Chromatic reintegration of historical mortars with lime-based pozzolanic consolidant products

3rd Historic Mortars Conference, 11-14 September 2013, Glasgow, Scotland

Evaluation of Pozzolanic Reactivity of Artificial Pozzolans

Materials Science Forum Vols. 730-732 (2013) pp 433-438

The influence of use additives on nitrous oxide emission during swine slurry composting.

use of additives (Mg/P and nitrification inhibitor dicyandiamide - DCD), on nitrous oxide emission during swine slurry composting. The experiment was run in duplicate; the gas was monitored for 30 days in different treatments (control, DCD, Mg/P and DCD + Mg/P). Nitrous oxide emissions rate (mg of N2O-N.day-1) and the accumulated emissions were calculated to compare the treatments. Results has shown that emissions of N-N2O were reduced by approximately 70, 46 and 96% through the additions of DCD, MgCl2.6H2O + H3PO4 and both additives, respectively, compared to the control. Keywords Composting; swine slurry; additives; nitrous

Consolidation and chromatic reintegration of historical renders with lime-based pozzolanic products

Historical renders are exposed to several degradation processes that can lead to a wide range of anomalies,such as scaling, detachments, and pulverization. Among the common anomalies, the loss of cohesion and of adhesion are usually identified as the most difficult to repair; these anomalies still need to be deeply studied to design compatible, durable, and sustainable conservation treatments. The restitution of render cohesion can be achieved using consolidating products. Nevertheless, repair treatments could induce aesthetic alterations, and, therefore, are usually followed by chromatic reintegration. This work aims to study the effectiveness of mineral products as consolidants for lime-based mortars and simultaneously as chromatic treatments for pigmented renders. The studied consolidating products are prepared by mixing air lime,metakaolin, water, and mineral pigments. The idea of these consolidating and coloring products rises from a traditional lime-based technique, the limewash, widely diffused in southern Europe and in the Mediterranean area. Consolidating products were applied and tested on lime-based mortar specimens with a low binder–aggregate ratio and therefore with reduced cohesion. A physico-mechanical, microstructural, and mineralogical characterization was performed on untreated and treated specimens, in order to evaluate the efficacy and durability of the treatments. Accelerated aging tests were also performed to assess consolidant durability, when subjected to aggressive conditions. Results showed that the consolidants tested are compatible, effective, and possess good durability.

Production and extraction of polysaccharides and oligosaccharides and their use as new food additives

Polysaccharides and oligosaccharides can improve quality and enhance nutritional value of final food products due to their technological and nutritional features ranging from their capacity to improve texture to their effect as dietary fibers. For this reason, they are among the most studied ingredients in the food industry. The use of natural polysaccharides and oligosaccharides as food additives has been a reality since the food industry understood their potential technological and nutritional applications. Currently, the replacement of traditional ingredients and/or the synergy between traditional ingredients and polysaccharides and oligosaccharides are perceived as promising approaches by the food industry. Traditionally, polysaccharides have been used as thickening, emulsifying, and stabilizing agents, however, at this moment polysaccharides and oligosaccharides claim health and nutritional advantages, thus opening a new market of nutritional and functional foods. Indeed, their use as nutritional food ingredients enabled the food industry to develop a countless number of applications, e.g., fat replacers, prebiotics, dietary fiber, and antiulcer agents. Based on this, among the scientific community and food industry, in the last years many research studies and commercial products showed the possibility of using either new or already used sources (though with changed properties) of polysaccharides for the production of food additives with new and enhanced properties. The increasing interest in such products is clearly illustrated by the market figures and consumption trends. As an example, the sole market of hydrocolloids is estimated to reach $7 billion in 2018. Moreover, oligosaccharides can be found in more than 500 food products resulting in a significant daily consumption. A recent study from the Transparency Market Research on Prebiotic Ingredients Market reported that prebiotics' demand was worth $2.3 billion in 2012 and it is estimated to reach $4.5 billion in 2018, growing at a compound annual growth rate of 11.4% between 2012 and 2018. The entrance of this new generation of food additives in the market, often claiming health and nutritional benefits, imposes an impartial analysis by the legal authorities regarding the accomplishment of requirements that have been established for introducing novel ingredients/food, including new poly- and oligosaccharides. This chapter deals with the potential use of polysaccharides and oligosaccharides as food additives, as well as alternative sources of these compounds and their possible applications in food products. Moreover, the regulation process to introduce novel polysaccharides and oligosaccharides in the market as food additives and to assign them health claims is discussed.

Fotoestabilidad de compuestos fenólicos. Evaluación de su potencial capacidad como aditivos antioxidantes. Photostability of phenolic compounds. Assessment of their potential antioxidant activity as additives.

La autooxidación es la forma de deterioro de los productos grasos más importante después de las alteraciones producidas por microorganismos, lo que representa un tema de gran interés económico para las industrias alimenticia y cosmética, ya que da lugar a la aparición de sabores y olores desagradables lo que hace que estos productos sean inaceptables para el consumidor o que reduzcan su vida útil. Dicho proceso se inicia a partir de la reacción de ácidos grasos con oxígeno y puede ser desencadenado por la exposición del producto graso a la luz medioambiental. En estos casos ocurre un proceso de fotooxidación sensibilizada, con la participación de especies reactivas de oxígeno (ROS). Por esta razón, la preservación de producto graso al efecto de las ROS es un punto de capital importancia. Las industrias intentan evitar la oxidación de los productos grasos mediante diferentes técnicas, como el envasado al vacío o en recipientes opacos, pero también utilizando antioxidantes agregados ex-profeso. En particular, los fenoles son secuestradores no enzimáticos de ROS y radicales libres. Actúan como antioxidantes secundarios o interruptores de la cadena oxidativa de lípidos, desactivando las especies reactivas en sus etapas iniciales y evitando que el proceso oxidativo continúe. Por tal motivo, para el presente Proyecto hemos escogido, como potenciales antioxidantes, dos fenoles estructuralmente relacionados con el hidroxitirosol-un antioxidante natural del aceite de oliva-. A través de reacciones fotosensibilizadas, mediante un estudio cinético, mecanístico, de relaciones estructura-reactividad y de dilucidación de fotoproductos se intentará obtener la información que satisface los objetivos específicos de este Proyecto, a saber: a) la resistencia de dHT frente a la oxidación fotopromovida, y en particular a los procesos fotosensibilizados; b) la propensión de dHT para generar especies oxidantes ya sea por irradiación directa o por interacciones específicas con estados excitados de otras moléculas; c) la influencia del medio sobre la capacidad antioxidante de dHT; d) el establecimiento de relaciones estructura-reactividad en lo referida a la actividad antioxidante de dHT. Se trabajará con distintos tipos de sensibilizadores como generadores de diferentes ROS. Para establecer y dilucidar los aspectos cinéticos y mecanísticos mencionados es necesario obtenerinformación acerca de las constantes cinéticas de los diferentes procesos involucrados. La estrategia de trabajo consistirá en abordar condiciones experimentales tales que inhiban determinadas reacciones competitivas y permitan el desarrollo de otras. Se espera que el conocimiento que se genere a partir de los resultados del presente Proyecto, constituya un importante aporte para el diseño y desarrollo de nuevos antioxidantes liposolubles que posean exacerbadas sus propiedades como fotoprotectores frente a eventuales oxidaciones a las que pueda estar expuesto un producto graso.

Occurrence and bioaccumulation study of PCDD and PCDF from mineral feed additives

Occurrence of polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) was evaluated in sepiolite as a widely employed binder and anti-caking agent for animal feed. Also, naturally contaminated kaolinitic clay was used for comparative purposes. Since sepiolite shows remarkable adsorption properties, particular interest was paid to the extraction steps as they become critical for the final determination of these pollutants in such matrixes. Furthermore, classical Soxhlet extraction using different extracting strategies as well as acid treatment were carried out with simultaneous liquid-liquid extraction. Results obtained depended on the extraction procedure applied. Acid treatment or Soxhlet extraction using a mixture of toluene:ethanol as solvent allowed to reach the minimum requirements of recovery rates. However, Soxhlet extraction using a mixture cyclohexane:toluene as extracting solvent did not allow to comply with minimum specifications for recovery. Significant differences were obtained in TEQ units when acid treatment was applied in comparison to Soxhlet extraction. This fact can be explained because the use of drastic acid conditions allows removing strongly adsorbed analytes which can be uniquely extracted after a total destruction of the crystalline structure of sepiolite. On the contrary, Soxhlet extraction was not able to destroy the structure of sepiolite and as a consequence the PCDDs/Fs were strongly adsorbed in the internal structure of the mineral. From biological point of view the availability of these toxicants constitutes a critical aspect playing an important role in the final decision choosing particular analytical procedures. Then, acid conditions in the digestive tract should be taken into account. In this scenario, a bioaccumulation study was conducted to evaluate the transference of PCDDs/PCDFs from the sepiolite into the animal tissues when fed with feed containing sepiolite. To this end, chickens were used as a model to examine the bioavailability of PCDDs/PCDFs. Four groups of chickens were exposed through their diet to a control feed, feed with 3% w/w sepiolite as additive, feed contaminated with PCDDs/PCDFs at concentration around 2.8 pg WHO-TEQ/g and feed with 2% of a contaminated kaolinitic clay (460 pg TEQ/g mineral). Livers of the four studied groups were analyzed throughout the exposure period. Results of this trial showed that the performance of broilers was not affected by the presence of dioxins at levels tested, and chickens did not show any abnormal behaviour. Dioxins intentionally added to the diet were absorbed and accumulated in the liver in a significant manner, whereas the PCDDs/Fs from sepiolite were not available for chickens since livers from broilers fed 3% sepiolite presented similar WHO-TEQ values than those from broilers fed control diet.

Additives and Protein-DNA Combinations Modulate the Humoral Immune Response Elicited by a Hepatitis C Virus Core-encoding Plasmid in Mice

Humoral and cellular immune responses are currently induced against hepatitis C virus (HCV) core following vaccination with core-encoding plasmids. However, the anti-core antibody response is frequently weak or transient. In this paper, we evaluated the effect of different additives and DNA-protein combinations on the anti-core antibody response. BALB/c mice were intramuscularly injected with an expression plasmid (pIDKCo), encoding a C-terminal truncated variant of the HCV core protein, alone or combined with CaCl2, PEG 6000, Freund's adjuvant, sonicated calf thymus DNA and a recombinant core protein (Co.120). Mixture of pIDKCo with PEG 6000 and Freund's adjuvant accelerated the development of the anti-core Ab response. Combination with PEG 6000 also induced a bias to IgG2a subclass predominance among anti-core antibodies. The kinetics, IgG2a/IgG1 ratio and epitope specificity of the anti-core antibody response elicited by Co.120 alone or combined with pIDKCo was different regarding that induced by the pIDKCo alone. Our data indicate that the antibody response induced following DNA immunization can be modified by formulation strategies.

Beneficial Effects of Selected Additives on Asphalt Cement Mixes, HR-278, 1987

Effects of polyolefins, neoprene, styrene-butadiene-styrene (SBS) block copolymers, styrene-butadiene rubber (SBR) latex, and hydrated lime on two asphalt cements were evaluated. Physical and chemical tests were performed on a total of 16 binder blends. Asphalt concrete mixes were prepared and tested with these modified binders and two aggregates (crushed limestone and gravel), each at three asphalt content levels. Properties evaluated on the modified binders (original and thin-film oven aged) included: viscosity at 25 deg C, 60 deg C and 135 deg C with capillary tube and cone-plate viscometer, penetration at 5 deg C and 25 deg C, softening point, force ductility, and elastic recovery at 10 deg C, dropping ball test, tensile strength, and toughness and tenacity tests at 25 deg C. From these the penetration index, the viscosity-temperature susceptibility, the penetration-viscosity number, the critical low-temperature, long loading-time stiffness, and the cracking temperature were calculated. In addition, the binders were studied with x-ray diffraction, reflected fluorescence microscopy, and high-performance liquid chromatography techniques. Engineering properties evaluated on the 72 asphalt concrete mixes containing additives included: Marshall stability and flow, Marshall stiffness, voids properties, resilient modulus, indirect tensile strength, permanent deformation (creep), and effects of moisture by vacuum-saturation and Lottman treatments. Pavement sections of varied asphalt concrete thicknesses and containing different additives were compared to control mixes in terms of structural responses and pavement lives for different subgrades. Although all of the additives tested improved at least one aspect of the binder/mixture properties, no additive was found to improve all the relevant binder/mixture properties at the same time. On the basis of overall considerations, the optimum beneficial effects can be expected when the additives are used in conjunction with softer grade asphalts.

Evaluation of Asphalt Stabilizing Additives, HR-542, 1994

Efforts are constantly being put forth by researchers, highway related industries and product suppliers to improve the life and performance of asphalt pavements. As a result of those efforts, a variety of asphalt modifiers have been developed and evaluated in experimental sections over the years. Evaluations of the polymer asphalt modifiers have been done and results were usually compared with conventional sections within each respective project. The research presented in this report is also a comparison of asphalt modifiers with each other as well as a comparison of a modifier with its respective conventional section, when they exist. Several of the modifiers showed some improvements in performance while others did not.

Evaluation of Additives for Extruded Asphalt Curbs, MLR-85-06, 1985

This study investigates the properties imparted to extruded asphalt curb mixes by five different additives. The AC used in these mixes was also tested with various amounts of the additives. All of the additives stiffened the AC as indicated by a reduction of penetration and increased viscosity. Only the powdered asphalts, gilsonite and Witcurb improved the Marshall stability and the indirect tensil strength enough to justify their use in curb mixes.

Preservation of minimally processed 'aurora-1' peaches using additives

'Aurora-1' peaches establishes an interesting alternative as a minimally processed product, due to its characteristics like flavor, color, smell, and also because of its handling resistance. However, it has a short shelf life after a fresh-cut due to enzymatic browning and stone cavity collapse. The main purpose of this research was to test the additive with antioxidant effect to prevent browning in minimally processed 'Aurora-1' peaches. The minimal processing consists of washing, sanitizing, peelings and fruit stone extraction. After that, longitudinal cuts were made to obtain eight segments per fruit. The slices were immersed into the following treatment solutions: control (immersion in 2% ascorbic acid); 2% ascorbic acid + 2% calcium chloride; 1% sodium isoascorbate; 1% citric acid; 1% L-cysteine hydrochloride. The products were placed into rigid polystyrene trays branded MEIWA M-54, covered with 14 µm PVC film (OmnifilmTM) and kept in cold storage at 3ºC ± 2ºC and 65% RH for twelve days, and evaluated each three days. Appraised variables were appearance, soluble solids, titratable acidity, soluble carbohydrates and reducing sugars, total and soluble pectin, ascorbic acid, and peroxidase and polyphenol oxidase enzyme activity. L-cysteine gave to the minimally processed products a shelf life of twelve days, limmited by off-flavor. The treatment with ascorbic acid was efficient to maintainthe ascorbic acid content, with a shelf-life of nine days, limited by enzymatic browning.

Use of new silica fillers as additives for polymers used in packaging of fruit

The objective of this work was to synthesize nanosilicas with different degree of hydrophobicity by the sol-gel method, using tetraethyl orthosilicate as a precursor. For this purpose, 3-aminopropyl triethoxysilane (APS) and 1,1,1,3,3,3 - hexamethyldisilazane (HMDS), were added during synthesis as modifiers. A commercial biopolymer (Hexamoll Dinch, BASF) intended for packaging of apples, was added to the new nanosilicas. The materials obtained were characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, potentiometric titration, porosity, specific surface area and hydrophobicity/hydrophilicity by wetting test. Colorimetry was used to evaluate change in apple pulp color after contact with the different silicas.

Ultrafiltration membranes from waste polyethylene terephthalate and additives: synthesis and characterization

The synthesis and characterization of asymmetric ultrafiltration membranes from recycled polyethylene terephthalate (PET) and polyvinylpyrrolidone (PVP) is reported. PET is currently used in many applications, including the manufacture of bottles and tableware. Monomer extraction from waste PET is expensive, and this process has not yet been successfully demonstrated on a viable scale. Hence, any method to recycle or regenerate PET once it has been used is of significant importance from scientific and environmental research viewpoints. Such a process would be a green alternative due to reduced raw monomer consumption and the additional benefit of reduced manufacturing costs. The membranes described here were prepared by a phase-inversion process, which involved casting a solution containing PET, m-cresol as solvent, and polyethylene glycol (PEG) of different molecular weights as additives. The membranes were characterized in terms of pure water permeability (PWP), molecular weight cut-off (MWCO), and flux and membrane morphology. The results show that the addition of PEG with high molecular weights leads to membranes with higher PWP. The presence of additives affects surface roughness and membrane morphology.