Power management techniques in an FPGA-Based WSN node for high performance application

In this work, the power management techniques implemented in a high-performance node for Wireless Sensor Networks (WSN) based on a RAM-based FPGA are presented. This new node custom architecture is intended for high-end WSN applications that include complex sensor management like video cameras, high compute demanding tasks such as image encoding or robust encryption, and/or higher data bandwidth needs. In the case of these complex processing tasks, yet maintaining low power design requirements, it can be shown that the combination of different techniques such as extensive HW algorithm mapping, smart management of power islands to selectively switch on and off components, smart and low-energy partial reconfiguration, an adequate set of save energy modes and wake up options, all combined, may yield energy results that may compete and improve energy usage of typical low power microcontrollers used in many WSN node architectures. Actually, results show that higher complexity tasks are in favor of HW based platforms, while the flexibility achieved by dynamic and partial reconfiguration techniques could be comparable to SW based solutions.

Impact of fire and post-fire management techniques on soil chemical properties

The effects of fire ( Control burned soil) and two emergency stabilisation techniques (grass Seeding and straw Mulching ) on 20 chemical characteristics were evaluated on 0 – 5 cm top-soils sampled 1, 90, 180 and 365 days after an experimental fi re in a steep shrubland of a temperate-humid region (NW Spain). Most part of pH (in H 2 O and KCl) variance was explained by the sampling date. No clear temporal trends were identi fi able for total soil C and N content, likely due to the large SOM pool in these soils; however, changes on soil δ 13 C were explained by the deposition of 13 C-depleted ashes, followed by its progressive erosion, while those on soil δ 15 N were a consequence of fi re induced N outputs. After the fi re, NH 4 + – N, P, Na, K, Mg, Ca, Mn, Cu, Zn and B concentrations increased, while those of NO 3 − – N, Al, Fe and Co did not vary significantly. Despite a significant decline with time, concentrations of Mg, Ca and Mn at the end of the study were still higher than in unburned soil, while those of K, Cu, Zn and B were similar to the pre-fire levels and those of NH 4 + – N, P and Na were below pre-fire values. Mulching and Seeding treatments for burned soil emergency stabilisation had significant effects on soil δ 15 N and extractable K, Mg and Ca, while data were inconclusive for their possible effects on the extractable Al, Fe and Co

Fault management techniques for systems with SRAM-based FPGAs

Las Field-Programmable Gate Arrays (FPGAs) SRAM se construyen sobre una memoria de configuración de tecnología RAM Estática (SRAM). Presentan múltiples características que las hacen muy interesantes para diseñar sistemas empotrados complejos. En primer lugar presentan un coste no-recurrente de ingeniería (NRE) bajo, ya que los elementos lógicos y de enrutado están pre-implementados (el diseño de usuario define su conexionado). También, a diferencia de otras tecnologías de FPGA, pueden ser reconfiguradas (incluso en campo) un número ilimitado de veces. Es más, las FPGAs SRAM de Xilinx soportan Reconfiguración Parcial Dinámica (DPR), la cual permite reconfigurar la FPGA sin interrumpir la aplicación. Finalmente, presentan una alta densidad de lógica, una alta capacidad de procesamiento y un rico juego de macro-bloques. Sin embargo, un inconveniente de esta tecnología es su susceptibilidad a la radiación ionizante, la cual aumenta con el grado de integración (geometrías más pequeñas, menores tensiones y mayores frecuencias). Esta es una precupación de primer nivel para aplicaciones en entornos altamente radiativos y con requisitos de alta confiabilidad. Este fenómeno conlleva una degradación a largo plazo y también puede inducir fallos instantáneos, los cuales pueden ser reversibles o producir daños irreversibles. En las FPGAs SRAM, los fallos inducidos por radiación pueden aparecer en en dos capas de arquitectura diferentes, que están físicamente superpuestas en el dado de silicio. La Capa de Aplicación (o A-Layer) contiene el hardware definido por el usuario, y la Capa de Configuración contiene la memoria de configuración y la circuitería de soporte. Los fallos en cualquiera de estas capas pueden hacer fracasar el sistema, lo cual puede ser ás o menos tolerable dependiendo de los requisitos de confiabilidad del sistema. En el caso general, estos fallos deben gestionados de alguna manera. Esta tesis trata sobre la gestión de fallos en FPGAs SRAM a nivel de sistema, en el contexto de sistemas empotrados autónomos y confiables operando en un entorno radiativo. La tesis se centra principalmente en aplicaciones espaciales, pero los mismos principios pueden aplicarse a aplicaciones terrenas. Las principales diferencias entre ambas son el nivel de radiación y la posibilidad de mantenimiento. Las diferentes técnicas para la gestión de fallos en A-Layer y C-Layer son clasificados, y sus implicaciones en la confiabilidad del sistema son analizados. Se proponen varias arquitecturas tanto para Gestores de Fallos de una capa como de doble-capa. Para estos últimos se propone una arquitectura novedosa, flexible y versátil. Gestiona las dos capas concurrentemente de manera coordinada, y permite equilibrar el nivel de redundancia y la confiabilidad. Con el objeto de validar técnicas de gestión de fallos dinámicas, se desarrollan dos diferentes soluciones. La primera es un entorno de simulación para Gestores de Fallos de C-Layer, basado en SystemC como lenguaje de modelado y como simulador basado en eventos. Este entorno y su metodología asociada permite explorar el espacio de diseño del Gestor de Fallos, desacoplando su diseño del desarrollo de la FPGA objetivo. El entorno incluye modelos tanto para la C-Layer de la FPGA como para el Gestor de Fallos, los cuales pueden interactuar a diferentes niveles de abstracción (a nivel de configuration frames y a nivel físico JTAG o SelectMAP). El entorno es configurable, escalable y versátil, e incluye capacidades de inyección de fallos. Los resultados de simulación para algunos escenarios son presentados y comentados. La segunda es una plataforma de validación para Gestores de Fallos de FPGAs Xilinx Virtex. La plataforma hardware aloja tres Módulos de FPGA Xilinx Virtex-4 FX12 y dos Módulos de Unidad de Microcontrolador (MCUs) de 32-bits de propósito general. Los Módulos MCU permiten prototipar Gestores de Fallos de C-Layer y A-Layer basados en software. Cada Módulo FPGA implementa un enlace de A-Layer Ethernet (a través de un switch Ethernet) con uno de los Módulos MCU, y un enlace de C-Layer JTAG con el otro. Además, ambos Módulos MCU intercambian comandos y datos a través de un enlace interno tipo UART. Al igual que para el entorno de simulación, se incluyen capacidades de inyección de fallos. Los resultados de pruebas para algunos escenarios son también presentados y comentados. En resumen, esta tesis cubre el proceso completo desde la descripción de los fallos FPGAs SRAM inducidos por radiación, pasando por la identificación y clasificación de técnicas de gestión de fallos, y por la propuesta de arquitecturas de Gestores de Fallos, para finalmente validarlas por simulación y pruebas. El trabajo futuro está relacionado sobre todo con la implementación de Gestores de Fallos de Sistema endurecidos para radiación. ABSTRACT SRAM-based Field-Programmable Gate Arrays (FPGAs) are built on Static RAM (SRAM) technology configuration memory. They present a number of features that make them very convenient for building complex embedded systems. First of all, they benefit from low Non-Recurrent Engineering (NRE) costs, as the logic and routing elements are pre-implemented (user design defines their connection). Also, as opposed to other FPGA technologies, they can be reconfigured (even in the field) an unlimited number of times. Moreover, Xilinx SRAM-based FPGAs feature Dynamic Partial Reconfiguration (DPR), which allows to partially reconfigure the FPGA without disrupting de application. Finally, they feature a high logic density, high processing capability and a rich set of hard macros. However, one limitation of this technology is its susceptibility to ionizing radiation, which increases with technology scaling (smaller geometries, lower voltages and higher frequencies). This is a first order concern for applications in harsh radiation environments and requiring high dependability. Ionizing radiation leads to long term degradation as well as instantaneous faults, which can in turn be reversible or produce irreversible damage. In SRAM-based FPGAs, radiation-induced faults can appear at two architectural layers, which are physically overlaid on the silicon die. The Application Layer (or A-Layer) contains the user-defined hardware, and the Configuration Layer (or C-Layer) contains the (volatile) configuration memory and its support circuitry. Faults at either layers can imply a system failure, which may be more ore less tolerated depending on the dependability requirements. In the general case, such faults must be managed in some way. This thesis is about managing SRAM-based FPGA faults at system level, in the context of autonomous and dependable embedded systems operating in a radiative environment. The focus is mainly on space applications, but the same principles can be applied to ground applications. The main differences between them are the radiation level and the possibility for maintenance. The different techniques for A-Layer and C-Layer fault management are classified and their implications in system dependability are assessed. Several architectures are proposed, both for single-layer and dual-layer Fault Managers. For the latter, a novel, flexible and versatile architecture is proposed. It manages both layers concurrently in a coordinated way, and allows balancing redundancy level and dependability. For the purpose of validating dynamic fault management techniques, two different solutions are developed. The first one is a simulation framework for C-Layer Fault Managers, based on SystemC as modeling language and event-driven simulator. This framework and its associated methodology allows exploring the Fault Manager design space, decoupling its design from the target FPGA development. The framework includes models for both the FPGA C-Layer and for the Fault Manager, which can interact at different abstraction levels (at configuration frame level and at JTAG or SelectMAP physical level). The framework is configurable, scalable and versatile, and includes fault injection capabilities. Simulation results for some scenarios are presented and discussed. The second one is a validation platform for Xilinx Virtex FPGA Fault Managers. The platform hosts three Xilinx Virtex-4 FX12 FPGA Modules and two general-purpose 32-bit Microcontroller Unit (MCU) Modules. The MCU Modules allow prototyping software-based CLayer and A-Layer Fault Managers. Each FPGA Module implements one A-Layer Ethernet link (through an Ethernet switch) with one of the MCU Modules, and one C-Layer JTAG link with the other. In addition, both MCU Modules exchange commands and data over an internal UART link. Similarly to the simulation framework, fault injection capabilities are implemented. Test results for some scenarios are also presented and discussed. In summary, this thesis covers the whole process from describing the problem of radiationinduced faults in SRAM-based FPGAs, then identifying and classifying fault management techniques, then proposing Fault Manager architectures and finally validating them by simulation and test. The proposed future work is mainly related to the implementation of radiation-hardened System Fault Managers.

Traffic calming, auto-restricted zones and other traffic management techniques: their effects on bicycling and pedestrians. Case study #19.

Federal Highway Administration, Washington, D.C.

Management techniques for foremen; questions and answers for all supervisors.

Loose-leaf.

Management techniques for foremen; questions and answers for all supervisors.

Mode of access: Internet.

A study on energy and environmental management techniques used in petroleum process industries

Petroleum process industries are one of the most energy and emission intensive sectors throughout the world.There are natural gas processing plant, crude oils and condensate fractionation plant, liquefied natural gas plantand liquefied petroleum gas plant etc. creates environmental pollution by processing and handling of petroleumproducts. The study critically reviewed and discussed the energy and environmental management includingpollution control of petroleum process industries of Bangladesh. They produce both gaseous (process gas, wastegas etc.) and liquid (produced water, waste oil and grease etc.) pollutants. The study found that the liquid pollutantlike waste water is more hazardous and its treatment process is highly complicated due to its higher salinity, morecorrosivity and grease contain characteristics. As part of energy management, the rational use of energy and energyflow diagram of the petroleum industry is presented. Finally, a time frame measures which can be implemented inorder to save energy is outlined. The study concluded that the rational use of energy and proper environmentalmanagement are essential for achieving energy and environmental sustainability of process industries.

Assessing organizational culture? value management to the rescue

As part of a Doctor of Business Administration degree programme jointly run by Curtin University, Perth, Australia and Lingnan University, Hong Kong, a research thesis relating organizational effectiveness to the organizational culture of Hong Kong construction firms involved in public housing is being undertaken. Organizational effectiveness is measured by the Housing Department (HD) Performance Assessment Scoring System (PASS) and organizational culture traits and strengths have been measured by using the Denison Organizational Culture Survey (OCS), developed by Daniel Denison and William S. Neale and based on 16 years of research involving over 1,000 organizations. The PASS scores of building contractors are compared with the OCS scores to determine if there is any significant correlation between highly effective companies and particular organizational strengths and traits. Profiles are then drawn using the Denison Model and can be compared against ‘norms’ for the industry sector on which the survey has been carried out. The next stage of the work is to present the results of the survey to individual companies, conduct focus group interviews to test the results, discover more detail on that company’s culture and discuss possible actions based on the results. It is in this latter stage that certain value management techniques may well prove very useful.

Grassland management and conversion into grassland: effects on soil carbon

Grasslands are heavily relied upon for food and forage production. A key component for sustaining production in grassland ecosystems is the maintenance of soil organic matter (SOM), which can be strongly influenced by management. Many management techniques intended to increase forage production may potentially increase SOM, thus sequestering atmospheric carbon (C). Further, conversion from either cultivation or native vegetation into grassland could also sequester atmospheric carbon. We reviewed studies examining the influence of improved grassland management practices and conversion into grasslands on soil C worldwide to assess the potential for C sequestration. Results from 115 studies containing over 300 data points were analyzed. Management improvements included fertilization (39%), improved grazing management (24%), conversion from cultivation (15%) and native vegetation (15%), sowing of legumes (4%) and grasses (2%), earthworm introduction (1%), and irrigation (1%). Soil C content and concentration increased with improved management in 74% of the studies, and mean soil C increased with all types of improvement. Carbon sequestration rates were highest during the first 40 yr after treatments began and tended to be greatest in the top 10 cm of soil. Impacts were greater in woodland and grassland biomes than in forest, desert, rain forest, or shrubland biomes. Conversion from cultivation, the introduction of earthworms, and irrigation resulted in the largest increases. Rates of C sequestration by type of improvement ranged from 0.11 3.04 Mg C.ha(-1) yr(-1), with a mean of 0.54 Mg C.ha(-1).yr(-1) and were highly influenced by biome type and climate. We conclude that grasslands can act as a significant carbon sink with the implementation of improved management.

Engaging operations management students by designing the unit with industry focus

Operations management is an area concerned with the production of goods and services ensuring that business operations are efficient in utilizing resource and effective to meet customer requirements. It deals with the design and management of products, processes, services and supply chains and considers the acquisition, development, and effective and efficient utilization of resources. Unlike other engineering subjects, content of these units could be very wide and vast. It is therefore necessary to cover the content that is most related to the contemporary industries. It is also necessary to understand what engineering management skills are critical for engineers working in the contemporary organisations. Most of the operations management books contain traditional Operations Management techniques. For example ‘inventory management’ is an important topic in operations management. All OM books deal with effective method of inventory management. However, new trend in OM is Just in time (JIT) delivery or minimization of inventory. It is therefore important to decide whether to emphasise on keeping inventory (as suggested by most books) or minimization of inventory. Similarly, for OM decisions like forecasting, optimization and linear programming most organisations now a day’s use software. Now it is important for us to determine whether some of these software need to be introduced in tutorial/ lab classes. If so, what software? It is established in the Teaching and Learning literature that there must be a strong alignment between unit objectives, assessment and learning activities to engage students in learning. Literature also established that engaging students is vital for learning. However, engineering units (more specifically Operations management) is quite different from other majors. Only alignment between objectives, assessment and learning activities cannot guarantee student engagement. Unit content must be practical oriented and skills to be developed should be those demanded by the industry. Present active learning research, using a multi-method research approach, redesigned the operations management content based on latest developments in Engineering Management area and the necessity of Australian industries. The redesigned unit has significantly helped better student engagement and better learning. It was found that students are engaged in the learning if they find the contents are helpful in developing skills that are necessary in their practical life.

Managing large collections of business process models - Current techniques and challenges

Nowadays, business process management is an important approach for managing organizations from an operational perspective. As a consequence, it is common to see organizations develop collections of hundreds or even thousands of business process models. Such large collections of process models bring new challenges and provide new opportunities, as the knowledge that they encapsulate requires to be properly managed. Therefore, a variety of techniques for managing large collections of business process models is being developed. The goal of this paper is to provide an overview of the management techniques that currently exist, as well as the open research challenges that they pose.

Management of the invasive hill raspberry (Rubus niveus) on Santiago Island, Galapagos: Eradication or indefinite control?

The eradication of an invasive plant species can provide substantial ecological and economic benefits by eliminating completely the negative effects of the weed and reducing the high cost of continuing control. A 5-yr program toward the eradication of hill raspberry (Rubus niveus Thunb.) in Santiago Island is evaluated using delimitation and extirpation criteria, as well as assessment of the ecological community response to management techniques. Currently, hill raspberry is located in the humid zone of Santiago island. It is distributed over three main infestations, small patches, and many scattered individuals within an area of approximately 1,000 ha. New infestations are constantly being found; every year, new detections add an area of approximately 175 ha. Adult and juvenile individuals are still found, both beyond and within known infestations. Both plant and seed bank density of hill raspberry decreased over time where infestations were controlled. Species composition in the seed bank and existing vegetation were significantly different between areas under intensive control and adjacent uninvaded forest. After 5 yr of intensive management, delimitation of hill raspberry has not been achieved; new populations are found every year, increasing the infested area that requires management. Off-target effects on native species resulting from control efforts seem to be substantial. Although a vast increase in economic investment would allow intensive searching that might enable all individuals to be found and controlled, the resultant disturbance and off-targets effects could outweigh the conservation benefits of eradication.

Fishery management plans and the development of artisanal fisheries in Nigeria: a review

Management of natural resources all over the world is of paramount importance to their sustainability in developing countries like Nigeria, there is less emphasis on proper management especially of fishery and other aquatic resources due to lack of sensitization and enlightenment of the rural dwellers who are closer to such natural resources. The main thrust of this review is to examine the management plans for Nigerian freshwater bodies (rivers and lakes) and the impact of such plans on the artisanal fisheries development in Nigeria. From the on-shelf information gathered there is scarcity of information on the management of Nigerian freshwater body's information available indicates that there is the traditional fisheries management and the government legal approach in form of fisheries Laws and Regulations. However, these management techniques are poorly carried out since there is a poor follow-up. Appreciable impact of fisheries management introduced on Kanji Lake by the Nigerian-German Kanji Lake Fisheries Promotion Project (NGKLFPP) between 1993 and 2001 proves worthwhile as this introduced some management measures such as implementation of fisheries Laws and Regulations, the ban of obnoxious fishing methods, introduction of fishing license, constitution of a management unit and appointment of liaison fishermen. Within the operative years of the project a lot of success was achieved and it is recommended that the approach in Kainji should be replicated in other freshwater bodies in Nigeria to alleviate poverty in the rural poor fishing communities

Ecology and management of water plants in lowland streams

A review article which discusses the ecology and management of common water plants in lowland streams, with an introduction containing a review of previous studies on the subject. The article covers the significance of seasonal growth, the significance of stand structure (particularly in relation to hydraulic resistence), an assessment of current river management, improvements to plant management techniques (in relation to cutting), and alternatives to the traditional techniques of river plant management. There are a number of accompanying figures.

Exogenous-Loss Awareness in Queue Management: Toward Global Fairness

For a given TCP flow, exogenous losses are those occurring on links other than the flow's bottleneck link. Exogenous losses are typically viewed as introducing undesirable "noise" into TCP's feedback control loop, leading to inefficient network utilization and potentially severe global unfairness. This has prompted much research on mechanisms for hiding such losses from end-points. In this paper, we show through analysis and simulations that low levels of exogenous losses are surprisingly beneficial in that they improve stability and convergence, without sacrificing efficiency. Based on this, we argue that exogenous loss awareness should be taken into account in any AQM design that aims to achieve global fairness. To that end, we propose an exogenous-loss aware Queue Management (XQM) that actively accounts for and leverages exogenous losses. We use an equation based approach to derive the quiescent loss rate for a connection based on the connection's profile and its global fair share. In contrast to other queue management techniques, XQM ensures that a connection sees its quiescent loss rate, not only by complementing already existing exogenous losses, but also by actively hiding exogenous losses, if necessary, to achieve global fairness. We establish the advantages of exogenous-loss awareness using extensive simulations in which, we contrast the performance of XQM to that of a host of traditional exogenous-loss unaware AQM techniques.