Effect of surface treatments on the shear bond strength of luting cements to Y-TZP ceramic

Statement of problem Because zirconia is a glass-free material, alternative surface treatments such as airborne-particle abrasion or silica coating should be used for long-term bonding. However, these surface treatments in combination with different bonding agents and luting cements have not yet been studied. Purpose The purpose of the study was to evaluate the effect of surface treatments on the shear bond strength (SBS) of luting cements to Y-TZP ceramic. Material and methods Zirconia disks (N=240) were airborne-particle abraded with the following particles (n=48): 50 μm Al2O3; 120 μm Al2O3; 30 μm silica-coated Al2O3 (Rocatec Soft); 120 μm Al2O3+110 μm silica-coated Al2O3 (Rocatec Plus); and Rocatec Plus. After silanization of the zirconia surface, composite resin disks were bonded with (n=12) RelyX Luting 2; RelyX ARC; RelyX U100; and Panavia F. The bonded specimens were thermocycled (10 000 cycles) and tested for SBS. Failure mode was determined with a stereomicroscope (×20). The morphology and elemental composition of airborne-particle abraded surfaces were evaluated with scanning electron microscopy (×500) and energy-dispersive x-ray spectroscopy (×50). Results Surface treatments, cements, and their interaction were significant (P<.001). For RelyX ARC, Rocatec Soft and Rocatec Plus provided the highest SBS. In general, surface treatments did not influence the SBS of RelyX U100 and Panavia F. Regardless of the cement, no significant difference was found between 50 μm and 120 μm Al2O3 particles, between Rocatec Soft and Rocatec Plus, or between Rocatec Plus and 120 μm Al2O3 particles+Rocatec Plus. All groups showed adhesive failures. Different particle sizes provided differences in morphological patterns. The elemental composition comprised Al and Al/Si for alumina and silica-abraded zirconia. Conclusions Particle size did not influence the SBS of the groups abraded exclusively with alumina or silica-coated particles. RelyX ARC was more surface-treatment dependent than RelyX U100 or Panavia F.

Interação entre odontologia restauradora e periodontia - parte 2: reanatomização dentária

The development of new dental materials has expanded dental therapeutic modalities ensuring excellence in aesthetic restorative treatments. Thus, the direct restorative procedures have been used in cases of dental reconstruction allowing an effective treatment with a low cost, while preserving healthy tooth structure. However, the clinician must be used to the techniques and the material in order to ensure longevity and success in the direct restorative procedure. The aim of this paper is to descrive, after completion of periodontal surgical procedures, the direct restorative step performed for dental reconstruction and diastema closure. The integration between Restorative Dentistry and periodontics enableb the restoration of a harmonious smile in a conservative manner, ensuring aesthetics and patient stisfaction.

Lichenoid reaction: case report

Lichenoid lesions are mucocutaneous disease of chronic inflammatory origin. Can produce side effects to drugs, dental materials, affecting 0.5 to 1% of the world population mainly in women in the fourth decade of life. The history and meticulous clinical servation may clarify the reactive nature, but the clinical diagnosis will only be conclusive when associated with tests such as histopathology. Therefore the objective of the study is to report a case of a woman of 55 years old, complaining of "white spots sore". Reported being allergic to metals, chocolate, acidic foods and certain types of clothes. From accurate intraoral clinical examination, white plaques were found in the dorsum of the tongue, hard palate and buccal mucosa, inaccurate and rough limits, and ulcerations throughout the labial edge and upper palate. Histopathology revealed a lichenoid reaction. Was instituted as pharmacological treatment, the use of systemic corticosteroids. Clinical follow-up of one year showed reduction of clinical symptoms, allowing to conclude that the clinical follow-up of this disease is necessary since its dubious malignant potential and diagnostic difficulty. Thus, early recognition of this disease allows instituting appropriate treatment with relief of anxiety of the patient and their family.

Análise mecânica e microestrutural das ligas de cobalto-cromo de uso odontológico após sucessivas refundições

The cobalt-chromium alloy is extensively used in the Odontology for the confection of metallic scaffolding in partial removable denture. During the last few years, it has been reported an increasing number of premature imperfections, with a few months of prosthesis use. The manufacture of these components is made in prosthetic laboratories and normally involves recasting, using parts of casting alloy and parts of virgin alloy. Therefore, the objective of the present study was to analyze the mechanical properties of a commercial cobalt-chromium alloy of odontological use after successive recasting, searching information to guide the dental prosthesis laboratories in the correct manipulation of the cobalt-chromium alloy in the process of casting and the possible limits of recasting in the mechanical properties of this material. Seven sample groups were confectioned, each one containing five test bodies, divided in the following way: G1: casting only with virgin alloy; G2: casting with 50% of the alloy of the G1 + 50% of virgin alloy; G3: casting with 50% of the alloy of the G2 + 50% of virgin alloy; G4: casting with 50% of the alloy of the G3 + 50% of virgin alloy; G5: 50% of alloy of the G4 + 50% of virgin alloy; G6: 50% of alloy of the G5 + 50% of virgin alloy and finally the G7, only with recasting alloy. The modifications in the mechanical behavior of the alloy were evaluated. Moreover, it was carried the micro structural characterization of the material by optic and electronic scanning microscopy, and X ray diffraction.and fluorescence looking into the correlatation of the mechanical alterations with structural modifications of the material caused by successive recasting process. Generally the results showed alterations in the fracture energy of the alloy after successive recasting, resulting mainly of the increasing presence of pores and large voids, characteristic of the casting material. Thus, the interpretation of the results showed that the material did not reveal significant differences with respect to the tensile strength or elastic limit, as a function of successive recasting. The elastic modulus increased from the third recasting cycle on, indicating that the material can be recast only twice. The fracture energy of the material decreased, as the number of recasting cycles increased. With respect to the microhardness, the statistical analyses showedno significant differences. Electronic scanning microscopy revealed the presence of imperfections and defects, resulting of the recasting process. X ray diffraction and fluorescence did not show alterations in the composition of the alloy or the formation of crystalline phases between the analyzed groups. The optical micrographs showed an increasing number of voids and porosity as the material was recast. Therefore, the general conclusion of this study is that the successive recasting of of Co-Cr alloys affects the mechanical properties of the material, consequently leading to the failure of the prosthetic work. Based on the results, the best recommendadition is that the use of the material should be limited to two recasting cycles

Caracterização Microestrutural e Tribocorrosiva de Sistemas Metalocerâmicos Odontológicos do Tipo Ni-Cr/Porcelana E Ni-Cr/Ti/Porcelana

The partial fixed prosthodontics restoration is used to rehabilitate form and function of partial or total compromised teeth, having to remain permanently joined to remainder tooth. The most useful material on prosthodontics is the feldspar porcelain, commercialized as aluminosilicate powders. Dental porcelains are presented with limited mechanical properties to rehabilitate extensive spaces. The association with Ni-Cr metallic systems (metal-ceramic system) allows that the metallic substructure compensates the fragile porcelain nature, preserving the thermal insulation and aesthetics desirable, as well as reducing the possibility of cracking during matication efforts. Cohesive flaws by low mechanical strength connect the metallic substructure to the oral environment, characterized by a electrolytic solution (saliva), by aggressive temperature, pH cyclic changes and mechanical requests. This process results on ionic liberation that could promote allergic or inflammatory responses, and/or clinical degradation of ceramometal system. The aim of this study was to evaluate the presence of an intermediate titanium layer on the microscopic fracture behavior of porcelains on ceramometal systems. Plasma deposition of titanium films result in regular passivating oxide layers which act as barriers to protect the metallic substrate against the hazardous effects of corrosive saliva. Tribocorrosion tests were performed to simulate the oral environment and mechanical stress, making it possible the early detection of crack formation and growth on metal-ceramic systems, which estimate the adherence between the compounds of this system. Plain samples consisting of dental feldspar porcelain deposited either onto metallic substrates or titanium films were fired and characterized by scanning electron microscopy. The result showed that the titanium film improved the adherence of the system compared to conventional metal-ceramic interfaces, thus holding crack propagation

Análise quantitativa de espectros de absorção no infravermelho de compósitos odontológicos fotoativados

Pós-graduação em Ciência dos Materiais - FEIS

Estudo do grau de conversão e dureza em compósitos odontológicos fotopolimerizáveis

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Aplicação do processo sol-gel na produção de recobrimentos de hidroxiapatita sobre ligas a base de Ti empregadas em implantes odontológicos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Síntese e caracterização de novos materiais compósitos orgânicos/inorgânicos, fotopolimerizáveis, para uso em restaurações odontológicas

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Síntese de membranas à base de híbridos orgânico-inorgânicos para implantes odontológicos

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Honorários praticados por operadoras de planos odontológicos e pelo SUS em relação aos definidos pelo Conselho Federal de Odontologia

Aim: The present study investigated the fees paid by dental insurance companies to dental surgeons, referrent to groups of dental procedures. Materials and Methods: The fees offered by dental insurance companies were defined according to the average values from the price tables of 5 insurance plans that offered national coverage. These average values and the values paid by the Brazilian Unified Health System (SUS) were compared with those set forth in the VRCC table from Brazilian Federal Dental Council (CFO). For comparison, average values were obtained for the following groups of procedures: preventive, aesthetic, endodontic, and surgical. The values of these preventive procedures were compared with other groups of procedures. Results: The plans applied an average discount of approximately 54.51% upon the prices suggested in the CFO price list. The highest discount was observed within the group of preventive procedures (57.09%, on average). Conclusion: The evaluated health insurance companies in vestigated in the present study are applying an abusive discount upon the prices suggested in the CFO price list. It's necessary to identify alternatives to reverse this situation.

Caracterização Microestrutural e Tribocorrosiva de Sistemas Metalocerâmicos Odontológicos do Tipo Ni-Cr/Porcelana E Ni-Cr/Ti/Porcelana

The partial fixed prosthodontics restoration is used to rehabilitate form and function of partial or total compromised teeth, having to remain permanently joined to remainder tooth. The most useful material on prosthodontics is the feldspar porcelain, commercialized as aluminosilicate powders. Dental porcelains are presented with limited mechanical properties to rehabilitate extensive spaces. The association with Ni-Cr metallic systems (metal-ceramic system) allows that the metallic substructure compensates the fragile porcelain nature, preserving the thermal insulation and aesthetics desirable, as well as reducing the possibility of cracking during matication efforts. Cohesive flaws by low mechanical strength connect the metallic substructure to the oral environment, characterized by a electrolytic solution (saliva), by aggressive temperature, pH cyclic changes and mechanical requests. This process results on ionic liberation that could promote allergic or inflammatory responses, and/or clinical degradation of ceramometal system. The aim of this study was to evaluate the presence of an intermediate titanium layer on the microscopic fracture behavior of porcelains on ceramometal systems. Plasma deposition of titanium films result in regular passivating oxide layers which act as barriers to protect the metallic substrate against the hazardous effects of corrosive saliva. Tribocorrosion tests were performed to simulate the oral environment and mechanical stress, making it possible the early detection of crack formation and growth on metal-ceramic systems, which estimate the adherence between the compounds of this system. Plain samples consisting of dental feldspar porcelain deposited either onto metallic substrates or titanium films were fired and characterized by scanning electron microscopy. The result showed that the titanium film improved the adherence of the system compared to conventional metal-ceramic interfaces, thus holding crack propagation

Comissão parlamentar de inquérito : o fato determinado e os limites materiais como garantidores dos direitos fundamentais

Analisa a limitação dos poderes das comissões parlamentares de inquérito e do fato determinado como garantidores do exercício dos direitos fundamentais no âmbito dessas mesmas comissões, a partir da doutrina sobre o assunto e da jurisprudência do Supremo Tribunal Federal. O enorme espaço que as CPIs têm na sociedade, aliado ao "poder de investigação próprio de autoridades judiciais", conferido pela Constituição Federal, nem sempre é compreendido pela maioria dos seus membros, que, não hesitam em dar a ela poderes jurisdicionais, privativos do Judiciário, gerando, desta forma, a violência contra os direitos fundamentais das testemunhas e pessoas por ela investigadas.

Retificação dos autógrafos do projeto de lei n° 24, de 2012-CN, em função da identificação de erros materiais; faculdade prevista na vigente Lei de Diretrizes Orçamentárias para 2013 e na resolução n° 1, de 2006-CN

Consultoria de Orçamento e Fiscalização Financeira. Núcleo Poderes, Justiça, Relações Exteriores, Defesa e Despesa Pessoal

Resistência à flexão e microestrutura de vidro-cerâmicas feldspáticas processadas por injeção em moldes à alta temperatura

Enquanto os métodos tradicionais de processamento de restaurações cerâmicas tornaram-se notórios por sua complexidade, as técnicas mais modernas vêm privilegiando a simplicidade de execução e a automação. Dentre estas, destaca-se a injeção em moldes, que recentemente, foi associada a métodos CAD-CAM. Estudos anteriores demonstraram a viabilidade de utilização de um vidro feldspático de baixa expansão térmica, Alpha (Vita Zahnfabrik), para injeção, porém, faltam informações quanto às propriedades mecânicas e a microestrutura deste material quando submetido à injeção. Os objetivos deste estudo são: produzir pastilhas vidrocerâmicas para injeção a quente a partir de Alpha e da mistura deste vidro com partículas de alumina e zircônia; avaliar a resistência à flexão dos materiais processados, e compará-la a um material compatível existente no mercado (PM9 - Vita Zahnfabrik); estudar a estrutura microscópica dos materiais e correlacioná-la com suas propriedades mecânicas; identificar por meio de difração de raios X a formação de fases cristalinas durante as diferentes etapas de processamento. A injeção aumentou a resistência do vidro Alpha devido à redução na quantidade e tamanho dos defeitos internos, principalmente porosidades. Apesar de ter sido observada nucleação de cristais nos dois materiais, durante o processamento, não foi possível determinar de que forma este fenômeno afetou as propriedades mecânicas dos materiais. Não foi detectada alteração no padrão de distribuição das fases cristalinas observadas em microscópio eletrônico de varredura antes e depois da injeção. Não foi verificada diferença estatística significante entre a resistência à flexão de Alpha injetado e PM9. A adição de partículas de alumina e zirconia ao vidro Alpha provocou redução da resistência, devido à formação de aglomerados durante a confecção das pastilhas e a incapacidade da injeção em dispersá-los. Tais aglomerados funcionaram como concentradores de tensões, enfraquecendo o material.