Métodos "verdes" de produção de nanomateriais que promovem nanotecnologias sustentáveis

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia Química

Estudo da pirólise de misturas de resíduos de plásticos, pneus e biomassa

Dissertação para obtenção do Grau de Doutor em Engenharia Química e Bioquímica

Estudo da utilização do protocolo PROFIBUS para aplicações com grande número de estações escravas

Neste trabalho são descritas a arquitetura e as propriedades características do protocolo PROFIBUS, nome dado a um entre os diversos protocolos existentes na área industrial. Utilizando uma versão do protocolo PROFIBUS desenvolvida no Laboratório de Instrumentação Eletro-Eletrônica da Universidade Federal do Rio Grande do Sul foi implementada uma rede composta por uma estação mestre e até 96 estações escravas. A fim de analisar o Tempo de Ciclo de Mensagem e o Tempo de Reação do Sistema foram realizados diversos testes, variando a taxa de comunicação utilizada, o tamanho dos quadros de comunicação e a quantidade de estações escravas que compunham a rede. No final foi feita uma comparação entre os valores práticos obtidos e valores calculados a partir de fórmulas teóricas. Os valores práticos obtidos possibilitam determinar a viabilidade da utilização desta rede em diversas aplicações reais.

Os efeitos da política monetária sobre a poupança financeira, o emprego, a produção e o consumo: 1990-1996

Este trabalho tem por objetivo estimar o tempo que diferentes segmentos econômicos levam para responder a mudanças na taxa de juros. A investigação abrangeu o período de janeiro de 1990 a junho de 1996, compreendendo, portanto, o Plano Collor e os dois anos iniciais do Plano Real. O intuito de medir essa defasagem temporal prende-se ao fato de que, no Brasil, tornou-se hábito adotar, como parâmetros de tempo de resposta à política monetária, aqueles encontrados nos Estados Unidos. Naquele país, o tempo de reação da sociedade à política monetária tem sido estimado, freqüentemente, entre 6 e 12 meses. Este estudo encontrou que, no Brasil, dependendo do segmento (poupança, consumo ou produção), o tempo de resposta é imediato, podendo chegar a 2 ou 3 meses. Para estimar a defasagem de tempo, foi usada a técnica de correlações cruzadas entre variáveis pré-filtradas pelos respectivos ARIMAS.

Obtenção de alfa-olefinas em reações de oligomerização do eteno utilizando complexos de níquel em meio homogêneo e bifásico

Neste trabalho são descritos estudos comparativos de reações de oligomerização do etileno utilizando complexos do tipo: Ni-[P^O] e Ni-[Diimina] (na presença de MAO como cocatalisador). A pesquisa foi realizada com o objetivo de verificar e comparar o comportamento dos dois complexos em estudo, quando estes passam do meio homogêneo para o meio bifásico (na presença de um líquido iônico). O líquido iônico utilizado é o tetrafluorborato de 1-butil-3-metilimidazol. Foram avaliados parâmetros reacionais como pressão, temperatura, tempo de reação, velocidade de agitação e volume de líquido iônico para o catalisador Ni-[P^O] nos meios homogêneo e bifásico. Para o precursor Ni-[Diimina], os parâmetros avaliados foram pressão e temperatura nos dois meios. Os produtos obtidos são olefinas lineares e ramificadas, principalmente α-olefinas; com faixa de distribuição de C4 a C20 (Distribuição Shulz-Flowry). As atividades obtidas nos ciclos de reações variam entre 21 h-1 a 32.772 h-1, e os resultados são interpretados envolvendo os mecanismos de reação. Devido as diferenças existentes entre nos complexos em estudo, verifica-se diferentes atividades e diferentes faixas de produtos oligoméricos. O comportamento obtido para cada complexo depende diretamente dos parâmetros reacionais utilizados, além do meio ao qual foram submetidos durante as reações.

Zeólitas de cinzas de carvão : síntese e uso

Cinza de carvão é tão somente o resíduo sólido industrial de maior geração no sul do Brasil: cerca de 1,7 milhões de t/ano, sendo que menos de 30% deste total são reutilizadas, principalmente pelo setor de construção civil. Nesta tese foi estudado o processo hidrotérmico em meio alcalino para a síntese de zeólitas utilizando cinzas de carvão como matéria-prima. As variáveis estudadas foram: tipo e composição das cinzas de carvão (dezessete tipos), tipo e concentração do meio reacional alcalino (NaOH e KOH 2, 3,5 e 5 mol/L) e , temperatura de reação e conseqüentemente da pressão (60, 100 e 150oC para NaOH e 100, 150 e 200oC para KOH), tempo de reação e relação solução alcalina/cinzas de carvão (ou concentração inicial de cinzas em solução). Foram gerados sete tipos diferentes de zeólitas quando o meio reacional era o NaOH: zeólitas A, P, X, sodalita, cancrinita, noselita e chabazita, já quando o meio reacional foi o KOH foram gerados quatro tipos de zeólitas: zeólitas F, L, W e chabazita. A partir do estudo amplo, que também contou com uma etapa de otimização, foram escolhidos dois produtos zeolíticos potássicos, para teste de uso em solos, para o cultivo de plantas, nas seguintes condições experimentais: menor temperatura possível (100oC) e no tempo mínimo (3 dias) de reação, e assim nas duas concentrações possíveis (3,5 e 5 mol/L) variando-se a relação solução/cinzas de modo a se obterem produtos diferentes e com as duas zeólitas de maior ocorrência no estudo amplo, quais sejam, zeólita W e chabazita. Assim os produtos 50K2 (zeólita W) e 35K6 (chabazita contaminada com zeólita W) foram utilizados com sucesso como fonte de K e, complementar ou total de N no cultivo de plantas de aveia Foram realizados estudos específicos para observação do efeito dos principais elementos constituintes das cinzas de carvão: Fe e Ca. O efeito do aumento da concentração do Fe não ficou perfeitamente estabelecido, porém o efeito da adição de calcário ao combustor, ou seja, do aumento da concentração de Ca, Mg e S foi perfeitamente estabelecido, sendo que para as zeólitas F e sodalita foi positivo e negativo para as zeólitas P e chabazita sódica. Metodologias de dissolução de cinzas também foram estudados: a temperatura ambiente sob agitação e por fusão prévia das cinzas com a base. Os efeitos foram muitos e dependentes da especificidade de cada caso. Quando a reação de zeolitização foi acompanhada por 24 horas, foi possível observar o inicio da cristalização das zeólitas, bem como a variação ao longo do tempo do tipo gerado e o tempo para o máximo de Si em solução.

Recuperação do cromo contido nas cinzas provenientes da incineração de resíduos sólidos das indústrias coureira e calçadista visando a obtenção de cromato de sódio (VI)

O processo de transformação da pele em couro envolve uma seqüência complexa de reações químicas e processos mecânicos, no qual o curtimento representa fundamental estágio, por propiciar à pele características como qualidade, estabilidade hidrotérmica e excelentes propriedades para uso. O sulfato básico de cromo trivalente é o agente curtente predominantemente empregado no curtimento de peles em todo o mundo. É produzido a partir do cromato de sódio, industrialmente obtido do minério de cromo. Consideráveis quantidades de resíduos sólidos contendo cromo são geradas pelas indústrias coureira e calçadista. Estes resíduos tem sido motivo de preocupação constante, uma vez que são considerados perigosos devido a presença do cromo. O processo de incineração destes resíduos é uma importante alternativa a ser considerada, em decorrência de suas características de redução de massa, volume e possibilidade de aproveitamento da energia térmica dos gases de combustão. O processo de incineração dos resíduos das indústrias coureira e calçadista dá origem a cinzas contendo cerca de 40% de cromo que pode ser submetida a um processo de recuperação. Este trabalho apresenta os resultados da pesquisa sobre a utilização das cinzas, provenientes da incineração dos resíduos sólidos da indústria coureira e da indústria calçadista, para a produção de cromato de sódio(VI). No processo de planejamento e de condução dos experimentos foram utilizadas as técnicas de Planejamento Fatorial 2k, Metodologia de Superfície de Resposta e Análise de Variância na avaliação da produção de cromato de sódio(VI). Os fatores investigados foram: temperatura, taxa de aquecimento, tempo de reação, vazão de ar e quantidade de dolomita. A partir das variáveis selecionadas identificaram-se como parâmetros importantes a temperatura e a taxa de aquecimento. As superfícies de resposta tridimensionais obtidas a partir dos modelos de segunda ordem ajustados aos dados experimentais, apresentaram o comportamento do efeito conjugado dos fatores temperatura e taxa de aquecimento sobre a variável resposta grau de oxidação, desde a temperatura de inicio da reação química até a temperatura limite utilizada industrialmente. As condições de operação do processo de produção de cromato de sódio(VI) foram otimizadas. Os níveis ótimos dos fatores de controle aplicados as cinzas dos resíduos da indústria calçadista, geradas em uma planta piloto com incinerador de leito fixo, com tecnologia de gaseificação e combustão combinadas, apresentaram um grau de oxidação superior a 96% para as cinzas coletadas no ciclone e de 99,5% para as cinzas coletas no reator de gaseificação. Os resíduos sólidos, as cinzas e o produto de reação foram caracterizados por análises químicas, fluorescência de raio-X, microscopia eletrônica de varredura e difração de raio-X.

Síntese e caracterização de TaC e óxido misto de tântalo e cobre nanoestruturados a partir do precursor oxálico de tântalo através de reações gás-sólido e sólido-sólido a baixa temperatura

The research and development of nanostructured materials have been growing significantly in the last years. These materials have properties that were significantly modified as compared to conventional materials due to the extremely small dimensions of the crystallites. The tantalum carbide (TaC) is an extremely hard material that has high hardness, high melting point, high chemical stability, good resistance to chemical attack and thermal shock and excellent resistance to oxidation and corrosion. The Compounds of Tantalum impregnated with copper also have excellent dielectric and magnetic properties. Therefore, this study aimed to obtain TaC and mixed tantalum oxide and nanostructured copper from the precursor of tris (oxalate) hydrate ammonium oxitantalato, through gas-solid reaction and solid-solid respectively at low temperature (1000 ° C) and short reaction time. The materials obtained were characterized by X-ray diffraction (XRD), Rietveld refinement, Scanning Electron Microscopy (SEM), Spectroscopy X-Ray Fluorescence (XRF), infrared spectroscopy (IR), thermogravimetric (TG), thermal analysis (DTA) and BET. Through the XRD analyses and the Reitiveld refinement of the TaC with S = 1.1584, we observed the formation of pure tantalum carbide and cubic structure with average crystallite size on the order of 12.5 nanometers. From the synthesis made of mixed oxide of tantalum and copper were formed two distinct phases: CuTa10O26 and Ta2O5, although the latter has been formed in lesser amounts

Pirólise termoquímica de pós da fibra de coco seco em um reator de cilindro rotativo para produção de bio-óleo

This master thesis aims at developing a new methodology for thermochemical degradation of dry coconut fiber (dp = 0.25mm) using laboratory rotating cylinder reactor with the goal of producing bio-oil. The biomass was characterized by infrared spectroscopy with Fourier transform FTIR, thermogravimetric analysis TG, with evaluation of activation energy the in non-isothermal regime with heating rates of 5 and 10 °C/min, differential themogravimetric analysis DTG, sweeping electron microscopy SEM, higher heating value - HHV, immediate analysis such as evaluated all the amounts of its main constituents, i.e., lignin, cellulose and hemicelluloses. In the process, it was evaluated: reaction temperature (450, 500 and 550oC), carrier gas flow rate (50 and 100 cm³/min) and spin speed (20 and 25 Hz) to condensate the bio-oil. The feed rate of biomass (540 g/h), the rotation of the rotating cylinder (33.7 rpm) and reaction time (30 33 min) were constant. The phases obtained from the process of pyrolysis of dry coconut fiber were bio-oil, char and the gas phase non-condensed. A macroscopic mass balance was applied based on the weight of each phase to evaluate their yield. The highest yield of 20% was obtained from the following conditions: temperature of 500oC, inert gas flow of 100 cm³/min and spin speed of 20 Hz. In that condition, the yield in char was 24.3%, non-condensable gas phase was 37.6% and losses of approximately 22.6%. The following physicochemical properties: density, viscosity, pH, higher heating value, char content, FTIR and CHN analysis were evaluated. The sample obtained in the best operational condition was subjected to a qualitative chromatographic analysis aiming to know the constituents of the produced bio-oil, which were: phenol followed by sirigol, acetovanilona and vinyl guaiacol. The solid phase (char) was characterized through an immediate analysis (evaluation of moisture, volatiles, ashes and fixed carbon), higher heating value and FTIR. The non-condensing gas phase presented as main constituents CO2, CO and H2. The results were compared to the ones mentioned by the literature.

Avaliação de metodologia de preparo de amostra de petróleo por digestão ácida auxiliada por microondas para determinação de metais por ICP-OES

This project describes a methodology optimization that would allow for a more efficient microwave assisted digestion process for petroleum samples. With the possible chance to vary various factors at once to see if any one factor was significant enough in the answers, experimental planning was used. Microwave assisted digestion allows, through the application of potency, an increasing number of collisions between the HNO3 and H2O2 molecules, favoring sample opening for complex matrixes. For this, a 24 factorial experimental planning was used, varying potency, time and the volumes for HNO3 65% and H2O2 30%. To achieve the desired answers, several elements were monitored (C, Cu, Cr, Fe, Ni, Zn and V) through Inductively coupled plasma atomic emission spectroscopy (ICP-OES). With this initial study it was noticed that the HNO3 was not a significant factor for any of the statistical studies for any of the analytes and the other 3 factors and their interactions showed statistical significance. A Box Behnken experimental planning was used taking in consideration 3 factors: H2O2 volume, time (min) and Potency (W), Nitric Acid kept at 4mL for a mass of 0,1g of petroleum. The results were extremely satisfying showing higher efficiency in the digestion process and taking in a responsibility between the answers for each analyte and the carbon monitoring was achieved in the following conditions: 7mL of H2O2, 700 Watts of potency and a reaction time of 7 minutes with 4mL de HNO3 for a mass of 0,1g of petroleum. The optimized digestion process was applied to four different petroleum samples and the analytes determined by ICP-OES

Produção de biodiesel a partir de óleo de coco (Cocos nucifera L

The production of biodiesel has become an important and attractive process for the production of alternative fuels. This work presents a study of the biodiesel production from coconut oil (Cocos nucifera L.), by two routes: direct transesterification using NaOH as catalyst and esterification (with H2SO4) followed by basic transesterification. The reactor was built in pirex with 1L of capacity and was equipped with a jacket coupled with a thermostatic bath to temperature control, a mecanical stirring is also present in the reactor. The analysis of oil composition was carried out by gas chromatography and esters compounds were identified. The parameters of molar ratio oil/alcohol, reaction time and temperature were studied and their influence on the conversion products was evaluated using experimental planning (23). The molar ratio was the most significant variable by the statistical planning analysis. Conversions up to 85.3% where achived in the esterification/transesterification, with molar ratio 1:6 at 60ºC and 90 minutes of reaction. For the direct transesterification, route conversions up 87.4% eas obtained using 1:6.5 molar ratio at 80ºC and 60 minutes of reaction. The Coconut oil was characterized by their physic chemical properties and key constituents of the oil. The lauric acid was the main constituint and the oil showed high acidity. The biodiesel produced was characterized by its main physicochemical properties, indicating satisfactory results when compared to standard values of National Petroleum Agency. The work was supplemented with a preliminary assessment of the reaction kinetic

Extração enzimática de óleo e produção in situ de biodiesel a partir da Moringa oleífera Lam

With the growth and development of modern society, arises the need to search for new raw materials and new technologies which present the "clean" characteristic, and do not harm the environment, but can join the energy needs of industry and transportation. The Moringa oleifera Lam, plant originating from India, and currently present in the Brazilian Northeast, presents itself as a multi-purpose plant, can be used as a coagulant in water treatment, as a natural remedy and as a feedstock for biodiesel production. In this work, Moringa has been used as a raw material for studies on the extraction and subsequently in the synthesis of biodiesel. Studies have been conducted on various techniques of Moringa oil extraction (solvents, mechanical pressing and enzymatic), being specially developed an experimental design for the aqueous extraction with the aid of the enzyme Neutrase© 0.8 L, with the aim of analyzing the influence variable pH (5.5-7.5), temperature (45-55°C), time (16-24 hours) and amount of catalyst (2-5%) on the extraction yield. In relation to study of the synthesis of biodiesel was initially carried out a conventional transesterification (50°C, KOH as a catalyst, methanol and 60 minutes reaction). Next, a study was conducted using the technique of in situ transesterification by using an experimental design variables as temperature (30-60°C), catalyst amount (2-5%), and molar ratio oil / ethanol (1:420-1:600). The extraction technique that achieved the highest extraction yield (35%) was the one that used hexane as a solvent. The extraction using 32% ethanol obtained by mechanical pressing and extraction reached 25% yield. For the enzymatic extraction, the experimental design indicated that the extraction yield was most affected by the effect of the combination of temperature and time. The maximum yield obtained in this extraction was 16%. After the step of obtaining the oil was accomplished the synthesis of biodiesel by the conventional method and the in situ technique. The method of conventional transesterification was obtained a content of 100% and esters by in situ technique was also obtained in 100% in the experimental point 7, with a molar ratio oil / alcohol 1:420, Temperature 60°C in 5% weight KOH with the reaction time of 1.5 h. By the experimental design, it was found that the variable that most influenced the ester content was late the percentage of catalyst. By physico-chemical analysis it was observed that the biodiesel produced by the in situ method fell within the rules of the ANP, therefore this technique feasible, because does not require the preliminary stage of oil extraction and achieves high levels of esters

Equilíbrio líquido-líquido para o sistema biodiesel de óleo de semente de melão (Cucumis melo l.) + metanol + glicerina

Rio Grande do Norte, northeast state from Brazil, it is the greatest producer and exporter of yellow melon, well known as Spanish melon. Despite the consumption of this fruit to be mainly its pulp, melon seeds are an important source of lipids considered an industrial residue it has been discharge product. The use of oilseeds in order to produce biodiesel establishes an important raw material and the increase of its production promotes the national development of the agriculture. In this background, the aim of this work has been to use oil from seeds of yellow melon to produce biodiesel and to accomplish a study of the phase equilibrium of the system evolving biodiesel, methanol and glycerin. The biodiesel was obtained by oil transesterification through methylic route with molar ratio 1:9.7 (oil:alcohol) and with a mass of NaOH of 0.5% from the oil mass; the reaction time was 73 minutes at 55 °C. A yield of 84.94% in biodiesel was achieved. The equilibria data present a well-characterized behavior with a great region of two phases. The tie lines indicate that methanol has a best solubility in the phase that is rich in glycerin. Consistency of the experimental data was made based on Othmer-Tobias and Hand correlations which values above 0.99 were found to correlation coefficients, this fact confers a good thermodynamic consistency to the experimental data. NRTL and UNIQUAC models were employed to predict liquid-liquid equilibrium of this system. It was observed a better concordance of the results when NRTL was applied (standard deviation 1.25%) although the UNIQUAC model has presented a quite satisfactory result either (standard deviation 2.70%). The NRTL and UNIQUAC models were also used to evaluate the effect of temperature in the range of 328 K to 358 K, in which a little change in solubility with respect to the data obtained at 298 K was observed, thus being considered negligible the effect of temperature

Degradação fotoquímica de efluentes industriais contendo polipropileno e isoniazida

One of the main impacts to the environment is the water pollution, where the industrial sector is one of the main sources of this problem. In order to search for a solution, the industrial sector is looking forward to new technologies to treat its wastewaters with the goal to reuse the water in the own process. In this mode, the treatment presents a reduction in its costs with the water suply. One of these technologies that are getting more and more applications is the advanced oxidative processes (AOP´s). In this work two industrial wastewaters have been studied, i.e., containing polymers and pharmacus. In the case of the wastewaters with polymers the UV/H2O2 process has been applied with a systematic series of experiments, using irradiation from a mercury lamp and also solar. The following variables of the UV/H2O2 process for the polymers wastewaters have been studied systematically with the lamp reactor: mode of addition of hydrogen peroxide, temperature, time of reaction, hydrogen peroxide concentration and power of the lamp (80, 125, 250 and 400W). The results demonstrated to be satisfactory, obtaining rates of organic charge removal of 100% in 120 minutes of reaction. The studied variables for the experiments with solar irradiation using polymers wastewaters were only the time of reaction, the mode of addition and concentration of the hydrogen peroxide. The results with the solar irradiation demonstrated to be not satisfactory, reaching maximum of 22% of TOC removal in 240 minutes of reaction. This is in accordance with the fact that the solar source has only 5% of low UV irradiation. With respect to the photodegradation of the pharmacus wastewaters, the process UV/H2O2 and photo-Fenton have been applied. As a source of photons, in this case, a mercury UV lamp of 80 W has been used. The studied variables for the experiments with artificial irradiation with the pharmacus wastewaters were: initial concentration of the pollutant, concentration of Fe2+ and time of reaction. The results demonstrated a degree of degradation fairly satisfactory, showing a maximum conversion value of 46% in 120 minutes

Oxidação úmida de fenóis com catalisadores de ferro suportado em argilominerais em reator de leito de lama (slurry)

The wet oxidation of organic compounds with CO2 and H2O has been demonstrated to be an efficient technique for effluent treatment. This work focuses on the synthesis, characterization and catalytic performance of Fe-MnO2/CeO2, K-MnO2/CeO2/ palygorskite and Fe/ palygorskite toward the wet oxidative degradation of phenol. The experiments were conducted in a sludge bed reactor with controlled temperature, pressure and stirring speed and sampling of the liquid phase. Experiments were performed on the following operating conditions: temperature 130 ° C, pressure 20.4 atm, catalyst mass concentration of 5 g / L initial concentration of phenol and 0.5 g / L. The catalytic tests were performed in a slurry agitated reactor provided with temperature, pressure and agitation control and reactor liquid sampling. The influences of iron loaded on the support (0.3; 7 and 10%, m/m) and the initial pH of the reactant medium (3.1; 6.8; 8.7) were studied. The iron dispersion on the palygorskite, the phase purity and the elemental composition of the catalyst were evaluated by X-Ray Difraction (XRD), Scanning Electron Microscopy (SEM) and X-Ray Flourescence (XRF). The use of palygorskite as support to increase the surface area was confirmed by the B.E.T. surface results. The phenol degradation curves showed that the Fe3+ over palygorskite when compared with the other materials tested has the best performance toward the (Total Organic carbonic) TOC conversion. The decrease in alkalinity of the reaction medium also favors the conversion of TOC. The maximum conversion obtained from the TOC with the catalyst 3% Fe / palygorskite was around 95% for a reaction time of 60 minutes, while reducing the formation of acids, especially acetic acid. With products obtained from wet oxidation of phenol, hydroquinone, p-benzoquinone, catechol and oxalic acid, identified and quantified by High Performance Liquid Chromatography was possible to propose a reaction mechanism of the process where the phenol is transformed into the homogeneous and heterogeneous phase in the other by applying a kinetic model, Langmuir-Hinshelwood type, with evaluation of kinetic constants of different reactions involved.