Microwave generation in an electro-absorption modulator integrated with a DFB laser subject to optical injection

This paper presents a new technique to generate microwave signal using an electro-absorption modulator (EAM) integrated with a distributed feedback (DFB) laser subject to optical injection. Experiments show that the frequency of the generated microwave can be tuned by changing the wavelength of the external laser or adjusting the bias voltage of the EAM. The frequency response of the EAM is studied and found to be unsmooth due to packaging parasitic effects and four-wave mixing effect occurring in the active layer of the DFB laser. It is also demonstrated that an EA modulator integrated in between two DFB lasers can be used instead of the EML under optical injection. This integrated chip can be used to realize a monolithically integrated tunable microwave source. (C) 2009 Optical Society of America

Electrical and optical coupling in an electroabsorption modulator integrated with a DFB laser

Electrical and optical coupling in an electroabsorption (EA) modulator integrated with a distributed feedback (DFB) laser have been investigated. The integrated device is treated as a three-port optoelectronic device with two electrical ports and one optical output port. The scattering parameters of this three-port device have been measured in the designed experiment. The measured results indicate that there exists the electrical coupling between the DFB laser and EA modulator of the integrated light source whenever the current applied to the laser section is below or above the threshold current, and the optical coupling will have stronger influence on the frequency responses than the electrical coupling when the bias current is above the threshold. A small-signal equivalent circuit model for the integrated device is established considering both the electrical and internal optical coupling. Experiments show that the equivalent circuit model is reasonable and the determined element values are correct. Based on the measurement and modeling, the influences of the electrical and optical coupling on the high-frequency responses are investigated and the effective measure to eliminate the additional modulation in the DFB laser are discussed.

High-power electroabsorption modulator for radio over fibre system

An electroabsorption modulator using an intra-step quantum well (IQW) active region is fabricated for a radio over fibre system. The strain-compensated InGaAsP/InGaAsP IQW shows good material quality and improved modulation properties, high extinction ratio efficiency (10 dB V-1) and low capacitance (< 0.42 pF), with which high frequency (> 15 GHz) can be obtained. High-speed measurement under high-power excitation shows no power saturation up to an excitation power of 21 dBm. To our knowledge, the input optical power is the highest reported for a multi-quantum well EAM without a heat sink.

Design and fabrication of 1.06 mu m resonant-cavity enhanced reflective modulator with GaInAs/GaAs quantum wells

A resonant-cavity enhanced reflective optical modulator is designed and frabricated, with three groups of three highly strained InGaAS/GaAs quantum wells in the cavity, for the low voltage and high contrast ratio operation. The quantum wells are positioned in antinodes of the optical standing wave. The modulator is grown in a single growth step in an molecular beam epitaxy system, using GaAs/AIAs distributed Bragg reflectors as both the top and bottom mirrors. Results show that the reflection device has a modulation extinction of 3 dB at -4.5 V bias.

1.55-mu m Ridge DFB laser and electroabsorption modulator integrated with buried-ridge-stripe dual-waveguide spot-size converter output

A 1.55-mu m ridge distributed feedback laser and electroabsorption modulator monolithically integrated with a buried-ridge-stripe dual-waveguide spot-size converter (SSC) at the output port for low-loss coupling to a cleaved single-mode optical fiber was fabricated by means of selective area growth, quantum-well intermixing, and dual-core technologies. These devices exhibit threshold current of 28 mA, 3-dB modulation bandwidth of 12.0 GHz, modulator extinction ratios of 25.0-dB dc. The output beam divergence angles of the SSC in the horizontal and vertical directions are as small as 8.0 degrees x 12.6 degrees, respectively, resulting in 3.2-dB coupling loss with a cleaved single-mode optical fiber.

An investigation on fiber coupled polymer waveguide for electro-optic modulator

A novel crosslinkable polyurethane is used as the core layer of the electro-optic(E-O) modulator. The refractive index and dispersion of this material have been detected by analyzing the F-P oscillation in transmission spectra. Calculated results from the effective index method are given to design the Mach-Zehnder and straight 5-layer ridge wave-guide device (including the metal electrodes). With light at 1.31 mum being fiber coupled into waveguide, the mode properties of these devices have been demonstrated in a micron control system. The guided mode is accordant with the theoretical analysis.

Heat shock protein 70-mediated sensitization of cells to apoptosis by Carboxyl-Terminal Modulator Protein

Background: The serine/threonine protein kinase B (PKB/Akt) is involved in insulin signaling, cellular survival, and transformation. Carboxyl-terminal modulator protein (CTMP) has been identified as a novel PKB binding partner in a yeast two-hybrid screen, and appears to be a negative PKB regulator with tumor suppressor-like properties. In the present study we investigate novel mechanisms by which CTMP plays a role in apoptosis process.

MIC-1 (a multifunctional modulator of dendritic cell phenotype and function) is produced by decidual stromal cells and trophoblasts

Macrophage inhibitory cytokine-1 (MIC-1) is a multifunctional cytokine produced in high amounts by placental tissue. Inhibiting trophoblast invasion and suppressing inflammation through inhibition of macrophage activation, MIC-1 is thought to provide pleiotropic functions in the establishment and maintenance of pregnancy. So far, little is known about the decidual cell subsets producing MIC-1 and the effect of this cytokine on dendritic cells (DCs), which are known to play a distinct role in the development of pro-fetal tolerance in pregnancy.

Effects of SB-205384, a positive modulator of (alfa)3-subunit-containing GABA-A receptors, on isolation-induced aggressions in male mice. 'Efectos del SB-205384, un modulador positivo de los receptores GABA-A que contienen la subunidad (alfa)3, sobre la agresi??n inducida por aislamiento en ratones machos'

Resumen tomado de la publicaci??n

Calidad de vida laboral y liderazgo en trabajadores asistenciales y administrativos en un centro oncológico de la ciudad de Bogotá

El propósito de este estudio fue describir la Calidad de vida laboral (CVL) y el estilo de liderazgo percibido por el personal administrativo/asistencial de un centro oncológico y estimar la asociación entre ellas, considerando las características sociodemográficas. Para ello se aplicó el Cuestionario de Vida profesional [CVP-35] y el Test de Adjetivos de Pitcher [PAT]. En general, los participantes presentan una CVL satisfactoria, caracterizada principalmente por motivación intrínseca, lo cual fue más evidente en el personal asistencial. Respecto al liderazgo, se observó una percepción de ausencia de liderazgo o características poco deseables de éste, lo cual aunque no determina la CVL, si constituye un factor modulador de la misma, las variables sociodemográficas no guardaron relación con la CVL. Por último se resalta la responsabilidad social que tienen los directivos sobre bienestar de los trabajadores de la salud, y consecuentemente sobre la atención al paciente. Se discuten estos hallazgos y lo pertinente de utilizar las categorías emergentes del PAT.

Cis-4-methylsphingosine is a sphingosine-1-phosphate receptor modulator

Sphingosine-1-phosphate (S1P) acts as high affinity agonist at specific G-protein-coupled receptors, S1P(1-5), that play important roles e.g. in the cardiovascular and immune systems. A S1P receptor modulating drug, FTY720 (fingolimod), has been effective in phase III clinical trials for multiple sclerosis. FTY720 is a sphingosine analogue and prodrug of FTY720-phosphate, which activates all S1P receptors except S1P(2) and disrupts lymphocyte trafficking by internalizing the S1P(1) receptor. Cis-4-methylsphingosine (cis-4M-Sph) is another synthetic sphingosine analogue that is readily taken up by cells and phosphorylated to cis-4-methylsphingosine-1-phosphate (cis-4M-S1P). Therefore, we analysed whether cis-4M-Sph interacted with S1P receptors through its metabolite cis-4M-S1P in a manner similar to FTY720. Indeed, cis-4M-Sph caused an internalization of S1P receptors, but differed from FTY720 as it acted on S1P(2) and S1P(3) and only weakly on S1P(1), while FTY720 internalized S1P(1) and S1P(3) but not S1P(2). Consequently, pre-incubation with cis-4M-Sph specifically desensitized S1P-induced [Ca(2+)](i) increases, which are mediated by S1P(2) and S1P(3), in a time- and concentration-dependent manner. This effect was not shared by sphingosine or FTY720, indicating that metabolic stability and targeting of S1P(2) receptors were important. The desensitization of S1P-induced [Ca(2+)](i) increases was dependent on the expression of SphKs, predominantly of SphK2, and thus mediated by cis-4M-S1P. In agreement, cis-4M-S1P was detected in the supernatants of cells exposed to cis-4M-Sph. It is concluded that cis-4M-Sph, through its metabolite cis-4M-S1P, acts as a S1P receptor modulator and causes S1P receptor internalization and desensitization. The data furthermore help to define requirements for sphingosine kinase substrates as S1P receptor modulating prodrugs.

Estructura y pruebas con Labmu

La implantación de la televisión digital en España ha supuesto un conjunto de desafíos técnicos y de orden práctico que se han ido acometiendo en multitud de ámbitos, desde la legislación que normaliza las infraestructuras comunes de telecomunicación hasta los cambios en las instalaciones y receptores donde el usuario final recibe los servicios. Por la complejidad y el carácter interdisciplinar de los conocimientos necesarios el aprendizaje de los titulados dentro del ámbito de la Telecomunicación supone también un reto importante. Este proyecto realiza una primera aproximación a un conjunto de herramientas hardware y software de ayuda a la enseñanza de esta amplia disciplina. El proyecto se ha realizado en torno a Labmu laboratorio multiusuario para prácticas de televisión digital de la empresa Xpertia. Se ha realizado para conocer y documentar sus posibilidades. También se ha documentado la tarjeta moduladora DTA-111 y el software para Windows StreamXpress. Estos sistemas ofrecen muchas posibilidades para la docencia de la televisión digital en todas las áreas desde la codificación fuente hasta la decodificación en el usuario final. En particular para ambos sistemas se han realizado pruebas en radiofrecuencia de emisiones de TDT. También se han establecido algunas ideas para trabajo futuro con estos sistemas. El proyecto se divide en seis capítulos: Capitulo 1: En el primer capítulo titulado Introducción se presenta el proyecto. Capítulo 2: En el segundo capítulo titulado Composición Hardware Labmu se presentan todos los componentes del laboratorio Labmu con la descripción de cada componente y sus características técnicas. Así mismo se presenta el interconexionado y configuración con que se ha trabajado. Capítulo 3: En el tercer capítulo titulado Software Labmu se describe como manual de usuario todos los componentes y posibilidades de software de Labmu. Capítulo 4: En el cuarto capítulo titulado Medidas con Labmu se realiza las medidas de MER, CBER, VBER, C/N y potencia de canal de los canales emitidos en la Comunidad de Madrid, comparando estas medidas con el analizador Promax Prodig-5. Capítulo 5: En el quinto capítulo titulado Tarjeta receptora y software se describe la tarjeta DTA-111 y el software StreamXpress, realizando medidas con el analizador Promax Prodig-5 introduciendo errores a la señal emitida por la tarjeta, y estudiando los niveles límites de visualización correcta. Capítulo 6: En el sexto y último capítulo titulado Conclusiones se presentan las conclusiones del proyecto y un plan de trabajo futuro ABSTRACT. The implantation of Digital Television in Spain (TDT) has implied a number of technical and practical challenges in several scopes. These challenges range from recommendations that standardize common telecommunications infrastructure to the changes in facilities where the end user receives digital services. The complexity and the interdisciplinary nature of skills that graduate Telecommunications students need to learn, is also a major challenge. This project is a first approach of a set of hard ware and software tools to help in the task of teaching this broad range discipline. The project has been carried out on Labmu, a multiuser Digital Television laboratory created by the Xpertia company. Its objectives are to understand and document this range of possibilities. DTA-111 modulator card and software for Windows StreamXpress have also been documented. These systems offer many options for teaching digital television in all areas, from source coding to end user decoding. In particular, both systems were tested on RF emissions in TDT. More over some ideas for future work with these systems have also foreseen. The project is structured in six chapters: Chapter1: This section Introduces the project. Chapter2: Titled “The Composition Hardware Labmu” presents Labmu lab components and provides descriptions for each component and its technical characteristics. It also presents the interconnection and configuration we have been using. Chapter3: Titled “Software Labmu” is a user manual, describing all components and software possibilities Labmu offers. Chapter4: Titled “Measures to Labmu” presents MER, CBER, VBER, C /N and channel power measures provided by Labmu in comparison with Promax Prodig-5 measures for all channels broad casting digital television services in the Community of Madrid. Chapter 5 Titled “Receiver card and software” describes DTA-111 card and software StreamXpress. Also the effects of errors insertion performed by this card are measured with the PromaxProdig-5 meter. Threes hold levels for correct reception are also studied. Chapter6: Entitled Conclusions presents the conclusions of the project and a plan for future work.

Compatibilidad de Orius laevigatus (Fieber) (Hemiptera: Anthocoridae) y Nesidiocoris tenuis (Reuter)(Hemiptera: Miridae), depredadores importantes en cultivos hortícolas protegidos, con nuevas barreras físicas selectivas y modernos plaguicidas

La nueva legislación en materia fitosanitaria se dirige hacia una Gestión Integrada de Plagas (GIP). Estos programas dan preferencia a aquellos métodos más respetuosos y sostenibles con el medio ambiente, siendo piezas claves en ellos el control biológico, el físico y otros de carácter no químico. Sin embargo, el uso de insecticidas selectivos es a veces necesario para el adecuado manejo de plagas en cultivos hortícolas. Por ello, el objetivo general de este estudio es aportar conocimientos para mejorar el control de plagas en cultivos hortícolas, mediante la integración de tres estrategias de lucha: biológica, física y química. Una parte de este trabajo ha consistido en el estudio de los posibles efectos que mallas tratadas con insecticida (bifentrin) pudieran provocar mediante diferentes ensayos de laboratorio, invernadero y campo, en los enemigos naturales Orius laevigatus (Fieber) (Hemiptera: Anthocoridae) (depredador de trips), Nesidiocoris tenuis (Reuter) (Hemiptera: Miridae) (depredador de mosca blanca y Tuta absoluta (Meirick) (Lepidoptera: Gelechiidae)), y otros agentes de biocontrol comúnmente usados en cultivos hortícolas protegidos. Este tipo de mallas se han empleado con éxito en entomología médica para controlar mosquitos vectores de la malaria, y actualmente se está trabajando en su desarrollo para uso agrícola como método de exclusión, y método directo de control de plagas. En los ensayos realizados en laboratorio, O. laevigatus y N. tenuis no fueron capaces de detectar la presencia de bifentrin en el ensayo de preferencia. Además, no se produjo mortalidad a corto plazo (72 horas) en ambos chinches depredadores. Por el contrario, se registró una elevada mortalidad cuando se expusieron por contacto a la malla tratada durante 72 horas en cajas de dimensiones reducidas (10 cm de diámetro X 3 cm de altura). En ensayos llevados a cabo bajo condiciones más reales de exposición, en un invernadero experimental con jaulas de 25 X 25 X 60 cm de altura, no se produjo ningún efecto en la mortalidad a corto plazo (72 horas) o en los parámetros reproductivos de O. laevigatus y N. tenuis. Finalmente, en ensayos de campo realizados en túneles semi-comerciales (8 m de largo X 6,5 m de ancho X 2,6 m de altura), ni las condiciones ambientales [temperatura, humedad relativa, radiación ultravioleta (UV) y fotosintéticamente activa (PAR)], ni los enemigos naturales, se vieron afectados por la presencia de la malla tratada con bifentrin en el cultivo. Sin embargo, los resultados no fueron concluyentes, debido al bajo establecimiento de los agentes de biocontrol liberados. Por lo tanto, más estudios son necesarios en invernaderos comerciales para confirmar los resultados preliminares de compatibilidad. Además, en este trabajo se han evaluado los efectos letales (mortalidad) y subletales (parámetros reproductivos) de seis modernos insecticidas sobre los chinches depredadores O. laevigatus y N. tenuis, mediante ensayos de laboratorio y persistencia. Los ensayos se realizaron por contacto residual, aplicando los insecticidas a la dosis máxima de campo sobre placas de cristal (laboratorio) o plantas (persistencia). Los productos fitosanitarios se seleccionaron por representar a un grupo de modernos plaguicidas con modos de acción en principio más selectivos para los enemigos naturales que antiguos plaguicidas como organoclorados, oroganofosforados o carbamatos, y por su uso frecuente en cultivos hortícolas donde O. laevigatus y N. tenuis están presentes. Todos ellos están incluidos o en proceso de inclusión en la lista comunitaria de sustancias activas para uso agrícola, Anexo I de la Directiva 91/414/CEE: abamectina y emamectina (avermectinas neurotóxicas, activadoras del canal del cloro), deltametrina (piretroide neurotóxico, modulador del canal del sodio, control positivo), flubendiamida (neurotóxico, modulador del receptor de rianodina), spinosad (naturalito neurotóxico, agonistas/antagonistas del receptor de nicotínico acetilcolina) y spiromesifen (inhibidor de la acetil CoA carboxilasa). El estudio mostró que O. laevigatus fue más susceptible a los insecticidas que N. tenuis. Además, los resultados revelaron que flubendiamida y spiromesifen fueron compatibles con los dos enemigos naturales estudiados, y por tanto se podrían usar en programas de GIP. Por el contrario, los insecticidas abamectina, deltametrina, emamectina y spinosad no fueron selectivos para ninguno de los chinches depredadores. Sin embargo, los estudios de persistencia demostraron que a pesar de que estos insecticidas no proporcionaron selectividad fisiológica, pueden proporcionar selectividad ecológica en algunos casos. Abamectina, deltametrina, emamectina y spinosad podrían ser compatibles con N. tenuis si el enemigo natural es introducido en el cultivo 4 días después de su aplicación. En el caso de O. laevigatus, abamectina, deltametrina y spinosad se clasificaron como persistentes, por lo tanto es necesario completar el estudio con experimentos de semi-campo y campo que determinen si es posible su uso conjunto en programas de GIP. Por otro lado, emamectina podría ser compatible con O. laevigatus si el enemigo natural es introducido en el cultivo 7 días después de su aplicación. Por último, se ha comprobado la selectividad de tres insecticidas aceleradores de la muda (MACs) (metoxifenocida, tebufenocida y RH-5849) sobre O. laevigatus y N. tenuis. Además de realizar estudios para evaluar la toxicidad en laboratorio de los insecticidas por contacto residual e ingestión (principal modo de acción de los MAC´s), se extrajo RNA de los insectos y con el cDNA obtenido se secuenció y clonó el dominio de unión al ligando (LBD) del receptor de ecdisona correspondiente a O. laevigatus (OlEcR-LBD) y N. tenuis (NtEcR-LBD). Posteriormente, se obtuvo la configuración en tres dimensiones del LBD y se estudió el acoplamiento de las moléculas de los tres insecticidas en la cavidad que forman las 12 α-hélices que constituyen el EcR-LBD. En el caso de N. tenuis se debe mencionar que no fue posible la obtención de la secuencia completa del LBD. Sin embargo, se obtuvo una secuencia parcial (hélice 6-hélice 11), que mostró una alta conservación de aminoácidos con respecto a la obtenida en O. laevigatus. Los ensayos de toxicidad mostraron que metoxifenocida, tebufenocida y RH-5849 no produjeron ningún efecto nocivo en ambos depredadores. Además, los estudios de modelado por homología y acoplamiento molecular llevados a cabo con O. laevigatus, también indicaron que los MACs no produjeron ningún efecto deletéreo en este enemigo natural. Por lo tanto, estos compuestos pueden ser aplicados de manera segura en programas de GIP en los cuales O. laevigatus y N. tenuis estén presentes. ABSTRACT The new pesticide legislation on pest control is aimed at integrated pest management (IPM). These programs are based on the most environmentally sustainable approaches, where biological, physical control and other non-chemical methods are the cornerstone. However, selective pesticides are often required for pest management on horticultural crops. Therefore, the main goal of this study is to provide knowledge to improve pest control on horticultural crops through the integration of three strategies: biological, physical and chemical. Firstly, the effects of insecticide treated nets (bifenthrin) were evaluated in different laboratory, greenhouse and field experiments on the natural enemies Orius laevigatus (Fieber) (Hemiptera: Anthocoridae) (predator of thrips), Nesidiocoris tenuis (Reuter) (Hemiptera: Miridae) (predator of whiteflies and Tuta absoluta (Meirick) (Lepidoptera: Gelechiidae)), and other biocontrol agents commonly used on protected horticultural crops. These types of nets have been successfully used in medical entomology to control mosquito malaria vectors, and work is currently being done on their use as exclusion barriers and as a direct method of pest control in agriculture. In experiments made under laboratory conditions, O. laevigatus and N. tenuis were not able to detect the presence of bifenthrin in a dual-choice test. Furthermore, no shortterm mortality (72 hours) was recorded on both predatory bugs. In contrast, a high mortality rate was found when they were exposed by contact to the bifenthrin-treated net for 72 hours in small cages (10 cm diameter X 3 cm high). In assays carried out under more realistic conditions of exposure, in an experimental greenhouse with cages of 25 X 25 X 60 cm high, short-term mortality (72 hours) and reproductive parameters were not affected. Lastly, in field experiments carried out in semi-commercial tunnels (8 m long X 6.5 m width X 2.6 m high), neither environmental conditions [temperature, relative humidity, ultraviolet (UV) and photosynthetically active radiation (PAR)] nor natural enemies were affected by the presence of the bifenthrin-treated net on the crop. However, results were not conclusive, mainly due to a low settlement of the released biocontrol agents, and further studies are needed in commercial greenhouses to confirm our preliminary results of compatibility. Secondly, the lethal (mortality) and sublethal effects (reproductive parameters) of six modern pesticides on the predatory bugs O. laevigatus and N. tenuis has been evaluated through laboratory and persistence experiments. Trials were carried out by residual contact, applying the insecticides to the maximum field recommended concentration on glass plates (laboratory) or plants (persistence). Insecticides were chosen as representatives of modern pesticides with a more selective mode of action on natural enemies than organochlorine, organophosphorus and carbamate insecticides. Moreover, they were also chosen because of their frequent use on horticultural crops where O. laevigatus and N. tenuis are present. All of them have been included or have been requested for inclusion in the community list of active substances on the agricultural market, Annex I of the European Directive 91/414/EEC: abamectin and emamectin (neurotoxic avermectins, chloride channel activators), deltamethrin (neutotoxic pyrethroid, sodium channel modulator, positive commercial standard), flubendiamide (neurotoxic, rianodine receptor modulator), spinosad (neurotoxic naturalyte, nicotinic acetylcholine receptor allosteric activator) and spiromesifen (inhibitors of acetyl CoA carboxylase). The study showed that O. laevigatus was more susceptible to all the studied pesticides than N. tenuis. In addition, the research results indicated no impact of flubendiamide and spiromesifen on the two natural enemies studied under laboratory conditions. Consequently, both pesticides are candidates to be included in IPM programmes where these biocontrol agents are present. On the other hand, abamectin, deltamethrin, emamectin and spinosad were not selective for both predatory bugs in laboratory experiments. However, persistence test demonstrated that in spite of the lack of physiological selectivity, these pesticides can provide ecological selectivity in some cases. Abamectin, deltamethrin, emamectin and spinosad could be compatible with N. tenuis if the mirid bug is released 4 days after the insecticide treatment on the crop. With regard to O. laevigatus, abamectin, deltamethrin and spinosad were classified as persistent in our assays, thus the study should be completed with semi-field and field experiments in order to ascertain their possible joint use in IPM programs. In contrast, emamectin could be compatible with O. laevigatus if the pirate bug is released 7 days after the insecticide treatment on the crop. Finally, the selectivity of three moulting accelerating compounds (MACs) (methoxyfenozide, tebufenozide and RH-5849) has also been evaluated on O. laevigatus and N. tenuis. In addition to laboratory experiments to evaluate the toxicity of the insecticides by residual contact and ingestion, molecular approaches were used as well. RNA of both insects was isolated, cDNA was subsequently synthesized and the complete sequence of the ligand binding domain (LBD) of the ecdysone receptor of O. laevigatus (OlEcR-LBD) and N. tenuis (NtEcR-LBD) were determined. Afterwards, the three dimensional structure of LBD was constructed. Finally, the docking of the insecticide molecules in the cavity delineated by the 12 α-helix that composed the EcRLBD was performed. In the case of N. tenuis, it should be noted that in spite of intensive efforts, we did not manage to complete the sequence for the LBD.However, a partial sequence of the LBD was obtained (helix 6-helix 11), and a strong conservation between the amino acids of N. tenuis and O. laevigatus was observed. Results showed no biological activity of methoxyfenozide, tebufenozide and RH-5849, on both predatory bugs. Moreover, modeling of the OlEcR-LBD and docking experiments also suggested that MACs were devoid of any deleterious effect on O. laevigatus. Therefore, our results indicate that these compounds could be safely applied in IPM programs in which O. laevigatus and N. tenuis are present.

Estudio teórico de propiedades termodinámicas y optoelectronicas de nuevos materiales fotovoltaicos de banda intermedia = Theoretical study of thermodynamic and optoelectronic properties of new intermediate band photovoltaic materials

Los materiales de banda intermedia han atraido la atención de la comunidad científica en el campo de la energía solar fotovoltaica en los últimos años. Sin embargo, con el objetivo de entender los fundamentos de las células solares de banda intermedia, se debe llevar a cabo un estudio profundo de la características de los materiales. Esto se puede hacer mediante un modelo teórico usando Primeros Principios. A partir de este enfoque se pueden obtener resultados tales como la estructura electrónica y propiedades ópticas, entre otras, de los semiconductores fuertemente dopados y sus precursores. Con el fin de desentrañar las estructuras de estos sistemas electrónicos, esta tesis presenta un estudio termodinámico y optoelectrónico de varios materiales fotovoltaicos. Específicamente se caracterizaron los materiales avanzados de banda intermedia y sus precursores. El estudio se hizo en términos de caracterización teórica de la estructura electrónica, la energética del sistema, entre otros. Además la estabilidad se obtuvo usando configuraciones adaptadas a la simetría del sistema y basado en la combinatoria. Las configuraciones de los sitios ocupados por defectos permiten obtener información sobre un espacio de configuraciones donde las posiciones de los dopantes sustituidos se basan en la simetría del sólido cristalino. El resultado puede ser tratado usando elementos de termodinámica estadística y da información de la estabilidad de todo el espacio simétrico. Además se estudiaron otras características importantes de los semiconductores de base. En concreto, el análisis de las interacciones de van der Waals fueron incluidas en el semiconductor en capas SnS2, y el grado de inversión en el caso de las espinelas [M]In2S4. En este trabajo además realizamos una descripción teórica exhaustiva del sistema CdTe:Bi. Este material de banda-intermedia muestra características que son distintas a las de los otros materiales estudiados. También se analizó el Zn como agente modulador de la posición de las sub-bandas prohibidas en el material de banda-intermedia CuGaS2:Ti. Analizándose además la viabilidad termodinámica de la formación de este compuesto. Finalmente, también se describió el GaN:Cr como material de banda intermedia, en la estructura zinc-blenda y en wurtztite, usando configuraciones de sitios ocupados de acuerdo a la simetría del sistema cristalino del semiconductor de base. Todos los resultados, siempre que fue posible, fueron comparados con los resultados experimentales. ABSTRACT The intermediate-band materials have attracted the attention of the scientific community in the field of the photovoltaics in recent years. Nevertheless, in order to understand the intermediate-band solar cell fundamentals, a profound study of the characteristics of the materials is required. This can be done using theoretical modelling from first-principles. The electronic structure and optical properties of heavily doped semiconductors and their precursor semiconductors are, among others, results that can be obtained from this approach. In order to unravel the structures of these crystalline systems, this thesis presents a thermodynamic and optoelectronic study of several photovoltaic materials. Specifically advanced intermediate-band materials and their precursor semiconductors were characterized. The study was made in terms of theoretical characterization of the electronic structure, energetics among others. The stability was obtained using site-occupancy-disorder configurations adapted to the symmetry of the system and based on combinatorics. The site-occupancy-disorder method allows the formation of a configurational space of substitutional dopant positions based on the symmetry of the crystalline solid. The result, that can be treated using statistical thermodynamics, gives information of the stability of the whole space of symmetry of the crystalline lattice. Furthermore, certain other important characteristics of host semiconductors were studied. Specifically, the van der Waal interactions were included in the SnS2 layered semiconductor, and the inversion degree in cases of [M]In2S4 spinels. In this work we also carried out an exhaustive theoretical description of the CdTe:Bi system. This intermediate-band material shows characteristics that are distinct from those of the other studied intermediate-band materials. In addition, Zn was analysed as a modulator of the positions of the sub-band gaps in the CuGaS2:Ti intermediate-band material. The thermodynamic feasibility of the formation of this compound was also carried out. Finally GaN:Cr intermediate-band material was also described both in the zinc-blende and the wurtztite type structures, using the symmetry-adapted-space of configurations. All results, whenever possible, were compared with experimental results.