Dielectric properties of c-axis oriented Zn1-xMgxO thin films grown by multimagnetron sputtering

Zn1−xMgxO (x = 0.3) thin films have been fabricated on Pt/TiO2/SiO2/Si substrates using multimagnetron sputtering technique. The films with wurtzite structure showed a (002) preferred orientation. Ferroelectricity in Zn1−xMgxO films was established from the temperature dependent dielectric constant and the polarization hysteresis loop. The temperature dependent study of dielectric constant at different frequencies exhibited a dielectric anomaly at 110 °C. The resistivity versus temperature characteristics showed an anomalous increase in the vicinity of the dielectric transition temperature. The Zn1−xMgxO thin films exhibit well-defined polarization hysteresis loop, with a remanent polarization of 0.2 μC/cm2 and coercive field of 8 kV/cm at room temperature.

Potential source identification for aerosol concentrations over a site in Northwestern India

The collocated measurements of aerosols size distribution (ASD) and aerosol optical thickness (AOT) are analyzed simultaneously using Grimm aerosol spectrometer and MICROTOP II Sunphotometer over Jaipur, capital of Rajasthan in India. The contrast temperature characteristics during winter and summer seasons of year 2011 are investigated in the present study. The total aerosol number concentration (TANC, 0.3-20 mu m) during winter season was observed higher than in summer time and it was dominated by fine aerosol number concentration (FANC < 2 mu m). Particles smaller than 0.8 mu m (at aerodynamic size) constitute similar to 99% of all particles in winter and similar to 90% of particles in summer season. However, particles greater than 2 mu m contribute similar to 3% and similar to 0.2% in summer and winter seasons respectively. The aerosols optical thickness shows nearly similar AOT values during summer and winter but corresponding low Angstrom Exponent (AE) values during summer than winter, respectively. In this work, Potential Source Contribution Function (PSCF) analysis is applied to identify locations of sources that influenced concentrations of aerosols over study area in two different seasons. PSCF analysis shows that the dust particles from That Desert contribute significantly to the coarse aerosol number concentration (CANC). Higher values of the PSCF in north from Jaipur showed the industrial areas in northern India to be the likely sources of fine particles. The variation in size distribution of aerosols during two seasons is clearly reflected in the log normal size distribution curves. The log normal size distribution curves reveals that the particle size less than 0.8 pm is the key contributor in winter for higher ANC. (C) 2015 Elsevier B.V. All rights reserved.

连续工作的体布拉格光栅外腔半导体激光器的温度特性

对体布拉格光栅(VBG)作为波长选择元件的外腔半导体激光器的波长锁定进行了实验研究,报道了连续运转输出功率达43.5 W的半导体激光器阵列的体布拉格光栅波长锁定实验结果,给出了不同热沉温度下的稳定的波长锁定结果,说明采用体布拉格光栅外腔将减小半导体激光器的温控压力。实验中发现,随着注入电流的增大,输出激光功率逐渐增强,锁定的激射波长向长波长方向偏移。在输出功率为34.5 W时,波长红移约0.56 nm。这一移动与实验测量的体布拉格光栅的温度特性相吻合。连续和高占空比运行、高输出功率情况下,在器件的设计和使用时应该考虑这一效应。

Distribuição das assembleias de girinos associadas a riachos da Reserva Ecológica de Guapiaçu, Cachoeiras de Macacú, Rio de Janeiro, Brasil

Os girinos são organismos diversos e abundantes nos pequenos riachos de cabeceira de florestas tropicais e constituem importantes componentes da diversidade biológica, da trófica e funcional dos sistemas aquáticos. Diferentes características estruturais e limnológicas dos ambientes aquáticos influenciam a organização das assembleias de girinos. Embora o estágio larvar dos anuros seja o mais vulnerável de seu ciclo de vida, sujeito a elevadas taxas de mortalidade, as pesquisas sobre girinos na região neotropical ainda são pouco representativas diante da elevada diversidade de anfíbios desta região e ferramentas que permitam a sua identificação ainda são escassas. Nesta tese, dividida em três capítulos, apresento uma compilação das informações relacionadas aos principais fatores que afetam as assembleias de girinos na região tropical (Capítulo 1), a caracterização morfológica dos girinos encontrados nos riachos durante o estudo e uma proposta de chave dicotômica de identificação (Capítulo 2) e avalio a importância relativa da posição geográfica e da variação temporal de fatores ambientais locais sobre as assembleias de girinos, assim como a correlação entre as espécies de girinos e as variáveis ambientais de 10 riachos, ao longo de 15 meses, nas florestas da REGUA (Capítulo 3). Há pelo menos oito tendências relacionadas à distribuição das assembleias de girinos: (1) o tamanho dos riachos e a diversidade de microhabitats são importantes características abióticas influenciando a riqueza e a composição de espécies; (2) em poças, o gradiente de permanência (e.g., hidroperíodo) e a heterogeneidade do habitat são os principais fatores moldando as assembleias de girinos; (3) a composição de espécies parece ser um parâmetro das assembleias mais relevante do que a riqueza de espécies e deve ser primeiramente considerado durante o planejamento de ações conservacionistas de anuros associados a poças e riachos; (4) a predação parece ser a interação biótica mais importante na estruturação das assembleias de girinos, com predadores vertebrados (e.g. peixes) sendo mais vorazes em habitats permanentes e predadores invertebrados (e.g. larvas de odonata) sendo mais vorazes em ambientes temporários; (5) os girinos podem exercer um efeito regulatório, predando ovos e girinos recém eclodidos; (6) o uso do microhabitat varia em função da escolha do habitat reprodutivo pelos adultos, presença de predadores, filogenia, estágio de desenvolvimento e heterogeneidade do habitat; (7) os fatores históricos restringem os habitats reprodutivos que uma espécie utiliza, impondo restrições comportamentais e fisiológicas; (8) a variação temporal nos fatores bióticos (e.g., fatores de risco), abióticos (e.g., distribuição de chuvas), e no padrão de reprodução das espécies pode interferir na estrutura das assembleias de girinos tropicais. A variação temporal na heterogeneidade ambiental dos riachos da REGUA resultou na previsibilidade das assembleias locais de girinos, sendo que os parâmetros ambientais explicaram 23% da variação na sua composição. Os parâmetros espaciais explicaram uma porção menor da variação nas assembleias (16%), enquanto uma porção relativamente elevada da variação temporal da heterogeneidade ambiental foi espacialmente estruturada (18%). As variáveis abióticas que apresentaram as maiores correlação com a composição das assembleias de girinos foram a proporção de folhiço e de rochas no fundo do riacho, e secundariamente a profundidade, a condutividade e a temperatura. O gradiente gerado pela proporção de folhiço e de rochas representou a transição entre riachos permanentes e intermitentes. Este gradiente proporcionou o turnover de espécies, o qual também seguiu um gradiente de condutividade, temperatura, profundidade, e em menor extensão, de hidroperíodo e largura, que estiveram fortemente associado ao grau de permanência dos riachos. Estes resultados corroboram tanto a hipótese do controle ambiental, como do controle biótico de comunidades e indicam que a variação temporal da heterogeneidade ambiental e a variação na posição geográfica são importantes para a estruturação local de assembleias de girinos da REGUA. Os resultados também permitiram distinguir entre assembleias de girinos exclusivas de riachos permanentes, exclusivas de riachos intermitentes e aquelas registradas nos dois tipos de riachos. Os resultados deste capítulo são relevantes para compreender em que extensão os efeitos da variação temporal na heterogeneidade ambiental e de processos espaciais afetam localmente a estruturação de assembleias de girinos.

Material growth and device fabrication of highly strained InGaAs/InGaAsP long wavelength distributed feedback lasers

1.6-1.7 mu m highly strained InGaAs/InGaAsP distributed feedback lasers was grown and fabricated by low pressure mentalorganic chemical vapor deposition. High quality highly strained InGaAs/InP materials were obtained by using strain buffer layer. Four pairs of highly strained quantum wells were used in the devices and carrier blocking layer was used to improve the temperature characteristics of the devices. The uncoated 1.66 mu m and 1.74 mu m lasers with ridge wave guide 3 mu m wide have low threshold current (< 15mA) and high output power (> 14mW at 100mA). In the temperature range from 10 degrees C to 40 degrees C, the characteristic temperature T-0 of the 1.74 mu m laser is 57K, which is comparable to that of the 1.55 mu m-wavelength InGaAsP/InP-DFB laser.

Stochastic resonance in quantum-well semiconductor lasers

The quantum well (QW) semiconductor lasers have become main optical sources for optical fibre communication systems because of their higher modulation speed, broader modulation bandwidth and better temperature characteristics. In order to improve the quality of direct-modulation by means of the stochastic resonance (SR) mechanism in QW semiconductor lasers, we investigate the behaviour of the SR in direct-modulated QW semiconductor laser systems. Considering the cross-correlated carrier noise and photon noise, we calculate the power spectrum of the photon density and the signal-to-noise ratio (SNR) of the direct-modulated laser system by using the linear approximation method. The results indicate that the SR always appears in the dependence of the SNR on the bias current density, and is strongly affected by the cross-correlation coefficient of the carrier and photon noises, the frequency of modulation signal, and the photon lifetime in the laser cavity.

Micro Fabry-Perot interferometers in silica fibers machined by femtosecond laser

Micro Fabry-Perot (F-P) interferometers (MFPIs) are machined in a single-mode fiber (SMF) and a photonic crystal fiber (PCF) by using a near-infrared femtosecond laser, respectively. The strain and temperature characteristics of the two MFPIs with an identical cavity length are investigated and the experimental results show that the strain sensitivity of the PCF-based MFPI is smaller than that of the SMF-based MFPI due to their different waveguide structures, while the two MFPIs have close temperature sensitivities which are much smaller than that of an in-line SMF etalon sensor reported previously. These MFPIs in silica fibers are compact, stable, inexpensive, capable for mass-production and easy fabrication, offering great potentials for wide sensing applications. (c) 2007 Optical Society of America.

Thermal analysis and structural investigation of different dental composite resins

The structural and thermal properties of three different dental composite resins, Filtek (TM) Supreme XT, Filtek (TM) Z-250 and TPHA (R)(3) were investigated in this study. The internal structures of uncured and cured resins with blue light-emitting diodes (LEDs) were examined by Micro-Raman spectroscopy. Thermal analysis techniques as DSC, TG and DTG methods were used to investigate the temperature characteristics, as glass transition (T (g) ), degradation, and the thermal stability of the resins. The results showed that the TPHA (R)(3) and Filtek (TM) Supreme XT presented very similar T (g) values, 48 and 50A degrees C, respectively, while the Filtek (TM) Z-250 composite resin presented a higher one, 58A degrees C. AFM microscope was utilized in order to analyze the sample morphologies, which possess different fillers. The composed resin Filtek (TM) Z-250 has a well interconnected more homogeneous morphology, suggesting a better degree of conversion correlated to the glass phase transition temperature. The modes of vibration of interest in the resin were investigated using Raman spectroscopy. It was possible to observe the bands representative for the C=C (1630 cm(-1)) and C=O(1700 cm(-1)) vibrations were studied with respect to their compositions and polymerization. It was observed that the Filtek (TM) Z -250 resin presents the best result related to the thermal properties and polymerization after light curing among the other resins.

Electrical transport mechanisms and structure of hydrogenated and non-hydrogenated nanocrystalline Ga1-xMnxAs films

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Biogenic habitat structure provided by temperate macroalgae change along a latitudinal gradient in ocean climate

[EN] Global warming is affecting all major ecosystems, including temperate reefs where canopy-forming seaweeds provide biogenic habitat. In contrast to the rapidly growing recognition of how climate affects the performance and distribution of individuals and populations, relatively little is known about possible links between climate and biogenic habitat structure. We examined the relationship between several ocean temperature characteristics, expressed on time-scales of days, months and years, on habitat patch characteristics on 24 subtidal temperate reefs along a latitudinal gradient (Western Australia; ca 34 to 27º S). Significant climate related variation in habitat structure was observed, even though the landscape cover of kelp and fucalean canopies did not change across the climate gradient: monospecific patches of kelp became increasingly dominant in warmer climates, at the expense of mixed kelp-fucalean canopies. The decline in mixed canopies was associated with an increase in the abundance of Sargassum spp., replacing a more diverse canopy assemblage of Scytothalia doryocarpa and several other large fucoids. There were no observed differences in the proportion of open gaps or gap characteristics. These habitat changes were closely related to patterns in minimum temperatures and temperature thresholds (days > 20 °C), presumably because temperate algae require cool periods for successful reproduction and recruitment (even if the adults can survive warmer temperatures). Although the observed habitat variation may appear subtle, similar structural differences have been linked to a range of effects on canopy-associated organisms through the provision of habitat and ecosystem engineering. Consequently, our study suggests that the magnitude of projected temperature increase is likely to cause changes in habitat structure and thereby indirectly affect numerous habitat-dependent plants and animals

3D printed sensing patches with embedded polymer optical fibre Bragg gratings

The first demonstration of a polymer optical fibre Bragg grating (POFBG) embedded in a 3-D printed structure is reported. Its cyclic strain performance and temperature characteristics are examined and discussed. The sensing patch has a repeatable strain sensitivity of 0.38 pm/μepsilon. Its temperature behaviour is unstable, with temperature sensitivity values varying between 30-40 pm/°C.

Embedding silica and polymer fibre Bragg gratings (FBG) in plastic 3D-printed sensing patches

This paper reports the first demonstration of a silica fibre Bragg grating (SOFBG) embedded in an FDM 3-D printed housing to yield a dual grating temperature-compensated strain sensor. We also report the first ever integration of polymer fibre Bragg grating (POFBG) within a 3-D printed sensing patch for strain or temperature sensing. The cyclic strain performance and temperature characteristics of both devices are examined and discussed. The strain sensitivities of the sensing patches were 0.40 and 0.95 pm/μϵ for SOFBG embedded in ABS, 0.38 pm/μμ for POFBG in PLA, and 0.15 pm/μμ for POFBG in ABS. The strain response was linear above a threshold and repeatable. The temperature sensitivity of the SOFBG sensing patch was found to be up to 169 pm/°C, which was up to 17 times higher than for an unembedded silica grating. Unstable temperature response POFBG embedded in PLA was reported, with temperature sensitivity values varying between 30 and 40 pm/°C.

The role of soil characteristics on temperature sensitivity of soil organic matter

The uncertainty associated with how projected climate change will affect global C cycling could have a large impact on predictions of soil C stocks. The purpose of our study was to determine how various soil decomposition and chemistry characteristics relate to soil organic matter (SOM) temperature sensitivity. We accomplished this objective using long-term soil incubations at three temperatures (15, 25, and 35°C) and pyrolysis molecular beam mass spectrometry (py-MBMS) on 12 soils from 6 sites along a mean annual temperature (MAT) gradient (2–25.6°C). The Q10 values calculated from the CO2 respired during a long-term incubation using the Q10-q method showed decomposition of the more resistant fraction to be more temperature sensitive with a Q10-q of 1.95 ± 0.08 for the labile fraction and a Q10-q of 3.33 ± 0.04 for the more resistant fraction. We compared the fit of soil respiration data using a two-pool model (active and slow) with first-order kinetics with a three-pool model and found that the two and three-pool models statistically fit the data equally well. The three-pool model changed the size and rate constant for the more resistant pool. The size of the active pool in these soils, calculated using the two-pool model, increased with incubation temperature and ranged from 0.1 to 14.0% of initial soil organic C. Sites with an intermediate MAT and lowest C/N ratio had the largest active pool. Pyrolysis molecular beam mass spectrometry showed declines in carbohydrates with conversion from grassland to wheat cultivation and a greater amount of protected carbohydrates in allophanic soils which may have lead to differences found between the total amount of CO2 respired, the size of the active pool, and the Q10-q values of the soils.

The high temperature mechanical characteristics of superplastic 3 mol% yttria stabilized zirconia

A detailed study was undertaken to characterize the deformation behavior of a superplastic 3 mol% yttria-stabilized tetragonal zirconia (3YTZ) over a wide range of strain rates, temperatures and grain sizes. The experimental data were analyzed in terms of the following equation for high temperature deformation: Image Full-size image ∞ σn d−pexp(−Q/RT), where Image Full-size image is the strain rate, σ is the flow stress, d is the grain size, Q is the activation energy, R is the gas constant, T is the absolute temperature, and n and p are constants termed the stress exponent and the inverse grain size exponent, respectively. The experimental data over a wide range of stresses revealed a transition in stress exponent. Deformation in the low and high stress regions was associated with n not, vert, similar 3 and p not, vert, similar 1, and n not, vert, similar 2 and p not, vert, similar 3, respectively. The transition stress between the two regions decreased with increasing grain size. The activation energy was similar for both regions with a value of not, vert, similar 550 kJ mol−1. Microstructural measurements revealed that grains remained essentially equiaxed after the accumulation of large strains, and very limited concurrent grain growths occurred in most experiments. Assessment of possible rate controlling creep mechanisms and comparison with previous studied indicate that in the n not, vert, similar 2 region, deformation occurs by a grain boundary sliding process whose rate is independent of impurity content. Deformation in the n not, vert, similar 3 region is controlled by an interface reaction that is highly sensitive to impurity content. It is concluded that an increase in impurity content increases yttrium segregation to grain boundaries, which enhances the rate of the interface reaction, thereby decreasing the apparent transition stress between the n not, vert, similar 2 and n not, vert, similar 3 regions. This unified approach incorporating two sequential mechanisms can rationalize many of the apparently dissimilar results that have been reported previously for deformation of 3YTZ.