Single mode performance of a single mode injected locked quantum dot laser

An injection locked QD laser is demonstrated to provide single longitudinal mode operation with a 40dB SMSR and an improvement in RIN peak from 1.3-2.3GHz. Alpha factor is measured to be 0.8. © 2005 Optical Society of America.

Single mode performance of a single mode injected locked quantum dot laser

An injection locked QD laser is demonstrated to provide single longitudinal mode operation with a 40dB SMSR and an improvement in RIN peak from 1.3-2.3GHz. Alpha factor is measured to be 0.8. © 2005 Optical Society of America.

Single mode operation of a Fabry-Perot laser locked by a tunable laser

In this article, the single mode operation of a Fabry-Perot laser (FP-LD) subject to the optical injection from a tunable laser is investigated. The maximum side mode suppression ratio (SMSR) is 53 dB, and the locked wavelength range is about 46 nm, which can cover 58 International Telecommunication Union (ITU) wavelengths with 100 GHz spacing or 115 ITU wavelengths with 50 GHz spacing for wavelength division multiplexing (WDM) system. In the wavelength range front 1535 to 1569 nm, the SMSR is over 46 dB, and the frequency response of the injection-locked FP-LD can be improved with the proper wavelength detuning. (c) 2008 Wiley Periodicals, Inc.

Design of high polarization and single-mode photonic crystal laser

The dipole mode in triangular photonic crystal single defect cavity is degenerate. By deforming the lattice in photonic crystal we can obtain non-degenerate dipole modes. Lattice deforming in the whole photonic crystal destroys the characteristic of symmetry, so the distribution of the electromagnetic field is affected and the polarization of the electromagnetic field is also changed. Lattice deforming divides the degenerate dipole mode into the x-dipole mode and the y-dipole mode. It is found that the non-degenerate modes have better properties of polarization. So the high polarization and single dipole mode photonic crystal laser can be achieved by deforming the lattice of photonic crystal. In this paper, we simulated the cavity in photonic crystal slab and mainly calculated the quality factor of x-dipole mode under different deforming conditions and with different filling factors. The properties of polarization of x-dipole and y-dipole modes are also calculated. It is found that the ratio of intensities of E-x to E-y in x-dipole mode and that of E-y to E-x in y-dipole mode are 44 and 27, respectively.

Single mode vertical-cavity surface emitting laser with surface plasmon nanostructure

The vertical-cavity surface-emitting laser(VCSEL) has proved to be a low cost light source with attractive properties such as surface emission, circular and low divergence output beam, and simple integration in two-dimensional array. Many new applications such as in spectroscopy, optical storage, short distance fiber optic interconnects, and in longer distance communication, are continuously arising. Many of these applications require stable and single-mode high output power. Several methods that affect the transverse guiding and/or introduce mode selective loss or gain have been developed. In this study, a method for improving the single mode output power by using metal surface plasmons nanostructure is proposed. Theoretical calculation shows that the outpout power is improved about 50% compared to the result of standard VCSELs.

Ridge waveguide laser integrated with spot-size converter in a single step epitaxial for high coupling efficiency to single-mode fibres

A 1.55-mum laser diode integrated with a spot-size converter was fabricated in a single step epitaxial by using the conventional photolithography and chemical wet etching process. The device was constructed by a conventional ridge waveguide active layer and a larger passive ridge-waveguide layer. The threshold current was 40 mA together with high slope efficiency of 0.24 W/A. The beam divergence angles in the horizontal and vertical directions were as small as 12.0degrees x 15.0degrees, respectively, resulting in about 3.2-dB coupling losses with a cleaved optical fibre.

Single-mode holey vertical-cavity surface-emitting laser with ultra-narrow beam divergence

We demonstrated oxide-confined 850-nm vertical-cavity surface-emitting lasers (VCSELs) with a two-dimensional petal-shaped holey structure composed of several annular-sector-shaped holes. Four types of devices with different hole numbers were designed and fabricated. The measured results showed that the larger hole number was beneficial to purifying the lasing mode, and realizing the single-mode operation. The side mode suppression ratio (SMSR) exceeded 30 dB throughout the entire drive current. Mode selective loss mechanism was used to explain the single-mode characteristic. The single-mode devices possessed good beam profiles, and the lowest divergence angle was as narrow as 3.2 degrees (full width at half maximum), attributed to the graded index profile and the shallow etching in the top distributed Bragg reflector (DBR).

Stable single-mode distributed feedback quantum cascade laser with surface metal grating

A design of single-mode distributed feedback quantum cascade lasers (DFB-QCLs) with surface metal grating is described. A rigorous modal expansion theory is adopted to analyse the interaction between the waveguide mode and the surface plasmon wave for different grating parameters. A stable single-mode operation can be obtained in a wide range of grating depths and duty cycles. The single-mode operation of surface metal grating DFB-QCLs at room temperature for lambda = 8.5 mu m is demonstrated. The device shows a side-mode suppression ratio of above 20 dB. A linear tuning of wavelength with temperature indicates the stable single-mode operation without mode hopping.

Eye-safe, high-energy, single-mode all-fiber laser with widely tunable repetition rate

We present a novel high-energy, single-mode, all-fiber-based master-oscillator-power-amplifier (MOPA) laser system operating in the C-band with 3.3-ns pulses and a very widely tunable repetition rate, ranging from 30 kHz to 50 MHz. The laser with a maximum pulse energy of 25 mu J and a repetition rate of 30 kHz is obtained at, a wavelength of 1548 nm by using a double-clad, single-mode, Er:Yb co-doped fiber power amplifier.

Design of a Tapered Lens for Semiconductor Laser to Single-Mode Fiber Coupling

The theoretical investigation of the coupling efficiency of a laser diode to a single mode fiber via a hemispherical lens on the tip of the tapered fiber in the presence of possible transverse offset and angular mismatch is reported.Without the misalignment,coupling efficiency increases with the decreasing of taper length.With the misalignment,this relation is that the coupling efficiency decreases with each kind of offset.

A Single Mode 980nm InGaAs/GaAs/AlGaAs Large Optical Cavity Quantum Well Laser with Low Vertical Divergence Angle

To achieve high optical power as well as low vertical divergence angle, a new kind of optimized large optical cavity (LOC) structure is applied to a ridge waveguide 980nm InGaAs/GaAs/AlGaAs multi-quantum well laser. The optical power density in the waveguide is successfully reduced. The maximum output power is more than 400mW with a slope efficiency of 0.89W/A and the far-field vertical divergence angle is lowered to 23°.

The study of single mode 650nm AlGaInP quantum well laser diodes for DVD

Single mode 650nm AlGaInP quantum well laser diodes grown by low pressure metal organic chemical vapor deposition (LP-MOCVD) was reported in this paper. Selected buried rigewaveguid were applied for single mode operation especially for DVD use. The operating temperature over 90 degree at CW output power 5 mW was achieved.

Measurement of single mode imprint in laser ablative drive of a thin Al foil by extreme ultraviolet laser radiography

The temporal development of laser driven single mode perturbations in thin A1 foils has been measured using extreme ultraviolet (XUV) laser radiography. 15, 30, 70 and 90 mu m single modes were imprinted on 2 mu m thick A1 foils with an optical driver laser at 527 nm for intensities in the range 5 x 10(12) to 1.5 x 10(13) W cm(-2). The magnitude of the imprinted perturbation at the time of shock break out was determined by fitting to the data estimated curves of growth of the Rayleigh-Taylor instability after shock break out. The efficiency of imprinting is independent of perturbation wavelength in the parameter range of this experiment, suggesting little influence of thermal conduction smoothing. The results are of interest for directly driven inertially confined fusion. (C) 1998 American Institute of Physics.

Spectral narrowing of negatively chirped femtosecond pulse by cross-phase modulation in a single-mode optical fiber

We demonstrate theoretically that the negatively chirped femtosecond laser pulse can be spectrally narrowed by cross-phase modulation. The new view is well Supported by numerical simulation. The negative chirp method in fibers might be useful in all optical wavelength switching applications. (c) 2005 Elsevier B.V. All rights reserved.