932 resultados para Gross operating margin


Relevância:

30.00% 30.00%

Publicador:

Resumo:

Gross pollutant traps (GPT) are designed to capture and retain visible street waste, such as anthropogenic litter and organic matter. Blocked screens, low/high downstream tidal waters and flows operating above/below the intended design limits can hamper the operations of a stormwater GPT. Under these adverse operational conditions, a recently developed GPT was evaluated. Capture and retention experiments were conducted on a 50% scale model with partially and fully blocked screens, placed inside a hydraulic flume. Flows were established through the model via an upstream channel-inlet configuration. Floatable, partially buoyant, neutrally buoyant and sinkable spheres were released into the GPT and monitored at the outlet. These experiments were repeated with a pipe-inlet configured GPT. The key findings from the experiments were of practical significance to the design, operation and maintenance of GPTs. These involved an optimum range of screen blockages and a potentially improved inlet design for efficient gross pollutant capture/retention operations. For example, the outlet data showed that the capture and retention efficiency deteriorated rapidly when the screens were fully blocked. The low pressure drop across the retaining screens and the reduced inlet flow velocities were either insufficient to mobilise the gross pollutants, or the GPT became congested.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

Intermittent generation from wind farms leads to fluctuating power system operating conditions pushing the stability margin to its limits. The traditional way of determining the worst case generation dispatch for a system with several semi-scheduled wind generators yields a conservative solution. This paper proposes a fast estimation of the transient stability margin (TSM) incorporating the uncertainty of wind generation. First, the Kalman filter (KF) is used to provide linear estimation of system angle and then unscented transformation (UT) is used to estimate the distribution of the TSM. The proposed method is compared with the traditional Monte Carlo (MC) method and the effectiveness of the proposed approach is verified using Single Machine Infinite Bus (SMIB) and IEEE 14 generator Australian dynamic system. This method will aid grid operators to perform fast online calculations to estimate TSM distribution of a power system with high levels of intermittent wind generation.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

Executive summary. In this report we analyse implementation costs and benefits for agricultural management practices, grouped into farming systems. In order to do so, we compare plot scale gross margins for the dominant agricultural production systems (sugarcane, grazing and banana cultivation) in the NRM regions Wet Tropics, Burdekin Dry Tropics and Mackay Whitsundays. Furthermore, where available, we present investment requirements for changing to improved farming systems. It must be noted that transaction costs are not captured within this project. For sugarcane, this economic analysis shows that there are expected benefits to sugarcane growers in the different regions through transitions to C and B class farming systems. Further transition to A-class farming systems can come at a cost, depending on the capital investment required and the length of the investment period. Obviously, the costs and benefits will vary for each individual grower and will depend on their starting point and individual property scenario therefore each circumstance needs to be carefully considered before making a change in management practice. In grazing, overall, reducing stocking rates comes at a cost (reduced benefits). However, when operating at low utilisation rates in wetter country, lowering stocking rates can potentially come at a benefit. With win-win potential, extension is preferred to assist farmer in changing management practices to improve their land condition. When reducing stocking rates comes at a cost, incentives may be applicable to support change among farmers. For banana cultivation, the results indicate that the transition to C and B class management practices is a worthwhile proposition from an economic perspective. For a change from B to A class farming systems however, it is not worthwhile from a financial perspective. This is largely due to the large capital investment associated with the change in irrigation system and negative impact in whole of farm gross margin. Overall, benefits will vary for each individual grower depending on their starting point and their individual property scenario. The results presented in this report are one possible set of figures to show the changes in profitability of a grower operating in different management classes. The results in this report are not prescriptive of every landholder. Landholders will have different costs and benefits from transitioning to improved practices, even if similar operations are practiced, hence it is recommended that landholders that are willing to change management undertake their own research and analysis into the expected costs and benefits for their own soil types and property circumstances.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

The pineapple crop are high potential for economic expression and social, but problems with productivity and management of production costs can be solved in order to ensure the sustainability of the farming system. The objective of this study was determine the cost of production and profitability of the pineapple's cultivation Pearl in Cassilandia-MS, under application of potassium doses fertilizer. The treatments consisted of the following doses of potassium (K2O): 0, 200, 400, 600, 800 kg ha(-1), used as a commercial source of potassium chloride (60% K2O). Were determined by estimating the effective operational cost (EOC), total operating cost (TOC), gross (RB), operating profitability (LO), profitability index (%), productivity of balance and equilibrium price. It was found that all treatments had operating profitability and positive profitability index. Potassium fertilization with 200 kg ha(-1) gave an average productivity of 50416.58 kg ha(-1), and also promoted the highest operating profit of R$ 9,108.97, the profit margin of 36.13% and best benefit cost (R$ 1.57).

Relevância:

30.00% 30.00%

Publicador:

Resumo:

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Relevância:

30.00% 30.00%

Publicador:

Resumo:

This paper presents an alternative methodology for loading margin improvement and total real power losses reduction by using a continuation method. In order to attain this goal, a parameterizing equation based on the total real power losses and the equations of the reactive power at the slack and generation buses are added to the conventional power flow equations. The voltages at these buses are considered as control variables and a new parameter is chosen to reduce the real power losses in the transmission lines. The results show that this procedure leads to maximum loading point increase and consequently, in static voltage stability margin improvement. Besides, this procedure also takes to a reduction in the operational costs and, simultaneously, to voltage profile improvement. Another important result of this methodology is that the resulting operating points are close to that provided by an optimal power flow program. © 2004 IEEE.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

El 10 de octubre de 2008 la Organización Marítima Internacional (OMI) firmó una modificación al Anexo VI del convenio MARPOL 73/78, por la que estableció una reducción progresiva de las emisiones de óxidos de azufre (SOx) procedentes de los buques, una reducción adicional de las emisiones de óxidos de nitrógeno (NOx), así como límites en las emisiones de dióxido de Carbono (CO2) procedentes de los motores marinos y causantes de problemas medioambientales como la lluvia ácida y efecto invernadero. Centrándonos en los límites sobre las emisiones de azufre, a partir del 1 de enero de 2015 esta normativa obliga a todos los buques que naveguen por zonas controladas, llamadas Emission Control Area (ECA), a consumir combustibles con un contenido de azufre menor al 0,1%. A partir del 1 de enero del año 2020, o bien del año 2025, si la OMI decide retrasar su inicio, los buques deberán consumir combustibles con un contenido de azufre menor al 0,5%. De igual forma que antes, el contenido deberá ser rebajado al 0,1%S, si navegan por el interior de zonas ECA. Por su parte, la Unión Europea ha ido más allá que la OMI, adelantando al año 2020 la aplicación de los límites más estrictos de la ley MARPOL sobre las aguas de su zona económica exclusiva. Para ello, el 21 de noviembre de 2013 firmó la Directiva 2012 / 33 / EU como adenda a la Directiva de 1999. Tengamos presente que la finalidad de estas nuevas leyes es la mejora de la salud pública y el medioambiente, produciendo beneficios sociales, en forma de reducción de enfermedades, sobre todo de tipo respiratorio, a la vez que se reduce la lluvia ácida y sus nefastas consecuencias. La primera pregunta que surge es ¿cuál es el combustible actual de los buques y cuál será el que tengan que consumir para cumplir con esta Regulación? Pues bien, los grandes buques de navegación internacional consumen hoy en día fuel oil con un nivel de azufre de 3,5%. ¿Existen fueles con un nivel de azufre de 0,5%S? Como hemos concluido en el capítulo 4, para las empresas petroleras, la producción de fuel oil como combustible marino es tratada como un subproducto en su cesta de productos refinados por cada barril de Brent, ya que la demanda de fuel respecto a otros productos está bajando y además, el margen de beneficio que obtienen por la venta de otros productos petrolíferos es mayor que con el fuel. Así, podemos decir que las empresas petroleras no están interesadas en invertir en sus refinerías para producir estos fueles con menor contenido de azufre. Es más, en el caso de que alguna compañía decidiese invertir en producir un fuel de 0,5%S, su precio debería ser muy similar al del gasóleo para poder recuperar las inversiones empleadas. Por lo tanto, el único combustible que actualmente cumple con los nuevos niveles impuestos por la OMI es el gasóleo, con un precio que durante el año 2014 estuvo a una media de 307 USD/ton más alto que el actual fuel oil. Este mayor precio de compra de combustible impactará directamente sobre el coste del trasporte marítimo. La entrada en vigor de las anteriores normativas está suponiendo un reto para todo el sector marítimo. Ante esta realidad, se plantean diferentes alternativas con diferentes implicaciones técnicas, operativas y financieras. En la actualidad, son tres las alternativas con mayor aceptación en el sector. La primera alternativa consiste en “no hacer nada” y simplemente cambiar el tipo de combustible de los grandes buques de fuel oil a gasóleo. Las segunda alternativa es la instalación de un equipo scrubber, que permitiría continuar con el consumo de fuel oil, limpiando sus gases de combustión antes de salir a la atmósfera. Y, por último, la tercera alternativa consiste en el uso de Gas Natural Licuado (GNL) como combustible, con un precio inferior al del gasóleo. Sin embargo, aún existen importantes incertidumbres sobre la evolución futura de precios, operación y mantenimiento de las nuevas tecnologías, inversiones necesarias, disponibilidad de infraestructura portuaria e incluso el desarrollo futuro de la propia normativa internacional. Estas dudas hacen que ninguna de estas tres alternativas sea unánime en el sector. En esta tesis, tras exponer en el capítulo 3 la regulación aplicable al sector, hemos investigado sus consecuencias. Para ello, hemos examinado en el capítulo 4 si existen en la actualidad combustibles marinos que cumplan con los nuevos límites de azufre o en su defecto, cuál sería el precio de los nuevos combustibles. Partimos en el capítulo 5 de la hipótesis de que todos los buques cambian su consumo de fuel oil a gasóleo para cumplir con dicha normativa, calculamos el incremento de demanda de gasóleo que se produciría y analizamos las consecuencias que este hecho tendría sobre la producción de gasóleos en el Mediterráneo. Adicionalmente, calculamos el impacto económico que dicho incremento de coste producirá sobre sector exterior de España. Para ello, empleamos como base de datos el sistema de control de tráfico marítimo Authomatic Identification System (AIS) para luego analizar los datos de todos los buques que han hecho escala en algún puerto español, para así calcular el extra coste anual por el consumo de gasóleo que sufrirá el transporte marítimo para mover todas las importaciones y exportaciones de España. Por último, en el capítulo 6, examinamos y comparamos las otras dos alternativas al consumo de gasóleo -scrubbers y propulsión con GNL como combustible- y, finalmente, analizamos en el capítulo 7, la viabilidad de las inversiones en estas dos tecnologías para cumplir con la regulación. En el capítulo 5 explicamos los numerosos métodos que existen para calcular la demanda de combustible de un buque. La metodología seguida para su cálculo será del tipo bottom-up, que está basada en la agregación de la actividad y las características de cada tipo de buque. El resultado está basado en la potencia instalada de cada buque, porcentaje de carga del motor y su consumo específico. Para ello, analizamos el número de buques que navegan por el Mediterráneo a lo largo de un año mediante el sistema AIS, realizando “fotos” del tráfico marítimo en el Mediterráneo y reportando todos los buques en navegación en días aleatorios a lo largo de todo el año 2014. Por último, y con los datos anteriores, calculamos la demanda potencial de gasóleo en el Mediterráneo. Si no se hace nada y los buques comienzan a consumir gasóleo como combustible principal, en vez del actual fuel oil para cumplir con la regulación, la demanda de gasoil en el Mediterráneo aumentará en 12,12 MTA (Millones de Toneladas Anuales) a partir del año 2020. Esto supone alrededor de 3.720 millones de dólares anuales por el incremento del gasto de combustible tomando como referencia el precio medio de los combustibles marinos durante el año 2014. El anterior incremento de demanda en el Mediterráneo supondría el 43% del total de la demanda de gasóleos en España en el año 2013, incluyendo gasóleos de automoción, biodiesel y gasóleos marinos y el 3,2% del consumo europeo de destilados medios durante el año 2014. ¿Podrá la oferta del mercado europeo asumir este incremento de demanda de gasóleos? Europa siempre ha sido excedentaria en gasolina y deficitaria en destilados medios. En el año 2009, Europa tuvo que importar 4,8 MTA de Norte América y 22,1 MTA de Asia. Por lo que, este aumento de demanda sobre la ya limitada capacidad de refino de destilados medios en Europa incrementará las importaciones y producirá también aumentos en los precios, sobre todo del mercado del gasóleo. El sector sobre el que más impactará el incremento de demanda de gasóleo será el de los cruceros que navegan por el Mediterráneo, pues consumirán un 30,4% de la demanda de combustible de toda flota mundial de cruceros, lo que supone un aumento en su gasto de combustible de 386 millones de USD anuales. En el caso de los RoRos, consumirían un 23,6% de la demanda de la flota mundial de este tipo de buque, con un aumento anual de 171 millones de USD sobre su gasto de combustible anterior. El mayor incremento de coste lo sufrirán los portacontenedores, con 1.168 millones de USD anuales sobre su gasto actual. Sin embargo, su consumo en el Mediterráneo representa sólo el 5,3% del consumo mundial de combustible de este tipo de buques. Estos números plantean la incertidumbre de si semejante aumento de gasto en buques RoRo hará que el transporte marítimo de corta distancia en general pierda competitividad sobre otros medios de transporte alternativos en determinadas rutas. De manera que, parte del volumen de mercancías que actualmente transportan los buques se podría trasladar a la carretera, con los inconvenientes medioambientales y operativos, que esto produciría. En el caso particular de España, el extra coste por el consumo de gasóleo de todos los buques con escala en algún puerto español en el año 2013 se cifra en 1.717 millones de EUR anuales, según demostramos en la última parte del capítulo 5. Para realizar este cálculo hemos analizado con el sistema AIS a todos los buques que han tenido escala en algún puerto español y los hemos clasificado por distancia navegada, tipo de buque y potencia. Este encarecimiento del transporte marítimo será trasladado al sector exterior español, lo cual producirá un aumento del coste de las importaciones y exportaciones por mar en un país muy expuesto, pues el 75,61% del total de las importaciones y el 53,64% del total de las exportaciones se han hecho por vía marítima. Las tres industrias que se verán más afectadas son aquellas cuyo valor de mercancía es inferior respecto a su coste de transporte. Para ellas los aumentos del coste sobre el total del valor de cada mercancía serán de un 2,94% para la madera y corcho, un 2,14% para los productos minerales y un 1,93% para las manufacturas de piedra, cemento, cerámica y vidrio. Las mercancías que entren o salgan por los dos archipiélagos españoles de Canarias y Baleares serán las que se verán más impactadas por el extra coste del transporte marítimo, ya que son los puertos más alejados de otros puertos principales y, por tanto, con más distancia de navegación. Sin embargo, esta no es la única alternativa al cumplimiento de la nueva regulación. De la lectura del capítulo 6 concluimos que las tecnologías de equipos scrubbers y de propulsión con GNL permitirán al buque consumir combustibles más baratos al gasoil, a cambio de una inversión en estas tecnologías. ¿Serán los ahorros producidos por estas nuevas tecnologías suficientes para justificar su inversión? Para contestar la anterior pregunta, en el capítulo 7 hemos comparado las tres alternativas y hemos calculado tanto los costes de inversión como los gastos operativos correspondientes a equipos scrubbers o propulsión con GNL para una selección de 53 categorías de buques. La inversión en equipos scrubbers es más conveniente para buques grandes, con navegación no regular. Sin embargo, para buques de tamaño menor y navegación regular por puertos con buena infraestructura de suministro de GNL, la inversión en una propulsión con GNL como combustible será la más adecuada. En el caso de un tiempo de navegación del 100% dentro de zonas ECA y bajo el escenario de precios visto durante el año 2014, los proyectos con mejor plazo de recuperación de la inversión en equipos scrubbers son para los cruceros de gran tamaño (100.000 tons. GT), para los que se recupera la inversión en 0,62 años, los grandes portacontenedores de más de 8.000 TEUs con 0,64 años de recuperación y entre 5.000-8.000 TEUs con 0,71 años de recuperación y, por último, los grandes petroleros de más de 200.000 tons. de peso muerto donde tenemos un plazo de recuperación de 0,82 años. La inversión en scrubbers para buques pequeños, por el contrario, tarda más tiempo en recuperarse llegando a más de 5 años en petroleros y quimiqueros de menos de 5.000 toneladas de peso muerto. En el caso de una posible inversión en propulsión con GNL, las categorías de buques donde la inversión en GNL es más favorable y recuperable en menor tiempo son las más pequeñas, como ferris, cruceros o RoRos. Tomamos ahora el caso particular de un buque de productos limpios de 38.500 toneladas de peso muerto ya construido y nos planteamos la viabilidad de la inversión en la instalación de un equipo scrubber o bien, el cambio a una propulsión por GNL a partir del año 2015. Se comprueba que las dos variables que más impactan sobre la conveniencia de la inversión son el tiempo de navegación del buque dentro de zonas de emisiones controladas (ECA) y el escenario futuro de precios del MGO, HSFO y GNL. Para realizar este análisis hemos estudiado cada inversión, calculando una batería de condiciones de mérito como el payback, TIR, VAN y la evolución de la tesorería del inversor. Posteriormente, hemos calculado las condiciones de contorno mínimas de este buque en concreto para asegurar una inversión no sólo aceptable, sino además conveniente para el naviero inversor. En el entorno de precios del 2014 -con un diferencial entre fuel y gasóleo de 264,35 USD/ton- si el buque pasa más de un 56% de su tiempo de navegación en zonas ECA, conseguirá una rentabilidad de la inversión para inversores (TIR) en el equipo scrubber que será igual o superior al 9,6%, valor tomado como coste de oportunidad. Para el caso de inversión en GNL, en el entorno de precios del año 2014 -con un diferencial entre GNL y gasóleo de 353,8 USD/ton FOE- si el buque pasa más de un 64,8 % de su tiempo de navegación en zonas ECA, conseguirá una rentabilidad de la inversión para inversores (TIR) que será igual o superior al 9,6%, valor del coste de oportunidad. Para un tiempo en zona ECA estimado de un 60%, la rentabilidad de la inversión (TIR) en scrubbers para los inversores será igual o superior al 9,6%, el coste de oportunidad requerido por el inversor, para valores del diferencial de precio entre los dos combustibles alternativos, gasóleo (MGO) y fuel oil (HSFO) a partir de 244,73 USD/ton. En el caso de una inversión en propulsión GNL se requeriría un diferencial de precio entre MGO y GNL de 382,3 USD/ton FOE o superior. Así, para un buque de productos limpios de 38.500 DWT, la inversión en una reconversión para instalar un equipo scrubber es más conveniente que la de GNL, pues alcanza rentabilidades de la inversión (TIR) para inversores del 12,77%, frente a un 6,81% en el caso de invertir en GNL. Para ambos cálculos se ha tomado un buque que navegue un 60% de su tiempo por zona ECA y un escenario de precios medios del año 2014 para el combustible. Po otro lado, las inversiones en estas tecnologías a partir del año 2025 para nuevas construcciones son en ambos casos convenientes. El naviero deberá prestar especial atención aquí a las características propias de su buque y tipo de navegación, así como a la infraestructura de suministros y vertidos en los puertos donde vaya a operar usualmente. Si bien, no se ha estudiado en profundidad en esta tesis, no olvidemos que el sector marítimo debe cumplir además con las otras dos limitaciones que la regulación de la OMI establece sobre las emisiones de óxidos de Nitrógeno (NOx) y Carbono (CO2) y que sin duda, requerirán adicionales inversiones en diversos equipos. De manera que, si bien las consecuencias del consumo de gasóleo como alternativa al cumplimiento de la Regulación MARPOL son ciertamente preocupantes, existen alternativas al uso del gasóleo, con un aumento sobre el coste del transporte marítimo menor y manteniendo los beneficios sociales que pretende dicha ley. En efecto, como hemos demostrado, las opciones que se plantean como más rentables desde el punto de vista financiero son el consumo de GNL en los buques pequeños y de línea regular (cruceros, ferries, RoRos), y la instalación de scrubbers para el resto de buques de grandes dimensiones. Pero, por desgracia, estas inversiones no llegan a hacerse realidad por el elevado grado de incertidumbre asociado a estos dos mercados, que aumenta el riesgo empresarial, tanto de navieros como de suministradores de estas nuevas tecnologías. Observamos así una gran reticencia del sector privado a decidirse por estas dos alternativas. Este elevado nivel de riesgo sólo puede reducirse fomentando el esfuerzo conjunto del sector público y privado para superar estas barreras de entrada del mercado de scrubbers y GNL, que lograrían reducir las externalidades medioambientales de las emisiones sin restar competitividad al transporte marítimo. Creemos así, que los mismos organismos que aprobaron dicha ley deben ayudar al sector naviero a afrontar las inversiones en dichas tecnologías, así como a impulsar su investigación y promover la creación de una infraestructura portuaria adaptada a suministros de GNL y a descargas de vertidos procedentes de los equipos scrubber. Deberían además, prestar especial atención sobre las ayudas al sector de corta distancia para evitar que pierda competitividad frente a otros medios de transporte por el cumplimiento de esta normativa. Actualmente existen varios programas europeos de incentivos, como TEN-T o Marco Polo, pero no los consideramos suficientes. Por otro lado, la Organización Marítima Internacional debe confirmar cuanto antes si retrasa o no al 2025 la nueva bajada del nivel de azufre en combustibles. De esta manera, se eliminaría la gran incertidumbre temporal que actualmente tienen tanto navieros, como empresas petroleras y puertos para iniciar sus futuras inversiones y poder estudiar la viabilidad de cada alternativa de forma individual. ABSTRACT On 10 October 2008 the International Maritime Organization (IMO) signed an amendment to Annex VI of the MARPOL 73/78 convention establishing a gradual reduction in sulphur oxide (SOx) emissions from ships, and an additional reduction in nitrogen oxide (NOx) emissions and carbon dioxide (CO2) emissions from marine engines which cause environmental problems such as acid rain and the greenhouse effect. According to this regulation, from 1 January 2015, ships travelling in an Emission Control Area (ECA) must use fuels with a sulphur content of less than 0.1%. From 1 January 2020, or alternatively from 2025 if the IMO should decide to delay its introduction, all ships must use fuels with a sulphur content of less than 0.5%. As before, this content will be 0.1%S for voyages within ECAs. Meanwhile, the European Union has gone further than the IMO, and will apply the strictest limits of the MARPOL directives in the waters of its exclusive economic zone from 2020. To this end, Directive 2012/33/EU was issued on 21 November 2013 as an addendum to the 1999 Directive. These laws are intended to improve public health and the environment, benefiting society by reducing disease, particularly respiratory problems. The first question which arises is: what fuel do ships currently use, and what fuel will they have to use to comply with the Convention? Today, large international shipping vessels consume fuel oil with a sulphur level of 3.5%. Do fuel oils exist with a sulphur level of 0.5%S? As we conclude in Chapter 4, oil companies regard marine fuel oil as a by-product of refining Brent to produce their basket of products, as the demand for fuel oil is declining in comparison to other products, and the profit margin on the sale of other petroleum products is higher. Thus, oil companies are not interested in investing in their refineries to produce low-sulphur fuel oils, and if a company should decide to invest in producing a 0.5%S fuel oil, its price would have to be very similar to that of marine gas oil in order to recoup the investment. Therefore, the only fuel which presently complies with the new levels required by the IMO is marine gas oil, which was priced on average 307 USD/tonne higher than current fuel oils during 2014. This higher purchasing price for fuel will have a direct impact on the cost of maritime transport. The entry into force of the above directive presents a challenge for the entire maritime sector. There are various alternative approaches to this situation, with different technical, operational and financial implications. At present three options are the most widespread in the sector. The first option consists of “doing nothing” and simply switching from fuel oil to marine gas oil in large ships. The second option is installing a scrubber system, which would enable ships to continue consuming fuel oil, cleaning the combustion gases before they are released to the atmosphere. And finally, the third option is using Liquefied Natural Gas (LNG), which is priced lower than marine gas oil, as a fuel. However, there is still significant uncertainty on future variations in prices, the operation and maintenance of the new technologies, the investments required, the availability of port infrastructure and even future developments in the international regulations themselves. These uncertainties mean that none of these three alternatives has been unanimously accepted by the sector. In this Thesis, after discussing all the regulations applicable to the sector in Chapter 3, we investigate their consequences. In Chapter 4 we examine whether there are currently any marine fuels on the market which meet the new sulphur limits, and if not, how much new fuels would cost. In Chapter 5, based on the hypothesis that all ships will switch from fuel oil to marine gas oil to comply with the regulations, we calculate the increase in demand for marine gas oil this would lead to, and analyse the consequences this would have on marine gas oil production in the Mediterranean. We also calculate the economic impact such a cost increase would have on Spain's external sector. To do this, we also use the Automatic Identification System (AIS) system to analyse the data of every ship stopping in any Spanish port, in order to calculate the extra cost of using marine gas oil in maritime transport for all Spain's imports and exports. Finally, in Chapter 6, we examine and compare the other two alternatives to marine gas oil, scrubbers and LNG, and in Chapter 7 we analyse the viability of investing in these two technologies in order to comply with the regulations. In Chapter 5 we explain the many existing methods for calculating a ship's fuel consumption. We use a bottom-up calculation method, based on aggregating the activity and characteristics of each type of vessel. The result is based on the installed engine power of each ship, the engine load percentage and its specific consumption. To do this, we analyse the number of ships travelling in the Mediterranean in the course of one year, using the AIS, a marine traffic monitoring system, to take “snapshots” of marine traffic in the Mediterranean and report all ships at sea on random days throughout 2014. Finally, with the above data, we calculate the potential demand for marine gas oil in the Mediterranean. If nothing else is done and ships begin to use marine gas oil instead of fuel oil in order to comply with the regulation, the demand for marine gas oil in the Mediterranean will increase by 12.12 MTA (Millions Tonnes per Annum) from 2020. This means an increase of around 3.72 billion dollars a year in fuel costs, taking as reference the average price of marine fuels in 2014. Such an increase in demand in the Mediterranean would be equivalent to 43% of the total demand for diesel in Spain in 2013, including automotive diesel fuels, biodiesel and marine gas oils, and 3.2% of European consumption of middle distillates in 2014. Would the European market be able to supply enough to meet this greater demand for diesel? Europe has always had a surplus of gasoline and a deficit of middle distillates. In 2009, Europe had to import 4.8 MTA from North America and 22.1 MTA from Asia. Therefore, this increased demand on Europe's already limited capacity for refining middle distillates would lead to increased imports and higher prices, especially in the diesel market. The sector which would suffer the greatest impact of increased demand for marine gas oil would be Mediterranean cruise ships, which represent 30.4% of the fuel demand of the entire world cruise fleet, meaning their fuel costs would rise by 386 million USD per year. ROROs in the Mediterranean, which represent 23.6% of the demand of the world fleet of this type of ship, would see their fuel costs increase by 171 million USD a year. The greatest cost increase would be among container ships, with an increase on current costs of 1.168 billion USD per year. However, their consumption in the Mediterranean represents only 5.3% of worldwide fuel consumption by container ships. These figures raise the question of whether a cost increase of this size for RORO ships would lead to short-distance marine transport in general becoming less competitive compared to other transport options on certain routes. For example, some of the goods that ships now carry could switch to road transport, with the undesirable effects on the environment and on operations that this would produce. In the particular case of Spain, the extra cost of switching to marine gas oil in all ships stopping at any Spanish port in 2013 would be 1.717 billion EUR per year, as we demonstrate in the last part of Chapter 5. For this calculation, we used the AIS system to analyse all ships which stopped at any Spanish port, classifying them by distance travelled, type of ship and engine power. This rising cost of marine transport would be passed on to the Spanish external sector, increasing the cost of imports and exports by sea in a country which relies heavily on maritime transport, which accounts for 75.61% of Spain's total imports and 53.64% of its total exports. The three industries which would be worst affected are those with goods of lower value relative to transport costs. The increased costs over the total value of each good would be 2.94% for wood and cork, 2.14% for mineral products and 1.93% for manufactured stone, cement, ceramic and glass products. Goods entering via the two Spanish archipelagos, the Canary Islands and the Balearic Islands, would suffer the greatest impact from the extra cost of marine transport, as these ports are further away from other major ports and thus the distance travelled is greater. However, this is not the only option for compliance with the new regulations. From our readings in Chapter 6 we conclude that scrubbers and LNG propulsion would enable ships to use cheaper fuels than marine gas oil, in exchange for investing in these technologies. Would the savings gained by these new technologies be enough to justify the investment? To answer this question, in Chapter 7 we compare the three alternatives and calculate both the cost of investment and the operating costs associated with scrubbers or LNG propulsion for a selection of 53 categories of ships. Investing in scrubbers is more advisable for large ships with no fixed runs. However, for smaller ships with regular runs to ports with good LNG supply infrastructure, investing in LNG propulsion would be the best choice. In the case of total transit time within an ECA and the pricing scenario seen in 2014, the best payback periods on investments in scrubbers are for large cruise ships (100,000 gross tonnage), which would recoup their investment in 0.62 years; large container ships, with a 0.64 year payback period for those over 8,000 TEUs and 0.71 years for the 5,000-8,000 TEU category; and finally, large oil tankers over 200,000 deadweight tonnage, which would recoup their investment in 0.82 years. However, investing in scrubbers would have a longer payback period for smaller ships, up to 5 years or more for oil tankers and chemical tankers under 5,000 deadweight tonnage. In the case of LNG propulsion, a possible investment is more favourable and the payback period is shorter for smaller ship classes, such as ferries, cruise ships and ROROs. We now take the case of a ship transporting clean products, already built, with a deadweight tonnage of 38,500, and consider the viability of investing in installing a scrubber or changing to LNG propulsion, starting in 2015. The two variables with the greatest impact on the advisability of the investment are how long the ship is at sea within emission control areas (ECA) and the future price scenario of MGO, HSFO and LNG. For this analysis, we studied each investment, calculating a battery of merit conditions such as the payback period, IRR, NPV and variations in the investors' liquid assets. We then calculated the minimum boundary conditions to ensure the investment was not only acceptable but advisable for the investor shipowner. Thus, for the average price differential of 264.35 USD/tonne between HSFO and MGO during 2014, investors' return on investment (IRR) in scrubbers would be the same as the required opportunity cost of 9.6%, for values of over 56% ship transit time in ECAs. For the case of investing in LNG and the average price differential between MGO and LNG of 353.8 USD/tonne FOE in 2014, the ship must spend 64.8% of its time in ECAs for the investment to be advisable. For an estimated 60% of time in an ECA, the internal rate of return (IRR) for investors equals the required opportunity cost of 9.6%, based on a price difference of 244.73 USD/tonne between the two alternative fuels, marine gas oil (MGO) and fuel oil (HSFO). An investment in LNG propulsion would require a price differential between MGO and LNG of 382.3 USD/tonne FOE. Thus, for a 38,500 DWT ship carrying clean products, investing in retrofitting to install a scrubber is more advisable than converting to LNG, with an internal rate of return (IRR) for investors of 12.77%, compared to 6.81% for investing in LNG. Both calculations were based on a ship which spends 60% of its time at sea in an ECA and a scenario of average 2014 prices. However, for newly-built ships, investments in either of these technologies from 2025 would be advisable. Here, the shipowner must pay particular attention to the specific characteristics of their ship, the type of operation, and the infrastructure for supplying fuel and handling discharges in the ports where it will usually operate. Thus, while the consequences of switching to marine gas oil in order to comply with the MARPOL regulations are certainly alarming, there are alternatives to marine gas oil, with smaller increases in the costs of maritime transport, while maintaining the benefits to society this law is intended to provide. Indeed, as we have demonstrated, the options which appear most favourable from a financial viewpoint are conversion to LNG for small ships and regular runs (cruise ships, ferries, ROROs), and installing scrubbers for large ships. Unfortunately, however, these investments are not being made, due to the high uncertainty associated with these two markets, which increases business risk, both for shipowners and for the providers of these new technologies. This means we are seeing considerable reluctance regarding these two options among the private sector. This high level of risk can be lowered only by encouraging joint efforts by the public and private sectors to overcome these barriers to entry into the market for scrubbers and LNG, which could reduce the environmental externalities of emissions without affecting the competitiveness of marine transport. Our opinion is that the same bodies which approved this law must help the shipping industry invest in these technologies, drive research on them, and promote the creation of a port infrastructure which is adapted to supply LNG and handle the discharges from scrubber systems. At present there are several European incentive programmes, such as TEN-T and Marco Polo, but we do not consider these to be sufficient. For its part, the International Maritime Organization should confirm as soon as possible whether the new lower sulphur levels in fuels will be postponed until 2025. This would eliminate the great uncertainty among shipowners, oil companies and ports regarding the timeline for beginning their future investments and for studying their viability.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

The middle-late Campanian was marked by an increase in the bioprovinciality of calcareous microfossil assemblages into distinct Tethyan, Transitional, and Austral Provinces that persisted to the end of the Maastrichtian. The northwestern Australian margin belonged to the Transitional Province and the absence of key Tethyan marker species such as Radotruncana calcarata and Gansserina gansseri has led petroleum companies operating in the area to use the locally developed KCCM integrated calcareous microfossil zonation scheme. The KCCM zonation is a composite scheme comprising calcareous nannofossil (KCN), planktonic foraminiferal (KPF) and benthonic foraminiferal (KBF) zones. This paper presents the definitions and revisions of Zones KCCM8-19, from the highest occurrence (HO) of Aspidolithus parcus constrictus to the lowest occurrence (LO) of Ceratolithoides aculeus, and builds on our previous early-late Maastrichtian study. The presence of a middle-upper Campanian disconformity is confirmed by microfossil evidence from the Vulcan Sub-basin, Exmouth and Wombat plateaus, and the Southern Carnarvon Platform. In the Vulcan Sub-basin and on the Exmouth Plateau (ODP Hole 762C) the hiatus extends from slightly above the LO of common Rugoglobigerina rugosa to above the LO of Quadrum gothicum. On the Wombat Plateau (ODP Hole 761B) it spans from above the LO of Heterohelix semicostata to above the LO of Quadrum gothicum; and in the Southern Carnarvon Platform the disconformity has its longest duration from above the HO of Heterohelix semicostata to above the LO of Quadrum sissinghii. A significant revision of the events which define Zones KCCM18 and 19 was necessary owing to the observation that the LO of Ceratolithoides aculeus occurs below the HOs of Archaeoglobigerina cretacea and Stensioeina granulata incondita and the LO of common Rugoglobigerina rugosa. In the original zonation these events were considered to be coincident.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

The purpose of this prospective clinical study was to quantify the surgical margin necessary to maximise local disease control for canine soft tissue sarcoma of various grades. This was achieved via gross and histopathologic studies. Fourteen dogs underwent surgical treatment for 15 localised, measurable, subcutaneous sarcomas. Surgery and histopathologic evaluation were performed to standardised protocols. Regular examinations for local recurrence and distant metastases were performed for at least 12 months postoperatively. One hundred percent local disease control was achieved with deep margins >10mm and 93% one year disease-free survival with wide margins (i.e. >10mm laterally and one fascial plane or >10mm in depth). There was one case of recurrence. Fascial planes appear to act as biological barriers to local tumour invasion but this protective effect may be overcome with high-grade lesions.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

The main goal of this work is to determine the true cost incurred by the Republic of Ireland and Northern Ireland in order to meet their EU renewable electricity targets. The primary all-island of Ireland policy goal is that 40% of electricity will come from renewable sources in 2020. From this it is expected that wind generation on the Irish electricity system will be in the region of 32-37% of total generation. This leads to issues resulting from wind energy being a non-synchronous, unpredictable and variable source of energy use on a scale never seen before for a single synchronous system. If changes are not made to traditional operational practices, the efficient running of the electricity system will be directly affected by these issues in the coming years. Using models of the electricity system for the all-island grid of Ireland, the effects of high wind energy penetration expected to be present in 2020 are examined. These models were developed using a unit commitment, economic dispatch tool called PLEXOS which allows for a detailed representation of the electricity system to be achieved down to individual generator level. These models replicate the true running of the electricity system through use of day-ahead scheduling and semi-relaxed use of these schedules that reflects the Transmission System Operator's of real time decision making on dispatch. In addition, it carefully considers other non-wind priority dispatch generation technologies that have an effect on the overall system. In the models developed, three main issues associated with wind energy integration were selected to be examined in detail to determine the sensitivity of assumptions presented in other studies. These three issues include wind energy's non-synchronous nature, its variability and spatial correlation, and its unpredictability. This leads to an examination of the effects in three areas: the need for system operation constraints required for system security; different onshore to offshore ratios of installed wind energy; and the degrees of accuracy in wind energy forecasting. Each of these areas directly impact the way in which the electricity system is run as they address each of the three issues associated with wind energy stated above, respectively. It is shown that assumptions in these three areas have a large effect on the results in terms of total generation costs, wind curtailment and generator technology type dispatch. In particular accounting for these issues has resulted in wind curtailment being predicted in much larger quantities than had been previously reported. This would have a large effect on wind energy companies because it is already a very low profit margin industry. Results from this work have shown that the relaxation of system operation constraints is crucial to the economic running of the electricity system with large improvements shown in the reduction of wind curtailment and system generation costs. There are clear benefits in having a proportion of the wind installed offshore in Ireland which would help to reduce variability of wind energy generation on the system and therefore reduce wind curtailment. With envisaged future improvements in day-ahead wind forecasting from 8% to 4% mean absolute error, there are potential reductions in wind curtailment system costs and open cycle gas turbine usage. This work illustrates the consequences of assumptions in the areas of system operation constraints, onshore/offshore installed wind capacities and accuracy in wind forecasting to better inform the true costs associated with running Ireland's changing electricity system as it continues to decarbonise into the near future. This work also proposes to illustrate, through the use of Ireland as a case study, the effects that will become ever more prevalent in other synchronous systems as they pursue a path of increasing renewable energy generation.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

Methane hydrate is an ice-like substance that is stable at high-pressure and low temperature in continental margin sediments. Since the discovery of a large number of gas flares at the landward termination of the gas hydrate stability zone off Svalbard, there has been concern that warming bottom waters have started to dissociate large amounts of gas hydrate and that the resulting methane release may possibly accelerate global warming. Here, we can corroborate that hydrates play a role in the observed seepage of gas, but we present evidence that seepage off Svalbard has been ongoing for at least three thousand years and that seasonal fluctuations of 1-2°C in the bottom-water temperature cause periodic gas hydrate formation and dissociation, which focus seepage at the observed sites.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

Transit agencies across the world are increasingly shifting their fare collection mechanisms towards fully automated systems like the smart card. One of the objectives in implementing such a system is to reduce the boarding time per passenger and hence reduce the overall dwell time for the buses at the bus stops/bus rapid transit (BRT) stations. TransLink, the transit authority responsible for public transport management in South East Queensland, has introduced ‘GoCard’ technology using the Cubic platform for fare collection on its public transport system. In addition to this, three inner city BRT stations on South East Busway spine are operating as pre-paid platforms during evening peak time. This paper evaluates the effects of these multiple policy measures on operation of study busway station. The comparison between pre and post policy scenarios suggests that though boarding time per passenger has decreased, while the alighting time per passenger has increased slightly. However, there is a substantial reduction in operating efficiency was observed at the station.

Relevância:

20.00% 20.00%

Publicador:

Resumo:

Vehicle detectors have been installed at approximately every 300 meters on each lane on Tokyo metropolitan expressway. Various traffic data such as traffic volume, average speed and time occupancy are collected by vehicle detectors. We can understand traffic characteristics of every point by comparing traffic data collected at consecutive points. In this study, we focused on average speed, analyzed road potential by operating speed during free-flow conditions, and identified latent bottlenecks. Furthermore, we analyzed effects for road potential by the rainfall level and day of the week. It’s expected that this method of analysis will be utilized for installation of ITS such as drive assist, estimation of parameters for traffic simulation and feedback to road design as congestion measures.