Effect of tibial tray inclination on the femoro-tibial contact pattern of a mobile total knee arthroplasty

Introduction: The posterior inclination of the tibial component is an important factor that can affect the success of total knee arthroplasty. It can reduce the posterior impingement and thus increase the range of flexion, but it may also induce instability in flexion, anterior impingement between the polyethylene of postero-stabilizing knee prosthesis, and anterior conflict with the cortical bone and the stem. Although the problem is identified, there is still a debate on the ideal inclination angle and the surgical technique to avoid an excessive posterior inclination. The aim of this study was to predict the effect of a posterior inclination of the tibial component on the contact pattern on the tibial insert, using a numerical musculoskeletal model of the knee joint. Methods: A 3D finite element model of the knee joint was developed to simulate an active and loaded squat movement after total knee arthroplasty. Flexion was actively controlled by the quadriceps muscle and muscle activations were estimated from EMG data and were synchronized by a feedback algorithm. Two inclinations of the tibial tray were considered: a posterior inclination of 0° or 10°. During the entire range of flexion, the following quantities were calculated: the tibiofemoral and patello-femoral contact force, and the contact pattern on polyethylene insert. The antero-posterior displacement of the contact pattern was also measured. Abaqus 6.7 was used for all analyses. Results: The tibio-femoral and patello-femoral contact forces increased during flexion and reached respectively 4 and 7 BW (bodyweight) at 90° of flexion. They were slightly affected by the inclination of the tibial tray. Without posterior inclination, the contact pattern on the tibial insert remained centered. The contact pressure was lower than 5 MPa below 60° of flexion, but exceeded 20 MPa at 90° of flexion. The posterior inclination displaced the contact point posteriorly by 2 to 4 mm. Conclusion: The inclination of the tibial tray displaced the contactpattern towards the posterior border of the tibial insert. However, even for 10° of inclination, the contact center remained far from the posterior border (12 mm). There was no instability predicted for this movement.

Characterization and drying of caja bagasse (Spondias mombin L.) in a tray dryer using a factorial planning

The caja (Spondias mombin L.) is used in the manufacture of ice-cream, jams, pulps, beverages being also consumed in natura. One of the most important procedures in food conservation is drying, considering that most fresh fruits contain approximately 80% of water. Food drying is used to obtain two basic aspects: (1) the economic factor; in the shipping and handling of the product; (2) at the manipulation; once dried and grinded, the material is rehydrated, at desirable levels, to formulate a new product as in ice cream, jams, yoghurts and drinks and may also be added to pasta, biscuits and other industrialized products. The aim of this study was to investigate the kinetics of caja bagasse drying in a fixed-bed tray dryer, using central composite factorial planning. The following factors were evaluated: temperature (55, 65 and 75 ºC), dryer inlet air velocity (3.2, 4.6 and 6.0 m.s-1) and cake thickness (0.8, 1.2 and 1.6 cm) where the response of the considered variable was caja bagasse moisture content (b.s.) and the results showed that the main effects and their interactions were significant at a 95% confidence level being the best condition obtained at temperature of 75 ºC, velocity of 6.0 m.s-1 and cake thickness of 0.8 cm.

Transmission properties of high barrier coated paperboard packages

High barrier materiaaleilla pyritään pidentämään pakattujen elintarvikkeiden hyllyikää. Barrierin tärkein tehtävä on elintarvikkeen suojaaminen hapelta ja kosteudelta. Alumiinin käyttöä barriermateriaalina pyritään vähentämään korvaamalla alumiini polymeereillä, jotka täyttävät elintarvikkeiden asettamat korkeat säilyvyysvaatimukset. Etyylivinyylialkoholin (EVOH) hapenläpäisevyys on kuivissa olosuhteissa alhaisin kaupallisista muovilaaduista. EVOH tarjoaa myös erinomaisen suojan muita kaasuja, rasvoja, hajuja ja aromeja vastaan ja sitä on helppo prosessoida. Polyamideilla on erinomainen kaasutiiveys sekä hyvä lujuus ja sitkeys. Eri muovilaatuja sekoittamalla voidaan vähentää hapenläpäisyä ja parantaa prosessointia. Polyolefiineja käytetään yleisesti päällystysmateriaaleina, koska ne suojaavat tuotetta erinomaisesti kosteudelta. Hapenläpäisyllä tarkoitetaan hapen kulkeutumista materiaalin läpi joko permeaation kautta tai reikien ja vuotojen läpi. Kaasun permeoitumiseen materiaalin läpi vaikuttavat materiaalin vapaa tilavuus, kiteisyysaste, orientaatio, substituointi, suhteellinen kosteus, lämpötila, barrierkerroksen paksuus, paine-ero ja permeoituvan molekyylin ominaisuudet. Kokeellisessa osassa analysoitiin ja vertailtiin kartonkipohjaisia mehutölkkejä, joissa käytettävät high barrier materiaalit olivat EVOH ja PA. Kartonkipohjaisia alumiinitölkkejä käytettiin referenssinä. Pakkausten hapenläpäisevyysmittauksissa saatiin samasta näytteestä toistettavia tuloksia, vaikka vuotomittauksissa saadut tulokset eivät olleet vertailukelpoisia hapenläpäisytulosten kanssa. Tölkkien valmistus vaikutti oleellisesti pakkausten tiiveysominaisuuksiin. Hapenläpäisy vuotojen ja reikien läpi oli merkittävämpää kuin hapenläpäisy materiaalin läpi. Pakkausten tiiveysominaisuuksia analysoitiin mittaamalla appelsiinimehun askorbiini-happopitoisuus. Askorbiinihapon hajoaminen mitattiin koetölkkeihin pakatusta appelsiinimehusta, ja lämpötilan, valon ja hapen vaikutusta askorbiinihapon hajoamiseen tutkittiin 12 viikon ajan. Lämpötilalla oli suurin vaikutus askorbiinihapon hajoamiseen huolimatta käytetystä pakkausmateriaalista.

Estimating the Price and Demand Development of Some Paperboard Grades

Työn tavoitteena oli luoda malli, jonka avulla voitaisiin ennustaa kartonkituotteiden hinnan ja kysynnän kehitystä. Työssä kerättiin aluksi tietoa kartonkimarkkinoista haastattelujen ja tilastotietojen avulla. Näiden perusteella luotiin malli, joka kuvaa kartonkimarkkinoiden ja -teollisuuden rakennetta. Erityisesti kiinnitettiin huomiota asiakkaiden tilauskäyttäytymiseen, tuotannonohjaukseen sekä hinnan muodostumiseen. Työssä käytettiin ennustemenetelmänä systeemidynamiikkaa. Oleellista oli löytää systeemissä esiintyvät tärkeimmät takaisinkytkennät ja systeemin avainmuuttujat. Kun kaikille mallin muuttujille oli määritetty yhtälöt ja vakioille annettu arvot, voitiin mallia simuloida, ja saada ennusteet halutuille muuttujille. Työssä esitettiin ennusteet kartonkimarkkinoiden tärkeimmille parametreille kahden vuoden päähän. Työssä tarkasteltiin myös, miten muutokset mallin käyttäytymistä säätelevissä muuttujissa vaikuttavat tuloksiin. Jotta pystyttäisiin paremmin selvittämään koko kartonkiteollisuuden dynamiikka, lisätutkimusta tarvittaisiin vielä eri kartonkilajien substituutiomahdollisuuksista ja hintojen riippuvuuksista. Mielenkiintoista olisi myös tietää, miten tuotannon käyttöasteiden muutokset ja hinnan vaihtelut vaikuttavat liiketoiminnan kannattavuuteen valmistajien näkökulmasta.

Drivers and Barriers of Collaboration in the Value Chain of Paperboard-Packed Consumer Goods

Value chain collaboration has been a prevailing topic for research, and there is a constantly growing interest in developing collaborative models for improved efficiency in logistics. One area of collaboration is demand information management, which enables improved visibility and decrease of inventories in the value chain. Outsourcing of non-core competencies has changed the nature of collaboration from intra-enterprise to cross-enterprise activity, and this together with increasing competition in the globalizing markets have created a need for methods and tools for collaborative work. The retailer part in the value chain of consumer packaged goods (CPG) has been studied relatively widely, proven models have been defined, and there exist several best practice collaboration cases. The information and communications technology has developed rapidly, offering efficient solutions and applications to exchange information between value chain partners. However, the majority of CPG industry still works with traditional business models and practices. This concerns especially companies operating in the upstream of the CPG value chain. Demand information for consumer packaged goods originates at retailers' counters, based on consumers' buying decisions. As this information does not get transferred along the value chain towards the upstream parties, each player needs to optimize their part, causing safety margins for inventories and speculation in purchasing decisions. The safety margins increase with each player, resulting in a phenomenon known as the bullwhip effect. The further the company is from the original demand information source, the more distorted the information is. This thesis concentrates on the upstream parts of the value chain of consumer packaged goods, and more precisely the packaging value chain. Packaging is becoming a part of the product with informative and interactive features, and therefore is not just a cost item needed to protect the product. The upstream part of the CPG value chain is distinctive, as the product changes after each involved party, and therefore the original demand information from the retailers cannot be utilized as such – even if it were transferred seamlessly. The objective of this thesis is to examine the main drivers for collaboration, and barriers causing the moderate adaptation level of collaborative models. Another objective is to define a collaborative demand information management model and test it in a pilot business situation in order to see if the barriers can be eliminated. The empirical part of this thesis contains three parts, all related to the research objective, but involving different target groups, viewpoints and research approaches. The study shows evidence that the main barriers for collaboration are very similar to the barriers in the lower part of the same value chain; lack of trust, lack of business case and lack of senior management commitment. Eliminating one of them – the lack of business case – is not enough to eliminate the two other barriers, as the operational model in this thesis shows. The uncertainty of the future, fear of losing an independent position in purchasing decision making and lack of commitment remain strong enough barriers to prevent the implementation of the proposed collaborative business model. The study proposes a new way of defining the value chain processes: it divides the contracting and planning process into two processes, one managing the commercial parts and the other managing the quantity and specification related issues. This model can reduce the resistance to collaboration, as the commercial part of the contracting process would remain the same as in the traditional model. The quantity/specification-related issues would be managed by the parties with the best capabilities and resources, as well as access to the original demand information. The parties in between would be involved in the planning process as well, as their impact for the next party upstream is significant. The study also highlights the future challenges for companies operating in the CPG value chain. The markets are becoming global, with toughening competition. Also, the technology development will most likely continue with a speed exceeding the adaptation capabilities of the industry. Value chains are also becoming increasingly dynamic, which means shorter and more agile business relationships, and at the same time the predictability of consumer demand is getting more difficult due to shorter product life cycles and trends. These changes will certainly have an effect on companies' operational models, but it is very difficult to estimate when and how the proven methods will gain wide enough adaptation to become standards.

Paperboard cup with a window

Packaging has to fulfill a lot of demands and the main purpose is to be able to protect the foodstuff packed inside. Typically requirements set on packaging materials reflect the consumer needs. Based on the consumer studies the importance of product visibility is considered as an important property among consumers. However, making the package more transparent the actual shelf life of the product might be reduced. It might have an effect on sensitive foods which contain ingredients vulnerable to light and start to deteriorate more rapidly. The aim for this Masters of Science Thesis was to develop a paperboard cup with a plastic window where different kind of fatty/dry foodstuffs could be stored. The main target was to be able to create an instruction manual how this kind of cup with a window had to be produced without decreasing air tightness and other barrier properties of cupboard material used as a base board. The focus in this work was on designing a shape of the window and finding critical limits for the size, shape and location of the window in the final paperboard cup. Windows were made by cutting holes with different sizes and shapes to different places in the cup blank by using a model cutter. For the windows one plastic film type was selected due to its low oxygen and water vapour transmission properties. The window film was attached to the cup blank by using hot bar and laser seaming methods. Cup manufacturing was done at Stora Enso InnoCentre, Imatra. As a result critical limits for the place, size and shape of the window could be found. The sealing method had a significant effect on the tightness of the cups. Windows didn’t decrease the grip stiffness of the cup. The cup itself gave better light protection than the plastic film used in the windows. The bigger the window, the less the cup could protect the possible foodstuff. Bursting strength was lower in the windows compared to the cup material itself. From environmental point of view DSD licence fees have to be paid due to the amount of used plastic.When using bigger windows the ratio of plastic to fibres increase. This would raise the DSD fee. However, the amount of material is overall reduced which lowers the fee.

Kartonkimateriaalien muotoutuvuus vuokien valmistuksessa

Diplomityön tavoitteena oli tutkia erilaisten elintarvikekartonkien muotoutuvuutta prässäämällä valmistettujen vuokien valmistuksessa. Kirjallisuusosassa käsiteltiin mm. kartongin muotoutuvuuteen vaikuttavia ominaisuuksia sekä lämpötilan ja kosteuden vaikutusta muotoutuvuuteen. Lisäksi kirjallisuusosassa käytiin läpi vuokien valmistusprosessi, jossa vuoka-aihiot valmistetaan stanssaamalla ja vuoat prässäämällä. Lopuksi on esitetty vuokien valmistuksessa kartongin muotoutuvuuteen vaikuttavia ajoparametrejä. Kokeellisessa osassa valmistettiin prässäämällä vuokia erilaisista kartonkimateriaaleista. Jokaiselle materiaalille etsittiin sopivat ajoparametrit erilaisissa kosteuspitoisuuksissa ja vertailtiin niiden muotoutuvuutta. Työ sisälsi myös kaksi laminointikoeajoa, jonka tuloksena saatuja materiaaleja verrattiin referenssi vuokakartonkiin. Vuokien todettiin muotoutuvan parhaiten kosteuden ollessa 7 – 9,4 % välillä. Työssä erottui kartongit, jotka muotoutuivat muita paremmin sekä kartongit, jotka muotoutuivat muita huonommin. Näiden muotoutuvuutta pyrittiin selvittämään mitattujen paperiteknisten ominaisuuksien avulla, mutta selvää yksittäistä selittävää ominaisuutta ei löytynyt. Parhaiten muotoutuvuutta kuvasivat kartonkien kuitukoostumukset. Laminoitujen rakenteiden todettiin muotoutuvan vuokakartonkia paremmin. Tähän vaikuttivat laminaattien korkeammat lujuus- ja venymäarvot.

Learning to Understand the Retailers - The New Approach of a Paperboard Manufacturer

The aim of the study is to expand networking between a packaging material manufacturer and retailers in order to develop products which appeal to brand owners and their customers. The in-built targets are to understand the retailer’s role in the value chain, clarify who makes packaging decision of private label products, and canvass the importance of sustainability. The present value chain of the packaging material manufacturer is reviewed first. It is assumed that sustainability could be a common interest, and The Consumer Goods Forum’s “A Global Language for Packaging and Sustainability” report is shortly discussed. The presentation of the most common packaging materials is based on a guide called “Packaging in the Sustainability Agenda: A Guide for Corporate Decision Makers”. The terms manufacturer’s brand and private label are defined. A retail value chain with emphasis on the role of customers as partners is introduced. The study area is the Nordic countries, and the information about Nordic retailers was provided first by desk research. The interviews were made in Finland, Sweden, Norway and Denmark. The study method is qualitative: the intention was to get initial insights, ideas and understandings. The results are compiled under the headings: sustainability, private labels, cooperation and packaging development. Also the reasons for good profitability of private labels are explained. Sustainability or responsibility is a key driver for innovation in the retail sector. Private labels have become brands. The ways of cooperation between a packaging material manufacturer and a retailer could be education and training. Packaging development is of great interest to retailers and they are willing to contribute.

Pressforming of a tray from a pulp sheet

The aim of this thesis work was to verify the possibility to produce tray packages directly from pulp sheets using press forming techniques. The different existing raw materials of pulp, various sources of molded pulp and different methods of production of molded pulp were studied. Nine different raw materials which were used for experimental work were provided by Stora Enso mills, and Stora Enso Research Centre, Imatra, Finland. The laboratory tests were carried out using LUT Adjustable packaging line at Lappeenranta University of Technology. The results prove that long virgin fibres of pine pulp seems to have better formability with high moisture content compared to others. No significant improvements were noticed with conditioned samples, never the less far studies has to be done to find optimal conditions for production. The results indicated the possibility for making pressformed tray from two different pulp qualities (Sunila pulp and Enopine). The method could prove to be beneficiary as the production line could be shortened and investment in board machines could be avoided if the trays were pressed directly from pulp sheets. Also the labour costs would be reduced. However, there is much work to be done before the quality of a tray produced out of a pulp sheet is comparable to a tray produced out of tray board.

Development of mechanical methods for cell-tray propagation and field transplanting of dwarf napiergrass (Pennisetum purpureum Schumach.)

Since dwarf napiergrass (Pennisetum purpureum Schumach.) must be propagated vegetatively due to lack of viable seeds, root splitting and stem cuttings are generally used to obtain true-to-type plant populations. These ordinary methods are laborious and costly, and are the greatest barriers for expanding the cultivation area of this crop. The objectives of this research were to develop nursery production of dwarf napiergrass in cell trays and to compare the efficiency of mechanical versus manual methods for cell-tray propagation and field transplanting. After defoliation of herbage either by a sickle (manually) or hand-mowing machine, every potential aerial tiller bud was cut to a single one for transplanting into cell trays as stem cuttings and placed in a glasshouse over winter. The following June, nursery plants were trimmed to a 25–cm length and transplanted in an experimental field (sandy soil) with 20,000 plants ha^(−1) either by shovel (manually) or Welsh onion planter. Labour time was recorded for each process. The manual defoliation of plants required 44% more labour time for preparing the stem cuttings (0.73 person-min. stemcutting^(−1)) compared to using hand-mowing machinery (0.51 person-min. stem-cutting^(−1)). In contrast, labour time for transplanting required an extra 0.30 person-min. m^(−2) (14%) using the machinery compared to manual transplanting, possibly due to the limited plot size for machinery operation. The transplanting method had no significant effect on plant establishment or plant growth, except for herbage yield 110 days after planting. Defoliation of herbage by machinery, production using a cell-tray nursery and mechanical transplanting reduced the labour intensity of dwarf napiergrass propagation.

Influence of specimen size, tray inclination and air flow rate on the emission of gases from biomass combustion

Experiments of biomass combustion were performed to determine whether specimen size, tray inclination, or combustion air flow rate was the factor that most affects the emission of carbon dioxide, carbon monoxide, and methane. The chosen biomass was Eucalyptus citriodora, a very abundant species in Brazil, utilized in many industrial applications, including combustion for energy generation. Analyses by gas chromatograph and specific online instruments were used to determine the concentrations of the main emitted gases, and the following figures were found for the emission factors: 1400 ± 101 g kg-1 of CO2, 50 ± 13 g kg-1 of CO, and 3.2 ± 0.5 g kg-1 of CH4, which agree with values published in the literature for biomass from the Amazon rainforest. Statistical analysis of the experiments determined that specimen size most significantly affected the emission of gases, especially CO2 and CO. •Statistical analysis to determine effects on emission factors.•CO2, CO, CH4 emission factors determined for combustion of Eucalyptus.•Laboratory results agreed with data for Amazonian biomass combustion in field tests.•Combustion behavior under flaming and smoldering was analyzed. © 2013 Elsevier Ltd.

Effect of the association between the tray and impression techniques on angulated implants using the All-on-Four system

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Recovering Streptococcus mutans over restorations by the tray technique: a randomized clinical study

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Inactivation of Neosartorya fischeri and Paecilomyces variotii on paperboard packaging material by hydrogen peroxide and heat

This study reports on the influence of heat and hydrogen peroxide combination on the inactivation kinetics of two heat resistant molds: Neosartorya fischeri and Paecilomyces variotii. Spores of different ages (1 and 4 months) of these molds were prepared and D-values (the time required at certain temperature/hydrogen peroxide combination to inactivate 90% of the mold ascospores) were determined using thermal death tubes. D-values found for P. variotii ranged from 1.2 to 25.1 s after exposure to different combinations of heat (40 or 60 degrees C) and hydrogen peroxide (35 or 40% w/w) while for N. fischeri they varied from 2.7 to 14.3 s after exposure to the same hydrogen peroxide concentrations and higher temperatures (60 or 70 degrees C). The influence of temperature and hydrogen peroxide concentration on the d-values varied with the genus of mold and their ages. A synergistic effect of heat and hydrogen peroxide in reducing D-values of Paecilomyces variotti and N. fischeri has been observed. In addition to strict control of temperature, time and hydrogen concentration, hygienic storage and handling of laminated paperboard material must be considered to reduce the probability of package's contamination. All these measures together will ensure package's sterility that is imperative for the effectiveness of aseptic processing and consequently to ensure the microbiological stability of processed foods during shelf-life. (C) 2011 Elsevier Ltd. All rights reserved.

Thermal design of a tray-type distillation column of an ammonia/water absorption refrigeration cycle

The goal of this paper is to present an analysis of a segmented weir sieve-tray distillation column for a 17.58 kW (5 TR) ammonia/water absorption refrigeration cycle. Balances of mass and energy were performed based on the method of Ponchon-Savarit, from which it was possible to determine the ideal number of trays. The analysis showed that four ideal trays were adequate for that small absorption refrigeration system having the feeding system to the column right above the second tray. It was carried out a sensitivity analysis of the main parameters. Vapor and liquid pressure drop constraint along with ammonia and water mass flow ratios defined the internal geometrical sizes of the column, such as the column diameter and height, as well as other designing parameters. Due to the lack of specific correlations, the present work was based on practical correlations used in the petrochemical and beverage production industries. The analysis also permitted to obtain the recommended values of tray spacing in order to have a compact column. The geometry of the tray turns out to be sensitive to the charge of vapor and, to a lesser extent, to the load of the liquid, being insensible to the diameter of tray holes. It was found a column efficiency of 50%. Finally, the paper presents some recommendations in order to have an optimal geometry for a compact size distillation column. (c) 2011 Elsevier Ltd. All rights reserved.