Online analysis of H2S and SO2 via advanced mid-Infrared gas sensors

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Evaluation of the zinox and zeolite materials as adsorbents to remove H2S from natural gas

MELO, Dulce Maria de Araújo et al. Evaluation of the Zinox and Zeolite materials as adsorbents to remove H2S from natural gas. Colloids and Surfaces. A, Physicochemical and Engineering Aspects, Estados Unidos, v. 272, p. 32-36, 2006.

Evaluation of the zinox and zeolite materials as adsorbents to remove H2S from natural gas

MELO, Dulce Maria de Araújo et al. Evaluation of the Zinox and Zeolite materials as adsorbents to remove H2S from natural gas. Colloids and Surfaces. A, Physicochemical and Engineering Aspects, Estados Unidos, v. 272, p. 32-36, 2006.

Room-temperature gas sensors based on gallium nitride nanoparticles

Room-temperature sensing characteristics for H-2, ethanol, NH3, H2S and water have been investigated with thick-film sensors based on GaN nanoparticles, prepared by a simple chemical route. In general, GaN nanoparticles exhibit satisfactory sensor properties for these gases and vapors even at room temperature. The sensitivity for ethanol is found to be highest, the sensitivity and recovery times being smallest. Gas sensor properties of GaN seem to be related to intrinsic defects, which act as sorption sites for the gas molecules. (c) 2010 Elsevier Ltd. All rights reserved.

Porous wide band gap BiNbO4 ceramic nanopowder synthesised by low temperature solution-based method for gas sensing applications

In this study, we report the gas sensing behavior of BiNbO4 nanopowder prepared by a low temperature simple solution-based method. Before the sensing behaviour study, the as-synthesized nanopowder was characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, UV-diffuse reflectance spectroscopy, impedance analysis, and surface area measurement. The NH3 sensing behavior of BiNbO4 was then studied by temperature modulation (50-350 degrees C) as well as concentration modulation (20-140 ppm). At the optimum operating temperature of 325 degrees C, the sensitivity was measured to be 90%. The cross-sensitivity of as-synthesized BiNbO4 sensor was also investigated by assessing the sensing behavior toward other gases such as hydrogen sulphide (H2S), ethanol (C2H5OH), and liquid petroleum gas (LPG). Finally, selectivity of the sensing material toward NH3 was characterized by observing the sensor response with gas concentrations in the range 20-140 ppm. The response and recovery time for NH3 sensing at 120 ppm were about 16 s and about 17 s, respectively.

H2O-CH4 and H2S-CH4 complexes: a direct comparison through molecular beam experiments and ab initio calculations

New molecular beam scattering experiments have been performed to measure the total ( elastic plus inelastic) cross sections as a function of the velocity in collisions between water and hydrogen sulfide projectile molecules and the methane target. Measured data have been exploited to characterize the range and strength of the intermolecular interaction in such systems, which are of relevance as they drive the gas phase molecular dynamics and the clathrate formation. Complementary information has been obtained by rotational spectra, recorded for the hydrogen sulfide-methane complex, with a pulsed nozzle Fourier transform microwave spectrometer. Extensive ab initio calculations have been performed to rationalize all the experimental findings. The combination of experimental and theoretical information has established the ground for the understanding of the nature of the interaction and allows for its basic components to be modelled, including charge transfer, in these weakly bound systems. The intermolecular potential for H2S-CH4 is significantly less anisotropic than for H2O-CH4, although both of them have potential minima that can be characterized as `hydrogen bonded'.

Reutilización de escoria negra de acería como soporte en biofiltros para la eliminación de H2S del biogás.

[EN]Due to the limitations associated with fossil fuels it is necessary to promote energy sources that are renewable as well as eco-friendly, such as biogas generated in anaerobic digesters. The biogas, composed principally of methane and CO2, is the result of the biodegradation of organic matter under anaerobic conditions. Its use as fuel is limited by the presence of minority compounds such as hydrogen sulphide (H2S); therefore, its pre-treatment is necessary. Currently there are various technologies for the removal of H2S from a gas stream, but most of them are based on physic-chemical treatments which have a number of drawbacks as reactive consumption, generation of secondary flows, etc. Biofiltration has been used as an efficient and low cost alternative to conventional purification processes, and excellent results for the degradation of H2S have been obtained. However process can be limited due to the progressive ageing of the support material, along with the loss of nutrients and other specific characteristics necessary for the good development of biomass. The purpose of this project is to develop a mixed support consisting of a mixture of an organic material and an inorganic support for its application in the removal of the H2S from biogas. This support material helps to optimize the characteristics of the bed and extend its lifespan. The development of such material will contribute to the implementation of biofiltration for treating biogas from anaerobic digesters for its use as biofuel. The inorganic material used is electric arc furnace (EAF) black slag, a by-product generated in large quantities in the production of steel in the Basque Country. Although traditionally the slag has been used in civil engineering, its physicochemical characteristics make it suitable for reuse as a filter medium in biofiltration. The main conclusion drawn from the experimental results is that EAF black slag is a suitable co-packing material in organic biofilters treating H2S-polluted gaseous streams. High pollutant removal rates have been achieved during the whole experimental period. The removal capacity recorded in biofilters with less inorganic material was higher than in those with higher slag portion. Nevertheless, all the biofilters have shown a satisfactory response even at high inlet loads (48 g·m-3·h-1), where the RE has not decreased over 82%.

Reducing H2S production by O-2 feedback control during large-scale sewage sludge composting

Hydrogen sulfide (H2S) production patterns and the influence of oxygen (O-2) concentration were studied based on a well operated composting plant. A real-time, online multi-gas detection system was applied to monitor the concentrations of H2S and O-2 in the pile during composting. The results indicate that H2S was mainly produced during the early stage of composting, especially during the first 40 h. Lack of available O-2 was the main reason for H2S production. Maintaining the O-2 concentration higher than 14% in the pile could reduce H2S production. This study suggests that shortening the interval between aeration or aerating continuously to maintain a high O-2 concentration in the pile was an effective strategy for restraining H2S production in sewage sludge composting. (C) 2010 Elsevier Ltd. All rights reserved.

COMPARISON OF THE SULFURIZATION OF COMOK/AL2O3 CATALYST WITH H2S AND CS2

Only H2S consumption and H2O formation was found in the sulfurization of CoMoK/Al2O3 water gas shift catalyst with H2S/H-2. but CO2 was formed first, then CH4, H2O and H2S appeared in the later part of TPS with CS2/H-2. Carbon deposition on the catalyst during the sulfurization with CS2/H-2 caused a lower activity than the catalyst sulfurized with H2S but could be removed in the run of WGS reaction.

Sensitive detection of H2S using gold nanoparticle decorated single-walled carbon nanotubes.

Herein, we demonstrate that highly sensitive conductometric gas nanosensors for H(2)S can be synthesized by electrodepositing gold nanoparticles on single-walled carbon nanotube (SWNT) networks. Adjusting the electrodeposition conditions allowed for tuning of the size and number of gold nanoparticles deposited. The best H(2)S sensing performance was obtained with discrete gold nanodeposits rather than continuous nanowires. The gas nanosensors could sense H(2)S in air at room temperature with a 3 ppb limit of detection. The sensors were reversible, and increasing the bias voltage reduced the sensor recovery time, probably by local Joule heating. The sensing mechanism is believed to be based on the modulation of the conduction path across the nanotubes emanating from the modulation of electron exchange between the gold and carbon nanotube defect sites when exposed to H(2)S.

Hydrogenation of S to H2S on Pt(111): A first-principles study

Density-functional theory has been used to investigate the chemisorption of S, SH, and H2S as well as the coadsorption of S and H and SH and H on Pt(111). In addition reaction pathways and energy profiles for the conversion of adsorbed S and H into gas-phase H2S have been determined. It has been found that S, SH, and H2S bind preferentially at face-centered-cubic (fcc), bridge, and top sites, respectively. Both the S+H and SH+H reactions have high barriers (similar to1 eV) and high exothermicities (similar to1 eV). This reveals that adsorbed H2S and SH are highly unstable adsorbates on Pt(111) and that adsorbed S (and H) is the most stable SHX (X=0,1,2) intermediate on Pt(111) (C) 2001 American Institute of Physics.

Electrochemical Oxidation of Hydrogen Sulfide at Platinum Electrodes in Room Temperature Ionic Liquids: Evidence for Significant Accumulation of H2S at the Pt/1-Butyl-3-methylimidazolium Trifluoromethylsulfonate Interface

Electrochemical oxidation of hydrogen sulfide gas (H2S) has been studied at a platinum microelectrode (10 mu m diameter) in five room temperature ionic liquids (RTILs): [C(4)mim][OTf], [C(4)dmim][NTf2], [C(4)mim][PF6],. [C(6)mim][FAP], and [P-14,P-6,P-6,P-6][FAP] (where [C-n mim](+) = 1-alkyl-3-methylimidazolium, [C(n)dmim](+) = 1-alkyl-2,3-dimethylimidazolium, [P-14,P-6,P-6,P-6](+) = tris(p-hexyl)-tetradecylphosphonium, [OTf](-) = trifluoromethlysulfonate, [NTf2](-) = bis(trifluoromethylsulfonyl)imide, [PF6](-) = hexafluorophosphate, and [FAP](-) = trifluorotris(pentafluoroethyl)phosphate). In four of the RTILs ([C(4)dmim][NTf2], [C(4)mim][PF6], [C(6)mim][FAP], and [P-14,P-6,P-6,P-6][FAP]), no clear oxidative signal was observed. In [C(4)mim][OTf], a chemically irreversible oxidation peak was observed on the oxidative sweep with no signal seen on the reverse scan. The oxidative signal showed an adsorptive stripping peak type followed by near steady-state limiting current behavior. Potential step chronoamperometry was carried out on the reductive wave, giving a diffusion coefficient and solubility of 1.6 x 10(-11) m(2) s(-1) and 7 mM, respectively (at 25 degrees C). Using these data, we modeled the oxidation signal kinetically, assuming adsorption preceded oxidation and that adsorption was approximately Langmuirian. The oxidation step was described by an electrochemically fully irreversible Tafel law/Butler-Volmer formalism. Modeling indicated a substantial buildup of H2S in the double layer in excess of the coverage that would be expected for a monolayer of chemisorbed H2S, reflecting high solubility of the gas in [C(4)mim][OTf] and possible attractive interactions with the [OTf](-) anions accumulated at the electrode at potentials positive of the potential of zero charge. Solute enrichment of the double layer in the solution adjacent to the electrode appears a novel feature of RTIL electrochemistry.

Limits on HDS/H2S abundance ratios in hot molecular cores

We have searched for HDS emission in a small number of hot cores. Using observations of (H2S)-S-34, we have derived upper limits to the [HDS]/[H2S] abundance ratio. The upper limits, which are close to 10(-3) can be interpreted in two ways, depending on whether grain surface reactions contribute to the formation of H2S. If grains do not dominate, then the H2S observed is formed in hot, post-shocked gas and a ratio close to the cosmic [D]/[H] ratio is expected for [HDS]/[H2S]. This scenario is consistent with our upper limits and with the relatively low abundance ratio found for [HDO]/[H2O] in hot cores but does not seem to account for all of the molecular [D]/[H] ratios observed in hot cores. If grains do dominate the formation of HBS, then the observed upper limit to the ratio is consistent with the formation of 'hot core ices' at a temperature of 60-80 K, close to the temperature at which cometary ices are thought to form.

Treatment of natural gas streams with ionic liquids

Being of high relevance for many technological applications, the solubility of sour gases in solvents of low volatility is still poorly described and understood. Aiming at purifying natural gas streams, the present work contributes for a more detailed knowledge and better understanding of the solubility of sour gases in these fluids, in particularly on ionic liquids. A new apparatus, developed and validated specially for phase equilibria studies of this type of systems, allowed the study of the solvent basicity, molecular weight and polarity influence on the absorption of carbon dioxide and methane. The non ideality of carbon dioxide solutions in ionic liquids and other low volatile solvents, with which carbon dioxide is known to form electron donor-acceptor complexes, is discussed, allowing the development of a correlation able to describe the carbon dioxide solubility in low volatile solvents. Furthermore, the non ideality of solutions of light compounds, such as SO2, NH3 and H2S, in ionic liquids is also investigated and shown to present negative deviations to the ideality in the liquid phase, that can be predicted by the Flory-Huggins model. For last, the effect of the ionic liquid polarity, described through the Kamlet-Taft parameters, on the CO2/CH4 and H2S/CH4 selectivities is also evaluated and shown to stand as a viable tool for the selection of ionic liquids with enhanced selectivities.

Caracterización de la exposición ocupacional a los gases, dióxido de azufre (so2), sulfuro de hidrógeno (h2s), y monóxido de carbono (co), y la percepción de salud de los trabajadores, en una empresa del sector hidrocarburo en Colombia

En el proceso de extracción de petróleo (crudo) deben realizarse tratamientos físicos y químicos en estaciones de recolección del hidrocarburo con el fin de garantizar su calidad antes de su entrega para el transporte y comercialización. Para la realización de esta actividad el personal operativo requerido (operadores) debe realizar diferentes actividades, tales como ronda operacional, verificación de sistemas de almacenamiento del crudo, agua residual del proceso e insumos químicos utilizados en su tratamiento y manipulación de facilidades en las estaciones de recolección, entre otras. Como resultados de las actividades rutinarias los operadores están expuestos a factores de riesgo químico asociados a gases y vapores orgánicos generados en los procesos de tratamiento del crudo. En el presente trabajo se realizaron mediciones de calidad de aire e higiene industrial en diferentes estaciones tratamiento de crudo, con el propósito de evaluar los niveles de exposición de los operadores a gases y vapores de hidrocarburos durante el proceso de tratamiento de crudo y dar respuesta a la siguiente pregunta: ¿existe relación entre la exposición ocupacional, las emisiones atmosféricas de gases (SO2, CO, H2S) y la percepción de afectación de la salud de los trabajadores que se encuentran expuestos durante la actividad laboral, en una empresa del sector de hidrocarburos? Se realizó un estudio de corte transversal, mediante la aplicación de cuestionarios sobre las condiciones de trabajo y de salud a 30 trabajadores que laboran en una estación de tratamiento de crudo de una compañía del sector de hidrocarburos. Los operadores objeto de estudio laboran en turnos rotativos, han estado vinculados con la compañía por más de dos años y tienen contrato directo, adicionalmente, se identificaron los factores de riesgos ambientales y ocupacionales para el grupo de trabajadores y se realizó una revisión de los informes de medición de higiene industrial y de calidad de aire de las estaciones donde labora el personal seleccionado con el fin de establecer si los resultados se relacionan. Los resultados obtenidos indican que el 100% de los trabajadores son de género masculino y se desempeñan en cargos de operadores, recorredores de pozos de crudo y supervisores. El 97% de los operadores tiene más de cuarenta años de edad y el 80% de los mismos ha laborado por más de 6 años en la compañía. Acerca de la percepción de los trabajadores sobre su estado de salud el 90% afirma que su salud es buena, el 97% respondió que no presenta problemas respiratorios, el 23% manifiesta que presenta trastornos dermatológicos y el 27% indican que presenta dolor de cabeza constante. De la revisión de los informes de calidad de aire disponibles se encontró que las mediciones de Dióxido de Azufre SO2, Monóxido de Carbono CO se encuentran dentro del rango definido como el de menor impacto para la salud humana. De los datos del informe se puede concluir que la calidad del aire es buena en el 100% de las áreas de influencia de las estaciones de tratamiento de crudo. Según los informes de higiene industrial el 34% de las instalaciones presenta concentraciones de Sulfuro de Hidrógeno (H2S) en el límite permisible para exposiciones crónicas en un promedio ponderado de tiempo (TLV-TWA) y el límite permisible para exposiciones agudas en un límite de exposición a corto plazo (TLV-STEL). Solo el 37% de los trabajadores objeto de este estudio percibe el riesgo por la exposición a factores de riesgo químicos y son claramente consientes que se encuentran expuestos a estos riesgos por la manipulación de productos químicos y exposición a sustancias químicas producto de sus actividades rutinarias, el 73% no percibe el riesgo de exposición por su actividad laboral. Se recomienda que la compañía fortalezca su esquema de vigilancia para generar alternativas que eleven los niveles de consciencia del riesgo del trabajador. Los factores de riesgo ambiental y ocupacional, de los gases y vapores generados se deben al proceso de tratamiento de crudo, están mutuamente relacionados dado que al generarse una emisión y/o escape no controlado como consecuencia se tiene una afectación directa al medio ambiente y a los trabajadores.