Cure Characteristics of Short Polyester Fiber-PolyurethaneElastomer Composite with Interfacial Bonding Agents Based on Polymeric 4,4'-Diphenylmethanediisocyanate

Cure characteristics of short polyester fiber-polyurethane composites with respect to different bonding agents (MD resins) based on 4, 4' diphenylmethanediisocyanate (MDI) and various diols like propyleneglycol (PG), polypropyleneglycol (PPG) and glycerol (GL) were studied. Tmax. - Tmin. of composites having MD resin were found to be higher than the composite without MD resin. Minimum torque and Tmax. - Tmin., scorch time and optimum cure time were increased with the increase of MDI equivalence. Optimum ratio of MDI / -of in the resin was found to be within the range of 1-1.5. It was observed from the cure characteristics that for getting better adhesion between short polyester fiber and the polyurethane matrix the best choice of MD resin was one based on MDI and 1:1 equivalent mixture of polypropyleneglycol and glycerol.

Novel Melt Transurethane Process for Cycloaliphatic Polyurethanes and Their Self-Organization for Nano-Materials

In this introduction part, importance has been given to the elastomeric properties of polyurethanes. Emphasis has been laid to this property based on microphase separation and how this could be modified by modifying the segment lengths, as well as the structure of the segments. Implication was also made on the mechanical and thermal properties of these copolymers based on various analytical methods usually used for characterization of polymers. A brief overview of the challenges faced by the polyurethane chemistry was also done, pointing to the fact that though polyurethane industry is more than 75 years old, still a lot of questions remain unanswered, that too mostly in the synthesis of polyurethanes. A major challenge in this industry is the utilization of more environmental friendly “Green Chemistry Routes” for the synthesis of polyurethanes which are devoid of any isocyanates or harsh solvents.The research work in this thesis was focused to develop non-isocyanate green chemical process for polyurethanes and also self-organize the resultant novel polymers into nano-materials. The thesis was focused on the following three major aspects:(i) Design and development of novel melt transurethane process for polyurethanes under non-isocyanate and solvent free melt condition. (ii) Solvent induced self-organization of the novel cycloaliphatic polyurethanes prepared by the melt transurethane process into microporous templates and nano-sized polymeric hexagons and spheres. (iii) Novel polyurethane-oligophenylenevinylene random block copolymer nano-materials and their photoluminescence properties. The second chapter of the thesis gives an elaborate discussion on the “Novel Melt Transurethane Process ” for the synthesis of polyurethanes under non-isocyanate and solvent free melt condition. The polycondensation reaction was carried out between equimolar amounts of a di-urethane monomer and a diol in the presence of a catalyst under melt condition to produce polyurethanes followed by the removal of low boiling alcohol from equilibrium. The polymers synthesized through this green chemical route were found to be soluble (devoid of any cross links), thermally stable and free from any isocyanate entities. The polymerization reaction was confirmed by various analytical techniques with specific references to the extent of reaction which is the main watchful point for any successful polymerization reaction. The mechanistic aspects of the reaction were another point of consideration for the novel polymerization route which was successfully dealt with by performing various model reactions. Since this route was successful enough in synthesizing polyurethanes with novel structures, they were employed for the solvent induced self-organization which is an important area of research in the polymer world in the present scenario. Chapter three mesmerizes the reader with multitudes of morphologies depending upon the chemical backbone structure of the polyurethane as well as on the nature and amount of various solvents employed for the self-organization tactics. The rationale towards these morphologies-“Hydrogen Bonding ” have been systematically probed by various techniques. These polyurethanes were then tagged with luminescent 0ligo(phenylene vinylene) units and the effects of these OPV blocks on the morphology of the polyurethanes were analyzed in chapter four. These blocks have resulted in the formation of novel “Blue Luminescent Balls” which could find various applications in optoelectronic devices as well as delivery vehicles.

Asma ocupacional y su relación con los isocianatos

El asma ocupacional es una enfermedad cuya prevalencia esta en aumento, tanto en países desarrollados como tercermundistas. La Organización Panamericana de la Salud (OPS) atribuye del 5% al 10% de la mortalidad por causas respiratorias al asma1. En el Reino Unido se calcula que uno de cada cinco trabajadores desarrolló esta enfermedad a causa de su trabajo2. Esta patología respiratoria es ocasionada por un ambiente ocupacional específico, los síntomas que comprenden disnea, sibilancias y tos entre otros, suelen presentarse veinticuatro horas después de la exposición y característicamente mejoran en los periodos de vacaciones y los fines de semana. Se debe diferenciar entre el asma agravada por el trabajo cuando el trabajador esta previamente diagnosticado y presenta síntomas de empeoramiento de su patología al entrar en contacto con la sustancia desencadenante; y el asma ocupacional clásica donde el trabajador desarrolla la enfermedad al exponerse a la sustancia irritante. Este es un problema creciente toda vez que no se accede con facilidad a los mecanismos necesarios para un diagnóstico y manejo oportuno de estos trabajadores, debido a que no se cuenta con la infraestructura necesaria para una reubicación oportuna y tampoco se instruye al personal médico de primer nivel en el diagnostico de esta patología. En esta revisión, se analizarán algunos estudios en los que se demuestra la relación entre la exposición a los Isocianatos y el desarrollo de asma ocupacional; se concluye pues, que si bien es importante realizar un diagnóstico correcto y oportuno, iniciar el manejo médico adecuado tambien es de vital importancia, resultando fundamental también capacitar al trabajador y empleador para proteger la salud y prevenir el desarrollo de esta patología tan dramática. PALABRAS

A modular flow reactor for performing Curtius rearrangements as a continuous flow process

The use of a mesofluidic flow reactor is described for performing Curtius rearrangement reactions of carboxylic acids in the presence of diphenylphosphoryl azide and trapping of the intermediate isocyanates with various nucleophiles.

Exploiting thermally-reversible chemistry for controlling the crosslinking of polymer networks

High explosives are highly sensitive to accidental detonation by impact, fire, shrapnel and small arms fire. This sensitivity can be reduced by storing the energetic material within a rubbery polymer matrix and are known as plastic bonded explosives (PBX). The current procedure used to manufacture PBX involves mixing the energetic material with a hydroxy-functionalised aliphatic polymer. Upon the addition of an isocyanate crosslinker an immediate polymerisation occurs and thus the rapidly curing mixture must be used to fill the missile or shells, referred to as ‘stores’. This process can lead to poor distribution of the crosslinker resulting in the formation of an inhomogeneously crosslinked matrix and the formation of voids. One solution to this problem involves containing the crosslinker within polyurethane microcapsules that are uniformly dispersed in the explosive-polymer mixture. Upon the application of a stimulus the crosslinker can be released from the microcapsules and the formation of a uniformly crosslinked PBX achieved. Herein is reported the design and synthesis of polyurethane microcapsules that release isocyanate crosslinkers when desired using a thermal stimulus. This has been achieved by exploiting the thermally-reversible nature of oxime-urethane and Diels-Alder adducts that have been incorporated into the shell wall of the microcapsules. An alternative approach to controlling the polymerisation of PBX materials has also been achieved using thermally-reversible blocked isocyanates that regenerate the isocyanate crosslinker when exposed to heat.

Suicide nucleophilic attack: Reactions of benzohydroxamate anion with bis(2,4-dinitrophenyl) phosphate

(Chemical Equation Presented) The reaction between the benzohydroxamate anion (BHO-) and bis(2,4-dinitrophenyl)phosphate (BDNPP) has been examined kinetically, and the products were characterized by mass and NMR spectroscopy. The nucleophilic attack of BHO- follows two reaction paths: (i) at phosphorus, giving an unstable intermediate that undergoes a Lossen rearrangement to phenyl isocyanate, aniline, diphenylurea, and O-phenylcarbamyl benzohydroxamate; and (ii) on the aromatic carbon, giving an intermediate that was detected but slowly decomposes to aniline and 2,4-dinitrophenol. Thus, the benzohydroxamate anion can be considered a self-destructive molecular scissor since it reacts and loses its nucleophilic ability. © 2009 American Chemical Society.

Studio di catalisi termoattivate per compositi poliuretanici

One of the key processing parameters in thermoset composites manufacturing is to have an optimum balance between open time and cure time. Long open times followed with a fast cure profile (also referred as snap cure or “hockey stick” shaped profiles) are required on applications like Pultrusion, Filament Winding, Resin Transfer Molding (RTM) and Infusion. In this work, several factors affecting the reactivity of a base line polyurethane formulation were studied. The addition of different components such as internal mold release agents, cross-linker, polyols having different molecular structure and isocyanates having different functionality were studied. A literature search was conducted to identify the main catalyst packages existing in the market. The reactivity of catalyst based on tertiary amines, orgamometallic salts, and co-catalyst of amine-organometallic complexes was characterized. Addition of quelants agents such as thioglycerol and acetyl acetone to delay the catalyst activity were also considered. As a consequence of this work a vast reactivity map was generated. This should guide the formulation designer in future product generations for the further development of the mentioned applications. Recommendations on measurements systems and further areas of exploration are also given.

Synthesis and applications of N-Metallo ketene imines

N-metallo ketene imines are attractive for the preparation of a wide range of organic compounds. Our research group has been engaged in the preparation and application of the N-metallo imines (SKIs). In this frame we have studied the uncatalyzed reaction of SKIs with isocyanates to give the corresponding malonamides with good yields. It has been demonstrated that the use of SKIs, instead of simple lithium anion of nitriles, is essential for the success of the reaction. A possible explanation assumes that this new reaction proceeds via a silatropism. In the course of our studies, reported in this thesis, the synthesis and the reactivity of N-silyl ketene imines in the preparation of 2,2-diaryl-3,4- dihydroxy- alcanonitrile in an uncatalyzed adol-type reaction has been performed. Our conception has been to use a chiral aldehyde to introduce asymmetric induction at the β-position and at the α-quaternary stereogenic center in the new forming diols. To achieve this goal, we used diarylacetonitrile as the substrate to form the corresponding N-trimethylsylilketene-imines to be reacted with (S)–lactic aldehyde with different protecting groups on the hydroxyl functionality. A number of 2,2-diaryl-3,4-dihydroxy-pentanenitrile were prepared with good to excellent stereo-control and satisfactory yields. Extension of this protocol to other metallo-ketene imines was performed. Accordingly, the preparation of tin ketene imines was attempted in analogy of the corresponding silyl ketene imine. The reaction of tin ketene imines with aldehydes was tested as a new tool for the synthesis of beta-hydroxynitriles starting from carbonyl compounds (aldehydes and/or ketones). Dialkyl(aryl)silyl nitriles and dialkyl(aryl)tin nitriles presents different reactivity. Finally, N-aluminium-ketene imines, as nucleophilic partner in the opening reaction of epoxides were studied. Preliminary positive results foster us to continue our studies in enlightening the scope and the limitations of this new reaction.

Synthesis and antibacterial evaluation of ureides of Baylis-Hillman derivatives

The synthesis of several 1-(2-cyano-3-aryl-allyl)-3-aryl-urea(thiourea) constructed from the reaction between allyl amines generated from Baylis-Hillman acetates and substituted isocyanates and isothiocyanates has been described. Further their cyclization in the presence of a base led to the formation of 5-arylmethyl-4-imino-3-aryl-3,4-dihydro-1H-pyrimidin-2-ones. All compounds were tested for their antibacterial activity. Few of the compounds showed superior activity or were equipotent to the standard antibacterial agents.

Marine isocyanides and related natural products structure, biosynthesis and ecology

This review highlights structural and biosynthetic work on a group of nitrogen-functionalised terpenes that are almost exclusively found in marine invertebrates and the animals that feed on them. The chemical functionality reviewed includes isocyanides, isothiocyanates, formamides, thiocyanates, isocyanates, and dichloroimines. The literature through mid 2003 is reviewed and there are 143 citations.

The curtius rearrangement of acyl azides revisited - formation of cyanate (R-O-CN)

The Curtius rearrangement is a synthesis of isocyanates (R-N=C=O) by thermal or photochemical rearrangement of acyl acides and/or acylnitrenes. The photochemical rearrangement of benzoyl azide is now shown for the first time to produce a small amount of phenyl cyanate (Ph-O-CN) together with phenyl isocyanate.

Cytotoxicity of 3,4-dihalogenated 2(5H)-furanones

Mucohalogen acids have been used for the preparation of a variety of 3,4-clihalogenated 2(5H)-furanones. In one synthetic step the carbarnates 2a-c and the pseudoanhydrides 4a-e were prepared using isocyanates and acid anhydrides. A series of 5-alkoxylated 3,4-dichloro-2(5H)-furanones 5a-o have been synthesized with a wide range of lipophilicity, using the hydroxy-form of mucohalogen acids 1a and 1b. The 5-allyl-3,4-dichloro-2(5H)-furanone 5f was derived into the dihydro-isoxazol 6 and the oxirane 7. The methyl ester 5a was converted with ammonia into the tetramic acid chloride 11. The pseudo acid chloride 3 was reacted further into the bis aziricline 8. Reduction of the mucochloric acid 1a furnished the trichlorofuranone 3. The cytotoxicity of these simple and bis-cyclic butenolides have been evaluated in tissue culture on MAC13 and MAC16 cancer cell lines using the MTT cytotoxicity assay. The ester 5g, the acetate 4b and the carbamate 2b displayed a cytotoxicity in the low micromolar range. Further, an IC50 (50% inhibitory concentration) of 50 nM and 30 nm was determined forthe epoxide 7 and the aziridine 18. © 2004 The Authors Recieved.

Studies of the cationic polymerisation of vinylic and energetic cyclic ether monomers

The cationic polymerisation of various monomers, including cyclic ethers bearing energetic nitrate ester (-ON02) groups, substituted styrenes and isobutylene has been investigated. The main reaction studied has been the ring-opening polymerisation of 3- (nitratomethyl)-3-methyl oxetane (NIMMO) using the alcohol/BF3.0Et2 binary initiator system. A series of di-, tri- and tetrafunctional telechelic polymers has been synthesised. In order to optimise the system, achieve controlled molecular weight polymers and understand the mechanism of polymerisation the effects of certain parameters on the molecular weight distribution, as determined by Size Exclusion Chromatography, have been examined. This shows the molecular weight achieved depends on a combination of factors including -OH concentration, addition rate of monomer and, most importantly, temperature. A lower temperature and OH concentration tends to produce higher molecular weight, whereas, slower addition rates of monomer, either have no significant effect or produce a lower molecular weight polymer. These factors were used to increase the formation of a cyclic oligomer, by a side reaction, and suggest, that the polymerisation of NIMMO is complicated with endbiting and back biting reactions, along with other transfer/termination processes. These observations appear to fit the model of an active-chain end mechanism. Another cyclic monomer, glycidyl nitrate (GLYN), has been polymerised by the activated monomer mechanism. Various other monomers have been used to end-cap the polymer chains to produce hydroxy ends which are expected to form more stable urethane links, than the glycidyl nitrate ends, when cured with isocyanates. A novel monomer, butadiene oxide dinitrate (BODN), has been prepared and its homopolymerisation and copolymerisation with GL YN studied. In concurrent work the carbocationic polymerisations of isobutylene or substituted styrenes have been studied. Materials with narrow molecular weight distributions have been prepared using the diphenyl phosphate/BCl3 initiator. These systems and monomers are expected to be used in the synthesis of thermoplastic elastomers.

Cyclic and acyclic modifications of 5-aminoimidazole-4-carboxamide

The Introduction gives a brief resume' of the biologically important aspects of 5 -aminoimidazole -4 -carbozamide (1) and explores., in-depth, the synthetic routes to this imidazole. All documented reactions of 5 -aninoimidanole-4 -carboxamide are reviewed in detail, with particular emphasis on the preparation and subsequent coupling reactions of 5 –diazo-imidazole-4 -carboxamide (6). A series of thirteen novel amide 5-amino-2-arylazoimidazole-4-carboxamide derivatives (117-129) were prepared by the coupling of aryldiazonium salts with 5-aminoimidazole-4-carboxamide. Chemical modification of these azo-dyes resulted in the preparation of eight previously unknown acyl derivatives (136-143) Interaction of 5-amino-2-arylazoimidazole-4-carboxides with ethyl formate in sodium ethoxide effected pyrimidine ring closure to the novel 8-arylazohypoxanthines (144 and 145). Several reductive techniques were employed in an effort to obtain the elusive 2,5-diaminoimidazole-4-carboxamide (71),a candidate chemotherapeutic agent, from the arylazoiridazoles. No success can be reported although 5-amino-2-(3-aminoindazol-2-yl) imidazole-4-carboxamide (151) was isolated due to a partial reduction and intramolecular cyclisation of 5-amino72-(2-cyanaphenylazo)imidazole-4-carboxamide (122) .Further possible synthetic approaches to the diaminoimidazole are discussed in Chapter 4. An interesting degradation of a known unstable nitrohydrazone is described in Chapter 5.This resulted in formation of 1, 1-bis(pyrazol--3-ylazo)-1-nitroethane (164) instead of the expected cyclisation to a bicyclic tetrazine N-oxide. An improved preparation of 5-diazoinidazole-4-carboxamide has been achieved, and the diazo-azole formed cycloadducts with isocyanates to yield the hitherto unknown imidazo[5,1-d][1,2,3,5]tetrazin-7(6H)-ones. Eleven derivatives (167-177) of this new ring-system were prepared and characterised. Chemical and spectroscopic investigation showed this ring-system to be unstable under certain conditions, and a comparative study of stability within the group has been made. "Retro-cycloaddition" under protic and photolytic conditions was an unexpected property of 6-substituted imidazo[5,1-d][1,2,3,5]tetrazin--7(0)-ones.Selected examples of the imidazotetrazinone ring-system were tested for antitumour activity. The results of biological evaluation are given in Chapter 7, and have culminated in a Patent application by the collaborating body, May and Baker Ltd. One compound,3-carbamoyl-6-(2-chloro-ethyl)imidazo[5,1-d][1,2,3,5jtetrazin-7(6H)-one (175),shows striking anti-tumour activity in rodent test systems.

Design of experiments to optimized the determination of TDIs in agglomerated cork stoppers

Isocyanates are included into a class with an extreme commercial importance because their use in the manufacture of polyurethanes. Polyurethanes are used in several applications such as adhesives, coatings, foams, thermoplastics resins, printing inks, foundry moulds and rubbers. Agglomerated cork stoppers are currently used for still wines, semi-sparkle and gaseous wines, beer and cider. Methylene diphenyl diisocyanate (MDI) is presently the isocyanate used in the production of polyurethane based adhesive in use due to its lowest toxicity comparing with toluene diisocyanate (TDI) previously employed. However, free monomeric TDI or MDI, depending on the based polyurethane, can migrate from agglomerated cork stoppers to beverages therefore it needs to be under control. The presence of these compounds are usually investigated by HPLC with Fluorescence or UV-Vis detector depending on the derivatising agent. Ultra Performance Liquid Chromatography with Diode Array Detector (UPLC-DAD) method is replacing HPLC. The objective of this study is to determine which method is better to analyze isocyanates from agglomerated cork stoppers, essentially TDI to quantify its monomer. A Design of Experiments (DOE) with three factors, column temperature, flow and solvent, at two levels was done. Eight experiments with three replications and two repetitions were developed. Through an ANOVA the significance of the factors was evaluated and the best level’s factors were selected. As the TDI has two isomers and in this method these two isomers were not always separated an ANOVA with results of resolution between peaks was performed. The Design of Experiments reveals to be a suitable statistical tool to determine the best conditions to quantified free isocyanates from agglomerated cork stoppers to real foodstuff. The best level’s factors to maximize area was column temperature at 30ºC, flow to 0,3 mL/min and solvent 0,1% Ammonium Acetate, to maximize resolution was the same except the solvent that was 0,01% Ammonium Acetate.