A trade-off between maxima in efficiency and specific work output of super- and trans-critical CO2 Brayton cycles

Several operational aspects for thermal power plants in general are non-intuitive and involve simultaneous optimization of a number of operational parameters. In the case of solar operated power plants, it is even more difficult due to varying heat source temperatures induced by variability in insolation levels. This paper introduces a quantitative methodology for load regulation of a CO2 based Brayton cycle power plant using the `thermal efficiency and specific work output' coordinate system. The analysis shows that a transcritical CO2 cycle offers more flexibility under part load performance than the supercritical cycle in case of non-solar power plants. However, for concentrated solar power, where efficiency is important, supercritical CO2 cycle fares better than transcritical CO2 cycle. A number of empirical equations relating heat source temperature, high side pressure with efficiency and specific work output are proposed which could assist in generating control algorithms. (C) 2015 Elsevier B.V. All rights reserved.

Stability Analysis Of The Moving Interface In Piston- And Non-Piston-Like Displacements

From the macroscopic point of view, expressions involving reservoir and operational parameters are established for investigating the stability of moving interface in piston- and non-piston-like displacements. In the case of axi-symmetrical piston-like displacement, the stability is related to the moving interface position and water to oil mobility ratio. The capillary effect on the stability of moving interface depends on whether or not the moving interface is already stable and correlates with the wettability of the reservoir rock. In the case of non-piston-like displacement, the stability of the front is governed by both the relative permeability and the mobility ratio.

Remoção de metais pesados de efluentes sintéticos aquosos por nanofiltração

O objetivo deste trabalho foi estudar a remoção de metais pesados de efluentes sintéticos aquosos através de nanofiltração, com utilização de membrana de poliamida. A membrana utilizada constituída de poliamida apresentou uma boa permeabilidade hidráulica, constatada pela linearidade de fluxo com a variação de pressão de trabalho. Os metais estudados foram cobre, cádmio, zinco, chumbo e níquel com especiação de nitrato e sulfato. O desempenho do sistema foi verificado pela variação dos parâmetros operacionais (pressão e fluxo), associados também com a variação da salinidade e da concentração do metal. Em uma etapa inicial estudou-se a remoção de metais (nitrato e sulfato) isoladamente em uma mesma concentração molar, na pressão de 10 bar, comparando-se as rejeições com e sem agente complexante (EDTA). Em uma segunda etapa, estudou-se o desempenho da membrana, com misturas dos metais (nitrato) e mistura de metais (sulfato), também com e sem agente complexante, os resultados mostraram que a presença de agente complexante melhorou a rejeição dos metais. Nestas misturas estudaram-se os efeitos das concentrações (0,001; 0,0005 e 0,0001mol/L) e das pressões (5; 7; 10 e 12,5 bar) no sistema de remoção, constatou-se que o aumento da concentração e diminuição da pressão afeta a remoção. Em uma terceira etapa, estudou-se a influência da salinidade pela mistura de dois metais de mesma especiação (sulfato), comparando a remoção na pressão de 10 bar. Os resultados atestaram uma rejeição maior que 94 % para todos metais, na pressão de 10 bar, indicando um excelente desempenho e fluxo adequado, daí viabilidade de processo para todas as concentrações testadas. A pertinência do teste se justifica pela adequação do permeado ao atendimento aos padrões ambientais de concentração de metais e confirmam a eficácia do sistema de nanofiltração na remoção de metais pesados

吸收杂质热辐射诱导光学薄膜破坏的热力机制

光学元件的破坏是限制高功率激光系统发展的主要问题,理解光学元件的破坏机制对于高功率激光系统的设计、运行参量选择以及器件技术发展有重要影响。以热辐射模型为基础研究了杂质吸收诱导光学薄膜破坏的热力过程。研究发现薄膜发生初始破坏所需时间很短,脉冲的大部分时间是引起薄膜发生更大的破坏。在考虑吸收杂质发生相变的情况下,计算了吸收杂质汽化对薄膜产生的蒸汽压力,论证了薄膜发生宏观破坏的可能性。此模型能很好地解释光学薄膜的平底坑破坏形貌。

Estudo em Escala Piloto de Parâmetros de Monitoramento e Operação de Biopilhas no Tratamento de Solos Contaminados por Hidrocarbonetos de Petróleo

O objetivo do trabalho foi identificar ferramentas e indicadores adequados ao monitoramento e à otimização de processos de biorremediação, incluindo parâmetros físicos, químicos e microbiológicos definidos em estudos de tratabilidade de solos contaminados por óleo cru em escala de laboratório e comparar estratégias de biorremediação, tais como bioestímulo e bioaumento conduzidas em simulações de biopilhas dinâmicas ou estáticas. Quando três métodos de extração de hidrocarbonetos de petróleo de solo arenoso e franco-argiloso para análise cromatográfica (Soxhlet-SOX, microondas-MARS e extração acelerada por solvente-ASE) foram comparados entre si, concluiu-se que a técnica que promove a melhor recuperação depende da fração de interesse (n-alcanos, HRP, MCNR, HPA), das características texturais do solo (teores de areia, silte e argila) e da idade da contaminação. Dentre os indicadores de densidade populacional microbiana (microrganismos heterotróficos totais-PHT, população de fungos-PF e população microbiana degradadora de óleo (PDO) passíveis de utilização para indicar a taxa de degradação de compostos orgânicos presentes no solo tais como os hidrocarbonetos de petróleo, o PDO mostrou-se o mais adequado em conjunto com a produção de CO2 aferida pelo método respirométrico. Quando a estratégia de biorremediação de solo franco-argiloso contaminado com óleo cru a 3% (m m-1) utilizando bioestímulo (ajuste de pH, umidade e taxa C:N:P) foi comparada ao bioaumento (bioestímulo e adição de inóculo de microrganismos extraídos, enriquecidos e aclimatizados ao óleo cru como fonte de carbono), em sistemas de bancada simulando biopilha dinâmica (microcosmo M) e biopilha estática com aeração forçada (reator B), o tratamento que apresentou melhor remoção (32%) de HTP após 121 dias foi o bioaumento em biopilha estática. Para HPA, o tratamento que alcançou a melhor remoção (33%) foi com bioestímulo também em biopilha estática. A avaliação da taxa de mortalidade (%) de Eisenia andrei exposta tanto a solos recém-contaminados por óleo cru e preparados para bioestímulo (BIOS) e bioaumento (BIOA) a serem tratados em biopilhas dinâmicas e estáticas em escala de laboratório mostrou que após 56 dias de exposição da E. andrei, todos os solos produziram letalidade de 100%, quer fossem os solos recém-contaminados e preparados para os diferentes tratamentos (BIOS M, BIOS B, BIOA M, BIOA B) ou após 121 dias de tratamento. Tal resultado confirma que a biorremediação foi incipiente também do ponto de vista de remoção da ecotoxicidade. Em linhas gerais, a biorremediação de solo franco-argiloso contaminado por óleo cru, contendo tanto contaminação antiga quanto recente, reúne os maiores desafios à biorremediação, tanto do ponto de vista da composição textural do solo quanto da natureza do contaminante. Os processos são aparentemente lentos e requerem ferramentas auxiliares para aceleração dos mesmos. Recomenda-se no futuro, condução de experimentos com o uso de diferentes surfactantes, com ênfase em biosurfactantes

Coupled neutronic thermo-hydraulic analysis of full PWR core with Monte-Carlo based BGCore system

BGCore reactor analysis system was recently developed at Ben-Gurion University for calculating in-core fuel composition and spent fuel emissions following discharge. It couples the Monte Carlo transport code MCNP with an independently developed burnup and decay module SARAF. Most of the existing MCNP based depletion codes (e.g. MOCUP, Monteburns, MCODE) tally directly the one-group fluxes and reaction rates in order to prepare one-group cross sections necessary for the fuel depletion analysis. BGCore, on the other hand, uses a multi-group (MG) approach for generation of one group cross-sections. This coupling approach significantly reduces the code execution time without compromising the accuracy of the results. Substantial reduction in the BGCore code execution time allows consideration of problems with much higher degree of complexity, such as introduction of thermal hydraulic (TH) feedback into the calculation scheme. Recently, a simplified TH feedback module, THERMO, was developed and integrated into the BGCore system. To demonstrate the capabilities of the upgraded BGCore system, a coupled neutronic TH analysis of a full PWR core was performed. The BGCore results were compared with those of the state of the art 3D deterministic nodal diffusion code DYN3D (Grundmann et al.; 2000). Very good agreement in major core operational parameters including k-eff eigenvalue, axial and radial power profiles, and temperature distributions between the BGCore and DYN3D results was observed. This agreement confirms the consistency of the implementation of the TH feedback module. Although the upgraded BGCore system is capable of performing both, depletion and TH analyses, the calculations in this study were performed for the beginning of cycle state with pre-generated fuel compositions. © 2011 Published by Elsevier B.V.

Computational engineering design for micro-scale combustors

At present, optimisation is an enabling technology in innovation. Multi-objective and multi-disciplinary design tools are essential in the engineering design process, and have been applied successfully in aerospace and turbomachinery applications extensively. These approaches give insight into the design space and identify the trade-offs between the competing performance measures satisfying a number of constraints at the same time. It is anticipated here that the same benefits can be obtained for the design of micro-scale combustors. In this paper, a multi-disciplinary automated design optimisation system was developed for this purpose, which comprises a commercial computational fluid dynamics package and a multi-objective variant of the Tabu Search optimisation algorithm. The main objectives that are considered in this study are to optimise the main micro-scale combustor design characteristics and to satisfy manufacturability considerations from the very beginning of the whole design operation. Hydrogen-air combustion as well as 14 geometrical and 2 operational parameters are used to describe and model the design problem. Two illustrative test cases will be presented, in which the most important device operational requirements are optimised, and the efficiency of the developed optimisation system is demonstrated. The identification, assessment and suitability of the optimum design configurations are discussed in detail. Copyright © 2012 by ASME.

Computational engineering design for micro-scale combustion devices: A thermally improved configuration

A multi-objective design optimisation study has been carried out with the objectives to improve the overall efficiency of the device and to reduce the fuel consumption for the proposed micro-scale combustor design configuration. In a previous study we identified the topology of the combustion chamber that produced improved behaviour of the device in terms of the above design criteria. We now extend our design approach, and we propose a new configuration by the addition of a micro-cooling channel that will improve the thermal behaviour of the design as previously suggested in literature. Our initial numerical results revealed an improvement of 2.6% in the combustion efficiency when we applied the micro-cooling channel to an optimum design configuration we identified from our earlier multi-objective optimisation study, and under the same operating conditions. The computational modelling of the combustion process is implemented in the commercial computational fluid dynamics package ANSYS-CFX using Finite Rate Chemistry and a single step hydrogen-air reaction. With this model we try to balance good accuracy of the combustion solution and at the same time practicality within the context of an optimisation process. The whole design system comprises also the ANSYS-ICEM CFD package for the automatic geometry and mesh generation and the Multi-Objective Tabu Search algorithm for the design space exploration. We model the design problem with 5 geometrical parameters and 3 operational parameters subject to 5 design constraints that secure practicality and feasibility of the new optimum design configurations. The final results demonstrate the reliability and efficiency of the developed computational design system and most importantly we assess the practicality and manufacturability of the revealed optimum design configurations of micro-combustor devices. Copyright © 2013 by ASME.

Experiments of a diode-pumped Nd : GdVO4/LT-GaAs Q-switched and mode-locked laser

A diode-pumped passively Q-switched mode-locked (QML) Nd:GdVO4 laser with a low temperature GaAs (LT-GaAs) saturable absorber is presented. The maximal Q-switched mode-locked average output power was 798 mW with the Q-switched envelop having a repetition rate of 125 kHz. The mode-locked pulse trains inside the Q-switched pulse envelope had a repetition rate of similar to 750 MHz. The laser properties of the operational parameters on the pump power were also investigated experimentally.

Q-switched and mode-locked diode-pumped Nd : GdVO4 laser with low temperature GaAs saturable absorber

Low temperature GaAs (LT-GaAs) was successfully grown at the temperature of 550 degrees C by metal organic vapor phase epitaxy on a semi-insular GaAs substrate. With such an absorber as well as an output coupler we obtain Q-switched mode-locked (QML) 1064 nm Nd:GdVO4 laser pumped by diode laser with high repetition rate, formed with a simple flat-flat cavity. The repetition rate of the Q-switched envelope increased from 100 to 660 kHz as the pump power increased from 2.28 to 7.29 W. The mode-locked pulses inside the Q-switched pulse envelope had a repetition rate of similar to 1.36 GHz. A maximum average output power of 953 mW was obtained. The dependence of the operational parameters on the pump power was also investigated experimentally. (C) 2005 Elsevier B.V. All rights reserved.

Study on biomass circulation and gasification performance in a clapboard-type internal circulating fluidized bed gasifier

We investigated the solid particle flow characteristics and biomass gasification in a clapboard-type internal circulating fluidized bed reactor. The effect of fluidization velocity on particle circulation rate and pressure distribution in the bed showed that fluidization velocities in the high and low velocity zones were the main operational parameters controlling particle circulation. The maximum internal circulation rates in the low velocity zone came almost within the range of velocities in the high velocity zone, when uH/umf = 2.2-2.4 for rice husk and uH/umf = 3.5-4.5 for quartz sand. In the gasification experiment, the air equvalence ratio (ER) was the main controlling parameter. Rice husk gasification gas had a maximum heating value of around 5000 kJ/m3 when ER = 0.22-0.26, and sawdust gasification gas reached around 6000-6500 kJ/m3 when ER = 0.175-0.24. The gasification efficiency of rice husk reached a maximum of 77% at ER = 0.28, while the gasification efficiency of sawdust reached a maximum of 81% at ER = 0.25.

污染土壤中多环芳烃的共代谢降解过程

The biodegradation of most PAHs with high molecular weight is carried out by means of cometabolism. The development of the theory about cometabolic degradation is reviewed in this paper, and the achievements on the cometabolic degradations of PAHs are also summarized. It is demonstrated that glucose, biphenyl, organic acids and mineral oil could be used as cometabolic substrate to enhance the degradation rate of PAHs, and there are complex interactions in the microbiological degradation process among different PAHs. Some low molecular PAHs could serve as cometabolic substrate, which could also be used to enhance the transformation rate of high molecular weight recalcitrant PAHs. To achieve the cometabolic degradation of the PAHs in the soils, the following problems must be solved: the screening out of efficient degradative strains, the selection of the appropriate cometabolic substrate, the addition of surfactant if necessary and the optimization of operational parameters with the contaminated soils. These problems are the important parts of the project for the cometabolic degradation of PAHs in the soils.

Mathematical modelling: a laser soldering process for an optoelectronics butterfly package

For sensitive optoelectronic components, traditional soldering techniques cannot be used because of their inherent sensitivity to thermal stresses. One such component is the Optoelectronic Butterfly Package which houses a laser diode chip aligned to a fibre-optic cable. Even sub-micron misalignment of the fibre optic and laser diode chip can significantly reduce the performance of the device. The high cost of each unit requires that the number of damaged components, via the laser soldering process, are kept to a minimum. Mathematical modelling is undertaken to better understand the laser soldering process and to optimize operational parameters such as solder paste volume, copper pad dimensions, laser solder times for each joint, laser intensity and absorption coefficient. Validation of the model against experimental data will be completed, and will lead to an optimization of the assembly process, through an iterative modelling cycle. This will ultimately reduce costs, improve the process development time and increase consistency in the laser soldering process.

The application of electrostatic dry powder deposition technology to coat drug-eluting stents

Purpose: A novel methodology has been introduced to effectively coat intravascular stents with sirolimus-loaded polymeric microparticles. Methods: Dry powders of the microparticulate formulation, consisting of non-erodible polymers, were produced by a supercritical, aerosol, solvent extraction system (ASES). A design of experiment (DOE) approach was conducted on the independent variables, such as organic/CO2 phase volume ratio, polymer weight and stirring-rate, while regression analysis was utilized to interpret the influence of all operational parameters on the dependent variable of particle size. The dry powders, so formed, entered an electric field created by corona charging and were sprayed on the earthed metal stent. Furthermore, the thermal stability of sirolimus was investigated to define the optimum conditions for fusion to the metal surfaces. Results: The electrostatic dry powder deposition technology (EDPDT) was used on the metal strut followed by fusion to produce uniform, reproducible and accurate coatings. The coated stents exhibited sustained release profiles over 25 days, similar to commercial products. EDPDT-coated stents displayed significant reduced platelet adhesion. Conclusions: EDPDT appeared to be a robust accurate and reproducible technology to coat eluting stents.

Desenvolvimento de sensores de fibra óptica para monitorização de compostos orgânicos voláteis em ambientes industriais

O objectivo geral deste trabalho consistiu no desenvolvimento de novos sensores químicos de fibra óptica (OF) para análise de compostos orgânicos voláteis (VOCs) em ambientes industriais. A componente de detecção dos sensores desenvolvidos é constituída por uma pequena secção de fibra óptica revestida com um filme de polímero. A morfologia dos filmes poliméricos foi analisada e caracterizada por microscopia electrónica de varrimento (SEM), sendo a espessura dos filmes determinada por espectroscopia de retrodispersão de Rutherford (RBS, acrónimo do inglês Rutherford backscattering spectrometry). O desempenho analítico dos sensores de OF foi avaliado relativamente a diferentes parâmetros operacionais, tais como, concentração da solução de revestimento, técnica de deposição do filme polimérico, temperatura da célula de injecção, temperatura de cura do material polimérico, caudal do gás de arraste, comprimento de onda e frequência de funcionamento do laser, configurações estruturais da célula de injecção e do tubo analítico. Foram desenvolvidos dois sensores de OF a operar na região do infravermelho para determinação de diferentes classes de VOCs, nomeadamente hidrocarbonetos aromáticos, clorados e alifáticos, além de álcoois. Os sensores de OF desenvolvidos apresentaram adequadas características analíticas em termos de sensibilidade, linearidade, repetitibilidade e reprodutibilidade do sinal analítico, sendo o tempo de resposta de aproximadamente 30 segundos. Foi também desenvolvido um sensor de OF para especiação de benzeno, tolueno e o-xileno a operar na região do visível (635 - 650 nm), tendo sido aplicado à análise de amostras reais de ar de uma indústria de solventes. Relativamente à monitorização de VOCs em ambientes industriais, foi desenvolvido um sensor de OF para monitorização in situ e de forma remota (até uma distância máxima de 60 metros do local de amostragem) de benzeno, tolueno, etilbenzeno, p-xileno, m-xileno e o-xileno (BTEX), utilizando um díodo laser a 1550 nm. O desempenho analítico do sensor desenvolvido foi comparado, para a determinação de BTEX, com a cromatografia gasosa acoplada à detecção com ionização de chama (GC-FID). Foram ainda desenvolvidos dois detectores de fibra óptica acoplados a um cromatógrafo de gás para especiação de álcoois e hidrocarbonetos aromáticos. A metodologia desenvolvida baseada em cromatografia gasosa acoplada a um detector de fibra óptica (GC-OF) foi aplicada à análise de amostras reais de ar de uma indústria de solventes, comparando os respectivos resultados com os obtidos por GC-FID. Por fim foi efectuado um estudo visando a obtenção de um modelo geral para a resposta analítica dos sensores de fibra óptica desenvolvidos.