Analysis of an internally mountable accelerometer balance system for use with non-isotropic models in shock tunnels

Knowledge of drag force is an important design parameter in aerodynamics. Measurement of aerodynamic forces at hypersonic speed is a challenge and usually ground test facilities like shock tunnels are used to carry out such tests. Accelerometer based force balances are commonly employed for measuring aerodynamic drag around bodies in hypersonic shock tunnels. In this study, we present an analysis of the effect of model material on the performance of an accelerometer balance used for measurement of drag in impulse facilities. From the experimental studies performed on models constructed out of Bakelite HYLEM and Aluminum, it is clear that the rigid body assumption does not hold good during the short testing duration available in shock tunnels. This is notwithstanding the fact that the rubber bush used for supporting the model allows unconstrained motion of the model during the short testing time available in the shock tunnel. The vibrations induced in the model on impact loading in the shock tunnel are damped out in metallic model, resulting in a smooth acceleration signal, while the signal become noisy and non-linear when we use non-isotropic materials like Bakelite HYLEM. This also implies that careful analysis and proper data reduction methodologies are necessary for measuring aerodynamic drag for non-metallic models in shock tunnels. The results from the drag measurements carried out using a 60 degrees half angle blunt cone is given in the present analysis.

The Politics of Language in Romantic Literature

Marggraf Turley, R. (2002). The Politics of Language in Romantic Literature. Basingstoke: Palgrave Macmillan. RAE2008

Synthesis of new vegetable oil-based polymeric materials

A crescente procura de recursos fosseis a que se tem assistido nos ultimos anos, tem resultado num crescimento sem precedentes dos precos, com consequencias imprevisiveis e que levara, no espaco de decadas, ao seu inevitavel esgotamento. A procura de um modelo de desenvolvimento sustentavel, baseado em recursos renovaveis e o grande desafio que se coloca a civilizacao no seculo XXI. A biomassa vegetal, atraves das designadas gBio-refinarias h, e uma alternativa logica para a producao de produtos quimicos e de materiais mas tambem de combustiveis e energia. Os oleos vegetais constituem uma das fracoes da biomassa vegetal, cuja exploracao tem merecido redobrada atencao nos ultimos anos, como fonte de materiais e de combustiveis. Assim, a presente dissertacao tem por objetivo o desenvolvimento de novos materiais polimericos derivados de oleos vegetais, seguindo duas abordagens distintas, nomeadamente a preparacao de polimeros atraves de polimerizacao por etapas e polimerizacao em cadeia (Parte B e C, respetivamente). Em primeiro lugar, foram sintetizados poliesteres alifaticos de cadeia longa a partir de monomeros provenientes do oleo de colza (Capitulo III). A auto-metatese do acido erucico com catalisadores de rutenio, seguida de hidrogenacao da ligacao dupla, originou o acido 1,26-hexacosanodioico, que por sua vez foi convertido em hexacosano-1,26-diol. Subsequentemente, a policondensacao do acido ƒ¿,ƒÖ-dicarboxilico de cadeia longa com o hexacosano-1,26-diol originou o poliester 26,26. O diacido C26 foi tambem polimerizado com outros alcano-diois de cadeia curta, nomeadamente o dodecano-1,12-diol e o butano-1,2-diol, produzindo, respetivamente, os poliesteres 12,26 e 4,26. Estes poliesteres de fontes 100% renovaveis possuem valores de Mn na ordem dos 8-14 kDa e valores de PDI entre 2.1 e 2.7. As propriedades destes poliesteres alifaticos foram avaliadas atraves de varias tecnicas, revelando elevada cristalinidade (com uma estrutura cristalina como a do polietileno) e elevadas temperaturas de fusao (74-104 ‹C), cristalizacao (68-92 ‹C) e degradacao (323-386 ‹C). Em segundo lugar, foram sintetizados polimeros lineares termo-reversiveis a partir de derivados do oleo de ricinio (Capitulo IV). Para tal foram preparados monomeros que incorporam aneis furanicos inseridos atraves do acoplamento tiol-eno, e que posteriormente foram polimerizados pela reacao de Diels-Alder (DA) entre os grupos furano (dieno A) e estruturas complementares do tipo maleimida (dienofilo B). Para as polimerizacoes DA foram consideradas duas abordagens diferentes, nomeadamente (i) o uso de monomeros com dois aneis furanicos terminais em conjunto com uma bismaleimida (sistemas AA+BB) e (ii) a utilizacao de um monomero que incorpora ambos os grupos reativos, furano e maleimida, na sua estrutura (sistema AB). Este estudo demonstrou claramente que ambas as estratégias foram bem sucedidas embora com diferentes resultados em termos da natureza dos produtos obtidos. Estes polímeros lineares apresentam valores relativamente baixos de Tg (-40 to -2 °C) devido à natureza flexível dos grupos separadores das funções reativas, e de Mn (4.5-9.0 kDa) dada a observada tendência de ciclização associada a concentrações baixas de monómero. A aplicação da reação de retro-DA aos polímeros em causa confirmou o seu caráter reversível, ou seja, a possibilidade de promover, em condições controladas, a despolimerização com recuperação dos monómeros de partida. Esta particularidade abre caminhos para materiais macromoleculares originais com aplicações promissoras tais como auto-reparação e reciclabilidade. Em terceiro lugar, sintetizaram-se polímeros não-lineares termo-reversíveis a partir de derivados do óleo de ricínio (Capítulo V). Para tal foram preparados monómeros trifuncionais e posteriormente polimerizados através da reação de DA entre os grupos reativos complementares furano/maleimida. Foram consideradas três abordagens distintas para preparar estes polímeros não-lineares, nomeadamente através da utilização de (i) um monómero bisfurânico em combinação com uma trismaleimida (sistema A2+B3) e (ii) um monómero trisfurânico em conjunto com uma bismaleimida (sistema A3+B2) que originaram materiais ramificados ou reticulados, e ainda (iii) a utilização de monómeros assimetricamente substituídos do tipo A2B ou AB2 capazes de originar estruturas macromoleculares hiper-ramificadas. Todos os sistemas apresentaram valores de Tg perto de 0 °C, o que era de esperar para estes materiais não-lineares. A aplicação da reação de retro-DA comprovou mais uma vez o caráter termo-reversível das polimerizações em causa. Em quarto lugar e último lugar, foram preparados copolímeros de acetato de vinilo (VAc) com monómeros derivados de óleo de girassol (Capítulo VI). Ésteres vinílicos de ácidos gordos (FAVE) foram sintetizados por transvinilação dos ácidos oleico e linoleico com VAc catalisada por um complexo de irídio. Os monómeros vinílicos preparados foram caracterizados e posteriormente homopolimerizados e copolimerizados com VAc através do uso dos grupos vinílicos terminais como função inicial de polimerização. A variação do tipo e quantidade de monómero FAVE e da quantidade de iniciador radicalar originou copolímeros de VAc com valores de Mn na gama de 1.2-3.0 kDa e valores de Tg de -5 a 16 °C. Os copolímeros foram avaliados em testes de cura oxidativa através das insaturações nas suas cadeias alifáticas para formar materiais reticulados, e os resultados sugerem que eles podem ser sistemas efetivos de cura para aplicações como tintas, vernizes e outros tipos de revestimento. Todos os materiais poliméricos preparados ao longo deste trabalho constituem contribuições atrativas para a área dos polímeros oriundos de recursos renováveis e representam uma prova indiscutível de que os óleos vegetais são percursores promissores de materiais macromoleculares com potenciais aplicações.

Backside-surface imprinting as a new strategy to generate specific plastic antibody materials

A backside protein-surface imprinting process is presented herein as a novel way to generate specific synthetic antibody materials. The template is covalently bonded to a carboxylated-PVC supporting film previously cast on gold, let to interact with charged monomers and surrounded next by another thick polymer. This polymer is then covalently attached to a transducing element and the backside of this structure (supporting film plus template) is removed as a regular “tape”. The new sensing layer is exposed after the full template removal, showing a high density of re-binding positions, as evidenced by SEM. To ensure that the templates have been efficiently removed, this re-binding layer was cleaned further with a proteolytic enzyme and solution washout. The final material was named MAPS, as in the back-side reading of SPAM, because it acts as a back-side imprinting of this recent approach. It was able to generate, for the first time, a specific response to a complex biomolecule from a synthetic material. Non-imprinted materials (NIMs) were also produced as blank and were used as a control of the imprinting process. All chemical modifications were followed by electrochemical techniques. This was done on a supporting film and transducing element of both MAPS and NIM. Only the MAPS-based device responded to oxLDL and the sensing layer was insensitive to other serum proteins, such as myoglobin and haemoglobin. Linear behaviour between log(C, μg mL−1) versus charged tranfer resistance (RCT, Ω) was observed by electrochemical impedance spectroscopy (EIS). Calibrations made in Fetal Calf Serum (FCS) were linear from 2.5 to 12.5 μg mL−1 (RCT = 946.12 × log C + 1590.7) with an R-squared of 0.9966. Overall, these were promising results towards the design of materials acting close to the natural antibodies and applied to practical use of clinical interest.

Manufacture of garment materials

Functionalizing a broad range of stretchable substrates, including synthetic and natural fabrics, fibers and non-woven materials, by coating the substrates with various materials while the substrate is held stretched so as to maintain the breathability of the materials. This provides durability to the coatings and prolonged resistance to degradation due to washing and cleaning. One or both sides of the substrate may be treated to have different functional properties. A process is also provided for materials functionalization which can be compatible with the existing equipment.

Detection of cracks in scratching tests in ceramic materials through acoustic emission

The mechanisms of material removal and the interactions among scratches performed in ceramic materials were investigated using acoustic emission signals, and scanning electron microscopy, in scratching experiments. Several testing conditions were used to produce different types of removing mechanism on a glass as well as on a polycrystalline alumina sample composed by heterogeneous grain size. It is known that the material removing process on a polycrystalline ceramic involves intergranular microfracture and grain dislodgement, unlike the chipping produced by the extension of lateral cracks in non-granular materials, such as glass. Distinct settings for velocities, loads, and two types of diamond indenter were tested. The material removal was carried out by three different methods of scratching: single passes, repeated overlapping passes, and parallel scratches. As a general result, there was a clear relationship between the acoustic emission signals and the damage intensity occurred in the material removal. More specifically, there were differences in the acoustic emission signal levels in the scratches made on the alumina and on the glass owing to the material removal mechanisms associated with the structure of these materials. A gradual increase in the acoustic emission levels was observed when the number of repeated passes was increased as a result of the damage accumulation process followed by severe material removal. It was also noticed that the acoustic emission signals were capable of reflecting the interactions between two parallel scratches.

Analysis of elastic functionally graded materials under large displacements via high-order tetrahedral elements

The purpose of this study is to present a position based tetrahedral finite element method of any order to accurately predict the mechanical behavior of solids constituted by functionally graded elastic materials and subjected to large displacements. The application of high-order elements makes it possible to overcome the volumetric and shear locking that appears in usual homogeneous isotropic situations or even in non-homogeneous cases developing small or large displacements. The use of parallel processing to improve the computational efficiency, allows employing high-order elements instead of low-order ones with reduced integration techniques or strain enhancements. The Green-Lagrange strain is adopted and the constitutive relation is the functionally graded Saint Venant-Kirchhoff law. The equilibrium is achieved by the minimum total potential energy principle. Examples of large displacement problems are presented and results confirm the locking free behavior of high-order elements for non-homogeneous materials. (C) 2011 Elsevier B.V. All rights reserved.

Materials of engineering.

pt. I. Non-metallic materials of engineering: stone, timber, fuel, lubricants, etc. 5th rev. ed. 1899.--pt. II. Iron and steel. 9th rev. ed. 1903.--pt. III. Brasses, bronzes, and other alloys, and their constituent metals. 4th ed. rev. 1900.

Materials of engineering.

pt. 1. A treatise on non-metallic materials of engineering: Stone, timber, fuel, lubricants, etc. Fifth rev. ed.--pt. 2. A treatise on iron and steel. Ninth rev. ed.--pt. 3. A treatise on brasses, bronzes, and other alloys, and their constituent metals. Fourth ed. rev.

Development and evaluation of a non-destructive adhesion test

The object of this work was to further develop the idea introduced by Muaddi et al (1981) which enables some of the disadvantages of earlier destructive adhesion test methods to be overcome. The test is non-destructive in nature but it does need to be calibrated against a destructive method. Adhesion is determined by measuring the effect of plating on internal friction. This is achieved by determining the damping of vibrations of a resonating specimen before and after plating. The level of adhesion was considered by the above authors to influence the degree of damping. In the major portion of the research work the electrodeposited metal was Watt's nickel, which is ductile in nature and is therefore suitable for peel adhesion testing. The base metals chosen were aluminium alloys S1C and HE9 as it is relatively easy to produce varying levels of adhesion between the substrate and electrodeposited coating by choosing the appropriate process sequence. S1C alloy is the commercially pure aluminium and was used to produce good adhesion. HE9 aluminium alloy is a more difficult to plate alloy and was chosen to produce poorer adhesion. The "Modal Testing" method used for studying vibrations was investigated as a possible means of evaluating adhesion but was not successful and so research was concentrated on the "Q" meter. The method based on the use of a "Q" meter involves the principle of exciting vibrations in a sample, interrupting the driving signal and counting the number of oscillations of the freely decaying vibrations between two known preselected amplitudes of oscillations. It was not possible to reconstruct a working instrument using Muaddi's thesis (1982) as it had either a serious error or the information was incomplete. Hence a modified "Q" meter had to be designed and constructed but it was then difficult to resonate non-magnetic materials, such as aluminium, therefore, a comparison before and after plating could not be made. A new "Q" meter was then developed based on an Impulse Technique. A regulated miniature hammer was used to excite the test piece at the fundamental mode instead of an electronic hammer and test pieces were supported at the two predetermined nodal points using nylon threads. This instrument developed was not very successful at detecting changes due to good and poor pretreatments given before plating, however, it was more sensitive to changes at the surface such as room temperature oxidation. Statistical analysis of test results from untreated aluminium alloys show that the instrument is not always consistent, the variation was even bigger when readings were taken on different days. Although aluminium is said to form protective oxides at room temperature there was evidence that the aluminium surface changes continuously due to film formation, growth and breakdown. Nickel plated and zinc alloy immersion coated samples also showed variation in Q with time. In order to prove that the variations in Q were mainly due to surface oxidation, aluminium samples were lacquered and anodised Such treatments enveloped the active surfaces reacting with the environment and the Q variation with time was almost eliminated especially after hard anodising. This instrument detected major differences between different untreated aluminium substrates.Also Q values decreased progressively as coating thicknesses were increased. This instrument was also able to detect changes in Q due to heat-treatment of aluminium alloys.

Systematic screening of compressed ODT excipients:cellulosic versus non-cellulosic

The successful development of compressed ODTs utilises low compression forces to create a porous structure whereby excipients are added to enhance wicking/swelling action or provide strength to the fragile tablet framework. In this work, a systematic investigation comparing materials from two different categories was employed to understand their functionality in binary mixture tablets of the most commonly used diluent mannitol. Cellulose based excipients such as HPC (SSL-SFP), L-HPC (NBD-022) and MCC (Avicel PH-102) were compared with non-cellulosic materials such as PEO (POLYOX WSR N-10) and Crospovidone (XL-10). Pure excipient properties were studied using Heckel Plot, compressibility profile, SEM and XRPD, whereas the prepared binary mixture compacts were studied for hardness, disintegration time and friability. Results from our investigation provide insight into differences encountered in product performance of ODT upon inclusion of additional materials. For example, non-cellulosic excipients Polyox and Crospovidone showed higher plasticity (Py values 588 and 450MPa) in pure form but not in binary mixtures of mannitol. Cellulosic excipients, nonetheless, offer faster disintegration (<30 sec) specifically L-HPC and MCC tablets. Disintegration time for tablets with fully substituted-HPC was prolonged (200-500 sec) upon increasing concentration between 1-10% due to gelation/matrix formation. It can be concluded that despite the reasonably good plasticity of both cellulosic and non-cellulosic excipients in pure form, the mechanical strength in binary mixtures is negatively impacted by the fragmentation/fracture effect of mannitol. © 2014 Bentham Science Publishers.

Systematic screening of compressed ODT excipients : cellulosic versus non-cellulosic

The successful development of c ompressed ODTs utilises low compression force s to create a porous structure whereby excipients are added to enhance wicking/swelling action or p rovide strength to the fragile tablet framework. In this work, a systematic investigation comparing materials from two different categories was employed to understand their functionality in binary mixture tablets of the most commonly used diluent mannitol. Cellulose based excipients such as HPC (SSL-SFP), L-HPC (NBD -022) and MCC (Avicel PH -102 ) were compared with non -cellulosic materials such as PEO (POLYOX WSR N -10) and Crospovidone (XL -10). P ure excipient properties were studied using Heckel Plot, compre ssibility profile, SEM and XR PD, w hereas the prepared binary mixture compacts were studied for hardness, disintegration time and friability. Results from our investigation provide insight into differences encountered in product performance of ODT upon inclusion of additional materials. For example, non -cellulosic excipients Polyox and Crospovidone showed higher plasticity (Py values 588 and 450 MPa) in pure form but not in binary mixtures of mannitol . Cellulosic excipients, nonetheless, offer faster disintegration (

Bagasse Fractionation by the Soda Process

The soda process was the first chemical pulping method and was patented in 1845. Soda pulping led to kraft pulping, which involves the combined use of sodium hydroxide and sodium sulfide. Today, kraft pulping dominates the chemical pulping industry. However, about 10% of the total chemical pulp produced in the world is made using non-wood material, such as bagasse and wheat straw. The soda process is the preferred method of chemical pulping of non-wood materials, because it is considered to be economically viable on a small scale and for bagasse is compatible with sugarcane processing. With recent developments, the soda process can be designed to produce minimal effluent discharge and the fouling of evaporators by silica precipitation. The aim of this work is to produce bagasse fibres suitable for papermaking and allied applications and to produce sulfur-free lignin for use in specialty applications. A preliminary economic analysis of the soda process for producing commodity silica, lignin and pulp for papermaking is presented.

Sleeper [for laptop computer and live performer]

Sleeper is an 18'00" musical work for live performer and laptop computer which exists as both a live performance work and a recorded work for audio CD. The work has been presented at a range of international performance events and survey exhibitions. These include the 2003 International Computer Music Conference (Singapore) where it was selected for CD publication, Variable Resistance (San Francisco Museum of Modern Art, USA), and i.audio, a survey of experimental sound at the Performance Space, Sydney. The source sound materials are drawn from field recordings made in acoustically resonant spaces in the Australian urban environment, amplified and acoustic instruments, radio signals, and sound synthesis procedures. The processing techniques blur the boundaries between, and exploit, the perceptual ambiguities of de-contextualised and processed sound. The work thus challenges the arbitrary distinctions between sound, noise and music and attempts to reveal the inherent musicality in so-called non-musical materials via digitally re-processed location audio. Thematically the work investigates Paul Virilio’s theory that technology ‘collapses space’ via the relationship of technology to speed. Technically this is explored through the design of a music composition process that draws upon spatially and temporally dispersed sound materials treated using digital audio processing technologies. One of the contributions to knowledge in this work is a demonstration of how disparate materials may be employed within a compositional process to produce music through the establishment of musically meaningful morphological, spectral and pitch relationships. This is achieved through the design of novel digital audio processing networks and a software performance interface. The work explores, tests and extends the music perception theories of ‘reduced listening’ (Schaeffer, 1967) and ‘surrogacy’ (Smalley, 1997), by demonstrating how, through specific audio processing techniques, sounds may shifted away from ‘causal’ listening contexts towards abstract aesthetic listening contexts. In doing so, it demonstrates how various time and frequency domain processing techniques may be used to achieve this shift.