Lehiaketa motor baten atzealde-suspentsio sistema doigarri baten elementuen diseinua

[EU]Proiektu hau lehiaketa motor baten atzealde-suspentsio sistema doigarri baten elementuen diseinuan datza. Luzeran erregulagarria izango den tirantea eta suspentsio triangelua diseinatu eta optimizatuko dira. Diseinuak ahalik eta pisu txikiena izatea ahalbidetzen duten makinen elementuak (errotulak eta errodamenduak) aukeratuko dira. Lanaren garapenerako Motostudent izeneko lehiaketatik hartutako datu errealak erabiliko dira. Suspentsio sistemaren diseinua Creo2.0 (lehengo Pro-Engineer) software-arekin egingo da. Bestalde, beste software batzuk ere erabiliko dira, hala nola, Working Model 2D eta ANSYS, sistemaren analisia errazteko.

地震力对高架桥梁上轨道车辆的动态分析与安全性研究

The stability and derailment behavior analysis of railway vehicle system has been discussed by many papers in the past. In stability, give first place to consider hunting behavior of vehicle, therefore most of papers was only consider lateral and yaw motion, but vertical motion is the important factor in derailment behavior, and it will be quite effect in stability. We will probe the running stability and derailment behavior of railway vehicle moving on the viaduct in this paper. In this paper, we use Nadal’s formula to get the derailment quotient. In this paper, the railway vehicle is considered to be three subsystems, carbody, bogie and wheelset. There are secondary suspension systems between carbody and bogies, and primary suspension systems connecting bogies and wheelsets. A vehicle with vertical, lateral, roll, and yaw directions motion is considered to derive the mathematical equations. A vehicle with three-dimensional model has 16 degrees of freedom is used to develop the equations of train motion. In this study, results show that the track shift force and derailment factor increase with an increase of ground acceleration. But for the track shift force and derailment factor, the effects of track irregularities and train speed are very small. Key words: earthquake, railway vehicle, viaduct, derailment factor.

Projecto suspensão formula student

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia Mecânica

Estudo de caso de malformação congénita, com quantificação do êmbolo em 4 sistemas de suspensão para próteses endosqueléticas transtibiais com encaixe TSB

Introdução – O efeito de êmbolo é um dos principais problemas relacionados com a eficácia de uma prótese. Uma diminuição do mesmo pode levar a uma marcha mais natural através do aumento da propriocetividade. Objetivos – Verificar se existe diferença de valores do efeito de êmbolo entre vários sistemas de suspensão para próteses transtibiais com a utilização de Liners e testar a aplicação de testes de imagiologia na análise da melhor solução protésica para um determinado indivíduo. Metodologia – Foi obtida uma radiografia da prótese em carga na posição ortostática, mantendo o peso do indivíduo igualmente distribuído pelos dois pés. Seguidamente foi realizada outra radiografia no plano sagital com o joelho com 30° de flexão, com a prótese suspensa e um peso de 5kg aplicado na extremidade distal da mesma durante 30 seg. Através destes dois exames efetuaram-se as medições do êmbolo para cada tipo de sistema de suspensão. Resultados – Dos quatro sistemas estudados apenas três apresentam valores de êmbolo, visto que um dos sistemas não criou suspensão suficiente para suportar o peso colocado na extremidade distal da prótese. Através das medições realizadas nos exames imagiológicos dos três sistemas pudemos encontrar variações de efeito de êmbolo que vão dos 47,91mm aos 72,55mm. Conclusão – Através da realização do estudo imagiológico verificaram-se diferenças a nível do efeito de êmbolo nos vários sistemas de suspensão, provando que esta é uma ferramenta viável na avaliação do mesmo. Também através da análise dos resultados ficou notório que o sistema de suspensão Vacuum Assisted Suspention System (VASS) é o que apresenta menos êmbolo.

An Intelligent Controller Design for Magnetorheological Damper Based on a Quarter-car Model

This paper presents the control strategies of nonlinear vehicle suspension using a magnetorheological (MR) damper. We used two different approaches for modeling and control of the mechanical and electrical parts of the suspension systems with the MR damper. First, we have formulated and resolved the control problem in order to design the linear feedback dumping force controller for a nonlinear suspension system. Then the values of the control dumping force functions were transformed into electrical control signals by the application of a fuzzy logic control method. The numerical simulations were provided in order to show the effectiveness of this method for the semi-active control of the quarter-car suspension.

Projetos de controladores baseados em LMI usando realimentação da derivada dos estados

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Dimensionamento de suspensões veiculares para isolamento de vibrações excitadas pela via

This work intends to perform the dimensioning of the Guaratinguetá’s Engineering College Baja SAE vehicle suspension system. To do so, concepts of suspension systems, human comfort limits to vibrations and automotive models for suspension vibration analyses are reviewed. On the development of this work descriptions of considerations specific for the vehicle object of this work are made as well as descriptions of the experiment made to determine the stiffness of the tire used. These concepts are applied through a computational routine that allows the dimensioning of springs and shock absorbers of both front and rear axles of a vehicle in a way to respect all the criteria showed during this work and visualize the system’s behavior when excited on different frequencies

Caracterização térmica e físico-química do sistema argila-8-hidroxiquinolina na remoção de íons Fe(III), Ni(II) e Co(II)

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Contribution of electrical parameters on the dynamical behaviour of a nonlinear electromagnetic damper

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Influência das não linearidades geométricas em sistemas de suspensão com amortecimento assimétrico sob excitação harmônica

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Whole-body vibration exposure study in U.S. railroad locomotives--an ergonomic risk assessment

Whole-body vibration exposure of locomotive engineers and the vibration attenuation of seats in 22 U.S. locomotives (built between 1959 and 2000) was studied during normal revenue service and following international measurement guidelines. Triaxial vibration measurements (duration mean 155 min, range 84-383 min) on the seat and on the floor were compared. In addition to the basic vibration evaluation (aw rms), the vector sum (av), the maximum transient vibration value (MTVV/aw), the vibration dose value (VDV/(aw T1/4)), and the vibration seat effective transmissibility factor (SEAT) were calculated. The power spectral densities are also reported. The mean basic vibration level (aw rms) was for the fore-aft axis x = 0.18 m/sec2, the lateral axis y = 0.28 m/sec2, and the vertical axis z = 0.32 m/sec2. The mean vector sum was 0.59 m/sec2 (range 0.27 to 1.44). The crest factors were generally at or above 9 in the horizontal and vertical axis. The mean MTVV/aw was 5.3 (x), 5.1 (y), and 4.8 (z), and the VDV/(aw T1/4) values ranged from 1.32 to 2.3 (x-axis), 1.33 to 1.7 (y-axis), and 1.38 to 1.86 (z-axis), generally indicating high levels of shocks. The mean seat transmissibility factor (SEAT) was 1.4 (x) and 1.2 (y) and 1 (z), demonstrating a general ineffectiveness of any of the seat suspension systems. In conclusion, these data indicate that locomotive rides are characterized by relatively high shock content (acceleration peaks) of the vibration signal in all directions. Locomotive vertical and lateral vibrations are similar, which appears to be characteristic for rail vehicles compared with many road/off-road vehicles. Tested locomotive cab seats currently in use (new or old) appear inadequate to reduce potentially harmful vibration and shocks transmitted to the seated operator, and older seats particularly lack basic ergonomic features regarding adjustability and postural support.

Dynamic Response Optimization of Vehicles through Efficient Multibody Formulations and Automatic Differentiation Techniques

El diseño y desarrollo de sistemas de suspensión para vehículos se basa cada día más en el diseño por ordenador y en herramientas de análisis por ordenador, las cuales permiten anticipar problemas y resolverlos por adelantado. El comportamiento y las características dinámicas se calculan con precisión, bajo coste, y recursos y tiempos de cálculo reducidos. Sin embargo, existe una componente iterativa en el proceso, que requiere la definición manual de diseños a través de técnicas “prueba y error”. Esta Tesis da un paso hacia el desarrollo de un entorno de simulación eficiente capaz de simular, analizar y evaluar diseños de suspensiones vehiculares, y de mejorarlos hacia la solución optima mediante la modificación de los parámetros de diseño. La modelización mediante sistemas multicuerpo se utiliza aquí para desarrollar un modelo de autocar con 18 grados de libertad, de manera detallada y eficiente. La geometría y demás características de la suspensión se ajustan a las del vehículo real, así como los demás parámetros del modelo. Para simular la dinámica vehicular, se utiliza una formulación multicuerpo moderna y eficiente basada en las ecuaciones de Maggi, a la que se ha incorporado un visor 3D. Así, se consigue simular maniobras vehiculares en tiempos inferiores al tiempo real. Una vez que la dinámica está disponible, los análisis de sensibilidad son cruciales para una optimización robusta y eficiente. Para ello, se presenta una técnica matemática que permite derivar las variables dinámicas dentro de la formulación, de forma algorítmica, general, con la precisión de la maquina, y razonablemente eficiente: la diferenciación automática. Este método propaga las derivadas con respecto a las variables de diseño a través del código informático y con poca intervención del usuario. En contraste con otros enfoques en la bibliografía, generalmente particulares y limitados, se realiza una comparación de librerías, se desarrolla una formulación híbrida directa-automática para el cálculo de sensibilidades, y se presentan varios ejemplos reales. Finalmente, se lleva a cabo la optimización de la respuesta dinámica del vehículo citado. Se analizan cuatro tipos distintos de optimización: identificación de parámetros, optimización de la maniobrabilidad, optimización del confort y optimización multi-objetivo, todos ellos aplicados al diseño del autocar. Además de resultados analíticos y gráficos, se incluyen algunas consideraciones acerca de la eficiencia. En resumen, se mejora el comportamiento dinámico de vehículos por medio de modelos multicuerpo y de técnicas de diferenciación automática y optimización avanzadas, posibilitando un ajuste automático, preciso y eficiente de los parámetros de diseño. ABSTRACT Each day, the design and development of vehicle suspension systems relies more on computer-aided design and computer-aided engineering tools, which allow anticipating the problems and solving them ahead of time. Dynamic behavior and characteristics are thus simulated accurately and inexpensively with moderate computational times and resources. There is, however, an iterative component in the process, which involves the manual definition of designs in a trialand-error manner. This Thesis takes a step towards the development of an efficient simulation framework capable of simulating, analyzing and evaluating vehicle suspension designs, and automatically improving them by varying the design parameters towards the optimal solution. The multibody systems approach is hereby used to model a three-dimensional 18-degrees-of-freedom coach in a comprehensive yet efficient way. The suspension geometry and characteristics resemble the ones from the real vehicle, as do the rest of vehicle parameters. In order to simulate vehicle dynamics, an efficient, state-of-the-art multibody formulation based on Maggi’s equations is employed, and a three-dimensional graphics viewer is developed. As a result, vehicle maneuvers can be simulated faster than real-time. Once the dynamics are ready, a sensitivity analysis is crucial for a robust optimization. To that end, a mathematical technique is introduced, which allows differentiating the dynamic variables within the multibody formulation in a general, algorithmic, accurate to machine precision, and reasonably efficient way: automatic differentiation. This method propagates the derivatives with respect to the design parameters throughout the computer code, with little user interaction. In contrast with other attempts in the literature, mostly not generalpurpose, a benchmarking of libraries is carried out, a hybrid direct-automatic differentiation approach for the computation of sensitivities is developed, and several real-life examples are analyzed. Finally, a design optimization process of the aforementioned vehicle is carried out. Four different types of dynamic response optimization are presented: parameter identification, handling optimization, ride comfort optimization and multi-objective optimization; all of which are applied to the design of the coach example. Together with analytical and visual proof of the results, efficiency considerations are made. In summary, the dynamic behavior of vehicles is improved by using the multibody systems approach, along with advanced differentiation and optimization techniques, enabling an automatic, accurate and efficient tuning of design parameters.

Development of vehicles-in-use sub-limit maneuvers. Volume II: technical report. Final report.

National Highway Traffic Safety Administration, Crash Avoidance Research Division, Washington, D.C.

Improved hybrid computer vehicle handling program. Final report.

National Highway Traffic Safety Administration, Washington, D.C.

Response of asphalt concrete pavements to dynamic truck loads. Final report.

California Department of Transportation, Sacramento