Patterns of correlation between vehicle occupant seat pressure and anthropometry

Seat pressure is known as a major factor of seat comfort in vehicles. In passenger vehicles, there is lacking research into the seat comfort of rear seat occupants. As accurate seat pressure measurement requires significant effort, simulation of seat pressure is evolving as a preferred method. However, analytic methods are based on complex finite element modeling and therefore are time consuming and involve high investment. Based on accurate anthropometric measurements of 64 male subjects and outboard rear seat pressure measurements in three different passenger vehicles, this study investigates if a set of parameters derived from seat pressure mapping are sensitive enough to differentiate between different seats and whether they correlate with anthropometry in linear models. In addition to the pressure map analysis, H-Points were measured with a coordinate measurement system based on palpated body landmarks and the range of H-Point locations in the three seats is provided. It was found that for the cushion, cushion contact area and cushion front area/force could be modeled by subject anthropometry,while only seatback contact area could be modeled based on anthropometry for all three vehicles. Major differences were found between the vehicles for other parameters.

Determinants of second row passenger comfort

China is becoming an increasingly important automotive market. Customer’s vehicle usage, preferences and requirements differ from traditional western markets in a number of aspects – rear seat usage rates are higher, vehicles are used for business purposes as well as for private transport and rear seat usage is generally more important to Chinese customers compared to their western counterparts. The purpose of this project is to dimension and investigate these differences from an ergonomics perspective and use these results to guide the design of future products. The focus for this project will be specific to vehicles in the CD segment. More specifically, this project focuses on the second row ‘ambience’. Ambience refers to the global feeling perceived by second row passengers, and the main factors contributing to ambience are: ingress and egress comfort, seat comfort, roominess, and ease of use of the controls. In order to investigate the aforementioned parameters, an experimental study has been conducted in Shanghai, China. This experiment involved 80 healthy Chinese CD- and D-car customers. These subjects were asked to evaluate different features present in the second row environment of three different cars: A Ford Mondeo, Toyota Camry and Mercedes S-class. Various data has been collected during this experiment: First, the anthropometric dimensions of the subjects have been measured. The subjects were also asked to fill a questionnaire about demographics, their own car usage, and their perception of a various number of features present in the three tested cars. A great amount of technical data was also collected. The first part of this report presents the results given by the questionnaires. It includes Chinese demographics, vehicle usage habits, and the subjective perception of the features present in the tested cars. It also presents the results of the anthropometric measurements. This gives a first insight into Chinese customers’ habits and preferences. The second part deals with the technical data recorded during the experiment: second row seat adjustment ranges, roominess, optimal location of controls, and pressure mapping analysis. Analysis of technical data allows a deeper understanding of the factors contributing to comfort and ambience perception. Using the technical data together with the comfort ratings given by the subjects in the questionnaire, recommendations on several design parameters were provided. Finally, an experimental study of car ingress-egress has been conducted in a University laboratory controlled environment. During this study, the ingress and egress motion of 20 customers from Chinese origin was recorded using a motion capture system. The last part of this report presents the protocol and data processing that led to building an ingress-egress motion database that was provided to Ford.

Seat Comfort. M2-M3

This (seat) attribute target list and Design for Comfort taxonomy report is based on the literature review report (C3-21, Milestone 1), which specified different areas (factors) with specific influence on automotive seat comfort. The attribute target list summarizes seat factors established in the literature review (Figure 1) and subsumes detailed attributes derived from the literature findings within these factors/classes. The attribute target list (Milestone 2) then provides the basis for the “Design for Comfort��� taxonomy (Milestone 3) and helps the project develop target settings (values) that will be measured during the testing phase of the C3-21 project. The attribute target list will become the core technical description of seat attributes, to be incorporated into the final comfort procedure that will be developed. The Attribute Target List and Design for Comfort Taxonomy complete the target definition process. They specify the context, markets and application (vehicle classes) for seat development. As multiple markets are addressed, the target setting requires flexibility of variables to accommodate the selected customer range. These ranges will be consecutively filled with data in forthcoming studies. The taxonomy includes how and where the targets are derived, reference points and standards, engineering and subjective data from previous studies as well as literature findings. The comfort parameters are ranked to identify which targets, variables or metrics have the biggest influence on comfort. Comfort areas included are seat kinematics (adjustability), seat geometry and pressure distribution (static comfort), seat thermal behavior and noise/vibration transmissibility (cruise comfort) and eventually material properties, design and features (seat harmony). Data from previous studies is fine tuned and will be validated in the nominated contexts and markets in follow-up dedicated studies.

Is comfort important for optimal use of child restraints?

Suboptimal restraint use, particularly the incorrect use of restraints, is a significant and widespread problem among child vehicle occupants, and increases the risk of injury. Previous research has identified comfort as a potential factor influencing suboptimal restraint use. Both the real comfort experienced by the child and the parent’s perception of the child’s comfort are reported to influence the optimal use of restraints. Problems with real comfort may lead the child to misuse the restraint in their attempt to achieve better comfort whilst parent-perceived discomfort has been reported as a driver for premature graduation and inappropriate restraint choice. However, this work has largely been qualitative. There has been no research that objectively studies either the association between real and parental perceived comfort, or any association between comfort and suboptimal restraint use. One barrier to such studies is the absence of validated tools for quantifying real comfort in children. We aimed to develop methods to examine both real and parent-perceived comfort and examine their effects on suboptimal restraint use. We conducted online parent surveys (n=470) to explore what drives parental perceptions of their child’s comfort in restraint systems (study 1) and used data from field observation studies (n=497) to examine parent-perceived comfort and its relationship with observed restraint use (study 2). We developed methods to measure comfort in children in a laboratory setting (n=14) using video analysis to estimate a Discomfort Avoidance Behaviour (DAB) score, pressure mapping and adapted survey tools to differentiate between comfortable and induced discomfort conditions (study 3). Preliminary analysis of our recent online survey of Australian parents (study 1) indicates that 23% of parents report comfort as a consideration when making a decision to change restraints. Logistic regression modelling of data collected during the field observation study (study 2) revealed that parent-perceived discomfort was not significantly associated with premature graduation. Contrary to expectation, children of parents who reported that their child was comfortable were almost twice as likely to have been incorrectly restrained (p<0.01, 95% CI 1.24 - 2.77). In the laboratory study (study 3) we found our adapted survey tools did not provide a reliable measurement of real comfort among children. However our DAB score was able to differentiate between comfortable and induced discomfort conditions and correlated well with pressure mapping. Our results suggest that while some parents report concern about their child’s comfort, parent-reported comfort levels were not associated with restraint choice. If comfort is important for optimal restraint use, it is likely to be the real comfort of the child rather than that reported by the parent. The method we have developed for studying real comfort can be used in naturalistic studies involving child occupants to further understand this relationship. This work will be of interest to vehicle and child restraint manufacturers interested in improving restraint design for young occupants as well as researchers and other stakeholders interested in reducing the incidence of restraint misuse among children.

Study on ride comfort assessment of multiple occupants using lumped parameter analysis

Growing consumer expectations continue to fuel further advancements in vehicle ride comfort analysis including development of a comprehensive tool capable of aiding the understanding of ride comfort. To date, most of the work on biodynamic responses of human body in the context of ride comfort mainly concentrates on driver or a designated occupant and therefore leaves the scope for further work on ride comfort analysis covering a larger number of occupants with detailed modeling of their body segments. In the present study, governing equations of a 13-DOF (degrees-of-freedom) lumped parameter model (LPM) of a full car with seats (7-DOF without seats) and a 7-DOF occupant model, a linear version of an earlier non-linear occupant model, are presented. One or more occupant models can be coupled with the vehicle model resulting into a maximum of 48-DOF LPM for a car with five occupants. These multi-occupant models can be formulated in a modular manner and solved efficiently using MATLAB/SIMULINK for a given transient road input. The vehicle model and the occupant model are independently verified by favorably comparing computed dynamic responses with published data. A number of cases with different dispositions of occupants in a small car are analyzed using the current modular approach thereby underscoring its potential for efficient ride quality assessment and design of suspension systems.

Reducing energy consumption of vehicle air conditioning system by an energy management system

This paper presents an energy management system to reduce the energy consumption of a vehicle when its air conditioning system is in use. The system controls the mass flow rate of the air by dynamically adjusting the blower speed and air-gates opening under various heat and loads circumstances. Simulations were conducted for a travelling vehicle operating the air conditioning system without and with the developed energy management system. The results show that the comfort temperature within the cabin room is achieved for reduced amount of energy consumption.

Coordinated energy management of vehicle air conditioning system

Whilst air conditioning systems increase thermal comfortableness in vehicles, they also raise the energy consumption of vehicles. Achieving thermal comfort in an energy-efficient way is a difficult task requiring good coordination between engine and the air conditioning system. This paper presents a coordinated energy management system to reduce the energy consumption of the vehicle air conditioning system while maintaining the thermal comfortableness. The system coordinates and manages the operation of evaporator, blower, and fresh air and recirculation gates to provide the desired comfort temperature and indoor air quality, under the various ambient and vehicle conditions, the energy consumption can then be optimized. Three simulations of the developed coordinated energy management system are performed to demonstrate its energy saving capacity.

"Tomorrow's car" : Deakin Universities new cross vehicle that combines the best of 2 worlds

Motorbike riders are 34-times more likely to die in a crash compared to car drivers per km travelled (1). Such safety risks together with special skill requirements for the driver and much lower comfort compared to normal cars are the main reasons why motorbikes represent only a fraction of all vehicle sales in developed countries. Deakin University is developing a revolutionary cross-over fun vehicle with ultra low fuel consumption and emissions. This new vehicle generation combines the best of two worlds: the fun to drive, low cost, and small size of a scooter together with the safety, comfort and easiness to operate of a car. The result is a vehicle that is more fuel efficient than most cars or even scooters.

Various tilting cross over vehicles have been presented over the last decade that were trying to automate the tilting control of narrow vehicles to make them safer. Examples of these concepts are the Carver, Clever and in some way also the MP3 scooter from Piaggio. The problem with fully enclosed concepts like the Carver or Clever is that they require very complex and therefore also expensive tilting control systems so that the vehicles are not price competitive compared to low cost micro cars or even normal small cars. The MP3 on the other hand comes with a tilting control system which is only semi automatic so that typical car advantages - comprehensive safety features like crush zones, roll over protection, air bags, safety belts or comfort features like full weather protection including heating and cooling – can not be provided.

Deakin’s approach is quite different to the above mentioned concepts. The requirements were derived based on two different investigations: The first step was a critical evaluation of social trends and the second step was an in-depth benchmarking study of existing concepts which identified the typical strengths and weaknesses of these concepts. In a critical next step a new concept was created that addresses most of the weaknesses of existing tilting three-wheelers in a holistic approach by setting clear priority rankings for the vehicle targets, based on current trends. The priorities were set in the following order: Safety, Affordability, Fun and Efficiency (SAFE).

The key feature that enables an enclosed tilting vehicle is a fully automatic tilting control system. With an automatic tilting control system the driver does not need to put the feet on the ground to balance the vehicle when he stops, so the vehicle can be built with a full enclosure. This allows the implementation of typical car like safety features (seat belts, roll over structure, crush zones, air bags). The SafeRide™ tilting control system is a passive system that involves the driver’s balancing sense in its feedback control system. The vehicle has typical scooter like steering characteristics, where the steering is initiated through countersteering. Another safety critical design feature is the crush zone between the two front wheels which is not possible with only one front wheel or with the powertrain positioned between the front wheels, as the powertrain can’t absorb a lot of energy due to its structural stiffness and density. The passive tilting control system is quite simple and therefore makes the vehicle very affordable, an important factor for successful commercialisation.

Another advantage of integrating the human balancing senses in the feedback control of the tilting system is that the system kicks in slightly after the human balancing reacts. In some instances that can generate the typical adrenalin thrill known from riding a bike. This fun factor is quite common with many trend sports like mountain biking, surfing, roller-skating, snowboarding, or skateboarding. Some of these sports have seen very rapid growth only a short time after they have been invented. Utilising the human balancing system during driving also makes the vehicle safer as the adrenalin is produced after reaching a semi-stable driving condition that is controlled by the vehicles tilting control system, but before the vehicle reaches an unstable driving condition that can not be controlled by the vehicle but only (eventually) by the driver – if he has got the required driving skill and if he is alert enough.

Efficiency superior to most cars and scooters is achieved by the aerodynamics of a fully enclosed body structure in combination with the small frontal area of a typical scooter and the droplet shape enabled by the relatively wide front with 2 wheels and the very narrow tail with only one rear wheel. The passive tilting system also contributes to the extreme efficiency as the system only draws some small electrical power for the electronic control unit. Another feature is a low cost exhaust energy recovery system which is discussed in another paper.

Use of nonlinear asymmetrical shock absorber to improve comfort on passenger vehicles

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Dynamic analysis of road vehicle-bridge systems under turbulent wind by means of Finite Element Models

When an automobile passes over a bridge dynamic effects are produced in vehicle and structure. In addition, the bridge itself moves when exposed to the wind inducing dynamic effects on the vehicle that have to be considered. The main objective of this work is to understand the influence of the different parameters concerning the vehicle, the bridge, the road roughness or the wind in the comfort and safety of the vehicles when crossing bridges. Non linear finite element models are used for structures and multibody dynamic models are employed for vehicles. The interaction between the vehicle and the bridge is considered by contact methods. Road roughness is described by the power spectral density (PSD) proposed by the ISO 8608. To consider that the profiles under right and left wheels are different but not independent, the hypotheses of homogeneity and isotropy are assumed. To generate the wind velocity history along the road the Sandia method is employed. The global problem is solved by means of the finite element method. First the methodology for modelling the interaction is verified in a benchmark. Following, the case of a vehicle running along a rigid road and subjected to the action of the turbulent wind is analyzed and the road roughness is incorporated in a following step. Finally the flexibility of the bridge is added to the model by making the vehicle run over the structure. The application of this methodology will allow to understand the influence of the different parameters in the comfort and safety of road vehicles crossing wind exposed bridges. Those results will help to recommend measures to make the traffic over bridges more reliable without affecting the structural integrity of the viaduct

Application of active and passive suspension techniques to improve high speed ground vehicle performance - phase II. Final report.

Transportation Department, Office of University Research, Washington, D.C.

Assessment of vehicle safety problems for special driving populations. Final report.

National Highway Traffic Safety Administration, Washington, D.C.

Quantification of motor vehicle emission factors from on road measurements

Assessment and prediction of the impact of vehicular traffic emissions on air quality and exposure levels requires knowledge of vehicle emission factors. The aim of this study was quantification of emission factors from an on road, over twelve months measurement program conducted at two sites in Brisbane: 1) freeway type (free flowing traffic at about 100 km/h, fleet dominated by small passenger cars - Tora St); and 2) urban busy road with stop/start traffic mode, fleet comprising a significant fraction of heavy duty vehicles - Ipswich Rd. A physical model linking concentrations measured at the road for specific meteorological conditions with motor vehicle emission factors was applied for data analyses. The focus of the study was on submicrometer particles; however the measurements also included supermicrometer particles, PM2.5, carbon monoxide, sulfur dioxide, oxides of nitrogen. The results of the study are summarised in this paper. In particular, the emission factors for submicrometer particles were 6.08 x 1013 and 5.15 x 1013 particles per vehicle-1 km-1 for Tora St and Ipswich Rd respectively and for supermicrometer particles for Tora St, 1.48 x 109 particles per vehicle-1 km-1. Emission factors of diesel vehicles at both sites were about an order of magnitude higher than emissions from gasoline powered vehicles. For submicrometer particles and gasoline vehicles the emission factors were 6.08 x 1013 and 4.34 x 1013 particles per vehicle-1 km-1 for Tora St and Ipswich Rd, respectively, and for diesel vehicles were 5.35 x 1014 and 2.03 x 1014 particles per vehicle-1 km-1 for Tora St and Ipswich Rd, respectively. For supermicrometer particles at Tora St the emission factors were 2.59 x 109 and 1.53 x 1012 particles per vehicle-1 km-1, for gasoline and diesel vehicles, respectively.