C-13{H-1}CPMAS NMR spectra were observed for the gelator molecules, whereas the non-gelators showed simple singlet resonance or resulted inthe formation of inclusion complexes/solvates. PXRD patterns revealed a close isomorphous nature of the gelators indicating the similarity in the mode of the packing pattern in their solid state. Direct imaging of the evolution of nanofibers (sol-gel transition) was carried out using POM, which proved the presence of self-assembled fibrillar networks (SAFINs) in the gel. Finally powder X-ray structure determination revealed the presence of two non-equivalent molecules in an asymmetric unit which is responsible for the doublet resonance pattern in the solid state NMR spectra.

Circular dichroism and 13C nuclear magnetic resonance spectroscopy of pennisetin from pearl millet

The conformation and stability of pearl millet prolamin (pennisetin) were examined by using circular dichroism and C-13 nuclear magnetic resonance spectroscopy. The far UV spectrum of pennisetin in 70% (v/v) aqueous ethanol showed the presence of predominant alpha-helical structure and its occurrence in the alpha + beta class of protein. The far and near UV spectra of pennisetin in ethanol: trifluoroethanol also supported this observation. However pennisetin showed the presence of some helical structure in 8 M urea which is known to be a highly unordered structure forming solvent. A decrease in alpha helical content of native pennisetin was observed with rise in temperature from 5-75-degrees-C and this effect of temperature was found to be reversible. A C-13 NMR spectrum of pennisetin in 70% ethanol suggested a high degree of molecular mobility in ethanol. Comparison of the cross polarization spectrum with the single pulse excitation spectrum suggested pennisetin to be a heterogeneous protein.

Effect of Alkyl Chain Arrangement on Conformation and Dynamics in a Surfactant Intercalated Layered Double Hydroxide: Spectroscopic Measurements and MD Simulations

The anionic surfactant dodecyl sulfate (DDS) has been intercalated in an Mg-Al layered double hydroxide (LDH). Monolayer and bilayer arrangements of the alkyl chains of the intercalated surfactant can be engineered by tuning the Al/Mg ratio of the LDH. In both arrangements the anionic headgroup of the surfactant is tethered to the LDH sheets, and consequently translational mobility of the chains is absent. The degrees of freedom of the confined alkyl chains are restricted to changes in conformation. The effects of the arrangement of the intercalated surfactant chains on conformational order and dynamics have been,investigated by spectroscopic measurements and molecular dynamics simulations. Infrared, Raman, and C-13 NMR spectroscopies were used to investigate conformation of the alkyl chains in the monolayer and bilayer arrangements and variable contact time cross-polarization magic angle spinning (VCT CPMAS) NMR measurements to probe molecular motion. The alkyl chains in the monolayer arrangement of the intercalated DDS chains showed considerably greater conformational disorder and faster dynamics as compared to chains in the bilayer arrangement, in spite of the fact that the volume available per chain in the monolayer is smaller than that in the bilayer. Atomistic MD simulations of the two arrangements of the intercalated surfactant were carried out using an isothermal-isobaric ensemble. The simulations are able to reproduce the essential results of the experiment-greater conformational disorder and faster dynamics for the alkyl chains in the monolayer arrangement of the intercalated surfactant. The MD simulations show that these results are a consequence of the fact that the nature of conformational disorder in the two arrangements is different. In the monolayer arrangement the alkyl chains can sustain isolated gauche defects, whereas in the bilayer arrangement gauche conformers occur only as part of a kink a gauche(+) trans gauche(-) sequence.

Nematogens with more flexible chains than aromatic rings in the core

Mesogens containing four rings in the main core can accommodate one terminal and two nearby lateral chains on each outside aromatic ring. These compounds containing six chains present an enantiotropic nematic range which is influenced by the rigidity of the links. The conformational behaviour of the first methyleneoxy group within the chains was investigated by one and two dimensional C-13 NMR. The sign of the jump in chemical shifts when entering the nematic phase indicates the folding of each lateral branch. Dipolar oscillations during cross-polarization contact provide the values of the bond order parameter. The two First lateral fragments do not behave in the same way, demonstrating the influence of the fragment along which the chain is back: folded.

Study of liquid crystalline order by NMR

The liquid crystalline phase represents a unique state of matter where partial order exists on molecular and supra-molecular levels and is responsible for several interesting properties observed in this phase. Hence a detailed study of ordering in liquid crystals is of significant scientific and technological interest. NMR provides several parameters that can be used to obtain information about the liquid crystalline phase. Of these, the measurement of dipolar couplings between nuclei has proved to be a convenient way of obtaining liquid crystalline ordering since the coupling is dependent on the average orientation of the dipolar vector in the magnetic field which also aligns the liquid crystal.However, measurement of the dipolar coupling between a pair of selected nuclei is beset with problems that require special solutions. In this article the use of cross polarization for measuring dipolar couplings in liquid crystals is illustrated. Transient oscillations observed during cross polarization provide the dipolar couplings between essentially isolated nearest neighbor spins which can be extracted for several sites simultaneously by employing two-dimensional NMR techniques. The use of the method for obtaining heteronuclear dipolar couplings and hence the order parameters of liquid crystals is presented. Several modifications to the basic experiment are considered and their utility illustrated. A method for obtaining proton–proton dipolar couplings, by utilizing cross polarization from the dipolar reservoir, is presented. Some applications are also highlighted.

Constructing Thin Polythiophene Film Composed of Aligned Lamellae via Controlled Solvent Vapor Treatment

Thin poly(3-butylthiophene) (P3BT) film composed of aligned lamellae attached to the edge of the original film has been achieved via a controlled solvent vapor treatment (C-SVT) method. The polarized optical microscopy operated at both single-polarization and cross-polarization modes has been used to investigate the alignment of the fiber-like lamellae. A numerical simulation method is used to quantitatively calculate angle distributions of the lamellae deviated from the film growth direction. Prepatterned P3BT film edge acts as nuclei which densely initialize subsequent crystal growth by exhausting the materials transported from the partially dissolved film. The growth of new film upon crystallization is actually a self-healing process where the two-dimensional geometric confinement is mainly responsible for this parallel alignment of P3BT crystals. The solvent vapor pressure should be carefully chosen so as to induce crystal growth but avoid liquid instability which will destroy the continuity of the film.

A HIGH-RESOLUTION SOLID-STATE NMR AND DSC STUDY OF MISCIBILITY AND CRYSTALLIZATION BEHAVIOR OF POLY(VINYL ALCOHOL)/POLY(N-VINYL-2-PYRROLIDONE) BLENDS

Blends of crystallizable poly(vinyl alcohol) (PVA) with poly(N-vinyl-2-pyrrolidone) (PVPy) were studied by C-13 cross-polarization/magic angle spinning (CP/MAS) n.m.r. and d.s.c. The C-13 CP/MAS spectra show that the blends were miscible on a molecular level over the whole composition range studied, and that the intramolecular hydrogen bonds of PVA were broken and intermolecular hydrogen bonds between PVA and PVPy formed when the two polymers were mixed. The results of a spin-lattice relaxation study indicate that blending of the two polymers reduced the average intermolecular distance and molecular motion of each component, even in the miscible amorphous phase, and that addition of PVPy into PVA has a definite effect on the crystallinity of PVA in the blends over the whole composition range, yet there is still detectable crystallinity even when the PVPy content is as high as 80 wt%. These results are consistent with those obtained from d.s.c. studies.

Validation of RADARSAT-2 fully polarimetric SAR measurements of ocean surface waves

C band RADARSAT-2 fully polarimetric (fine quad-polarization mode, HH+VV+HV+VH) synthetic aperture radar (SAR) images are used to validate ocean surface waves measurements using the polarimetric SAR wave retrieval algorithm, without estimating the complex hydrodynamic modulation transfer function, even under large radar incidence angles. The linearly polarized radar backscatter cross sections (RBCS) are first calculated with the copolarization (HH, VV) and cross-polarization (HV, VH) RBCS and the polarization orientation angle. Subsequently, in the azimuth direction, the vertically and linearly polarized RBCS are used to measure the wave slopes. In the range direction, we combine horizontally and vertically polarized RBCS to estimate wave slopes. Taken together, wave slope spectra can be derived using estimated wave slopes in azimuth and range directions. Wave parameters extracted from the resultant wave slope spectra are validated with colocated National Data Buoy Center (NDBC) buoy measurements (wave periods, wavelengths, wave directions, and significant wave heights) and are shown to be in good agreement.

The stability of nanosized HZSM-5 zeolite: a high-resolution solid-state NMR study

The thermal and hydrothermal stabilities of HZSM-5 zeolites with crystal sizes less than 100 nm have been studied by multinuclear solid-state NMR, combined with BET and XRD. As evidenced by Al-27 and Si-29 MAS as well as their corresponding cross-polarization/MAS NMR investigations, the thermal stability of nanosized HZSM-5 is not so good as that of microsized HZSM-5. This is due to two processes concerning dealumination and desilicification involved in the calcination of nanosized HZSM-5, while only the dealumination process is conducted in microsized HZSM-5 under the similar calcination process. The hydrothermal stability of nanosized HZSM-5 is, contrary to what was expected, not so bad as that of the microsized HZSM-5 in the course of steam treatment. The actual resistance of the hydrothermal stability to the crystal size of HZSM-5 can be ascribed to an active reconstruction of zeolitic framework through an effective filling of amorphous Si species into nanosized HZSM-5 during hydrothermal treatment. (C) 2001 Published by Elsevier Science B.V.

Transmission characteristics of a vaginally-worn UHF radio telemeter

A vaginally-worn temperature telemeter may be used by women to chart their basal body temperature for ovulation detection. The telemeter uses a temperature to pulse width converter to key a Colpitts oscillator which is controlled in frequency by a 418 MHz SAW resonator. The circuit’s tank inductor acts as a compact, multi-turn loop antenna with a radiated power in isolation of around 1 uW. The transmission characteristics of the system are affected by the proximity of the human body, which acts as an electrically-large lossy dielectric. The RF link-budget must allow for the reduction in total emitted power, directional body-induced fading, and polarization effects. The polar power patterns of the telemeter were measured for both isolated and in-situ cases, using horizontal and vertical polarization. The power patterns were numerically integrated to determine relative emitted power, and a reference dipole used to determine the emitted power for the isolated device. In isolation the telemeter radiation is vertically polarized and isotropic in nature. With the telemeter in-situ, total body absorption was found to be over 20 dB, with directional fades of up to 40 dB; there was extensive cross-polarization, with up to 60% of radiated power horizontally polarized. With limited radiated power and directional fading, the operating range for the telemeter is limited to single room operation (less than 10m). The majority of RF radiation is absorbed by the body, but the radiation hazard is negligible due to the low power level of the device. The high level of cross-polarization suggests that either horizontal or vertically polarized base-station antennas may be used.

Preparation of new materials by heterogeneous modification of cellulose

O presente trabalho teve como principal objectivo estudar a modificação química heterogénea controlada de fibras de celulose com diferentes reagentes de modo a alterar as suas propriedades de superfície, em especial em termos da criação de um carácter hidrofóbico e lipofóbico, preservando, sempre que possível, as suas propriedades mecânicas e, consequentemente, abrindo novas perspectivas de aplicação. O desenvolvimento do trabalho envolveu três abordagens principais, envolvendo, em cada caso, o estudo de diferentes condições reaccionais. Na primeira abordagem foram utilizados como reagentes de modificação compostos perfluorados, nomeadamente o anidrido trifluoroacético (TFAA), o cloreto de 2,3,4,5,6-pentafluorobenzoílo (PFBz) e o cloreto de 3,3,3- trifluoropropanoílo (TFP), para promover a acilação heterogénea da superfície das fibras. A segunda estratégia usada consistiu na preparação de híbridos de celulose do tipo orgânico-inorgânico classe-II, através da modificação das fibras de celulose com o (3-isocianatopropil)trietoxissilano (ICPTEOS), um reagente organossilano bifuncional. A ligação às fibras de celulose foi efectuada através das funções isocianato e, posteriormente, os grupos etoxissilano foram sujeitos a tratamentos de hidrólise ácida, como tal ou na presença de outros siloxanos, nomeadamente o tetraetoxissilano (TEOS) e o 1H,1H,2H,2Hperfluorodeciltrietoxissilano (PFDTEOS). Finalmente, a última abordagem foi baseada na modificação das fibras com triclorometilssilano (TCMS), através de uma reacção gás-sólido, que dispensou assim o uso de solventes orgânicos. A ocorrência de modificação química foi em cada caso confirmada por Espectroscopia de Infravermelho com Transformada de Fourier e Reflectância Total Atenuada (FTIR-ATR), Análise Elementar (EA) e determinação de ângulos de contacto. Adicionalmente, e dependendo de cada caso específico, diversas outras técnicas foram empregues na caracterização aprofundada dos materiais preparados, nomeadamente Ressonância Magnética Nuclear CPMAS no Estado Sólido (RMN), Espectroscopia de Difracção de Raios-X (XRD), Análise Termogravimétrica (TGA), Espectrometria de Massa de Iões Secundários com Análise de Tempo de Vôo (ToF-SIMS), Espectroscopia Fotoelectrónica de Raios-X (XPS) e Microscopia Electrónica de Varrimento (SEM). Relativamente à acilação das fibras de celulose com reagentes perfluorados, o sucesso da reacção foi comprovado por FTIR-ATR, EA, XPS e ToF-SIMS. Neste contexto, obtiveram-se fibras modificadas possuindo graus de substituição (DS) compreendidos entre 0.006 e 0.39. Verificou-se por XRD que, em geral, mesmo para os valores de DS mais elevados, a cristalinidade das fibras não foi afectada, indicando que a modificação foi limitada às camadas mais superficiais das mesmas ou a regiões amorfas das suas camadas mais internas. Adicionalmente, observou-se por ToF-SIMS que a distribuição dos grupos perfluorados à superfície das fibras foi, de facto, bastante heterogénea. Todos os derivados de celulose perfluorados apresentaram elevada hidrofobicidade e lipofobicidade, tendo-se atingido ângulos de contacto com água e diiodometano de 126º e 104º, respectivamente. Um aspecto interessante relativo a estes materiais é que a elevada omnifobicidade foi observada mesmo para valores de DS muito reduzidos, não se mostrando significativamente afectada pelo aumento dos mesmos. Em consonância, verificou-se por XPS que a cobertura da superfície das fibras de celulose com grupos perfluorados aumentou apenas ligeiramente com o aumento do DS, apontando para a esterificação de camadas mais internas das fibras, associada, neste caso, predominantemente aos seus domínios amorfos. No que diz respeito à estabilidade hidrolítica destes derivados, obtiveram-se dois tipos distintos de comportamento. Por um lado, as fibras de celulose trifluoroacetiladas são facilmente hidrolisáveis em meio neutro, e, por outro, as fibras pentafluorobenzoiladas e trifluoropropanoiladas mostram-se bastante resistentes face a condições de hidrólise em meio neutro e ácido (pH 4), podendo, contudo, ser facilmente hidrolisadas em meio alcalino (pH 9 e 12, para derivados do PFBz e do TFP, respectivamente). Na segunda abordagem verificou-se a ocorrência de reacção por FTIR-ATR e EA. Em geral, a modificação química com ICPTEOS ocorre predominantemente nas zonas mais superficiais das fibras de celulose ou em regiões amorfas. Contudo, em condições reaccionais mais severas (maior quantidade de reagente e tempo de reacção), esta atingiu também regiões cristalinas, afectando, consequentemente, a estrutura cristalina das fibras, como verificado por XRD. Por RMN de 29Si observou-se que após reacção com o ICPTEOS já existiam indícios de alguma hidrólise dos grupos etoxissilano, e que a sua subsequente condensação parcial tinha levado à formação de uma película inorgânica em redor das fibras (verificado por SEM), constituída maioritariamente por estruturas lineares, com uma contribuição mais modesta de estruturas “diméricas” e outras mais ramificadas. Consequentemente, este revestimento inorgânico transformou as fibras de celulose em materiais híbridos com elevada hidrofobicidade (ângulos de contacto com água entre 103-129º). A hidrólise ácida dos restantes grupos etoxissilano, como tal ou na presença de TEOS, originou híbridos de celulose com elevada hidrofilicidade, sendo impossível medirem-se os ângulos de contacto com água dos produtos finais, devido à presença maioritária de grupos silanol (Si-OH) e ligações Si-O-Si à superfície, os quais contribuíram para o consequente aumento de energia de superfície. No entanto, quando a hidrólise foi realizada na presença de PFDTEOS, obtiveram-se materiais híbridos com elevada hidrofobicidade e lipofobicidade (ângulos de contacto com água e diiodometano de 140º e 134º, respectivamente), devido à combinação da presença de grupos perfluorados e micro- e nano-rugosidades na superfície das fibras de celulose, conforme confirmado por SEM. Finalmente, a última abordagem permitiu preparar materiais derivados de celulose altamente hidrofóbicos e lipofóbicos (ângulos de contacto com água e diiodometano de 136º e 109º, respectivamente) por um processo simples, envolvendo tempos de tratamento tão curtos como 0.5 min. Este comportamento omnifóbico foi gerado pelo efeito sinergético entre a diminuição de energia de superfície das fibras, devido à presença de grupos metilo dos resíduos de TCMS ligados a estas, e a condensação dos resíduos de TCMS na forma de micro- e nano-partículas inorgânicas, que levou à criação de um revestimento rugoso à superfície das fibras, conforme observado por RMN de 29Si e SEM, respectivamente. A pré-humidificação das fibras de celulose demonstrou desempenhar um importante papel de “acelerador” dos processos de hidrólise e condensação das moléculas de TCMS. Nestas condições, o tempo de tratamento foi um dos parâmetros mais relevantes, pois para tempos de tratamento muito curtos (0.5 min) os materiais resultantes não apresentaram quaisquer diferenças a nível de propriedades físico-químicas em relação ao substrato de partida (a humidade em excesso consumiu todo o TCMS antes que este conseguisse reagir com os grupos hidroxilo das fibras de celulose), possuindo, por exemplo, valores de ângulos de contacto com água idênticos. Para tempos de tratamento mais longos, como 30 min, os materiais finais apresentaram a maior quantidade de componentes inorgânicos, tal como verificado por EA e TGA. Assim, o controlo da humidade das fibras é imperativo para se poder moldar as propriedades finais dos produtos. Esta última abordagem é particularmente promissora uma vez que tem como base um sistema simples e “verde” que pode ser facilmente implementado. Em conclusão, este trabalho permitiu demonstrar que a modificação química heterogénea controlada das fibras de celulose representa uma iniciativa promissora para a preparação de novos materiais obtidos a partir de recursos renováveis, com propriedades interessantes e passíveis de ser potencialmente aplicados em diferentes áreas. Para além do mais, as estratégias de modificação estudadas podem também ser precursoras de novos estudos que possam vir a ser desenvolvidos dentro do mesmo âmbito.

Characterization of water-soluble organic matter from urban aerosols

Water-soluble organic matter (WSOM) from atmospheric particles comprises a complex array of molecular structures that play an important role on the physic-chemical properties of atmospheric particles and, therefore, are linked to several global-relevant atmospheric processes which impact the climate and public health. Due to the large variety of sources and formation processes, adequate knowledge on WSOM composition and its effects on the properties of atmospheric aerosol are still limited. Therefore, this thesis aims at providing new insights on the molecular composition of WSOM from fine atmospheric aerosols typical of an urban area (Aveiro, Portugal). In a first step, adsorption phenomena of semivolatile organic compounds on quartz fibre filters employed in the collection of atmospheric aerosols were assessed. Afterwards, atmospheric aerosol samples were collected during fifteen months, on a weekly basis. A mass balance of aerosol samples was performed in order to set the relative contribution of elemental carbon, WSOM and water-insoluble organic matter to the aerosol mass collected at the urban area of Aveiro, with a special focus on the assessment of the influence of different meteorological conditions. In order to assess the chemical complexity of the WSOM from urban aerosols, their structural characteristics were studied by means of Fourier transform infrared infrared - Attenuated Total Reflectance (FTIR-ATR) and solid-state cross polarization with magic angle spinning 13C nuclear magnetic resonance (CPMAS 13C NMR) spectroscopies, as well as their elemental composition. The structural characterization of aerosol WSOM samples collected in the urban area highlighted a highly complex mixture of functional groups. It was concluded that aliphatic and aromatic structures, hydroxyl groups and carboxyl groups are characteristic to all samples. The semi-quantitative assessment of the CPMAS 13C NMR data showed different distributions of the various functional groups between the aerosol samples collected at different seasons. Moreover, the presence of signals typical of lignin-derived structures in both CPMAS 13C NMR and FTIR-ATR spectra of the WSOM samples from the colder seasons, highlights the major contribution of biomass burning processes in domestic fireplaces, during low temperature conditions, into the bulk chemical properties of WSOM from urban aerosols. A comprehensive two-dimensional liquid chromatography (LC x LC) method, on-line coupled to a diode array, fluorescence, and evaporative light scattering detectors, was employed for resolving the chemical heterogeneity of the aerosol WSOM samples and, simultaneously, to map the hydrophobicity versus the molecular weight distribution of the samples. The LC x LC method employed a mixed-mode hydrophilic interaction column operating under aqueous reversed phase mode in the first dimension, and a size-exclusion column in the second dimension, which was found to be useful for separating the aerosol WSOM samples into various fractions with distinct molecular weight and hydrophobic features. The estimative of the average molecular weight (Mw) distribution of the urban aerosol WSOM samples ranged from 48 to 942 Da and from 45 to 1241 Da in terms of UV absorption and fluorescence detection, respectively. Findings suggest that smaller Mw group fractions seem to be related to a more hydrophobic nature.

Polarimetry In Radar Backscattering from Soil and Vegetated Surfaces

Thesis (Ph.D.)--University of Washington, 2015